Marek Vasut [Wed, 16 Dec 2015 00:32:47 +0000 (01:32 +0100)]
nios2: Enable support for fitImage
The uImage format is legacy for years now, enable support for the
fitImage format, which allows combining multiple files (kernel and
dtb) into a single file, offers better protection of the payload
and so on.
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Marek Vasut [Tue, 15 Dec 2015 02:09:24 +0000 (03:09 +0100)]
nios2: Preconfigure $loadaddr variable
Preset the $loadaddr environment variable to some sane default, let's
say half of the RAM. This variable is where the kernel is loaded using
all sorts of .*load commands, so it's convenient to have it set.
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Marek Vasut [Tue, 15 Dec 2015 02:09:23 +0000 (03:09 +0100)]
nios2: Up the monitor size to 512kiB
The monitor is growing much larger with various additions, like fitImage,
command line completion, UBI etc. Make the monitor area larger so these
features can be safely added.
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Marek Vasut [Tue, 15 Dec 2015 02:09:22 +0000 (03:09 +0100)]
nios2: Calculate the env position from monitor size
Reorder the 10m50 and 3c120 config files such, that the environment
position can be calculated from the monitor size. The environment is
placed right after the monitor. This removes one more ad-hoc variable.
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Nathan Rossi [Tue, 8 Dec 2015 14:44:42 +0000 (00:44 +1000)]
arm: zynq: Update ZYBO config options
Update the ZYBO device tree and enable config options that relate to the
added devices in the device tree.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michal Simek <monstr@monstr.eu> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Nathan Rossi [Tue, 8 Dec 2015 14:44:40 +0000 (00:44 +1000)]
spi: zynq_qspi: Add configuration to disable LQSPI feature
When the Zynq Boot ROM code loads the payload from QSPI it uses the
LQSPI feature of the QSPI device, however it does not clean up its
configuration before handing over to the payload which leaves the device
confgured to by-pass the standard non-linear operating mode.
This ensures the Linear QSPI mode is disabled before re-enabling the
device.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Cc: Jagan Teki <jteki@openedev.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Nathan Rossi [Tue, 24 Nov 2015 09:34:09 +0000 (19:34 +1000)]
ARM: zynq: Add default ps7_init_gpl.c/h for ZYBO
Add ps7_init_gpl.c/h for the ZYBO board. This instance of the ps7_init
is generated by the Vivado 2015.3 tools using the system configuration
provided by Digilent located on their website.
Update the kconfig so that the defconfig is not overrided to use the
custom init ps7_init_gpl target by default.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michal Simek <monstr@monstr.eu> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Stephen Warren [Fri, 13 Nov 2015 20:34:09 +0000 (13:34 -0700)]
usb: kbd: don't use int xfers when polling via ctrl xfers
When CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP is enabled, use a
GET_REPORT control transfer to retrieve the initial state of the
keyboard. This matches the technique used to poll the keyboard state.
This is useful since it eliminates the remaining use of interrupt
transfers from the USB keyboard driver, which allows it to work with
USB HCD that don't support interrupt transfers.
Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Alexey Brodkin [Mon, 14 Dec 2015 14:18:50 +0000 (17:18 +0300)]
usb: add support of generic OHCI devices
This driver is meant to be used with any OHCI-compatible host
controller in case if there's no need for platform-specific
glue such as setup of controller or PHY's power mode via
GPIOs etc.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Simon Glass <sjg@chromium.org> Cc: Marek Vasut <marex@denx.de>
Lukasz Majewski [Thu, 10 Dec 2015 15:32:25 +0000 (16:32 +0100)]
usb: host: ehci: samsung: Move hcor initialization after usb phy setup
With the old order of initialization the hcor pointer has been setup to
the same address as Exynos EHCI base address (0x12110000 instead of
0x12110010).
Such behaviour was caused by reading value of 0 instead of 0x10 from EHCI
HCCPBASE register without doing proper clock initialization before.
To fix this problem hcor initialization has been moved after USB PHY setup.
Now ehci_readl(&ctx->hcd->cr_capbase) returns correct value.
Marek Vasut [Wed, 19 Aug 2015 21:27:26 +0000 (23:27 +0200)]
usb: s3c-otg: Rename USB_GADGET_S3C_UDC_OTG* to USB_GADGET_DWC2_OTG*
The s3c-otg IP block is in fact a DWC2 OTG one, so finally rename the
config option to make it less misleading. No functional change, just
a mechanical change done using the following script:
git grep USB_GADGET_S3C_UDC_OTG | cut -d : -f 1 | sort -u | \
while read line ; do
sed -i "s/USB_GADGET_S3C_UDC_OTG/USB_GADGET_DWC2_OTG/g" $line ;
done
Marek Vasut [Fri, 4 Dec 2015 01:34:46 +0000 (02:34 +0100)]
usb: s3c-otg: Rename sources to dwc2_*c
The driver is actually for the Designware DWC2 controller.
This patch renames the local source files to dwc2_*c and
adjusts the Makefile to use the new names.
Marek Vasut [Fri, 4 Dec 2015 01:32:22 +0000 (02:32 +0100)]
usb: s3c-otg: Rename local headers to dwc2_*h
The driver is actually for the Designware DWC2 controller.
This patch renames the local header files to dwc2_*h and
adjusts the sources to use the new names.
Marek Vasut [Fri, 4 Dec 2015 01:03:45 +0000 (02:03 +0100)]
usb: s3c-otg: Rename s3c_udc_*() functions
The driver is actually for the Designware DWC2 controller.
This patch renames the s3c_ep_*() functions to reflect this.
The function s3c_udc_probe() is a special case and is not
renamed by this patch yet.
Marek Vasut [Fri, 4 Dec 2015 00:44:41 +0000 (01:44 +0100)]
usb: s3c-otg: Rename struct s3c_usbotg_phy to dwc2_usbotg_phy
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_usbotg_phy to struct dwc2_usbotg_phy
to make things more obvious and clear.
Marek Vasut [Fri, 4 Dec 2015 00:36:36 +0000 (01:36 +0100)]
usb: s3c-otg: Split private bits from s3c_udc.h
Most of the functions are local to the s3c_udc driver, remove them
from the s3c_udc.h header to stop those bits from propagating all
over the place. Instead, move all the private stuff into new private
s3c_udc_otg_priv.h header.
Marek Vasut [Fri, 4 Dec 2015 00:11:45 +0000 (01:11 +0100)]
usb: s3c-otg: Rename struct s3c_usbotg_reg to dwc2_usbotg_reg
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_usbotg_reg to struct dwc2_usbotg_reg
to make things more obvious and clear.
Shaohui Xie [Fri, 4 Dec 2015 02:22:03 +0000 (10:22 +0800)]
net: fm: disables unused FM1-DTSEC1 MAC node in DTS
We don't disable unused FM1-DTSEC1 MAC node in FMAN v2 since it is
used by MDIO. For FMAN v3, MDIO uses dedicated controller, so we
can disable unused FM1-DTSEC1 MAC node to avoid being probed in
Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
[York Sun: revised commit message] Reviewed-by: York Sun <yorksun@freescale.com>
Mingkai Hu [Mon, 7 Dec 2015 08:58:54 +0000 (16:58 +0800)]
armv8/ls1043a: Implement workaround for PEX erratum A009929
Consecutive write transactions from core to PCI express outbound
path hangs after 25 to 30 transactions depending on core freq.
This erratum enable the mbist clock through COP register setting.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Stuart Yoder [Thu, 3 Dec 2015 21:14:04 +0000 (15:14 -0600)]
driver: net: fsl-mc: remove MC firmware version check
The MC version numbers provide no meaningful information
about binary interface compatibility, so remove the
check which refuses to start the MC unless a specific
version is found.
Version checking is supposed to be done at the individual
object level, and individual drivers are responsible
for their own version checking.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Acked-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Unify the code for doing read/write into single function, since the
code for both the read and write is almost identical. This again
trims down the code duplication.
----------------------->8--------------------
where the same one routine is utilized for both EEPROM writing and
reading. The only difference was supposed to be a "read" flag which
in both cases was set with 1 somehow.
That lead to a missing delay in case of writing which lead to write
failure (in my case no data was written).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Acked-by: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Cc: Heiko Schocher <hs@denx.de>
Tang Yuantian [Wed, 9 Dec 2015 07:32:18 +0000 (15:32 +0800)]
armv8: Add sata support on Layerscape ARMv8 board
Freescale ARM-based Layerscape contains a SATA controller
which comply with the serial ATA 3.0 specification and the
AHCI 1.3 specification.
This patch adds SATA feature on ls2080aqds, ls2080ardb and
ls1043aqds boards.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Aneesh Bansal [Tue, 8 Dec 2015 08:24:30 +0000 (13:54 +0530)]
drivers/crypto/fsl: fix endianness issue in RNG
For Setting and clearing the bits in SEC Block registers
sec_clrbits32() and sec_setbits32() are used which work as
per endianness of CAAM block.
So these must be used with SEC register address as argument.
If the value is read in a local variable, then the functions
will not behave correctly where endianness of CAAM and core is
different.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> CC: Alex Porosanu <alexandru.porosanu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Aneesh Bansal [Tue, 8 Dec 2015 08:24:29 +0000 (13:54 +0530)]
armv8/ls1043ardb: add SECURE BOOT target for NOR
LS1043ARDB Secure Boot Target from NOR has been added.
- Configs defined to enable esbc_validate.
- ESBC Address in header is made 64 bit.
- SMMU is re-configured in Bypass mode.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Aneesh Bansal [Tue, 8 Dec 2015 08:24:28 +0000 (13:54 +0530)]
include/linux: move typdef for uintptr_t
uintptr_t which is a typdef for unsigned long is needed for creating
pointers (32 or 64 bit depending on Core) from 32 bit variables
storing the address.
If a 32 bit variable (u32) is typecasted to a pointer (void *),
compiler gives a warning in case size of pointer on the core is 64 bit.
The typdef has been moved from include/compiler.h to include/linux/types.h
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Alexander Stein [Wed, 4 Nov 2015 08:19:10 +0000 (09:19 +0100)]
fsl_qspi: Pet the watchdog while reading/writing
When reading a large blob. e.g. a linux kernel (several MiBs) a watchdog
timeout might occur meanwhile. So pet the watchdog while operating on
the flash.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Reviewed-by: York Sun <yorksun@freescale.com>
York Sun [Mon, 7 Dec 2015 19:08:58 +0000 (11:08 -0800)]
armv8: fsl-layerscale: Rewrite reserving memory for MC and debug server
MC and debug server are not board-specific. Move reserving memory to SoC
file, using the new board_reserve_ram_top function. Reduce debug server
memory by 2MB to make room for secure memory.
In the system with MC and debug server, the top of u-boot memory
is not the end of memory. PRAM is not used for this reservation.
York Sun [Mon, 7 Dec 2015 19:05:29 +0000 (11:05 -0800)]
common: Rewrite hiding the end of memory
As the name may be confusing, the CONFIG_SYS_MEM_TOP_HIDE reserves
some memory from the end of ram, tracked by gd->ram_size. It is not
always the top of u-boot visible memory. Rewrite the macro with a
weak function to provide flexibility for complex calcuation. Legacy
use of this macro is still supported.
Signed-off-by: York Sun <yorksun@freescale.com> Reviewed-by: Simon Glass <sjg@chromium.org>
York Sun [Fri, 4 Dec 2015 19:57:08 +0000 (11:57 -0800)]
armv8: fsl-layerscape: Make DDR non secure in MMU tables
DDR has been set as secure in MMU tables. Non-secure master such
as SDHC DMA cannot access data correctly. Mixing secure and non-
secure MMU entries requirs the MMU tables themselves in secure
memory. This patch moves MMU tables into a secure DDR area.
Early MMU tables are changed to set DDR as non-secure. A new
table is added into final MMU tables so secure memory can have
2MB granuality.
gd->secure_ram tracks the location of this secure memory. For
ARMv8 SoCs, the RAM base is not zero and RAM is divided into several
banks. gd->secure_ram needs to be maintained before using. This
maintenance is board-specific, depending on the SoC and memory
bank of the secure memory falls into.
York Sun [Fri, 4 Dec 2015 19:57:07 +0000 (11:57 -0800)]
Reserve secure memory
Secure memory is at the end of memory, separated and reserved
from OS, tracked by gd->secure_ram. Secure memory can host
MMU tables, security monitor, etc. This is different from PRAM
used to reserve private memory. PRAM offers memory at the top
of u-boot memory, not necessarily the real end of memory for
systems with very large DDR. Using the end of memory simplifies
MMU setup and avoid memory fragmentation.
"bdinfo" command shows gd->secure_ram value if this memory is
marked as secured.
Tom Rini [Mon, 14 Dec 2015 16:08:38 +0000 (11:08 -0500)]
armv7: omap-common: Rework SPL board_mmc_init()
Since the changes in a1e56cf the way that we had board_mmc_init()
structured for OMAP parts (so that we always report device 0) are no
longer functional. For now, make the case of booting from the second
device initialize both devices (we have no devices that only have the
second device as MMC). A further rework and consolidation of the
functions should be done at a later date.
Tested on Beaglebone Black (SD and eMMC boot).
Reported-by: Vagrant Cascadian <vagrant@debian.org> Signed-off-by: Tom Rini <trini@konsulko.com>
Eric Nelson [Sat, 5 Dec 2015 19:32:28 +0000 (12:32 -0700)]
spl: mmc: use block device number, not hard-coded 0
In order to support boot from multiple devices through board_boot_order,
it's necessary to use the block number of a device.
The use of a hard-coded 0 for the device number also creates a need
to re-order block devices for use in SPL like this:
http://git.denx.de/?p=u-boot.git;a=blob;f=board/freescale/mx6slevk/mx6slevk.c;hb=HEAD#l195
huang lin [Mon, 7 Dec 2015 03:08:57 +0000 (11:08 +0800)]
rockchip: Add basic support for kylin board
kylin board use rk3036 SOC, 512M sdram, 8G emmc.
This add some basic files required to allow the board
to output serial message and can run command(mmc info etc).
Signed-off-by: Lin Huang <hl@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sat, 28 Nov 2015 13:04:42 +0000 (08:04 -0500)]
qbman_portal.c: Update BUG_ON() call in qbman_swp_mc_submit
With gcc-5.x we get a warning about the ambiguity of BUG_ON(!a != b) and
becomes BUG_ON((!a) != b). In this case reading of the function leads to
us wanting to rewrite this as BUG_ON(a != b).
Cc: Prabhakar Kushwaha <prabhakar@freescale.com> Cc: Geoff Thorpe <Geoff.Thorpe@freescale.com> Cc: Haiying Wang <Haiying.Wang@freescale.com> Cc: Roy Pledge <Roy.Pledge@freescale.com> Cc: York Sun <yorksun@freescale.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <yorksun@freescale.com>
Tom Rini [Sat, 28 Nov 2015 13:04:41 +0000 (08:04 -0500)]
fsl_*_serdes.c: Modify memset call in serdes_init
GCC 5.x does not like sizeof(array_variable) and errors out. Change these
calls to be instead sizeof(u8) (as that's what serdes_prtcl_map is) *
SERDES_PRCTL_COUNT (the number of array elements).
Cc: York Sun <yorksun@freescale.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shaohui Xie [Mon, 23 Nov 2015 07:23:48 +0000 (15:23 +0800)]
armv8/ls1043ardb: Add support for >2GB memory
This patch also expose the complete DDR region(s) to Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shaohui Xie [Tue, 10 Nov 2015 11:20:16 +0000 (19:20 +0800)]
freescale: fman: make sure phy-handle property is big endian
When creating phy-handle property, an unsigned int value is created by
fdt_create_phandle, and memcpy is used to get the value, since DTS is
big endian, the value cannot be used directly on little endian SoCs,
it should be converted by cpu_to_fdt32.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Stephen Warren [Wed, 9 Dec 2015 16:48:04 +0000 (09:48 -0700)]
part: fix "part list ... -bootable varname" to use hex
Unfortunately U-Boot assumes that almost all numbers are in hex, including
partition numbers passed to e.g. "load". So, the command "part list mmc 0
-bootable devplist" should use hex when writing partition numbers into
$devplist, so they'll be correctly interpreted.
Change-Id: I9a70b19749643876baadb45efbc3decaef8bfee2 Fixes: 0798d6fd4191 ("part: Add support for list filtering on bootable partitions") Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
projects / u-boot.git / log