Alexey Brodkin [Tue, 13 Jan 2015 15:49:01 +0000 (18:49 +0300)]
Kconfig: move CONFIG_SYS_CLK_FREQ to Kconfig
It makes sense to specify CONFIG_SYS_CLK_FREQ in "configs/xx_defconfig"
instead of "include/configs/xxx.h" because then header will be reusable
across boards with different CPU clocks.
Also this nice to have an ability for end user to tune this value
himself via "menuconfig".
For now I'm only applying this change to all ARC configs because
otherwise scope of change will be huge.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Tom Rini <trini@ti.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Hans de Goede <hdegoede@redhat.com>
cc: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
Masahiro Yamada [Thu, 8 Jan 2015 10:23:35 +0000 (19:23 +0900)]
spl: spl_nor: surround Linux-load code with #ifdef CONFIG_SPL_OS_BOOT
If CONFIG_SPL_NOR_SUPPORT is defined, spl_nor_load_image() requires
spl_start_uboot(), CONFIG_SYS_OS_BASE, CONFIG_SYS_SPL_ARGS_ADDR,
CONFIG_SYS_FDT_BASE to be defined even if users just want to run
U-Boot, not Linux. This is inconvenient.
This patch is following the codying style of common/spl/spl_nand.c.
Simon Glass [Tue, 2 Dec 2014 20:17:37 +0000 (13:17 -0700)]
bootm: Factor out common parts of image decompression code
Adjust the code so that the error reporting can all be done at the end,
and is the same for each decompression method. Try to detect when
decompression fails due to lack of space. Keep the behaviour of
resetting on failure even though there should be no memory corruption
now.
Simon Glass [Tue, 2 Dec 2014 20:17:31 +0000 (13:17 -0700)]
sandbox: Correct ordering of 'sb save' commands
Prior to commit d455d87 there was an inconsistency between the position of
the 'address' parameter in 'sb load' and 'sb save'. This was corrected but
it broke some tests. Fix the tests and also the help for 'sb save'.
Simon Glass [Tue, 2 Dec 2014 20:17:30 +0000 (13:17 -0700)]
bootm: Move compression progress/error messages into a function
This code is repeated in several places, and does not detect a common
fault where the image is too large. Move it into its own function and
provide a more helpful messages in this case, for compression schemes
which support this.
Simon Glass [Tue, 2 Dec 2014 20:17:29 +0000 (13:17 -0700)]
lzma: fix buffer bound check error further
Commit 4d3b8a0d fixed a problem with lzma decompress where it would
run out of bytes to decompress. The algorithm needs to know how many
uncompressed bytes it is expected to produce.
However, the fix introduced a potential buffer overrun, and causes
the compression test to fail (test_compression command in sandbox).
The correct fix seems to be to use the minimum of the expected number
of uncompressed bytes and the amount of output space available. That
way things work normally when there is enough space, and return an
error (without overrunning available space) when there is not.
Signed-off-by: Antonios Vamporakis <ant@area128.com> CC: Kees Cook <keescook@chromium.org> CC: Simon Glass <sjg@chromium.org> CC: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> CC: Luka Perkov <luka@openwrt.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Wed, 14 Jan 2015 03:35:24 +0000 (12:35 +0900)]
README.scrapyard: fill commit and date fields
This commit was generated by the following command:
scripts/fill_scrapyard.py
The commit-ID of CPCIISER4 removal has been fixed by hand because
the board was removed by commit 370572601027 (ppc4xx: remove CPCIISER4
board), but it was added to README.scrapyard by commit 9a4018e09a2f
(ppc4xx: remove DP405 board).
Hans de Goede [Sun, 11 Jan 2015 18:33:35 +0000 (19:33 +0100)]
sunxi: usbc: Add support for usb-vbus0 controller by axp drivebus pin
The axp221 / axp223's N_VBUSEN pin can be configured as an output rather
then an input, and this is used on some boards to control usb-vbus0, add
support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 11 Jan 2015 18:58:03 +0000 (19:58 +0100)]
sunxi: axp221: Add support for controlling the drivebus pin
The axp221 / axp223's N_VBUSEN pin can be configured as an output rather
then an input, add axp_drivebus_enable() and _disable() functions to set
the pin in output mode and control it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 11 Jan 2015 18:43:56 +0000 (19:43 +0100)]
sunxi: axp221: Protect axp221_init against multiple calls
The voltage setting code knows it needs to call axp221_init before calling
the various voltage setting functions.
But users of axp utility functions like axp221_get_sid() do not know this,
so the utility functions always call axp221_init() to ensure that the
p2wi / rsb setup magic has been done.
Since doing this repeatedly is quite expensive, add a check to axp221_init
so that it only does the initialization once.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Chen-Yu Tsai [Mon, 12 Jan 2015 10:02:12 +0000 (18:02 +0800)]
sunxi: Hummingbird_A31_defconfig: Enable VGA output through external DAC
The Hummingbird A31 uses an external DAC connected to the LCD0 outputs
for the on board VGA output. The DAC has a power control that's toggled
by GPIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Mon, 12 Jan 2015 10:02:10 +0000 (18:02 +0800)]
sunxi: video: Allow external DACs for VGA on platforms without TV encoders
Using an external DAC for VGA output was available on sun5i. Since
some other SoCs don't have a builtin TV encoder, but might have
use for a VGA output, enable the option for the platforms that
don't have TV encoders.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This allows to always have a complete log on the VGA/HDMI/LCD console.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
console: Use pre-console buffer to get complete log on all consoles
Currently the pre-console buffer can accumulate early log messages
and flush them to the serial console as soon as it becomes available.
This patch just adds one more pre-console buffer flushing point and
does all the same for the other consoles too. This is particularly
useful for the vga/hdmi/lcd console, where we can see all the older
messages now (except for the log messages from SPL).
Naturally, we don't want to get an extra copy of the log messages
on the serial console again at the second flushing point, so the
serial console has to be explicitly filtered out.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Jan Kiszka [Wed, 31 Dec 2014 12:46:42 +0000 (13:46 +0100)]
sun7i: Move psci_arch_init close to text_end
"adr rX, text_end" only works if the label is close. Adding further code
to the other functions will prevent this. So move the containing
function close to label. No functional change.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Jan Kiszka [Wed, 31 Dec 2014 12:46:40 +0000 (13:46 +0100)]
sun7i: Add support for taking CPUs offline via PSCI
Based on the original version by Marc Zyngier. It adds a psci_cpu_off
implementation for the A20 SoC. The mechanism works by first preparing
the calling CPU to go offline (disable and flush cache, disable SMP),
then requesting CPU 0 to pull the plug. The request is sent as FIQ on
SGI15.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Zoltan HERPAI [Tue, 6 Jan 2015 00:09:18 +0000 (01:09 +0100)]
sunxi: add Linksprite pcDuino v1/v2 support
Add support for a sun4i board built by Linksprite. This addition covers
both v1 and v2 versions. As the board has been working with 408MHz memory
setting in the u-boot-sunxi branch, and has been proven to be running stable
during my tests as well, a respective new DRAM config file is added as well.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 28 Dec 2014 08:13:21 +0000 (09:13 +0100)]
sunxi: video: Add a hpd_delay parameter to configure hpd delay
In some extreme cases it may be necessary to wait 1.5 seconds or more for a hpd
signal to show up (and be able to read edid info), but we do not want to
penalize all headless boots with an extra second boot delay, so add a hpd_delay
parameter which can be set through the video-mode env. variable.
While at it raise the default from 300ms to 500ms as 300 may very well be too
low in many cases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 24 Dec 2014 18:50:11 +0000 (19:50 +0100)]
sunxi: video: Use sunxi_lcdc_get_clk_delay to calculate tcon1 delay
Use sunxi_lcdc_get_clk_delay to calculate tcon1 delay instead of hardcoding
it to 30. We will still end up using 30 for most modes, but for e.g. 800x600
this makes a (small) difference.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Having both a sunxi_display.enabled variable and
sunxi_display.monitor == sunxi_monitor_none duplicates state, use
sunxi_display.monitor = sunxi_monitor_none when ever we do not have a display.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Enable VGA output on the A13-OLinuXino and A13-OLinuXinoM now that we've
support for it.
Also add LCD timing and gpio info for the Olimex 7" LCD module. We can safely
put this in the default config on this boards, since by default we will always
use VGA, and the LCD timing info will only get used if the user explicitly
sets monitor=lcd in the video-mode env. variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 24 Dec 2014 15:08:30 +0000 (16:08 +0100)]
sunxi: sunxi-common.h: Reduce bootm_size to take the framebuffer into account
Before video output support can be enabled on the A13-OLinuXinoM, bootm_size
must first be reduced to take into account that the framebuffer is shaved of
the top of the DRAM. For other boards this is not an issue since bootm was set
to 256M and all boards have at least 512M except for the A13-OLinuXinoM.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 21 Dec 2014 15:27:45 +0000 (16:27 +0100)]
sunxi: video: Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1
Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1, this is a
preparation patch for adding lcd support.
While at it also swap the divider search order, searching from low to
high, as the comment above the code says we should do. In cases where there
are multiple solutions this will result in picking a lower pll clock and
divider, which is more stable and saves power.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 21 Dec 2014 13:49:34 +0000 (14:49 +0100)]
sunxi: video: Prepare for lcd support
Refactor sunxi_mode_set into a bunch of helpers, and make it do a switch
case on sunxi_display.monitor to decide what to do.
Also rename sunxi_lcdc_mode_set to sunxi_lcdc_tcon1_mode_set, as it sets the
timings for tcon1, and for lcd support we need a similar function operating
on tcon0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a sunxi_monitor enum and parse the monitor option string into this enum
once, rather then doing strcmp-s on it in various places. This also adds
checking for it being a valid value.
This also adds new "none" and "lcd" values in preparation for lcd support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 24 Dec 2014 18:34:38 +0000 (19:34 +0100)]
sunxi: gpio: Add support for gpio pins on the AXP209 pmic
Some boards use GPIO-s on the pmic, one example of this is the A13-OLinuXino
board, which uses gpio0 of the axp209 for the lcd-power signal.
This commit adds support for gpio pins on the AXP209 pmic, the sunxi_gpio.c
changes are universal, adding gpio support for the other AXP pmics (when
necessary) should be a matter of adding the necessary axp_gpio_foo functions
to their resp. drivers, and add "#define AXP_GPIO" to their header file.
Note this commit only adds support for the non device-model version of the
gpio code, patches for adding support to the device-model version are very
welcome.
The string representation for these gpio-s is AXP0-#, the 0 in the AXP0 prefix
is there in case we need to support gpio-s on more then 1 pmic in the future.
At least A80 boards have 2 pmics, and we may end up needing to support gpio-s
on both.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 20 Dec 2014 12:51:16 +0000 (13:51 +0100)]
sunxi: video: Set input sync enable
Add a write to the "unknown" (*) register to enable auto input sync, when
initially adding sunxi hdmi output support this magic write from the android
kernel code was missed, causing lcdc -> hdmi encoder sync problems.
With this write added, we can drop the modesetting retries and the extra
delays added to work around these sync problems.
With the retries dropped there also is no need to 0 all the enable flags at
the beginning of the modeset, as they are initialized to 0 already by
engines_init.
*) "unknown" is the actual name of this register in the android kernel sources
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
Hans de Goede [Sat, 20 Dec 2014 14:15:23 +0000 (15:15 +0100)]
sunxi: video: Give hotplug-detect (hpd) signal some time to show up
When using a hdmi powered hdmi to vga dongle, and cold booting a sunxi
device, the hpd detect code would not see the dongle (until a warm reboot),
because the dongle needs some time to boot.
Testing has shown that this dongle needs 213ms to respond on a cold boot,
so wait up to 300ms for a hpd signal to show up before giving up.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
Hans de Goede [Sat, 20 Dec 2014 12:38:06 +0000 (13:38 +0100)]
sunxi: video: Add hdmi support
So far we've been programming the hdmi-encoder to send out dvi data over the
hdmi connector. This works well for most devices, including hdmi devices, but
not all devices accept dvi data on a hdmi input.
Add support for sending proper hdmi data over the hdmi output found on most
sunxi boards. This can be turned on by adding monitor=hdmi as option to the
video-mode env. variable.
A follow up patch will determine whether to send dvi or hdmi automatically when
EDID is used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
Hans de Goede [Fri, 19 Dec 2014 15:05:12 +0000 (16:05 +0100)]
sunxi: video: Add DDC & EDID support
Add DDC & EDID support and use it to automatically select the native mode of
the attached monitor. This can be disabled by adding edid=0 as option
to the video-mode env. variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
Hans de Goede [Fri, 19 Dec 2014 14:13:57 +0000 (15:13 +0100)]
sunxi: video: Add hpd option
Allow the user to specify hpd=0 as option in the video-mode env. variable,
if hpd is set to 0 then the hdmi output will be brought up even if no cable
is connected.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
Hans de Goede [Fri, 19 Dec 2014 12:22:47 +0000 (13:22 +0100)]
videomodes: Add video_get_ctfb_res_modes helper function
Add a video_get_ctfb_res_modes() helper function, which uses
video_get_video_mode() to parse the 'video-mode' environment variable and then
looks up the matching mode in res_mode_init and returns the matching mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
Hans de Goede [Fri, 19 Dec 2014 10:11:52 +0000 (11:11 +0100)]
videomodes: Add (vesa) standard timings
The timings for the modes defined in videomodes.c differ (significantly)
from vesa standard timings for these modes.
This commit adds a version with the proper std timings for these modes,
since I do not want to cause regressions, boards which want to use the standard
timings need to define CONFIG_VIDEO_STD_TIMINGS to get the new correct timings.
Since there is no std timing for 960x720 this commit uses the timing used
by the nvidia video drivers for 960x720, which uses a standard pixelclock
of 74.25 MHz rather then the weird 76.335... clock used by the old modes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
Hans de Goede [Fri, 19 Dec 2014 09:38:49 +0000 (10:38 +0100)]
videomodes: Add pixelclock_khz and refresh fields to ctfb_res_modes
Add pixelclock_khz and refresh fields to ctfb_res_modes:
1) pixelclocks are usually referred to in hz, not picoseconds, and e.g
pll-s are also typically programmed in hz, not ps. Converting between the
2 leads to rounding differences, add a pixelclock_khz field to directly
store the *exact* pixelclock for a mode, so that drivers do not need to
resort to rounding tricks to try and guess the exact pixelclock;
2) The video-mode environment variable, as parsed by video_get_video_mode
also contains the vertical refresh rate, add a refresh field, so that
the refresh-rate can be matched when parsing the video-mode environment
variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
Hans de Goede [Wed, 31 Dec 2014 10:30:26 +0000 (11:30 +0100)]
sun7i: Add new Bananapro board / defconfig
Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 27 Dec 2014 16:56:59 +0000 (17:56 +0100)]
sunxi: Fix PLL1 running at half speed on sun8i
PLL1 on sun6i / sun8i also has a p factor which divides the clock by
2^p (to the power p). On sun6i the p factor is ignored, but on sun8i it is
used and we were setting it to 1, resulting in the CPU running at 504 MHz
instead of 1008 MHz, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
sunxi: Fix buggy sun6i/sun8i DRAM size detection logic
After reboot, reset or even short power off, DRAM typically retains
the old stale data for some period of time (for this type of memory,
the bits of data are stored in slowly discharging capacitors).
The current sun6i/sun8i DRAM size detection logic, which is
inherited from the Allwinner code, relies on using a large magic
signature with the hope that it is unique enough and unlikely to
ever accidentally match this leftover garbage data in RAM. But
this approach is inherently unsafe, as can be demonstrated using
the following test program:
/***** A testcase for reproducing the problem ******/
void main(int argc, char *argv[])
{
size_t size, i;
uint32_t *buf;
/* Allocate the buffer */
if (argc < 2 || !(size = (size_t)atoi(argv[1]) * 1048576) ||
!(buf = malloc(size))) {
printf("Need buffer size in MiB as a cmdline argument\n");
exit(1);
}
/* Fill it with the Allwinner DRAM "magic" values */
for (i = 0; i < size / 4; i++)
buf[i] = 0xaa55aa55 + ((uintptr_t)&buf[i] / 4) % 64;
/* Try to reboot */
system("reboot");
/* And wait */
for (;;) {}
}
/***************************************************/
If this test program is run on the device (giving it a large
chunk of memory), then the DRAM size detection logic in u-boot
gets confused after reboot and fails to initialize DRAM properly.
A better approach is not to rely on luck and abstain from making
any assumptions about the properties of the leftover garbage
data in RAM. Instead just use a more reliable code for testing
whether two different addresses refer to the same memory location.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch uses the same DRAM settings as in the pre-installed
Android firmware. The LCD display is supported too.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch uses the same ZQ and DRAM clock settings as in the
pre-installed Android firmware.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi: Fix CONFIG_UART0_PORT_F build and add it to menuconfig
The CONFIG_UART0_PORT_F option has been supported since
http://git.denx.de/?p=u-boot.git;a=commit;h=ff2b47f6a9cc1025
This option is primarily useful only for low level u-boot debugging
on tablets, where normal UART0 is difficult to access and requires
device disassembly and/or soldering.
This patch now allows it to be selected from menuconfig. A dependency on
SPL_FEL is added because u-boot does not support booting from NAND yet
and also booting from SD card is impossible when a MicroSD breakout board
is plugged into the SD slot.
Additionally a compilation problem is fixed:
common/spl/built-in.o: In function `spl_mmc_load_image':
/tmp/u-boot-sunxi/common/spl/spl_mmc.c:94: undefined reference to `mmc_initialize'
/tmp/u-boot-sunxi/common/spl/spl_mmc.c:96: undefined reference to `find_mmc_device'
/tmp/u-boot-sunxi/common/spl/spl_mmc.c:104: undefined reference to `mmc_init'
scripts/Makefile.spl:206: recipe for target 'spl/u-boot-spl' failed
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sat, 20 Dec 2014 11:25:14 +0000 (12:25 +0100)]
sun8i: Ippo_q8h_v5_defconfig: Enable SPL support
Now that we've sun8i dram-init support we can enable the SPL for sun8i boards.
While at it also replace CONFIG_DEFAULT_DEVICE_TREE with CONFIG_FDTFILE,
the former is for u-boot's own fdt usage, which we do not use (yet), the later
specifies the fdt to pass to the kernel, which is the one we want.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Mon, 8 Dec 2014 12:58:53 +0000 (13:58 +0100)]
sunxi: Fill memory before comparing it when doing dram init on sun6i
The sun8i boot0 code fills the DRAM with a "random" pattern before comparing
it at different offsets to do columns, etc. detection. The sun6i boot0 code
does not do it, instead relying on the memory contents being random enough
to begin with for the memcmp to properly detect the wrap-around address, iow
it is working purely by chance. Since our sun6i dram code was modelled after
the boot0 code it contained the same issue.
This commit fixes this by filling the memory with a unique, distinct pattern.
The new mctl_mem_fill function this introduces is added as an inline helper
in dram.h, so that it can be shared with the sun8i dram code.
While at it move mctl_mem_matches to dram.h for re-use in sun8i too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Mon, 8 Dec 2014 12:38:21 +0000 (13:38 +0100)]
sunxi: Move await_completion dram helper to dram.h
The await_completion helper is already copy pasted between the sun4i and sun6i
dram code, and we need it for sun8i too, so lets make it an inline helper in
dram.h, rather then adding yet another copy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 7 Dec 2014 20:09:31 +0000 (21:09 +0100)]
sun6i: clock_set_pll5: Calculate k and m rather then hardcoding them
Our old hardcoded k and m values are based on PLL5 being configured in steps
of 48 MHz, which is correct for sun6i where the DRAM PLL runs at twice the
DRAM CLK, which is usually configured in 24 MHz step. But on the A23 (sun8i)
the PLL5 runs at half the DRAM CLK, so we require 12 MHz steps.
This commit adjusts clock_set_pll5 to automatically select the best k and m
depending on the requested clk rate.
Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 13 Dec 2014 13:02:38 +0000 (14:02 +0100)]
sunxi: axp221: Explicitly turn off unused voltages
Explicitly turn off unused voltages, rather then leaving them as is. Likewise
explictly enabled the dcdc convertors, rather then assuming they are already
enabled at boot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 13 Dec 2014 13:12:06 +0000 (14:12 +0100)]
sunxi: axp221: Make dcdc1 voltage configurable
The dcdc1 voltage is typically used as generic 3.3V IO voltage for things like
GPIO-s, sdcard interfaces, etc. On most boards this is undervolted to 3.0V to
safe battery, but not on all, make it configurable so that we can use the
same settings as the original firmware on all boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 13 Dec 2014 11:40:45 +0000 (12:40 +0100)]
sunxi: axp221: Add Kconfig help and sane defaults for typical ldo usage
Some of the ldo-s of the axp221 are used in the same way on most boards, add
comments to the Kconfig help text to reflect this, and give them defaults
matching their typical usage.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 29 Nov 2014 22:54:25 +0000 (23:54 +0100)]
sunxi: axp221: Add axp223 support
The axp223 appears to be the same as the axp221, except that it uses the
rsb to communicate rather then the p2wi. At least all the registers we use
are 100% the same.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 29 Nov 2014 12:38:35 +0000 (13:38 +0100)]
sunxi: Add support for the rsb (Reduced Serial Bus)
sun8i (A23) introduces a new bus for communicating with the pmic, the rsb,
the rsb is also used to communicate with the pmic on the A80, and is
documented in the A80 user manual.
This commit adds support for this based on the rsb driver from the allwinner
u-boot sources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Axel Lin [Sat, 20 Dec 2014 03:41:25 +0000 (11:41 +0800)]
mmc: sunxi: Fix misuse of gpio_direction_input()
It does not make sense to make gpio_direction_input() return the gpio input
status. The return value of gpio_direction_input() is inconsistent if
CONFIG_DM_GPIO is defined.
And we don't need to call gpio_direction_input() int sunxi_mmc_getcd().
Just init the gpio once in mmc_resource_init() is enough.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Chen-Yu Tsai [Tue, 9 Dec 2014 08:56:53 +0000 (16:56 +0800)]
sun6i: Add new board Merrii Hummingbird A31
The Merrii Hummingbird A31 is a A31 based development board with 1G
RAM, 8G NAND, AP6210 WiFi+BT, gigabit ethernet, USB OTG, 2 USB 2.0
ports connected to a USB hub chip, HDMI, VGA, TV and stereo in/out.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
projects / u-boot.git / log