Marek Vasut [Tue, 19 Feb 2019 00:07:21 +0000 (01:07 +0100)]
ARM: socfpga: Clear PL310 early in SPL
On SoCFPGA Gen5 systems, it can rarely happen that a reboot from Linux
will result in stale data in PL310 L2 cache controller. Even if the L2
cache controller is disabled via the CTRL register CTRL_EN bit, those
data can interfere with operation of devices using DMA, like e.g. the
DWMMC controller. This can in turn cause e.g. SPL to fail reading data
from SD/MMC.
The obvious solution here would be to fully reset the L2 cache controller
via the reset manager MPUMODRST L2 bit, however this causes bus hang even
if executed entirely from L1 I-cache to avoid generating any bus traffic
through the L2 cache controller.
This patch thus configures and enables the L2 cache controller very early
in the SPL boot process, clears the L2 cache and disables the L2 cache
controller again.
The reason for doing it in SPL is because we need to avoid accessing any
of the potentially stale data in the L2 cache, and we are certain any of
the stale data will be below the OCRAM address range. To further reduce
bus traffic during the L2 cache invalidation, we enable L1 I-cache and
run the invalidation code entirely out of the L1 I-cache.
Marek Vasut [Wed, 13 Feb 2019 20:50:25 +0000 (21:50 +0100)]
ARM: cache: Fix incorrect bitwise operation
The loop implemented in the code is supposed to check whether the
PL310 operation register has any bit from the mask set. Currently,
the code checks whether the PL310 operation register has any bit
set AND whether the mask is non-zero, which is incorrect. Fix the
conditional.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dalon Westergreen <dwesterg@gmail.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Tom Rini <trini@konsulko.com> Fixes: 93bc21930a1b ("armv7: add PL310 support to u-boot")
Jan Kiszka [Thu, 3 Jan 2019 08:08:42 +0000 (09:08 +0100)]
cmd: Kconfig: LED command depends on LED subsystems
Without CONFIG_LED, we get
cmd/built-in.o: In function `show_led_state':
cmd/led.c:40: undefined reference to `led_get_state'
cmd/built-in.o: In function `do_led':
cmd/led.c:99: undefined reference to `led_get_by_label'
cmd/led.c:108: undefined reference to `led_set_state'
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Tom Rini [Wed, 20 Feb 2019 17:28:40 +0000 (12:28 -0500)]
Merge git://git.denx.de/u-boot-x86
- Add support for sound.
Albeit the big changeset, changes are pretty limited to x86 only and a
few new sound drivers used by x86 so I think it would be good to have
this in the next release.
board: toradex: turn off lcd backlight before OS handover
U-Boot typically tears down the display controller before handing
control over to Linux. On LCD displays disabling pixel clock leads to a
fading out effect with vertical/horizontal lines. Make sure to disable
back light before booting Linux.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com> Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Peter Robinson [Wed, 20 Feb 2019 12:17:29 +0000 (12:17 +0000)]
nyan-big: drop CONFIG_KEYBOARD
The CONFIG_KEYBOARD does nothing as it's legacy and unused
so just drop it from the config.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Peter Robinson [Wed, 20 Feb 2019 12:17:28 +0000 (12:17 +0000)]
Kconfig: tegra: Migrate TEGRA_KEYBOARD
Migrate TEGRA_KEYBOARD from headers to Kconfig, only the seaboard uses it but we
drop CONFIG_KEYBOARD as the driver doesn't use the legacy drv_keyboard_init.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Peter Robinson [Wed, 20 Feb 2019 12:17:27 +0000 (12:17 +0000)]
Kconfig: tegra: Migrate USB_EHCI_TEGRA
Migrate USB_EHCI_TEGRA from headers to Kconfig
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Marek Vasut <marex@denx.de> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Peter.Chubb@data61.csiro.au Cc: Lucas Stach <dev@lynxeye.de> Cc: Stefan Agner <stefan.agner@toradex.com> Cc: Alban Bedel <alban.bedel@avionic-design.de> Cc: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Peter Robinson [Wed, 20 Feb 2019 12:17:26 +0000 (12:17 +0000)]
Kconfig: tegra: Migrate SYS_I2C_TEGRA
Migrate SYS_I2C_TEGRA from headers to Kconfig
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Heiko Schocher <hs@denx.de> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Peter.Chubb@data61.csiro.au Cc: Lucas Stach <dev@lynxeye.de> Cc: Stefan Agner <stefan.agner@toradex.com> Cc: Alban Bedel <alban.bedel@avionic-design.de> Cc: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Jonathan Hunter [Tue, 12 Feb 2019 16:03:14 +0000 (16:03 +0000)]
ARM: tegra: Reserve 32MB for the Linux kernel
Booting recently Linux -next kernels on 32-bit Tegra devices has been
failing when using the 'multi_v7_defconfig' kenrel configuration because
the size of has grown such that it is overwriting the FDT blob.
Current Linux -next kernels built with the 'multi_v7_defconfig' have a
total size of ~19.5MB (where .text is ~12.5MB, .data is ~6.5MB and .bss
is ~0.5MB). Therefore, increase the memory location reserved for the
Linux kernel to 32MB from 16MB for 32-bit Tegra devices.
This change has been boot tested on Tegra20 Ventana, Tegra30 Cardhu and
Tegra124 Jetson TK1 with the Linux next tree (20190212).
Signed-off-by: Jonathan Hunter <jonathanh@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Tristan Bastian [Thu, 14 Feb 2019 23:25:49 +0000 (00:25 +0100)]
ARM: tegra: enable ums on nyan boards
This patch enables UMS on the nyan devices like the nyan-big.
A patch like this has been sent in by Stephen Warren some time ago for
other tegra devices: commit e6607cffef965011ef0ddc0fbe6f4b7c0d53aeec.
But the nyan devices never received that functionality.
Signed-off-by: Tristan Bastian <tristan-c.bastian@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Tristan Bastian [Wed, 16 Jan 2019 18:49:55 +0000 (19:49 +0100)]
nyan-big: change spi delay
Internal keyboard of nyan-big is only working when cold booting by pressing [reload/refresh]+[power] button.
With this patch keyboard is working by only pressing [power] button.
Signed-off-by: Tristan Bastian <tristan-c.bastian@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Peter Robinson [Sun, 16 Sep 2018 17:22:58 +0000 (18:22 +0100)]
tegra20: common: fix USB_EHCI_TXFIFO_THRESH value
All other Tegra devices that define USB_EHCI_TXFIFO_THRESH use hex
representation, fix tegra20 to be the same format.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Peter Robinson [Sun, 16 Sep 2018 17:22:57 +0000 (18:22 +0100)]
tegra: cleanup dangling comments in include/configs
There's a number of dangling comments in various tegra configs post migrations
of various configs so lets clean them up.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Peter.Chubb@data61.csiro.au Cc: Lucas Stach <dev@lynxeye.de> Cc: Stefan Agner <stefan.agner@toradex.com> Cc: Alban Bedel <alban.bedel@avionic-design.de> Cc: Allen Martin <amartin@nvidia.com> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Sun, 17 Feb 2019 03:25:02 +0000 (20:25 -0700)]
x86: broadwell: Don't bother probing the PCH for pinctrl
At present the pinctrl probes the PCH but since it only uses it to obtain
a PCI address, this is no necessary. Avoiding this fixes one of the two
co-dependent loops in broadwell.
This driver really should be a proper pinctrl driver, but for now it
remains a syscon device.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 17 Feb 2019 03:24:56 +0000 (20:24 -0700)]
sandbox: sound: Silence sound for testing
When testing the sound system we don't need the hear the beeps. The
testing works by checking the data that would be emitted. Add a
device-tree property to silence the sound, and enable it for testing.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 17 Feb 2019 03:24:55 +0000 (20:24 -0700)]
sound: Add support for Intel HDA
The Intel High-definition Audio is a newer-generation audio system which
provides for transfer of a large number of audio stream, each containing
up to 16 channels.
Add support for HDA as a library which can be used by other drivers.
U-Boot currently uses only two channels (stereo).
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 17 Feb 2019 03:24:54 +0000 (20:24 -0700)]
sound: Add uclass operations for beeping
Some audio codecs such as Intel HDA do not need to use digital data to
play sounds, but instead have a way to emit beeps. Add this interface as
an option. If the beep interface is not supported, then the sound uclass
falls back to the I2S interface.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 17 Feb 2019 03:24:51 +0000 (20:24 -0700)]
pch: Add ioctl support
At present the PCH has 4 operations and these are reasonably widely used
in the drivers. But sometimes we want to add rarely used operations, and
each of these currently adds to the size of the PCH operations table.
Add an ioctl() method which can be easily expanded without any more impact
on the operations table.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 17 Feb 2019 03:24:50 +0000 (20:24 -0700)]
sandbox: pch: Add a test for the PCH uclass
This uclass currently has no tests. Add a sandbox driver and some simple
tests to provide basic coverage.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: Use "sandbox,pch" for the compatible string, for consistency] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 17 Feb 2019 03:24:49 +0000 (20:24 -0700)]
x86: sandbox: pch: Add a CONFIG option for PCH
At present this uclass is selected only on x86. In order to add a test for
it, it must also support sandbox. Create a new CONFIG_PCH option and
enable it on x86 and sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 17 Feb 2019 03:24:48 +0000 (20:24 -0700)]
x86: link: Increase malloc size and decrease code size
At present link does not boot since it has outgrown its pre-relocation
malloc() size and its assigned code area. Increase the former and drop
EFI loader support, which adds about 45KB!
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 17 Feb 2019 03:24:45 +0000 (20:24 -0700)]
sandbox: Add a note about the growing state_info struct
This struct is getting larger and in some cases is being used for things
which would be better put into a driver. For example hwspinlock is not
used outside of sandbox_hwspinlock.c.
Add a note to encourage people to put things elsewhere.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 17 Feb 2019 03:24:43 +0000 (20:24 -0700)]
gpio: Use case-insentive matching on the GPIO name
Allow the 'gpio' command to match GPIO bank names regardless of the case
of each. While these are generally in upper case, it is useful to be able
to provide lower case with the command.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 17 Feb 2019 03:24:42 +0000 (20:24 -0700)]
gpio: Show inactive GPIOs when explicitly requested
At present the gpio command only shows GPIOs which are marked as in use.
This makes sense with 'gpio status' since we already have the '-a' flag
to indicate that all GPIOs should be shown. But when a particular GPIO is
requested, it seems better to always display it. At present the request is
simply ignored.
For example if GPIO a10 is not in use, then:
> gpio status a10
shows nothing, not even the function being used for that GPIO. With this
change, it shows the pin status:
> gpio status a10
a10: input: 0 [ ]
Add an extra parameter for this to avoid changing the existing flag
parameter.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the 'gpio' command in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 17 Feb 2019 03:24:39 +0000 (20:24 -0700)]
i2c: designware: Add error checking on init
At present this driver does not check whether it is able to actually
communicate with the I2C controller. It prints a timeout message but still
considers the probe to be successful.
To fix this, add some checking that the init succeeds.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Sun, 17 Feb 2019 03:24:38 +0000 (20:24 -0700)]
dm: syscon: Don't require a regmap for PCI devices
At present it is not possible to use the syscon devices for PCI devices
since a regmap is required. Since PCI uses a 3-cell address the conversion
of the 'reg' property to an address always fails. In any case, the regmap
is not useful with PCI since devices are accessed through the PCI bus
which regmap does not support.
Add a special case for PCI syscon devices, so that they don't set up a
regmap.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 17 Feb 2019 03:24:37 +0000 (20:24 -0700)]
log: Allow #define LOG_DEBUG to enable logging in a file
At present it is possible to '#define DEBUG' at the top of a file which
causes all debug() statements in that file to become active. There is
currently no equivalent with logging, but this is a useful function.
Add a LOG_DEBUG define along with documentation.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Sat, 16 Feb 2019 21:36:29 +0000 (16:36 -0500)]
omap3_beagle: Update for DM SPL support
- Switch to using the omap3-u-boot.dtsi file for needed properties.
- Remove a few SPL features to free up more SRAM space.
- Switch CONFIG_SYS_TEXT_BASE to the normal default, we don't need to
worry about X-Loader at this point anymore.
- A few related updates to SPL options as part of switching to DM SPL.
Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Derald D. Woods <woods.technical@gmail.com>
Adam Ford [Sat, 16 Feb 2019 19:31:24 +0000 (13:31 -0600)]
ARM: omap3_logic: Enable SPL booting device tree
With the generic omap3-u-boot.dtsi file available, this patch
increased the memory of the various incarnations of the omap3_logic
board, and points their respective u-boot.dtsi files to the newly
created generic one, and removes the PLATDATA from the board file.
These are all done at once because the're all utilizing the same
omap3logic.c board file.
Adam Ford [Fri, 15 Feb 2019 02:13:53 +0000 (20:13 -0600)]
ARM: da8xxevm: Add NAND instructions for da850-evm to README
The README.da850 file continues information on how to burn NAND
for the LCDK, but not the DA850-EVM. This patch adds both the
commands and dip switch instructions for burning and booting
NAND.
Adam Ford [Wed, 13 Feb 2019 19:06:37 +0000 (13:06 -0600)]
ARM: da850evm: Increase Malloc Size
The SPI NOR frameware was recently updated, but they require a little
more memory that we had previosly allocated, so it stopped booting.
This patch doubles the size of CONFIG_SPL_SYS_MALLOC_F_LEN to 0x800.
Fixes: c4e8862308d4 ("mtd: spi: Switch to new SPI NOR framework") Signed-off-by: Adam Ford <aford173@gmail.com>
hikey: Allow environment to store in eMMC and increase bootdelay
Current Hikey configuration allows us to store u-boot environment on uSD
card. But this will be useless if uSD card is not inserted, hence use
the onboard eMMC memory for storing environment at Boot1 partition.
While we are at it, let's increase the boot delay to 10s also.
SPL currently does not check uImage CRCs when loading U-Boot.
This patch adds checking the uImage CRC when SPL loads U-Boot. It does
this by reusing the existing config option SPL_CRC32_SUPPORT to allow
leaving out the CRC check on boards where the additional code size or
boot time is a problem (adding the CRC check currently adds ~1.4 kByte
to flash).
The SPL_CRC32_SUPPORT config option now gets enabled by default if SPL
support for legacy images is enabled to check the CRC on all boards
that don't actively take countermeasures.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Currently there are two problems in 'bootelf -p' (load elf by segments)
command:
- bss section is not flushed, so booted elf can have non zero values
in bss;
- at least on ARM there are 'CACHE: Misaligned operation at
range...' warnings
Use p_memsz instead of p_filesz during cache flushing for elf segment.
p_filesz doesn't include zero initialized memory (e.g. bss section),
which also should be flushed.
Align these cache flushes to line boundaries.
Signed-off-by: Kurban Mallachiev <mallachiev@ispras.ru>
This commit converts the brxre1 board to DM,
for this we have todo following things:
- add a devicetree-file for this board
- drop all obsolete settings from board header-file
- use dm_i2c_xxx calls for read/write to the resetcontroller
- request gpios before operate them
Serues-cc: trini@konsulko.com Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Before the patch scsi would report the same device number for all SCSI
devices, e.g.
Device 0: (1:0) Vendor: ATA Prod.: Crucial_CT128M55 Rev: MU01
Type: Hard Disk
Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)
Device 0: (1:0) Vendor: ATA Prod.: Rev:
Type: Hard Disk
Capacity: not available
With the patch the same device number is reported as is used in
scsi_read():
Device 0: (1:0) Vendor: ATA Prod.: Crucial_CT128M55 Rev: MU01
Type: Hard Disk
Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)
Device 1: (1:0) Vendor: ATA Prod.: Rev:
Type: Hard Disk
Capacity: not available
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Peng Ma [Wed, 30 Jan 2019 11:19:40 +0000 (19:19 +0800)]
configs: ls1021a: enable sata configs for all ls1021a defconfigs
Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls1021a
defconfigs that missing one of them or more.
enable CONFIG_DM_MMC for some defconfigs to support CONFIG_BLK
Support sata for all ls1021a defconfigs
Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Peng Ma [Wed, 30 Jan 2019 11:18:43 +0000 (19:18 +0800)]
configs: ls1012afrwy: enable sata configs for all ls1012afrwy defconfigs
Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls1012afrwy
and ls1012afrwy defconfigs that missing one of them or more.
Support sata for all ls1012afrwy defconfigs
Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Peng Ma [Wed, 30 Jan 2019 11:17:44 +0000 (19:17 +0800)]
configs: ls208xa: enable sata configs for all ls208xa defconfigs
Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls208xardb
and ls208xaqds defconfigs that missing one of them or more.
enable CONFIG_DM_MMC for some defconfigs to support CONFIG_BLK
Support sata for all ls208xa defconfigs
Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Peng Ma [Wed, 30 Jan 2019 11:16:08 +0000 (19:16 +0800)]
configs: ls1088a: enable sata configs for all ls1088a defconfigs
Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls1088ardb
and ls1088aqds defconfigs that missing one of them or more.
Support sata for all ls1088a defconfigs
Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Peng Ma [Wed, 30 Jan 2019 11:14:47 +0000 (19:14 +0800)]
configs: ls1046a: enable sata configs for all ls1046a defconfigs
Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls1046ardb
and ls1046aqds defconfigs that missing one of them or more.
enable CONFIG_DM_MMC for some defconfigs to support CONFIG_BLK
Support sata for all ls1046a defconfigs
Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Peng Ma [Wed, 30 Jan 2019 11:13:32 +0000 (19:13 +0800)]
configs: ls1043aqds: enable sata configs for all ls1043aqds defconfigs
Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls1043aqds
defconfigs that missing one of them or more.
Support sata for all ls1043aqds defconfigs
Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Peng Ma [Wed, 30 Jan 2019 11:11:49 +0000 (19:11 +0800)]
armv8: ls1043a: move SCSI_AHCI and SCSI to arm/Kconfig
remove SCSI and SCSI_AHCI configs for ls1043ardb due to no sata interface
support.
this changed is to fixed the ls1043ardb compile warning as fallows:
===================== WARNING ======================
This board does not use CONFIG_DM_SCSI. Please update
the storage controller to use CONFIG_DM_SCSI before the
v2019.07 release. Failure to update by the deadline may
result in board removal.See doc/driver-model/MIGRATION.txt
for more info.
====================================================
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[PK: reword the patch subject] Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
projects / u-boot.git / log