fastboot: reinit partition after storing GPT or MBR
In case MMC has MBR system and fastboot writes GPT,
MMC is still recognized as MBR.
Invoke part_init() to purge cached data and update
information about partition table type.
Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com>
Patrick Delaunay [Wed, 27 Jan 2021 13:46:49 +0000 (14:46 +0100)]
fastboot: add command to select the eMMC boot configuration
Add command oem bootbus which executes the command
``mmc bootbus <id> <arg>`` on the current fastboot mmc device
(<i> = CONFIG_FASTBOOT_FLASH_MMC_DEV) to set the eMMC boot
configuration on first update, with
<arg> = boot_bus_width reset_boot_bus_width boot_mode
Patrick Delaunay [Wed, 27 Jan 2021 13:46:48 +0000 (14:46 +0100)]
fastboot: add command to select the default emmc hwpart for boot
Add fastboot command oem partconf which executes the command
``mmc partconf <id> <arg> 0`` on the current <id> mmc device
to configure the eMMC boot partition with
<arg>: boot_ack boot_partition, so the command is:
Split userdata and boot partition support for eMMC update
and correct the description (update is supported).
The new configuration CONFIG_FASTBOOT_MMC_USER_SUPPORT
allows to activate support of userdata partition update,
based on target name=CONFIG_FASTBOOT_MMC_USER_NAME
This patch also removes the unnecessary dependency with
ARCH_MEDIATEK and EFI_PARTITION.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
It is possible to implement fastboot_set_reboot_flag in a generic way
if BCB commands are turned on for a target. Using
bcb_set_reboot_reason allows to do this by simply passing string with
correct reboot reason that should be handled during next boot process.
If BCB are turned off, then bcb_set_reboot_reason would simply return
error, so it won't introduce any new behaviour for such targets.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Current generic implementation of fastboot_set_reboot_flag is somewhat
messy and requires some additional configuration option to be enabled
besides CMD_BCB, so it reverts that implementtion in order to bring a
new cleaner one.
Next commit introduces new generic implementation of
fastboot_set_reboot_flag.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
- introduces some standard sysinfo options as a source, e.g. to read
strapping pins to determine the board revision
- allows the U-Boot version number to be included
- allows the version number to be provided programmatically, e.g. to
support the build system adding information after U-Boot is built
Simon Glass [Fri, 5 Feb 2021 04:17:22 +0000 (21:17 -0700)]
x86: coral: Add sysinfo ops
These ops are missing at present which is not permitted. Add an empty
operation struct.
Note: If the uclass requires operations then the drivers should provide
them. Otherwise, checking for missing operations must be done in every
uclass operation, so it adds to code size.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:21 +0000 (21:17 -0700)]
sysinfo: Move #ifdef so that operations are always defined
At present the struct is not available unless SYSINFO is enabled. This is
annoying since code it is not possible to use compile-time checks like
CONFIG_IS_ENABLED(SYSINFO) with this header.
Fix it by moving the #ifdef.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:20 +0000 (21:17 -0700)]
smbios: Add more options for the BIOS version string
At present the version string is obtained from PLAIN_VERSION. Some boards
may want to configure this using the device tree, since the build system
can more easily insert things there after U-Boot itself is built. Add this
option to the code.
Also in some cases the version needs to be generated programmatically,
such as when it is stored elsewhere in the ROM and must be read first.
To handle this, keep a pointer around so that it can be updated later.
This works by storing the last string in the context, since it is easier
than passing out a little-used extra parameter.
Provide a function to update the version string.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:18 +0000 (21:17 -0700)]
smbios: Drop the eos parameter
We can store this in the context and avoid passing it to each function.
This makes it easier to follow and will also allow keeping track of the
end of the string table (in future patches).
Add an 'eos' field to the context and create a function to set it up.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:17 +0000 (21:17 -0700)]
smbios: Use a struct to keep track of context
At present we pass the ofnode to each function. We also pass the 'eos'
pointer for adding new strings. We don't track the current end of the
string table, so have smbios_string_table_len() to find that.
The code can be made more efficient if it keeps information in a
context struct. This also makes it easier to add more features.
As a first step, switch the ofnode parameter to be a context pointer.
Update smbios_add_prop() at the same time to avoid changing the same
lines of code in consecutive patches.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:13 +0000 (21:17 -0700)]
Makefile: Provide numeric versions
For SMBIOS we want to store the numeric version numbers in the tables. It
does not make sense to parse the strings. Instead, add new #defines with
the version and patchlevel.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Fri, 5 Feb 2021 14:39:31 +0000 (09:39 -0500)]
Merge tag 'ti-v2021.04-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Sync DTS from Linux kernel for all K3 platforms
- Add MMC higher speed nodes for AM65x, J721e, J7200
- Convert Nokia RX-51 to use CONFIG_DM_MMC
- Minor fixes for LEGO MINDSTORMS
Tom Rini [Thu, 4 Feb 2021 22:35:50 +0000 (17:35 -0500)]
Merge tag 'efi-2021-04-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-04-rc2
Bug fixes:
* do not allow creating of files with filenames on FAT file system
* install UEFI System Partition GUID on ESP handle
* in dtbdump.efi test tool use GUID to find ESP handle
Documentation:
* man-page for load command
* describe end of life of plat_auto
The Load File2 protocol exposes a device path with a VenMedia() node. Hence
our implementation of the device path to text protocol should support this
node.
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If dtbdump.efi is loaded from memory when calling LoadImage the loaded
image protocol will not indicate the partition from where it was loaded.
In this case use the EFI system partition for the 'load' and 'save'
commands.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_loader: only check size if EFI_DT_APPLY_FIXUPS
In the implementation of the EFI_DT_FIXUP_PROTOCOL:
* Only check the buffer size when EFI_DT_APPLY_FIXUPS is set.
* In this case the field totalsize of the device-tree may not exceed the
buffer size.
* Install device-tree only if EFI_DT_INSTALL_TABLE is set.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Lokesh Vutla [Mon, 1 Feb 2021 05:56:41 +0000 (11:26 +0530)]
arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot
Sync all J7200 related v5.11-rc6 Linux kernel dts into U-Boot.
MCU R5F nodes are not yet added in Linux kernel yet but were added
in U-Boot. In order to avoid regressions, r5f nodes are kept intact.
These will be added in kernel in future.
Lokesh Vutla [Mon, 1 Feb 2021 05:56:40 +0000 (11:26 +0530)]
arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot
Sync all J721e related v5.11-rc6 Linux kernel dts into U-Boot.
HBMC nodes are not yet added in Linux kernel yet but were added
in U-Boot. In order to avoid any regressions, hbmc nodes are kept
intact. These will be added in kernel in future.
Faiz Abbas [Thu, 4 Feb 2021 09:41:04 +0000 (15:11 +0530)]
arm: dts: k3-am654-base-board: Limit Sd card to High speed modes
There's an issue with the base board in which the power cycle
circuit takes way longer to power down than expected by mmc core.
code. This prevents the card from enumerating in UHS modes.
Disable UHS modes for this board until a new board revision fixes
the issue.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Faiz Abbas [Thu, 4 Feb 2021 09:40:56 +0000 (15:10 +0530)]
arm: dts: k3-am65: Fix mmc nodes
Because of fundamental interface issues in am65x pg1, only the
initial sdhci1 node at 25 MHz was added in the u-boot.dtsi
from which both the base-board.dts and r5-base-board.dts
inherit the node. Move the node out to k3-am65-main.dtsi
where it belongs and add the board specific properties
in base-board.dts and r5-base-board.dts
This ensures dts compatibility with the kernel dts in the
base-board.dts and enables the SD card interface at 50 MHz
and High Speed mode
While we are here, also fix the main_mmc0_pins_default
property to be included and inherit from the base-board.dts
instead of the u-boot.dtsi
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Faiz Abbas [Thu, 4 Feb 2021 09:40:54 +0000 (15:10 +0530)]
mmc: am654_sdhci: Fix HISPD bit configuration in some lower speed modes
According to the AM654x Data Manual[1], the setup timing in lower speed
modes can only be met if the controller uses a falling edge data launch.
To ensure this, the HIGH_SPEED_ENA (HOST_CONTROL[2]) bit should be
cleared in default speed, SD high speed, MMC high speed, SDR12 and SDR25
speed modes.
Use the sdhci writeb callback to implement this condition.
Faiz Abbas [Thu, 4 Feb 2021 09:40:53 +0000 (15:10 +0530)]
mmc: am654_sdhci: Add support for software tuning
With the new SW tuning App note[1], a custom tuning algorithm is
required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
involves running through the 32 possible input tap delay values and
sending the appropriate tuning command (CMD19/21) for each of them
to get a fail or pass result for each of the values. Typically, the
range will have a small contiguous failing window. Considering the
tuning range as a circular buffer, the algorithm then sets a final
tuned value directly opposite to the failing window.
Faiz Abbas [Thu, 4 Feb 2021 09:40:51 +0000 (15:10 +0530)]
mmc: am654_sdhci: Add support for input tap delay
DLL need only be enabled for speed modes and clock frequencies at or
above 50 MHz. For speed modes that don't enable the DLL, we need to
configure a static input delay value. This involves reading an optional
itap-del-sel-* value from the device tree and configuring it for the
appropriate speed mode.
Therefore, move all dll configurations to their own functions and gate it
with 50 MHz speed and a minimum mode. If both these conditions are not
satisfied then configure delay chain modes.
Faiz Abbas [Thu, 4 Feb 2021 09:40:47 +0000 (15:10 +0530)]
mmc: am654_sdhci: Unconditionally switch off DLL in the beginning of ios_post()
There are some speed modes that work without switching the dll on.
Unconditionally switch off the DLL before setting clock frequency to
support this case. The software will automatically enable DLL for speed
modes that require it. This also means the dll_on priv data member is no
longer required.
Suman Anna [Wed, 27 Jan 2021 00:20:56 +0000 (18:20 -0600)]
remoteproc: k3_r5: Sync to upstreamed kernel DT property names
The K3 R5F remoteproc driver in U-Boot was upstreamed prior to the
equivalent remoteproc driver in the Linux kernel. Some of the DT
properties used in U-Boot got upstreamed using different names
in Linux kernel.
The modified property names include the R5F cluster mode configuration
property "lockstep-mode"; and three different individual R5F core config
properties - "atcm-enable", "btcm-enable" and "loczrama". The property
names were updated as follows:
lockstep-mode => ti,cluster-mode
atcm-enable => ti,atcm-enable
btcm-enable => ti,btcm-enable
loczrama => ti,loczrama
Update the K3 R5F remoteproc driver, the corresponding binding, and
all the existing usage in AM65x, J721E and J7200 dts files all at
once to use the new properties and to not break any bisectability.
configs: am65x_evm_a53: Enable config for phandle check while getting sequence number
AM65x SoC has two USB subsystems and their corresponding device tree nodes
have the same name but different path. While allocating sequence numbers
for these device tree nodes using alias, phandles can be used to
distinguish them.
Enable config for phandle check while getting sequence number to
distinguish the USB device tree nodes.
David Lechner [Mon, 11 Jan 2021 19:24:46 +0000 (13:24 -0600)]
configs: legoev3: disable CONFIG_NET
This disables the CONFIG_NET setting for LEGO MINDSTORMS EV3. This board
does not have any built-in networking, so it does not make sense to
enable this feature.
This also fixes the warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: David Lechner <david@lechnology.com>
David Lechner [Mon, 11 Jan 2021 19:24:45 +0000 (13:24 -0600)]
ARM: legoev3: drop bi_arch_number
This drops assigning bi_arch_number on LEGO MINDSTORMS EV3. This board
never had its own unique number and since we are using device tree,
we no longer need to pass an arch number to Linux.
Signed-off-by: David Lechner <david@lechnology.com>
David Lechner [Mon, 11 Jan 2021 19:24:44 +0000 (13:24 -0600)]
ARM: legoev3: set serial# env var
This sets the serial# environmet variable instead of using ATAGs on
LEGO MINDSTORMS EV3.
Also fix some nomenclature while we are touching this code (Bluetooth
address is not the same as MAC address, EEPROM version is not the same
as board version).
Signed-off-by: David Lechner <david@lechnology.com>
Pali Rohár [Sat, 16 Jan 2021 00:04:54 +0000 (01:04 +0100)]
Nokia RX-51: Convert to CONFIG_DM_MMC
Move twl4030_power_mmc_init() from board_mmc_power_init() to misc_init_r()
and disable CONFIG_SYS_MALLOC_F. Otherwise U-Boot cannot initialize MMC.
Also disable CONFIG_CMD_SLEEP CONFIG_DM_DEVICE_REMOVE CONFIG_MMC_VERBOSE to
free some space.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Kory Maincent [Tue, 2 Feb 2021 15:42:29 +0000 (16:42 +0100)]
cmd: pxe_utils: sysboot: Add zboot support to boot x86 Linux kernel image
Add "zboot" command to the list of supported boot in the
label_boot function.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add component tags in the summary] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Kory Maincent [Tue, 2 Feb 2021 15:42:28 +0000 (16:42 +0100)]
cmd: pxe_utils: Replace ifdef by IS_ENABLED
Replace all the macro ifdef by IS_ENABLED.
All of these configs are set in the defconfig files and not in the
include board headers files.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: keep the preprocessor case unchanged] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Kory Maincent [Tue, 2 Feb 2021 15:42:27 +0000 (16:42 +0100)]
command.h: Remove extern from the header
Remove the extern of the header because they are useless.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[bmeng: minor edit on the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Tue, 2 Feb 2021 07:04:47 +0000 (15:04 +0800)]
x86: qemu: Fix broken multi-core boot
Unfortunately the multi-core boot for QEMU x86 has been broken since
commit 77a5e2d3bc61 ("x86: mp_init: Set up the CPU numbers at the start").
In order to support QEMU x86 multi-core boot, the /cpus node must be
bound before any actual fix up in qemu_cpu_fixup(). This adds the
uclass_get() call to ensure this, just like what was done before.
Fixes: 77a5e2d3bc61 ("x86: mp_init: Set up the CPU numbers at the start") Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
The FAT32 File System Specification [1] requires leading and trailing
spaces as well as trailing periods of long names to be ignored.
[1]
Microsoft Extensible Firmware Initiative
FAT32 File System Specification
Version 1.03, December 6, 2000
Microsoft Corporation
https://www.win.tue.nl/~aeb/linux/fs/fat/fatgen103.pdf
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Bin Meng [Sun, 31 Jan 2021 12:36:06 +0000 (20:36 +0800)]
bdinfo: Change to use bdinfo_print_num_ll() where the number could be 64-bit
There are some calls to bdinfo_print_num_l() with parameters that
could be a 64-bit value on a 32-bit system. Change those calls to
use bdinfo_print_num_ll() instead.
Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Sun, 31 Jan 2021 12:36:05 +0000 (20:36 +0800)]
bdinfo: Rename function names to be clearer
At present we have bdinfo_print_num() to print unsigned long numbers.
We also have print_phys_addr() which accept numbers that might be
64-bit on a 32-bit platform.
Bin Meng [Sun, 31 Jan 2021 12:36:04 +0000 (20:36 +0800)]
riscv: Change phys_addr_t and phys_size_t to 64-bit
phys_addr_t and phys_size_t are currently defined as `unsigned long`,
but RV32 supports 34-bit physical address, hence both phys_addr_t and
phys_size_t should be defined to 64-bit using `unsigned long long`.
Bin Meng [Sun, 31 Jan 2021 12:36:03 +0000 (20:36 +0800)]
fdtdec: Cast prior_stage_fdt_address with uintptr_t
At present prior_stage_fdt_address is declared as phys_addr_t. On
a 32-bit platform where phys_addr_t can be 64-bit, assigning its
value to gd->fdt_blob which is a pointer, can cause warnings.
Cast it to uintptr_t before the assignment.
Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Sun, 31 Jan 2021 12:36:02 +0000 (20:36 +0800)]
net: ftmac100: Cast priv->iobase with uintptr_t
priv->iobase was declared as phys_addr_t which is now a 64-bit
address. In a 32-bit build, this causes the following warning
seen when building ftmac100.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Bin Meng [Sun, 31 Jan 2021 12:36:00 +0000 (20:36 +0800)]
serial: sifive: Cast dev_read_addr() with uintptr_t
dev_read_addr() returns fdt_addr_t which is now a 64-bit address.
In a 32-bit build, this causes the following warning seen when
building serial_sifive.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Bin Meng [Sun, 31 Jan 2021 12:35:57 +0000 (20:35 +0800)]
riscv: Adjust board_get_usable_ram_top() for 32-bit
When testing QEMU RISC-V 'virt' machine with a 2 GiB memory
configuration, it was discovered gd->ram_top is assigned to
value zero in setup_dest_addr().
While gd->ram_top should not be declared as type `unsigned long`,
which will be updated in a future patch, the current logic in
board_get_usable_ram_top() can be updated to cover both 64-bit
and 32-bit RISC-V.
Marek Vasut [Sun, 24 Jan 2021 21:32:46 +0000 (14:32 -0700)]
dm: core: Add late driver remove option
Add another flag to the DM core which could be assigned to drivers and
which makes those drivers call their remove callbacks last, just before
booting OS and after all the other drivers finished with their remove
callbacks. This is necessary for things like clock drivers, where the
other drivers might depend on the clock driver in their remove callbacks.
Prime example is the mmc subsystem, which can reconfigure a card from HS
mode to slower modes in the remove callback and for that it needs to
reconfigure the controller clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 24 Jan 2021 21:32:45 +0000 (14:32 -0700)]
dm: core: Avoid partially removing devices
At present if device_remove() decides that the device should not actually
be removed, it still calls the uclass pre_remove() method and powers the
device down.
Simon Glass [Sun, 24 Jan 2021 21:32:44 +0000 (14:32 -0700)]
dm: core: Remove children before advising uclass
At present the uclass pre-remove method is called before the children are
removed. But the children may refused to be removed, in whch case the
uclass is in a tricky situation. At present we handle this by calling
the uclass' post_probe() method. But it seems better to avoid doing
anything with the uclass in this case.
Switch the ordering so that we make sure the children can be removed
before advising the uclass.
Simon Glass [Sun, 24 Jan 2021 21:32:42 +0000 (14:32 -0700)]
dm: Rename DM_FLAG_REMOVE_WITH_PD_ON
This flag has the word 'REMOVE' in it which means it conflicts with
the DM_REMOVE flags. Rename it to DM_FLAG_LEAVE_PD_ON which seems to
indicate its purpose well enough.
Simon Glass [Sun, 24 Jan 2021 21:32:40 +0000 (14:32 -0700)]
smem: Don't use -EPROBE_DEFER
This has no useful meaning in U-Boot. Use -ENOMEM since that appears to
be what has gone wrong in this case. We want to reserve this flag for
internal driver model use.
fs: fat: usage basename in file_fat_write_at, fat_mkdir
This patch involves no functional change. It is just about code
readability.
Both in file_fat_write_at() and fat_mkdir() the incoming file or directory
path are split into two parts: the parent directory and the base name.
In file_fat_write_at() the value of the variable basename is assigned to
the filename parameter and afterwards the variable filename is used instead
of basename. It is more readable to use the variable basename and leave
filename unchanged.
In fat_mkdir() the base name variable is called directory. This is
confusing. Call it basename like in file_fat_write_at(). This allows to
rename parameter new_directory to directory in the implementation of
fat_mkdir() to match the function declaration.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Sun, 31 Jan 2021 08:38:35 +0000 (16:38 +0800)]
azure: Add -E back for the world build script
Commit dd5c954e917b ("travis/gitlab/azure: Use -W to avoid warnings check")
added -W to avoid warnings check, but it mistakenly dropped -E for
the world build script in the azure pipelines.
This caused builds on the azure pipelines fail to report warnings. Let's
add it back.
Fixes: dd5c954e917b ("travis/gitlab/azure: Use -W to avoid warnings check") Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Sun, 31 Jan 2021 03:12:18 +0000 (20:12 -0700)]
test/py: fix runtest wrapper for pytest 6
The implementation of pytest_runtest_protocol() must call
pytest_runtest_logstart() and pytest_runtest_logfinish(). This appears to
be necessary even in pytest 5.2.1 judging by the default version of
pytest_runtest_protocol(), but evidently some form of code reorganization
in pytest only made this have a practical effect in the newer version. I'd
previously been under the impression that 100% of the required work of
pytest_runtest_protocol() was handled by the fact it called
runtestprotocol() as its implementation. However, it appears that custom
implementations do need to do a little more than this.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Ramon Fried [Fri, 29 Jan 2021 16:18:22 +0000 (18:18 +0200)]
MAINTAINERS: Add maintainer to network subsystem
Add myself as co maintainer to network subsystem Acked-by: Tom Rini <trini@konsulko.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Pali Rohár [Wed, 27 Jan 2021 15:29:13 +0000 (16:29 +0100)]
arm: Remove #include <version.h> from armv8/fwcall.c
No version information is used in armv8/fwcall.c therefore do not include
version.h header file. This change prevents recompiling fwcall.o when
SOURCE_DATE_EPOCH changes.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log