Jagan Teki [Tue, 16 Jul 2019 11:57:21 +0000 (17:27 +0530)]
ram: rk3399: Add IO settings
Add IO settings for dram ctl and phy.
IO settings are useful for configuring ctl, phy odt, vref,
mr5, mode select and other needed input output operations
for lpddr4 or any other dramtype sdram.
Right now, this patch added IO setting for all supported
sdram frequencies.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Jagan Teki [Tue, 16 Jul 2019 11:57:01 +0000 (17:27 +0530)]
ram: rk3399: Introduce sys_reg3 for more capacity info
cs0_row, cs1_row and cs1_col needs more bits to show its
correct value, update to make use of both sys_reg2,
sys_reg3.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(Squash similar patches into one patch) Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
Jagan Teki [Tue, 16 Jul 2019 11:56:49 +0000 (17:26 +0530)]
ram: rk3399: Simply existing dram enc macro
Add simplified and meaningful macro for all setting.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(Squash the similar patches into 1 patch) Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
Jagan Teki [Mon, 15 Jul 2019 18:28:54 +0000 (23:58 +0530)]
ram: rk3399: Add rank detection support
Right now the rk3399 sdram driver assume that the board
has configured with 2 channels, so any possibility to
enable single channel on the same driver will encounter
channel #1 data training failure.
Log:
U-Boot TPL board init
sdram_init: data training failed
rk3399_dmc_init DRAM init failed -5
So, add an algorithm that can capable to compute the active
or configured rank with associated channel like
a) do rank loop to compute the active rank, with associated
channel numbers
b) then, succeed the data training only for configured channel
c) preserve the rank for given channel
d) do channel loop for setting the active channel
e) if given rank is zero or inactive on the specific channel,
clear the timings for the associated channel
f) finally, return error if number of channels is zero
Tested in NanoPI-NEO4 since it support single channel sdram
configuration.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(add PI_READ_GATE_TRAINING for LPDDR3 to support rk3399-evb case) Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
Jagan Teki [Mon, 15 Jul 2019 18:28:52 +0000 (23:58 +0530)]
ram: rk3399: Compute stride for 2 channels
stride value from sdram timings can be computed dynamically
based on the determined capacity for the given channel.
Right now these stride values are taken as part of sdram timings
via dtsi, but it possible to use same timings dtsi for given
frequency even though the configured board sdram do support
single channel with different size by dynamically detect the
stride value.
Example, NanoPi NEO4 do have DDR3-1866, but with single channel
and 1GB size with dynamic stride detection it is possible to
use existing rk3399-sdram-ddr3-1866.dtsi whose stride,
number of channels and capacity it support is d efferent.
So, add initial support to calculate the stride value for
2 channels sdram, which is available by default on existing
boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Jagan Teki [Mon, 15 Jul 2019 18:28:48 +0000 (23:58 +0530)]
ram: rockchip: Add debug sdram driver
Add sdram driver to handle debug across rockchip SoCs.
This would help to improve code debugging feature for
sdram drivers in rockchip family, whoever wants to
debug the driver should call these core debug code on
their respective platform sdram drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Jagan Teki [Mon, 15 Jul 2019 18:28:44 +0000 (23:58 +0530)]
ram: rk3399: Move pwrup_srefresh_exit to dram_info
Add pwrup_srefresh_exit to be part of dram_info so-that
the it can help to support pwrup_srefresh_exit in individual
channels while starting pctl in future.
No functionality change.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Jagan Teki [Mon, 15 Jul 2019 18:28:42 +0000 (23:58 +0530)]
ram: rk3399: Use rank mask in wdql data training
Add rank_mask based on the rank number, this would keep
the wdql data training loop based on the desired rank mask
value instead of looping for all values.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Jagan Teki [Mon, 15 Jul 2019 18:28:41 +0000 (23:58 +0530)]
ram: rk3399: Use rank mask in ca data training
Add rank_mask based on the rank number, this would keep
the ca data training loop based on the desired rank mask
value instead of looping for all values.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Jagan Teki [Mon, 15 Jul 2019 18:28:39 +0000 (23:58 +0530)]
ram: rk3399: Handle data training return types
data trainings calls like ca, wl, rg, rl, wdql have proper
return types with -EIO and the return type missed to handle
in data_training function.
This patch, add proper return type checks along with useful
debug statement on each data training calls.
Incidentally this would help to prevent the sdram initialization
hang for single channel dram and when the code is trying to
initialize second channel with proper return type of relevant
data training call might failed.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Jagan Teki [Mon, 15 Jul 2019 18:21:10 +0000 (23:51 +0530)]
clk: rockchip: rk3399: Fix check patch warnings and checks
- CHECK: spaces preferred around that '*'
- CHECK: spaces preferred around that '/'
- CHECK: space preferred before that '|'
- WARNING: macros should not use a trailing semicolon
- CHECK: Unnecessary parentheses around 'fbdiv <= min_fbdiv'
- CHECK: Unnecessary parentheses around 'parent->id == SCLK_MAC'
- CHECK: Unnecessary parentheses around 'parent->dev == clk->dev'
- WARNING: line over 80 characters
- CHECK: Prefer kernel type 'u8' over 'uint8_t'
- Add proper macro definitions arrangements
Note: there are still line over 80 characters and other warnings but
fixing those making code look unreadable, so I kept it as it is.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Jagan Teki [Mon, 15 Jul 2019 18:21:07 +0000 (23:51 +0530)]
ram: rk3399: Move common sdram structures in common header
Move common sdram structures like sdram_cap_info, sdram_base_params
into sdram_common header, this would help to reuse the same
from another controllers like px30.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Jagan Teki [Mon, 15 Jul 2019 18:20:56 +0000 (23:50 +0530)]
ram: rk3399: Fix code warnings
Fix checkpatch warninigs on sdram_rk3399.c like
- Avoid CamelCase
- Unnecessary parentheses
- Alignment should match open parenthesis
- multiple blank lines
- misspelled
- spaces preferred around that '>>'
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Andy Yan [Thu, 4 Jul 2019 06:52:47 +0000 (14:52 +0800)]
rockchip: dts: rk3399: Add spl-boot-order for Rock PI 4
RK3399 use sdhci for eMMC and DW MMC for SD Card, and
spl will only try to boot from SDMMC if we don't specify
other boot device for spl-boot-order. So add sdhci and sdmmc
for spl-boot-order here.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mark Kettenis [Sun, 30 Jun 2019 16:01:53 +0000 (18:01 +0200)]
rockchip: clk: rk3399: handle clk_enable requests for USB3
The "simple" OF glue layer for the Designware USB3 core enables
all refernced clocks. These need to be need to be implemented
otherwise the driver fails to probe. A dummy implementation
that simply returns success is sufficient since the RK3399 comes
out of reset with all clock gates open.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tom Rini [Thu, 18 Jul 2019 15:31:37 +0000 (11:31 -0400)]
Merge branch '2019-07-17-master-imports'
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
Removed one of the defconfig(obsoleted) file
and unused CONFIG_MMC_SPI definition to avoid confusion
about if this board using non-DM stuff or not.
uCP1020 is completely DM free board, tested and runs well.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com> Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some storage devices have multiple hw partitions and both address from
zero, for example eMMC.
However currently block cache invalidation only applies to block
write/erase.
This can cause a problem that data of current hw partition is cached
before switching to another hw partition. And the following read
operation of the latter hw partition will get wrong data when reading
from the addresses that have been cached previously.
To solve this problem, invalidate block cache after a successful
select_hwpart operation.
arm: dts: MediaTek: fix clock order for timer0 node of mt7629.dtsi
The timer0 node has its two clocks written in reversed order. The timer0
is used as the tick timer which causes a problem that the time a delay
function used is 4 times longer.
This patch reverses these two clocks to solve this issue.
Simon Glass [Wed, 10 Jul 2019 17:04:13 +0000 (11:04 -0600)]
chromium: Update docs to clone vboot_reference directly
We don't need a full checkout of Chrome OS to build U-Boot with
Chromium OS verified boot. Update the instructions accordingly and fix a
typo which joins the output directory and defconfig.
Paul Emge [Mon, 8 Jul 2019 23:37:05 +0000 (16:37 -0700)]
CVE-2019-13104: ext4: check for underflow in ext4fs_read_file
in ext4fs_read_file, it is possible for a broken/malicious file
system to cause a memcpy of a negative number of bytes, which
overflows all memory. This patch fixes the issue by checking for
a negative length.
Signed-off-by: Paul Emge <paulemge@forallsecure.com>
Paul Emge [Mon, 8 Jul 2019 23:37:04 +0000 (16:37 -0700)]
CVE-2019-13105: ext4: fix double-free in ext4_cache_read
ext_cache_read doesn't null cache->buf, after freeing, which results
in a later function double-freeing it. This patch fixes
ext_cache_read to call ext_cache_fini instead of free.
Signed-off-by: Paul Emge <paulemge@forallsecure.com>
Paul Emge [Mon, 8 Jul 2019 23:37:03 +0000 (16:37 -0700)]
CVE-2019-13103: disk: stop infinite recursion in DOS Partitions
part_get_info_extended and print_partition_extended can recurse infinitely
while parsing a self-referential filesystem or one with a silly number of
extended partitions. This patch adds a limit to the number of recursive
partitions.
Signed-off-by: Paul Emge <paulemge@forallsecure.com>
arm: qemu: fix failure in flash initialization if booting from TF-A
If U-Boot is loaded and started from TF-A (you need to change
SYS_TEXT_BASE to 0x60000000), it will hang up at flash initialization.
If secure mode is off (default, or -machine virt,secure=off) at qemu,
it will provide dtb with two flash memory banks:
flash@0 {
bank-width = <0x4>;
reg = <0x0 0x0 0x0 0x4000000 0x0 0x4000000 0x0 0x4000000>;
compatible = "cfi-flash";
};
If secure mode is on, on the other hand, qemu provides dtb with 1 bank:
flash@0 {
bank-width = <0x4>;
reg = <0x0 0x4000000 0x0 0x4000000>;
compatible = "cfi-flash";
};
As a result, flash_init()/flash_get_size() will eventually fail.
With this patch applied, relevant CONFIG values are modified.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently, CONFIG_TFABOOT is located in armv8/fsl-layerscape Kconfig,
but it will be also useful for other targets if some additional
configuration are necessary.
So move it to arch/arm/Kconfig.
Please note that CONFIG_TFABOOT still depends on
CONFIG_ARCH_SUPPORT_TFABOOT and so the menu won't come up
if any target doesn't need its own customization for TF-A boot.
This will maintain the compatibility.
At the moment mkenvimage has two separate read paths: One to read from
a potential pipe, while dynamically increasing the buffer size, and a
second one using mmap(2), using the input file's size. This is
problematic for two reasons:
- The "pipe" path will be chosen if the input filename is missing or
"-". Any named, but non-regular file will use the other path, which
typically will cause mmap() to fail:
$ mkenvimage -s 256 -o out <(echo "foo=bar")
- There is no reason to have *two* ways of reading a file, since the
"pipe way" will always work, even for regular files.
Fix this (and simplify the code on the way) by always using the method
of dynamically resizing the buffer. The existing distinction between
the two cases will merely be used to use the open() syscall or not.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Sun, 30 Jun 2019 01:45:00 +0000 (02:45 +0100)]
tools: mkenvimage: Fix reading from slow pipe
It is perfectly fine for the read(2) syscall to return with less than
the requested number of bytes read (short read, see the "RETURN VALUE"
section of the man page). This typically happens with slow input
(keyboard, network) or with complex pipes.
So far mkenvimage expects the exact number of requested bytes to be
read, assuming an end-of-file condition otherwise. This wrong behaviour
can be easily shown with:
$ (echo "foo=bar"; sleep 1; echo "bar=baz") | mkenvimage -s 256 -o out -
The second line will be missing from the output.
Correct this by checking for any positive, non-zero return value.
This fixes a problem with a complex pipe in one of my scripts, where
the environment consist of two parts.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Alexander Dahl <ada@thorsis.com>
Frank Wunderlich [Sat, 29 Jun 2019 09:36:20 +0000 (11:36 +0200)]
env: mmc: add erase-function
this adds erase environment for mmc storage
squashed fixes:
- add CONFIG_CMD_ERASEENV
- env: erase redundant offset if defined
- changes mentioned by Simon
- fix whitespaces around errmsg
Suggested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Signed-off-by: Frank Wunderlich <frank-w@public-files.de> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Frank Wunderlich [Sat, 29 Jun 2019 09:36:19 +0000 (11:36 +0200)]
env: register erase command
this patch adds basic changes for adding a erase-subcommand to env
with this command the environment stored on non-volatile storage written
by saveenv can be cleared.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
squashed fixes
- start message with "Erasing"
- mark erase-function as optional
- env: separate eraseenv from saveenv
Suggested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Marek Vasut [Wed, 26 Jun 2019 22:17:27 +0000 (00:17 +0200)]
common: Fix autocompletion with CONFIG_CMDLINE_PS_SUPPORT
The autocompletion did not work if CONFIG_CMDLINE_PS_SUPPORT was enabled
because U-Boot was comparing the prompt string with CONFIG_SYS_PROMPT .
While this works if CONFIG_CMDLINE_PS_SUPPORT is disabled, this no longer
works if it's enabled because user can override the PS1 . Fix this by
checking prompt string against the current PS1 value.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@konsulko.com>
Sven Schwermer [Mon, 24 Jun 2019 11:03:34 +0000 (13:03 +0200)]
regulator: Allow enabling GPIO regulator
Drivers need to be able to enable regulators that may be implemented as
GPIO regulators. Example: fsl_esdhc enables the vqmmc supply which is
commonly implemented as a GPIO regulator in order to switch between I/O
voltage levels.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de> Reviewed-by: Lukasz Majewski <lukma@denx.de>
Sven Schwermer [Mon, 24 Jun 2019 11:03:33 +0000 (13:03 +0200)]
regulator: Factor out common enable code
In preparation of being able to enable/disable GPIO regulators, the
code that will be shared among the two kinds to regulators is factored
out into its own source files.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de> Reviewed-by: Lukasz Majewski <lukma@denx.de>
When a crash occurs in thumb mode the crash dump is incorrect. This is due
to the usage of a non-existing configuration variable CONFIG_ARM_THUMB in
the definition of macro thumb_mode(regs).
Use CONFIG_IS_ENABLED(SYS_THUMB_BUILD) to detect that the code has been
compiled for thumb mode. Remove ARM_THUMB from config_whitelist.txt.
With the patch crash dumps indicate thumb mode correctly.
projects / u-boot.git / log