doc: board: j721e_evm: Add documentation for firmware loading
Add documentation for loading firmwares to be used by remote cores in
the system including the environment variables that has to be set to
load the firmwares.
env: ti: j721e-evm: Add env variable to power on & reset QSGMII PHY in J7200 EVM
MAIN CPSW0 requires the PHY to be powered on and reset for QSGMII
operation. Add a env variable to configure driving "0" on ENET_EXP_PWRDN
controlled by GPIO EXPANDER2 (I2C Addr: 0x22), PIN: 17 and driving "1"
on ENET_EXP_RESETZ controlled by GPIO EXPANDER2 (I2C Addr: 0x22),
PIN: 18.
ARM: dts: k3-j721e: Add support for USB3 in USB0 instance
Configure the parent clock of wiz3_pll0_refclk to the internal clock
required for USB3 to be functional and also remove "ti,usb2-only"
property as it now supports USB3 mode. This has properties specific to
u-boot on top of DT present in v5.13 of Linux Kernel.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210721155849.20994-12-kishon@ti.com
phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC
Add support for WIZ module present in TI's J721E SoC. WIZ is a SERDES
wrapper used to configure some of the input signals to the SERDES. It is
used with both Sierra(16G) and Torrent(10G) SERDES. This driver configures
three clock selects (pll0, pll1, dig) and supports resets for each of the
lanes.
This is an adaptation of the linux driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210721155849.20994-10-kishon@ti.com
Alan Douglas [Wed, 21 Jul 2021 15:58:36 +0000 (21:28 +0530)]
phy: cadence: Add driver for Sierra PHY
Add a Sierra PHY driver with PCIe and USB support.
This driver is a port from the mainline linux driver.
The PHY has multiple lanes, which can be configured into
groups, and a generic PHY device is created for each group.
There are two resets controlling the overall PHY block, one
to enable the APB interface for programming registers, and
another to enable the PHY itself. Additionally there are
resets for each PHY lane.
The PHY can be configured in hardware to read register
settings from ROM, or they can be written by the driver.
The sequence of operation on startup is to enable the APB
bus, write the PHY registers (if required) for each lane
group, and then enable the PHY. Each group of lanes
can then be individually controlled using the power_on()/
power_off() function for that generic PHY
One difference with the linux driver is that the PHY is
always reset after it is powered-on. This is because role
switching is not supported in u-boot and the cable
orientation is handled by the PHY reset.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Signed-off-by: Alan Douglas <adouglas@cadence.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210721155849.20994-8-kishon@ti.com
dt-bindings: ti-serdes-mux: Add defines for AM64 SoC
AM64 has a single lane SERDES which can be configured to be used
with either PCIe or USB. Define the possilbe values for the SERDES
function in AM64 SoC here.
arm64: zynqmp: Move USB3 PHY properties from DWC3 node to USB node
Move the PHY properties from DWC3 node to USB node in ZynqMP DTs as here
the USB3 PHY used is PSGTR, which is connected to Xilinx USB core. This
PHY initialization should be handled from Xilinx USB core as the
prerequisite register configurations are done here only.
Signed-off-by: Manish Narani <manish.narani@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add kernel_comp_addr_r, kernel_comp_size env variables for zynqmp and
versal to be able to use the compressed kernel Image(.gz,.bz2,.lzma,.lzo)
using booti command.
Signed-off-by: Raju Kumar Pothuraju <raju.kumar-pothuraju@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 14 Jul 2021 07:07:04 +0000 (09:07 +0200)]
arm64: versal: Drop default definitions of CONFIG_SYS_PBSIZE
It is default value which had been converted by commit 432e39806805
("include/configs: drop default definitions of CONFIG_SYS_PBSIZE"). That's
why also remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 13 Jul 2021 14:49:04 +0000 (16:49 +0200)]
arm64: zynqmp: Enable reset and poweroff via sysreset framework
reset and poweroff are called via hooks in psci driver which is going
around sysreset framework that's why enable sysreset drivers and do reset
and poweroff via this framework. Using this flow will allow us to call
SYSTEM_WARM_RESET based on psci 1.1 spec which can be calles with reset -w
command.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 13 Jul 2021 14:39:26 +0000 (16:39 +0200)]
arm64: zynqmp: Do not define do_reset() if sysreset is enabled
The SPL can also be compiled with sysreset drivers just fine, so
update the condition to cater for that option.
The same change was done by commit efa1a62ad2dd ("ARM: imx8m: Do not define
do_reset() if sysreset is enabled").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 13 Jul 2021 14:53:46 +0000 (16:53 +0200)]
psci: Do not define do_poweroff() if CONFIG_SYSRESET_CMD_POWEROFF is enabled
CONFIG_SYSRESET_CMD_POWEROFF defines do_poweroff() in sysreset-uclass.c
that's why don't define it twice when both CONFIG_SYSRESET_CMD_POWEROFF and
CONFIG_CMD_POWEROFF are enabled. CONFIG_SYSRESET_CMD_POWEROFF depends on
CONFIG_CMD_POWEROFF.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for xilinx multirate(MRMAC) ethernet driver.
This driver uses multichannel DMA(MCDMA) for data transfers of MRMAC.
Added support for 4 ports of MRMAC for speeds 10G and 25G.
MCDMA supports upto 16 channels but in this driver we have setup only
one channel which is enough.
Tested 10G and 25G on all 4 ports.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
net: ethtool: Add ethernet speed macros for higher speeds
Add speed macro's for higher ethernet speeds to be used in u-boot
networking drivers. Added Macros for speeds 14G, 20G, 25G, 40G, 50G,
56G, 100G and 200G inline with linux.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 1 Jul 2021 17:01:42 +0000 (19:01 +0200)]
clk: zynqmp: Add support for enabling clock on lpd_lsbus
lpd_lsbus is clock which is used by many IPs like dmas, gems, gpio, sdhcis,
spis, ttcs, uarts, watchdog that's why make sense to also enable access to
change this clock. For this clock you already get the rate.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mike Looijmans [Fri, 2 Jul 2021 08:28:36 +0000 (10:28 +0200)]
xilinx: Return ENVL_NOWHERE instead of ENVL_UNKNOWN
The system refuses to boot without any environment, so return ENVL_NOWHERE when
there's nowhere to store the environment instead of ENVL_UNKNOWN.
This fixes that the board won't boot from eMMC when CONFIG_ENV_IS_IN_FAT is not
defined, for example. Similar for other combinations.
Fixes: 1025bd098aa8 "xilinx: zynqmp: Add support for saving variables" Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 9 Jul 2021 11:53:44 +0000 (05:53 -0600)]
mmc: zynq_sdhci: Make variables/structure static
All these variables/structure are local and should be static.
Issues are reported by sparse:
drivers/mmc/zynq_sdhci.c:49:11: warning: symbol 'zynqmp_iclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:50:11: warning: symbol 'zynqmp_oclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:53:11: warning: symbol 'versal_iclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:54:11: warning: symbol 'versal_oclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:546:24: warning: symbol 'arasan_ops' was not declared. Should it be static?
Michal Simek [Fri, 9 Jul 2021 11:53:43 +0000 (05:53 -0600)]
mmc: zynq_sdhci: Fix kernel doc warnings
Fix these kernel doc warnings:
drivers/mmc/zynq_sdhci.c:181: warning: contents before sections
drivers/mmc/zynq_sdhci.c:236: warning: contents before sections
drivers/mmc/zynq_sdhci.c:291: warning: contents before sections
drivers/mmc/zynq_sdhci.c:297: warning: Function parameter or member 'degrees' not described in 'sdhci_versal_sdcardclk_set_phase'
drivers/mmc/zynq_sdhci.c:354: warning: contents before sections
drivers/mmc/zynq_sdhci.c:360: warning: Function parameter or member 'degrees' not described in 'sdhci_versal_sampleclk_set_phase'
drivers/mmc/zynq_sdhci.c:467: warning: contents before sections
mmc: zynq_sdhci: Split set_tapdelay function to in and out
Split arasan_zynqmp_set_tapdelay() to handle input and output tapdelays
separately. This is required to handle zero values for ITAP and OTAP
values. If we dont split, we will have to remove the if() in the
function, which makes ITAP values to be overwritten when OTAP values are
called to set and vice-versa.
Restrict tap_delay value calculated to max allowed 8 bits for ITAP and 6
bits for OTAP for ZynqMP.
mmc: zynq_sdhci: Allow configuring zero Tap values
Allow configuring ITAP and OTAP values with zero to avoid failures in
some cases (one of them is SD boot mode). Legacy, SDR12 modes require
to program the ITAP and OTAP values as zero, whereas for SDR50 and SDR104
modes ITAP value is zero.
In SD boot mode firmware configures the SD ITAP and OTAP values and
in this case u-boot has to re-configure required tap values(including zero)
based on the operating mode.
xilinx: zynqmp: increase CONFIG_SYS_SPL_MALLOC_SIZE to 16MB
commit 03f1f78a9b44 ("spl: fit: Prefer a malloc()'d buffer for loading
images")' changed the way buffer allocation worked for SPL to a more
flexible method.
For xilinx zynqmp the 1MB buffer is not necessarily enough when dealing
with complex fit images (e.g. containing FPGA/TF-A/OP-TEE/U-Boot
proper), which can easily reach up to 10MB, so increase the default
CONFIG_SYS_SPL_MALLOC_SIZE size to 16MB to cover more advanced
scenarios.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Commit b81406db51a6 ("arm: serial: Add debug UART capability to the
pl01x driver") add supports to use pl01x as a debug UART. However,
due to CONFIG_IS_ENABLED macro requires CONFIG_SPL_* prefix, the
_debug_uart_init() would not choose TYPE_PL011 in SPL build. This
patch fixes the bug by judging CONFIG_DEBUG_UART_PL011 explicitly.
Signed-off-by: Chen Baozi <chenbaozi@phytium.com.cn> Reviewed-by: Simon Glass <sjg@chromium.org>
In the commit c982874e930d ("efi_loader: refactor
efi_setup_loaded_image()"), setjmp-related definitions were moved to
efi_loaded_image_obj in efi_loader.h. So setjmp.h is no longer
refererenced in efi_api.h.
This also fixes some error when efi_api.h will be included in
mkeficapsule.c.
If capsule authentication is disabled and yet a capsule file is signed,
its signature must be removed from image data to flush.
Otherwise, the firmware will be corrupted after update.
Fixes: 04be98bd6bcf ("efi: capsule: Add support for uefi capsule
authentication") Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
BIOS Release Date must be in format mm/dd/yyyy and must be release date.
U-Boot currently sets BIOS Release Date from U_BOOT_DMI_DATE macro which is
generated from current build timestamp.
Fix this issue by setting U_BOOT_DMI_DATE macro to U-Boot version which is
better approximation of U-Boot release date than current build timestamp.
Current U-Boot versioning is in format yyyy.mm so as a day choose 01.
Some operating systems are using BIOS Release Date for detecting when was
SMBIOS table filled or if it could support some feature (e.g. BIOS from
1990 cannot support features invented in 2000). So this change also ensures
that recompiling U-Boot from same sources but in different year does not
change behavior of some operating systems.
Macro U_BOOT_DMI_DATE is not used in other file than lib/smbios.c
so remove it from global autogenerated files and also from Makefile.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
* remove duplicate heading to avoid build error with 'make htmldocs'
* length of underlines must match header
* use appropriate header levels
* fix type %s/linux/Linux/
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
serial: pl011: Resend the character if FIFO is full in debug uart
pl01x_putc() might return -EAGAIN if there was no space in FIFO. In that
case, high-level caller should wait until there is space and resend the
character.
Signed-off-by: Chen Baozi <chenbaozi@phytium.com.cn> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Peter Hoyes [Mon, 12 Jul 2021 14:04:21 +0000 (15:04 +0100)]
armv8: Initialize CNTFRQ if at highest exception level
CNTFRQ_EL0 is only writable from the highest supported exception
level on the platform. For Armv8-A, this is typically EL3, but
technically EL2 and EL3 are optional so it may need to be
initialized at EL2 or EL1. For Armv8-R, the highest exception
level is always EL2.
This patch moves the initialization outside of the switch_el
block and uses a new macro branch_if_not_highest_el which
dynamically detects whether it is at the highest supported
exception level.
Linux's docs state that CNTFRQ_EL0 should be initialized by the
bootloader. If not set, the the U-Boot prompt countdown hangs.
Stephan Gerhold [Wed, 14 Jul 2021 08:56:26 +0000 (10:56 +0200)]
serial: serial_msm: Delay initialization to let pins stabilize
For some reason, the DragonBoard 410c aborts autoboot immediately if
U-Boot is started without LK. It looks like it picks up a single broken
character via serial and therefore believes a key was pressed to abort
autoboot.
After some debugging, it seems like adding some delay after pinctrl
setup but before UART initialization fixes the issue. It's also worth
mentioning that unlike when booting from LK, the pinctrl setup is
actually necessary when booting U-Boot without LK since UART is broken
if the pinctrl line is removed.
I suspect that reconfiguring the pins might take some time to stabilize
and if the UART controller is enabled too quickly it will pick up some
random noise. Adding a few milliseconds of delay fixes the issue and
shouldn't have any other negative side effects.
3ms seems to be the minimum delay required in my tests, use 5ms instead
just to be sure.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Stephan Gerhold [Wed, 14 Jul 2021 08:56:25 +0000 (10:56 +0200)]
board: dragonboard410c: Fix fastboot
At the moment pressing the volume down key does not actually launch
fastboot. This is because setting "bootdelay" to "-1" actually
disables autoboot and drops to the U-Boot console. It does not execute
the "bootcmd".
The correct value for "bootdelay" here would be "-2", which disables
the delay and key checking and would immediately execute the "bootcmd".
However, even better in this case is using "preboot" to trigger Fastboot.
The advantage is that running "fastboot continue" will actually continue
the autoboot process instead of ending up in the U-Boot shell.
Also make sure to unset "preboot" again immediately in case the user
saves the environment after triggering fastboot.
Cc: Ramon Fried <rfried.dev@gmail.com> Fixes: aa043ee91a47 ("db410c: automatically launch fastboot") Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Stephan Gerhold [Wed, 14 Jul 2021 08:56:24 +0000 (10:56 +0200)]
board: dragonboard410c: Fix PHYS_SDRAM_1_SIZE
The DragonBoard 410c has proprietary firmware from Qualcomm that
reserves 8 MiB of memory for tz/smem/hyp/rmtfs/rfsa from 0x86000000
to 0x86800000. I'm not aware of any ATF (ARM Trusted Firmware) port
for DB410c that would reserve 30 MiB of memory at the end of RAM.
I suspect the comment might have been copied from hikey.h which has
a very similar comment (and which actually does have an ATF port).
Reducing the memory size just prevents U-Boot from using the end of
the RAM, not the reserved region inbetween. Therefore we might as well
display the correct DRAM size (1 GiB) instead of strange 986 MiB.
Fixes: 626f048bbc14 ("board: Add Qualcomm Dragonboard 410C support") Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Stephan Gerhold [Wed, 7 Jul 2021 09:06:02 +0000 (11:06 +0200)]
board: dragonboard410c: Load U-Boot directly without LK
At the moment the U-Boot port for the DragonBoard 410c is designed
to be loaded as an Android boot image after Qualcomm's Little Kernel (LK)
bootloader. This is simple to set up but LK is redundant in this case,
since everything done by LK can be also done directly by U-Boot.
Dropping LK entirely has at least the following advantages:
- Easier installation/board code (no need for Android boot images)
- (Slightly) faster boot
- Boot directly in 64-bit without a round trip to 32-bit for LK
So far this was not possible yet because of unsolved problems:
1. Signing tool: The firmware expects a "signed" ELF image with extra
(Qualcomm-specific) ELF headers, usually used for secure boot.
The DragonBoard 410c does not have secure boot by default but the
extra ELF headers are still required.
2. PSCI bug: There seems to be a bug in the PSCI implementation
(part of the TrustZone/tz firmware) that causes all other CPU cores
to be started in 32-bit mode if LK is missing in the boot chain.
This causes Linux to hang early during boot.
There is a solution for both problems now:
1. qtestsign (https://github.com/msm8916-mainline/qtestsign)
can be used as a "signing" tool for U-Boot and other firmware.
2. A workaround for the "PSCI bug" is to execute the TZ syscall when
entering U-Boot. That way PSCI is made aware of the 64-bit switch
and starts all other CPU cores in 64-bit mode as well.
Simplify the dragonboard410c board by removing all the extra code that
is only used to build an Android boot image that can be loaded by LK.
This allows dropping the custom linker script, special image magic,
as well as most of the special build/installation instructions.
CONFIG_REMAKE_ELF is used to build a new ELF image that has both U-Boot
and the appended DTB combined. The resulting u-boot.elf can then be
passed to the "signing" tool (e.g. qtestsign).
The PSCI workaround is placed in the "boot0" hook that is enabled
with CONFIG_ENABLE_ARM_SOC_BOOT0_HOOK. The extra check for EL1 allows
compatibility with custom firmware that enters U-Boot in EL2 or EL3,
e.g. qhypstub (https://github.com/msm8916-mainline/qhypstub).
As a first step these changes apply only to DragonBoard410c.
Similar changes could likely also work for the DragonBoard 820c.
Note that removing LK wouldn't be possible that easily without a lot of
work already done three years ago by Ramon Fried. A lot of missing
initialization, pinctrl etc was already added back then even though
it was not strictly needed yet.
Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
configs: synquacer: Ignore OsIndications on DeveloperBox
Since we can not set OsIndications from Runtime Services
SetVariables at this moment, it is better to ignore the
OsIndications if there is any capsule file in the
correct place.
configs: synquacer: Use RAW capsule image instead of FIT
Since the recent commit;
commit b891ff18f899 ("efi_loader: Force a single FMP instance per hardware store")
forces a single FMP instances for a storage, we can not
enable both RAW and FIT capsule image support at once.
Since RAW capsule image support is simpler than FIT,
enable RAW capsule image instead of FIT by default.
configs: synquacer: Drop Ext2/4 support by default
Since the U-Boot for the SynQuacer DeveloperBox is designed for
compatible with EDK2 boot, we don't need to support Ext2/4 fs
support by default. Drop it.
board: synquacer: Initialize SCBM SMMU at board_init()
Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.
Move the SMMU initialization code into board support
and call it from board_init().
Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.
In case crypt-based hashing is enabled this will be the default mechanism
that is used. If a user wants to have support for both, the environment
variable `bootstopusesha256` can be set to `true` to allow plain SHA256
based hashing of the password.
Signed-off-by: Steffen Jaeckel <jaeckel-floss@eyet-services.de> Reviewed-by: Simon Glass <sjg@chromium.org>
The key-sequence based unlock mechanisms are sensitive to junk symbols
that could have been sent to stdin and are still waiting to be retrieved.
Enabling this option will read all symbols off stdin before displaying the
autoboot prompt (and starting to read the password from stdin).
Signed-off-by: Steffen Jaeckel <jaeckel-floss@eyet-services.de> Reviewed-by: Simon Glass <sjg@chromium.org>
common: allow disabling of timeout for password entry
In case a user has to enter a complicated password it is sometimes
desireable to give the user more time than the default timeout.
Enabling this feature will disable the timeout entirely in case the user
presses the <Enter> key before entering any other character.
Signed-off-by: Steffen Jaeckel <jaeckel-floss@eyet-services.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Add the basic functionality required to support the standard crypt
format.
The files crypt-sha256.c and crypt-sha512.c originate from libxcrypt and
their formatting is therefor retained.
The integration is done via a crypt_compare() function in crypt.c.
Nandor Han [Thu, 10 Jun 2021 13:56:44 +0000 (16:56 +0300)]
reboot-mode: read the boot mode from GPIOs status
A use case for controlling the boot mode is when the user wants
to control the device boot by pushing a button without needing to
go in user-space.
Add a new backed for reboot mode where GPIOs are used to control the
reboot-mode. The driver is able to scan a predefined list of GPIOs
and return the magic value. Having the modes associated with
the magic value generated based on the GPIO values, allows the
reboot mode uclass to select the proper mode.
Signed-off-by: Nandor Han <nandor.han@vaisala.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Nandor Han [Thu, 10 Jun 2021 13:56:43 +0000 (16:56 +0300)]
reboot-mode: add support for reboot mode control
A new driver uclass is created to handle the reboot mode control.
The new uclass driver is updating an environment variable with the
configured reboot mode. The mode is extracted from a map provided
at initialization time. The map contains a list of modes
and associated ids.
Signed-off-by: Nandor Han <nandor.han@vaisala.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Wed, 14 Jul 2021 07:12:41 +0000 (09:12 +0200)]
net: remove CONFIG_NET_MULTI (again)
CONFIG_NET_MULTI has been removed long time ago by commit 795428fc679f
("net: remove CONFIG_NET_MULTI") but 4 boards were added later which wasn't
found. The patch is removing this reference from 4 boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
The ARM Juno boards can be used as somewhat decent machines to run
off-the-shelf distributions, with USB, SATA, GBit Ethernet and 8GB of
DRAM.
With stable DTs in the board's NOR flash this would work really nicely,
however the default boot command is to fetch a kernel and an initrd from
the on-board NOR flash, which sounds somewhat embedded.
Include the config_distro_bootcmd.h header and define the available
devices (starting with USB, to catch USB installer sticks) to make
distributions and UEFI work out of the box.
The NOR flash kernel functionality is still preserved as the last
resort, should all other methods fail.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Andre Przywara [Sun, 11 Jul 2021 23:07:09 +0000 (00:07 +0100)]
distro_boot: Fix block device after DHCP boot sequence
The generic distro boot sequence iterates over several types of devices,
trying one after another. In doing do, it starts with setting the
"devtype" variable, then uses this later in more generic commands.
Now most (block) device types use a local variable for that, but DHCP
puts the type into the environment, where it shadows any local variables.
As a consequence any boot attempt after bootcmd_dhcp has been run fails:
===========================
VExpress64# run bootcmd_dhcp
...
VExpress64# run bootcmd_sata0
SATA#0:
(3.0 Gbps)
SATA#1:
(No RDY)
Device 0: Model: 16GB SATA Flash Drive ....
... is now current device
Couldn't find partition dhcp 0:1
===========================
This problem typically doesn't show, because DHCP is mostly the last
command to try, but is a problem when this order is different, or when
distro_bootcmd or bootcmd_xxx are run separately or multiple times.
Let bootcmd_dhcp use a local variable, as the other kids do, to make the
order of boot commands irrelevant, and allow repeated calls.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log