Bryan Brattlof [Fri, 29 Dec 2023 17:47:14 +0000 (11:47 -0600)]
arm: dts: k3-am654: remove duplicate wkup_i2c0
With the Linux and U-Boot board dtb files unified, we now have a
duplicate wkup_i2c0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:47:13 +0000 (11:47 -0600)]
arm: dts: k3-am654: remove duplicate sdhci1 pinmux node
With the Linux and U-Boot board dtb files unified, we now have a
duplicate sdhci1 pinmux node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:47:12 +0000 (11:47 -0600)]
arm: dts: k3-am654: remove duplicate sdhci0 pinmux node
With the Linux and U-Boot board dtb files unified, we now have
a duplicate sdhci0 pinmux node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:47:11 +0000 (11:47 -0600)]
arm: dts: k3-am654: remove duplicate main_uart0
With the Linux and U-Boot board dtb files unified, we now have a
duplicate main_uart0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:47:10 +0000 (11:47 -0600)]
arm: dts: k3-am654: remove duplicate mcu_uart0 node
With the Linux and U-Boot board dtb files unified we now have a
duplicate mcu_uart0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:47:09 +0000 (11:47 -0600)]
arm: dts: k3-am654: add needed regs to udmap nodes
Ethernet is one of a few IPs in U-Boot that depend on DMA to operate.
However there are a few missing registers ranges in the udmap nodes
need to properly setup DMA for the am65x.
A fix has been added to the Linux kernel[0] to add these ranges however
they have not made it to a Linux tag. To keep DMA operational until the
next DT sync from Linux, add these ranges to the *-u-boot.dtsi with a
note for our future selves.
[0] https://lore.kernel.org/r/
20231213135138.929517-2-vigneshr@ti.com
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:47:08 +0000 (11:47 -0600)]
arm: dts: k3-am654: remove duplicate mcu_udmap
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mcu_udmap node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:47:07 +0000 (11:47 -0600)]
arm: dts: k3-am654: remove duplicate mcu_ringacc
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mcu_ringacc node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:47:06 +0000 (11:47 -0600)]
arm: dts: k3-am654: remove duplicate timer
timer1 is really just the mcu_timer0 node redefined for the WKUP SPL.
Remove the timer1 and replace it with the mcu_timer0 from the Linux
device tree we imported into U-Boot.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:47:05 +0000 (11:47 -0600)]
arm: dts: k3-am654: remove duplicate wkup_uart0
With the Linux and U-Boot board files unified, we now have a duplicate
wkup_uart0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:47:04 +0000 (11:47 -0600)]
arm: dts: k3-am654: remove duplicate vtt_supply
With the Linux and U-Boot board dtb files unified we now have a
duplicate vtt_supply node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:47:03 +0000 (11:47 -0600)]
arm: dts: k3-am654: include a53 board dtb for r5 build
To make things as organized as possible, start from the Linux board dtbs
and apply all properties needed for U-Boot in our *-u-boot.dtsi file for
the MAIN SPL and U-Boot builds.
We can then include these files for the WKUP SPL build making further
edits to the needed properties and nodes for the WKUP SPL bootloader's
view of the am65x.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:47:02 +0000 (11:47 -0600)]
arm: dts: k3-am654: copy bootph properties to a53 dts
In order to unify the R5 board dtb file with the Linux board dtb file,
we will need to copy all bootph-pre-ram properties to the *-u-boot.dtsi
overlay.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:47:01 +0000 (11:47 -0600)]
arm: dts: k3-am654: pull in dtb update from Linux
Pull in dtb updates for the am654 base board from v6.7-rc1 of Linux
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:47:00 +0000 (11:47 -0600)]
arm: dts: k3-am654-r5: Merge board file and U-Boot overlay
The R5 board file for U-Boot should be the same as the board file copied
from Linux with a few alterations to work with the R5's view of the SoC.
First we need to unify the R5 board file and it's U-Boot overlay before
we can unify the Linux board file with this one.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:46:59 +0000 (11:46 -0600)]
configs: am65x_evm_a53: disable CONSOLE_MUX
We do not have a need to share a single console with the evaluation
board and disabling this option reduces the complexity of configuring
the consoles. Disable CONSOLE_MUX
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Bryan Brattlof [Fri, 29 Dec 2023 17:46:58 +0000 (11:46 -0600)]
configs: am65x_evm_r5: enable driver for fixed regulators
Some of the regulators we need to successfully boot are fixed
regulators. Enable the driver to properly probe them.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Mark Kettenis [Sun, 24 Dec 2023 18:12:55 +0000 (19:12 +0100)]
arm: apple: Disable SMBIOS again
Apple machines do not have memory below 4G. Since U-Boot does
not support the SMBIOS 3 header structures this means we can't
support SMBIOS on these machines. Unfortunately the refactoring
of the SMBIOS code this cycle accidentally enabled it again.
Fixes: 53fab13a7b1 ("efi: Use the installed SMBIOS tables")
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jim Liu [Tue, 26 Dec 2023 02:00:06 +0000 (10:00 +0800)]
spi: npcm_pspi: Fix the wrong clock divider calculation
Fix the wrong clock divider calculation.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Tom Rini [Wed, 20 Dec 2023 19:14:12 +0000 (14:14 -0500)]
Merge tag 'u-boot-imx-master-
20231220' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
- Make DRAM stable on i.MX8MP DHCOM SoM by using FPWM mode and updating
the DRAM timing
- Fix display artifacts when booting Linux on i.MX8M Mini/Plus eDM SBC
Marek Vasut [Sat, 16 Dec 2023 18:07:52 +0000 (19:07 +0100)]
get_maintainer.pl: Add --git to look up CCed in git history
Add the --git parameter, else recent contributors are left out of the CC list.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Baruch Siach [Mon, 18 Dec 2023 07:37:53 +0000 (09:37 +0200)]
net: fix NetConsole documentation reference
Fixes: d0253f7e5ca1 ("doc: move README.NetConsole to HTML documentation")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Marek Vasut [Wed, 13 Dec 2023 21:11:13 +0000 (22:11 +0100)]
net: wget: Support non-default HTTP port
Currently the wget command is hard wired to HTTP port 80. This is
inconvenient, as it is extremely easy to start trivial HTTP server
as an unprivileged user using e.g. python http module to serve the
files, but such a server has to run on one of the higher ports:
"
$ python3 -m http.server -d $(pwd) 8080
"
Make it possible to configure HTTP server port the same way it is
possible to configure TFTP server port, using environment variable
'httpdstp' (similar to 'tftpdstp'). Retain port 80 as the default
fallback port. This way, users can start their own trivial server
and conveniently download whatever files they need into U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Emanuele Ghidoli [Tue, 19 Dec 2023 08:25:33 +0000 (09:25 +0100)]
arm: dts: k3-am625-verdin: fix DDRSS configuration
The current DDR subsystem configuration occasionally results in write failures,
impacting memory stability, on Verdin AM62 Solo 512MB WB IT 0072 SKU.
This commit addresses the issue by adjusting Drive Pull-Up/Down and
Write Latency to improve the eye diagram and ensure reliable write operations.
This configuration is shared with all Verdin AM62 SoM and
it does not introduce regressions.
Configurations changes from previous / default values:
- Drive Pull-Up/Down from 40 to 34.3 Ohm
- Write Latency from 8 to 10
- ODTLon / ODTLoff latency from 0 / 0 to 4 / 20 nCK
- VREF control range 1 at 27 %
- tFAW from 30 to 40 ns
Configuration is output from SysConfig [1] web tool, currently at version
1.18.1+3343 (DDR SubSystem v9.10).
[1] https://dev.ti.com/sysconfig
Fixes: 7d1a10659f5b ("board: toradex: add verdin am62 support")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Peter Robinson [Wed, 22 Nov 2023 22:57:07 +0000 (22:57 +0000)]
doc: Remove README.sha1 file
The contents of README.sha1 only refer to process around verification
of the pcs440ep board firmware in flash. The device was removed in
commit
242836a893ae ("powerpc: ppc4xx: remove pcs440ep support") in
2015 so this readme isn't really relevant anymore so can be removed.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Mon, 18 Dec 2023 18:02:14 +0000 (19:02 +0100)]
ARM: dts: imx: Power off display output on Data Modul i.MX8M Mini/Plus eDM SBC
Turn display connector power off on boot and reboot to prevent any
bogus start up sequence of any panel potentially attached to the
display connector.
Signed-off-by: Marek Vasut <marex@denx.de>
Tom Rini [Mon, 18 Dec 2023 12:49:45 +0000 (07:49 -0500)]
Prepare v2024.01-rc5
Signed-off-by: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 16 Dec 2023 05:42:29 +0000 (06:42 +0100)]
ARM: imx: Update DRAM timings with inline ECC on DH i.MX8MP DHCOM SoM
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB and for 2 GiB device the available DRAM size
becomes 1.8 GiB.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 16 Dec 2023 05:42:28 +0000 (06:42 +0100)]
ARM: imx: Force DRAM regulators into FPWM mode on DH i.MX8MP DHCOM SoM
In case the Buck5 and Buck6 regulators which supply DRAM Vdd1 and Vdd2/Vddq
respectively operate in automatic PWM/PFM mode, the DRAM EDAC detects more
correctable errors than if the regulators operate in forced PWM only mode.
Force DRAM regulators to forced PWM mode only to stop tempting the DRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Tom Rini [Fri, 15 Dec 2023 22:48:52 +0000 (17:48 -0500)]
Merge tag 'clk-2024.01-rc5' of https://source.denx.de/u-boot/custodians/u-boot-clk
clock changes for u-boot/master
This has some clock fixes which should go in before the release. It's a bit
late in the cycle, but most of these have tests to go along with them.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Yang Xiwen [Fri, 15 Dec 2023 20:21:11 +0000 (04:21 +0800)]
test: dm: clk_ccf: fix building error
Fix unused variable error produced by building tests
Fixes: d3061824 (test: dm: clk_ccf: test ccf_clk_ops)
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20231216-b4-fix_build-v1-1-b8e79c94744f@outlook.com
Yang Xiwen [Fri, 15 Dec 2023 18:28:52 +0000 (02:28 +0800)]
test: dm: clk_ccf: test ccf_clk_ops
Assign ccf_clk_ops to .ops of clk_ccf driver so that it can act as an
clk provider. Also add "#clock-cells=<1>" to its device tree node.
Add "i2c_root" to clk_test in the device tree and driver for testing.
Get "i2c_root" clock in CCF unit tests and add tests for it.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20231111-enable_count-v3-2-08a821892fa9@outlook.com
Igor Prusov [Tue, 5 Dec 2023 23:23:34 +0000 (02:23 +0300)]
dm: test: clk: Add test for ccf clk_set_rate()
Add a simple test case which sets clock rate to its current value.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20231205232334.2931-3-ivprusov@salutedevices.com
Igor Prusov [Tue, 5 Dec 2023 23:23:33 +0000 (02:23 +0300)]
clk: Check that composite clock's div has set_rate()
It's possible for composite clocks to have a divider that does not
implement set_rate() operation. For example, sandbox_clk_composite()
registers composite clock with a divider that only has get_rate().
Currently clk_composite_set_rate() only checks thate rate_ops are
present, so for sandbox it will cause NULL dereference during
clk_set_rate().
This patch adds rate_ops->set_rate check tp clk_composite_set_rate().
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20231205232334.2931-2-ivprusov@salutedevices.com
Yang Xiwen [Sat, 18 Nov 2023 22:10:06 +0000 (06:10 +0800)]
clk: get correct ops for clk_enable() and clk_disable()
assign clk_dev_ops(clkp->dev) to ops to ensure correct clk operations
are called on clocks.
This fixes the incorrect enable_count issue as described in [1].
[1]: https://lore.kernel.org/all/SEZPR06MB695927A6DEEEF8489A06897396A7A@SEZPR06MB6959.apcprd06.prod.outlook.com/
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20231111-enable_count-v2-2-20e3728600b5@outlook.com
Yang Xiwen [Fri, 10 Nov 2023 19:19:52 +0000 (03:19 +0800)]
clk: check parent_name in clk_register to avoid confusing log_error() output
For some gate clocks and fixed clocks without a parent, calling
clk_register will print an useless error message indicating that parent
is missing. Fix that by gaurding log_xxx() with an if-statement.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Suggested-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230807-clk-fix-v2-1-0b688e21fb4e@outlook.com
Tom Rini [Fri, 15 Dec 2023 13:22:20 +0000 (08:22 -0500)]
Merge tag 'u-boot-imx-
20231214' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
- Fix for i.MX8M Plus eDM SBC DDR timings with inline ECC
- Switch to FPWM mode on Data Modul i.MX8M Plus eDM SBC so that DRAM
EDAC detects more correctable errors
- Fix for imx8mp-venice board DDR initialization
Tim Harvey [Thu, 14 Dec 2023 16:22:27 +0000 (08:22 -0800)]
imx8mp-venice: update DRAM config for 2000MHz
The imx8mp venice boards can support 2000Mhz DRAM.
Update the DRAM config to support this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Thu, 14 Dec 2023 16:22:26 +0000 (08:22 -0800)]
imx8mp-venice: fix DRAM bus configuration
The DRAM configuration for the 1GB and 4GB imx8mp venice boards had a
bus mapping issue (channel A and B swapped) which creates an invalid
deskewing configuration during training causing the DRAM to not be able
to run at its full bus speed.
Update the various config structures to resolve this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Thu, 14 Dec 2023 16:22:25 +0000 (08:22 -0800)]
board: gateworks: venice: remove extra file
Remove lpddr4_timing_imx8mm_512mb.c mistakenly committed
Fixes: a1c711046b0d "(board: gateworks: venice: add imx8mm-gw7903 support)"
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Marek Vasut [Thu, 7 Dec 2023 17:50:32 +0000 (18:50 +0100)]
ARM: imx: Update DRAM timings with inline ECC on Data Modul i.MX8M Plus eDM SBC
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Marek Vasut [Thu, 7 Dec 2023 17:50:31 +0000 (18:50 +0100)]
ARM: imx: Force DRAM regulators into FPWM mode on Data Modul i.MX8M Plus eDM SBC
In case the Buck5 and Buck6 regulators which supply DRAM Vdd1 and Vdd2/Vddq
respectively operate in automatic PWM/PFM mode, the DRAM EDAC detects more
correctable errors than if the regulators operate in forced PWM only mode.
Force DRAM regulators to forced PWM mode only to stop tempting the DRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Marek Vasut [Sat, 2 Dec 2023 01:58:28 +0000 (02:58 +0100)]
ARM: imx: Enable CAAM on DH i.MX8M Plus DHCOM
Enable CAAM in U-Boot to make crypto available early in the boot process.
This has a side-effect that in case an older kernel version contains a
broken CAAM initialization timeout code, initialization in bootloader
will help that old kernel version function correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Marek Vasut [Sat, 2 Dec 2023 01:55:06 +0000 (02:55 +0100)]
ARM: imx: Enable CAAM on Data Modul i.MX8M Mini/Plus eDM SBC
Enable CAAM in U-Boot to make crypto available early in the boot process.
This has a side-effect that in case an older kernel version contains a
broken CAAM initialization timeout code, initialization in bootloader
will help that old kernel version function correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Marek Vasut [Sat, 2 Dec 2023 01:48:40 +0000 (02:48 +0100)]
ddr: imx: Add 3600 MTps rate support
Add PLL settings for DDR 3600 MTps . This is very similar to 3200 MTps
PLL setting, except the divider is not 9 but 8 .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Marek Vasut [Sat, 2 Dec 2023 01:48:00 +0000 (02:48 +0100)]
ddr: imx: Handle 3734 in addition to 3733 and 3732 MTps rates
The new MX8M DDR tool 3.31 now generates a programming file which uses
data rate 3734 instead of 3733 or 3732 . Handle another rounding option .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Marek Vasut [Sun, 5 Nov 2023 00:04:32 +0000 (01:04 +0100)]
arm64: imx8mp: Inhibit DTC warning on DH i.MX8MP DHCOM rev.100 DTO
Inhibit DTC warning in imx8mp-dhcom-pdk3-overlay-rev100.dts:
"
arch/arm/dts/imx8mp-dhcom-pdk3-overlay-rev100.dtbo: Warning (reg_format): /fragment@0/__overlay__:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
arch/arm/dts/imx8mp-dhcom-pdk3-overlay-rev100.dtbo: Warning (avoid_default_addr_size): /fragment@0/__overlay__: Relying on default #address-cells value
arch/arm/dts/imx8mp-dhcom-pdk3-overlay-rev100.dtbo: Warning (avoid_default_addr_size): /fragment@0/__overlay__: Relying on default #size-cells value
"
The DTO overwrites the 'reg' property of an ethernet PHY and is only
used on specific combination of old prototype SoM and old prototype
PDK3 carrier board, which had incorrectly placed pull resistor, which
made the PHY change its MDIO address in that specific combination and
which is already fixed on production hardware.
The DTO is implemented in this simple manner because if it contained a
full MDIO bus node reference to define #address-cells and #size-cells,
it would also require a full new copy of the PHY node, i.e.
ethernet-phy@5 { ... reg = <5>; ... }, to avoid DTC warnings about
mismatch between node unit and reg value. The node unit in SoM DT is
ethernet-phy@7 { ... }; .
This simpler approach avoids unnecessary duplication without adverse
side effects.
Reported-by: Fabio Estevam <festevam@denx.de>
Reported-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Tom Rini [Wed, 13 Dec 2023 14:57:28 +0000 (09:57 -0500)]
Merge branch '2023-12-13-assorted-minor-fixes'
- A few MAINTAINERS updates and Kconfig wording fixes
Shantur Rathore [Fri, 24 Nov 2023 12:04:31 +0000 (12:04 +0000)]
maintainers: rk3399: remove maintainer
Remove Akash Gajjar <akash@openedev.com> from
MAINTAINERS as email is bouncing.
Signed-off-by: Shantur Rathore <i@shantur.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Peter Robinson [Tue, 5 Dec 2023 09:12:22 +0000 (09:12 +0000)]
maintainers: bcmns3: remove maintainer
Remove Bharat Gooty as a maintainer as his mail is
bouncing.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Moritz Fischer [Wed, 22 Nov 2023 16:21:14 +0000 (16:21 +0000)]
MAINTAINERS: Fix ARCH_APPLE file paths
Fixes a filepath in MAINTAINERS file that wasn't updated when
renaming the files to match the new SoC name.
Fixes: a4bd5e4120d6 ('arm: apple: Change SoC name from "m1" into "apple"')
Signed-off-by: Moritz Fischer <moritzf@google.com>
Alexander Gendin [Mon, 20 Nov 2023 20:21:51 +0000 (20:21 +0000)]
drivers: misc: Kconfig: Fix SPL_FS_LOADER prompt
Both FS_LOADER and SPL_FS_LOADER have the same menu prompt.
To avoid confusion, make prompt for SPL_FS_LOADER different.
Signed-off-by: Alexander Gendin <agendin@matrox.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Mon, 20 Nov 2023 20:17:23 +0000 (15:17 -0500)]
lib/Kconfig: Correct typo about SYSINFO_SMBIOS in help message
The correct symbol to enable to have SMBIOS populate fields based on the
device tree is SYSINFO_SMBIOS and not SMBIOS_SYSINFO.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Tue, 12 Dec 2023 21:32:30 +0000 (16:32 -0500)]
Merge tag 'u-boot-imx-
20231212' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
- Fix emmc detection on colibri_imx7
- Fix DDR configuration on tqma6 to improve Ethernet performance
- Fix aliases and chosen nodes indentation on imx7s-warp
- Convert pico-imx6ul to DM_SERIAL
- Convert pico-pi-imx7d to watchdog driver model to fix 'reset' command
- Select CONFIG_NET_RANDOM_ETHADDR on imx8mp_evk to fix networking on
older boards
- Add USBH_EN gpio hog to fix USB host interface not working on some
Apalis Toradex carrier boards with Apalis iMX8 SoM
- Add PCI fixup for GW73xx-F+
- Fix broken EEPROM read on imx8mn-var-som
Marcel Ziswiler [Tue, 12 Dec 2023 11:28:15 +0000 (08:28 -0300)]
board: colibri_imx7: fix emmc detection
Later versions of Colibri iMX7D V1.1B modules use a "new" SoC fusing. The
difference lies in whether we enable the boot ROM to use the eMMC reset
signal. Depending on the SoC fuse, the boot ROM configures this pin as a
GPIO output to drive the reset signal. Our eMMC vs NAND detection
currently only sets that signal to a GPIO without explicitly setting any
direction. Previously, by default, it was set as an input. As the boot ROM
now configures it as an output, we receive a value of zero instead of one,
indicating the absence of the pull-up on eMMC modules.
To fix this, set the SION bit, allowing the reading back of the value
even if it is configured as an output by the boot ROM. It's important to
note that with the new SoC fusing, we now read back what the boot ROM
drives rather than the real value caused by the pull-up resistor. However,
if it were ever driven low, the eMMC would permanently be reset.
In addition, remove hard-coded variant in the eMMC build case as since the
commit
0c39564d0281 ("toradex: colibri_imx7: Enable nand/emmc detection
and set boot variant") will anyways always get overridden by the detection
routing in board code.
Fixes: 0c39564d ("toradex: colibri_imx7: Enable nand/emmc detection and set boot variant")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Miquel Raynal [Fri, 17 Nov 2023 15:00:44 +0000 (16:00 +0100)]
tqma6: Fix DDR configuration
Initially investigating a Linux network issue causing a lot of drop and
poor network performances on a custom system based on a TQMA6A module
(based on an iMX6Q), [1st link below].
I eventually correlated my observations with a contention at the NIC
level when in concurrency with the graphics pipeline. Troubleshooting
this in the kernel lead to disabling DMA bursts accesses made by the IPU
in order to avoid triggering the QoS at the interconnect level, reducing
from 50 to 10% the drop rate on eth0, [2nd link below]. The solution
worked on my setup but not on others, which still suffered from
abnormally high drop rates even with this "fix".
After looking a while into TQ Systems BSP I figured out a number of
differences in recent U-Boot out-of-tree patches they had in their
repository [3rd link]. Parsing the differences one after the other lead
me to this final solution.
The reset pad of the DDR controller was apparently misconfigured, Bit
18-19 picturing the "DDR select field". The current value b11 is
reserved. The only defined value as of version 6 of the iMX6Q manual was
b00 "DDR3 and LPDDR2 mode". In practice no register difference has been
spotted after changing this configuration but all issues tracked thus
far just vanished. All previous fixes have been proven irrelevant. Just
clearing this field solved all our network issues and the drop rate as
measured by iperf3 felt back to 0%.
Link: https://lore.kernel.org/netdev/20231012193410.3d1812cf@xps-13/
Link: https://lists.freedesktop.org/archives/dri-devel/2023-October/428251.html
Link: https://github.com/tq-systems/u-boot-tqmaxx/commit/15eb6abbefbf6916c28467b85485911dad3da6bc
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Mon, 6 Nov 2023 16:33:22 +0000 (13:33 -0300)]
imx7s-warp-u-boot: Fix aliases and chosen nodes indentation
The aliases and chosen nodes are currently indented using spaces.
Fix them to use the standard tab indentation.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Fabio Estevam [Sat, 4 Nov 2023 21:52:41 +0000 (18:52 -0300)]
pico-pi-imx6ul: Connvert to DM_SERIAL
The conversion to DM_SERIAL is mandatory, so select this option.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Fabio Estevam [Thu, 26 Oct 2023 21:01:53 +0000 (18:01 -0300)]
pico-pi-imx7d: Convert to watchdog driver model
Commit
68dcbdd594d4 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset
Signed-off-by: Fabio Estevam <festevam@denx.de>
Fabio Estevam [Thu, 26 Oct 2023 12:16:36 +0000 (09:16 -0300)]
imx8mp_evk: Select CONFIG_NET_RANDOM_ETHADDR
On an early revision of the imx8mp-evk that I have access to,
the MAC addresses fuses are not programmed, causing failure to bring
the Ethernet interfaces.
Fix this problema by selecting CONFIG_NET_RANDOM_ETHADDR so that
random MAC addresses are assigned and the Ethernet ports become
functional out of the box.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Andrejs Cainikovs [Tue, 12 Dec 2023 12:27:25 +0000 (09:27 -0300)]
apalis-imx8: add USBH_EN gpio hog
USB host interface is not working on some Apalis Toradex carrier
boards with Apalis iMX8 SoM. This is due to USBH_EN pin, which
powers USB peripherals, having a strong pull-down on some boards,
and a weak pull-down on the others. This USBH_EN pin is left
unconfigured, which means it is in its default state at cold boot:
input with a strong pull-up. As a result, carrier boards with a
weak pull-down have this signal high enough to trigger power
delivery to USB peripherals, and opposite - boards with strong
pull-down on USBH_EN have this signal below the threshold needed
to trigger USB power delivery.
This change configures the USBH_EN pin as gpio hog, fixing this
issue for all Apalis carrier boards regardless of pull-down
resistor value.
Also, update apalis-imx8_defconfig via savedefconfig.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Tim Harvey [Wed, 18 Oct 2023 18:33:06 +0000 (11:33 -0700)]
board: gateworks: venice: add fixup for GW73xx-F+
GW73xx-F board revision switched back to the original PCIe switch due to
part availability.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Hugo Villeneuve [Tue, 17 Oct 2023 20:58:15 +0000 (16:58 -0400)]
arm: dts: imx8mn-var-som: Fix broken EEPROM read
On branch WIP/17Oct2023, the EEPROM can no longer be read:
U-Boot 2023.10-latest (Oct 17 2023 - 15:53:43 -0400)
CPU: Freescale i.MX8MNano Quad rev1.0 at 1200 MHz
Reset cause: POR
Model: Variscite VAR-SOM-MX8MN Symphony evaluation board
var_read_som_eeprom: uclass_get_device_by_of_offset() failed: -19
initcall failed at call
000000004022207c (err=-19)
Convert EEPROM-related properties to bootph-all so that the EEPROM can
also be read outside of SPL.
Fixes: 9e644284ab81 ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Tom Rini [Sat, 9 Dec 2023 19:52:46 +0000 (14:52 -0500)]
test/py: Disable error E0611 in two cases for pylint
Recently pylint has started to complain about:
No name 'fs_helper' in module 'tests' (no-name-in-module)
Due to:
from tests import fs_helper
However, we have:
test/py/tests/fs_helper.py
And since we do not want to add a dummy test/py/tests/__init__.py to
silence this warning we instead just disable it as needed.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 9 Dec 2023 19:35:44 +0000 (14:35 -0500)]
Merge https://source.denx.de/u-boot/custodians/u-boot-riscv
- StarFive: Add StarFive watchdog driver
- VisionFive2: Support device tree overlay for VisionFive2 board
- Andes: Fix PLIC-SW setting
- RISC-V: Fix NVMe support by implying NVME_PCI for QEMU
- RISC-V: Fix binman for 64 bit format load address
Tom Rini [Sat, 9 Dec 2023 18:16:14 +0000 (13:16 -0500)]
Merge patch series "bootflow: bootmeth_efi: Fix network efi boot."
To quote the author:
Currently bootmeth_efi crashes while doing a network (dhcp) boot.
This patch series fixes issues and both network and disk boot works.
# Do not modify or remove the line above.
# Everything below it will be ignored.
#
# Please enter a commit message to explain why this merge is necessary,
# especially if it merges an updated upstream into a topic branch.
#
# An empty message aborts the commit.
Shantur Rathore [Sun, 19 Nov 2023 16:55:01 +0000 (16:55 +0000)]
bootflow: bootmeth_efi: don't free buffer
bootmeth_efi doesn't allocate any buffer to load efi in any case.
enable static buffer flag for all cases.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shantur Rathore <i@shantur.com>
Shantur Rathore [Sun, 19 Nov 2023 16:55:00 +0000 (16:55 +0000)]
bootflow: bootmeth_efi: Handle fdt not available.
While booting with efi, if fdt isn't available externally,
just use the built-in one.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shantur Rathore <i@shantur.com>
Shantur Rathore [Sun, 19 Nov 2023 16:54:59 +0000 (16:54 +0000)]
bootflow: bootmeth_efi: set bflow->fname from bootfile name
We need to set boot->fname before calling efi_set_bootdev
otherwise this crashes as bflow->fname is null.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shantur Rathore <i@shantur.com>
Shantur Rathore [Sun, 19 Nov 2023 16:54:58 +0000 (16:54 +0000)]
bootflow: bootmeth_efi: Set bootp_arch as hex
bootmeth_efi sets up bootp_arch which is read later in bootp.c
Currently bootp_arch is being set as integer string and being
read in bootp.c as hex, this sends incorrect arch value to dhcp server
which in return sends wrong file for network boot.
For ARM64 UEFI Arch value is 0xb (11), here we set environment as 11
and later is read as 0x11 and 17 is sent to dhcp server.
Setting it as hex string fixes the problem.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shantur Rathore <i@shantur.com>
Janne Grunau [Fri, 1 Dec 2023 07:12:33 +0000 (08:12 +0100)]
arm: apple: t602x: Add missing MMIO regions to memmap
The memory maps for Apple's M2 Pro/Max/Ultra left MMIO space out which
was not used by any driver at the time. The display out exposed as
simple-framebuffer use a power-domain controlled by a device in an
unmapped region.
Add a map covering this region as well as another MMIO region in the
range 0x4'0000'0000 - 0x5'0000'0000. The added regions cover all MMIO
annotated in Apple's device tree in this range.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tom Rini [Sat, 9 Dec 2023 03:00:24 +0000 (22:00 -0500)]
Merge tag 'u-boot-amlogic-
20231207' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Add missing DM_USB_GADGET to amlogic boards
Tom Rini [Sat, 9 Dec 2023 03:00:01 +0000 (22:00 -0500)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
The first four patches are actual fixes. The last three patches add
support for the apparently popular OrangePi Zero 3 board: multiple
people seem to be champing at the bit, so I'd rather give them
something real instead of people using random trees they found on the
Internet. It's actually mostly the new defconfig file anyway, so the
chances for regressions are very slim.
Tom Rini [Sat, 9 Dec 2023 00:03:03 +0000 (19:03 -0500)]
Merge tag 'efi-2024-01-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2024-01-rc5
Documentation:
* Update and correct support notes on clang
* sandbox: Fix VPL instructions
UEFI:
* Fix a bug in DisconnectController
* Provide better error messages for missing CONFIG_EFI_CAPSULE_ESL_FILE
* Create EFI memory reservations when booting via ACPI
* Make ACPI tables accessible in EFI app
Neil Armstrong [Wed, 6 Dec 2023 09:04:21 +0000 (10:04 +0100)]
configs: meson: enable missing DM_USB_GADGET
Since commit
b96640cbfb ("ARM: meson: g12a: switch dwc2 otg to DM")
and commit
e327e2affd ("ARM: meson: switch AXG & GX dwc2 otg to DM")
Amlogic boards now requires DM_USB_GADGET to have USB Gadget to work.
Add it to the boards configs as returned by:
$ grep -L DM_USB_GADGET $(grep -l CONFIG_USB_GADGET $(grep -l MESON configs/*))
Fixes: b96640cbfb ("ARM: meson: g12a: switch dwc2 otg to DM")
Fixes: e327e2affd ("ARM: meson: switch AXG & GX dwc2 otg to DM")
Link: https://lore.kernel.org/r/20231206-u-boot-m2s-fix-usb-gadget-v1-1-1c4c66cd10f3@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Andre Przywara [Wed, 18 Oct 2023 00:06:52 +0000 (01:06 +0100)]
sunxi: H616: Add OrangePi Zero 3 board support
The OrangePi Zero 3 is a small development board featuring the Allwinner
H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI
connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for
which was recently added to U-Boot.
Add a defconfig file selecting the right drivers and DRAM options.
Since the .dts file was synced from the Linux kernel repo already, we
just need to add one line to the Makefile to actually build the .dtb.
The DRAM parameters were derived from the values found in the BSP DRAM
drivers on the SPI NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Tested-by: Bob McChesney <bob@electricworry.net>
Tested-by: Stephen Graf <stephen.graf@gmail.com>
Andre Przywara [Tue, 17 Oct 2023 16:08:52 +0000 (17:08 +0100)]
sunxi: H616: remove default AXP305 selection
The original H616 devices released about three years ago were typically
paired with an X-Powers AXP305 PMIC. Newer devices uses the smaller
AXP313, and there seem to be far more systems with this PMIC around now.
Remove the default AXP305 selection for the H616 SoC from the Kconfig,
and move the PMIC selection into the board defconfig files instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Andre Przywara [Mon, 13 Nov 2023 01:16:48 +0000 (01:16 +0000)]
mtd: spi-nor: Add support for zBIT ZB25VQ128
Add support for the zBIT ZB25VQ128 (128M-bit) SPI NOR flash memory chip,
as used on the Xunlong Orange Pi Zero 3 board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Chukun Pan [Sun, 29 Oct 2023 07:40:09 +0000 (15:40 +0800)]
sunxi: dts: arm64: update emac for Orange Pi Zero 3
The current emac setting is not suitable for Orange Pi Zero 3,
move it back to Orange Pi Zero 2 DT. Also update phy mode and
delay values for emac on Orange Pi Zero 3.
With these changes, Ethernet now looks stable.
Fixes: 95c3b0635ea4 ("sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Stephen Graf [Fri, 1 Dec 2023 18:50:39 +0000 (10:50 -0800)]
sunxi: correct documentation for SPI flashing
The mtd_debug write does not work in this context. The flashcp command does
work, provides both the erase and write functions and with the verbose
option gives good feedback.
Signed-off-by: Stephen Graf <stephen.graf@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Wed, 13 Jul 2022 15:27:57 +0000 (16:27 +0100)]
sunxi: h616: (really) lower SPL stack address to avoid BROM data
When using the USB OTG FEL mode on the Allwinner H616, the BootROM
stores some data at the end of SRAM C. This is also the location where
we place the initial SPL stack, so it will overwrite this data.
We still need the BROM code after running the SPL, so should leave that
area alone.
Interestingly this does not seem to have an adverse effect, I guess on
the "way out" (when we return to FEL after the SPL has run), this data
is not needed by the BROM, for just the trailing end of the USB operation.
However this is still wrong, and we should not clobber BROM data.
Lower the SPL stack address to be situated right below the swap buffers
we use in sunxi-fel: that should be out of the way of everyone else.
This obsoletes a previous commit (
eb53e7743c8f) with the same name:
that one was changing the address in an *unused* macro in sunxi_common.h,
so the previous patch didn't have any effect at all.
Fixes: eb53e7743c8f ("sunxi: h616: lower SPL stack address to avoid BROM data")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Sat, 25 Nov 2023 17:43:16 +0000 (17:43 +0000)]
sunxi: H616: OrangePi Zero 2: enable USB power supply
The OrangePi Zero 2 has a USB VBUS regulator, controlled by pin PC16.
This is correctly described in the DT, but the patches for supporting
this are still pending.
Meanwhile add our good old CONFIG_USB1_VBUS_PIN to the defconfig file,
to enable power on the USB port and allow using a USB flash drive, for
instance.
Fixes: 6acc5fa581b4 ("sunxi: H616: enable USB support for H616 boards")
Reported-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
John Clark [Mon, 20 Nov 2023 02:35:31 +0000 (02:35 +0000)]
starfive: visionfive2: add device tree overlay support
device tree overlay support requires fdtoverlay_addr_r to be set
before
~~~~~~
Invalid fdtoverlay_addr_r for loading overlays
after
~~~~~
Retrieving file: /boot/overlay/rtc-ds3231.dtbo
Signed-off-by: John Clark <inindev@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Randolph [Fri, 17 Nov 2023 10:39:50 +0000 (18:39 +0800)]
riscv: binman: fix the load field format
Using /bits/ 64 prefix for 64 bits address
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Yu Chien Peter Lin [Thu, 16 Nov 2023 12:46:12 +0000 (20:46 +0800)]
riscv: andes: Fix enable register settings of PLICSW
On 32-core platform, hart31 gets stuck at secondary_hart_loop
as the corresponding enable bit is not set in enable_ipi().
We should program the next word (0x2f84) which is assigned
as the enable register of hart31. It should be done in the same
way when we invoke riscv_send_ipi() to trigger software interrupt
on hart31.
The following diagram shows the enable bits of the fixed PLICSW
scheme.
Pending regs: 0x1000 x---0---0---0---0------0---0
Pending hart ID: 0 1 2 3 ... 30 31
Interrupt ID: 0 1 2 3 4 ... 31 32
| | | | | | |
Enable regs: 0x2000 x---1---0---0---0-...--0---0---> hart0
| | | | | | |
0x2080 x---0---1---0---0-...--0---0---> hart1
| | | | | | |
0x2100 x---0---0---1---0-...--0---0---> hart2
| | | | | | |
0x2180 x---0---0---0---1-...--0---0---> hart3
. . . . . . .
. . . . . . .
. . . . . . .
0x2f00 x---0---0---0---0-...--1---0---> hart30
| | | | | | |
0x2f80 x---0---0---0---0-...--0---1---> hart31
<-------- word 0 -------><--- word 1 --->
This patch includes some cleanups to macros/functions.
Fixes: ebf11273220a ("riscv: andes: Rearrange Andes PLICSW to single-bit-per-hart strategy")
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Randolph <randolph@andestech.com>
Heinrich Schuchardt [Thu, 16 Nov 2023 10:22:51 +0000 (11:22 +0100)]
risc-v: qemu: imply NVME_PCI
CONFIG_NVME=y without CONFIG_NVME_PCI=y does not provide working NVMe
support. Instead of implying CONFIG_NVME we must imply CONFIG_NVME_PCI
which will select CONFIG_NVME.
Fixes: e64db0d92e32 ("riscv: qemu: Enable e1000 and nvme support")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Chanho Park [Sun, 5 Nov 2023 23:13:18 +0000 (08:13 +0900)]
configs: visionfive2: Enable watchdog driver
Enables StarFive Watchdog driver and WDT command.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Chanho Park [Sun, 5 Nov 2023 23:13:17 +0000 (08:13 +0900)]
riscv: dts: jh7110: Add watchdog device tree node
Adds jh7110 watchdog device tree node.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Chanho Park [Sun, 5 Nov 2023 23:13:16 +0000 (08:13 +0900)]
watchdog: Add StarFive Watchdog driver
Add to support StarFive watchdog driver. The driver is imported from
linux kernel's drivers/watchdog/starfive-wdt.c without jh7100 support
because there is no support of jh7100 SoC in u-boot yet.
Howver, this patch has been kept the variant coding style because JH7100
can be added later and have a consistency with the linux driver.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Chanho Park [Sun, 5 Nov 2023 23:13:15 +0000 (08:13 +0900)]
clk: starfive: jh7110: Add watchdog clocks
Add JH7110_SYSCLK_WDT_APB and JH7110_SYSCLK_WDT_CORE clocks for JH7110
watchdog device.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Ilias Apalodimas [Tue, 28 Nov 2023 19:10:31 +0000 (21:10 +0200)]
efi_loader: Make DisconnectController follow the EFI spec
commit
239d59a65e20 ("efi_loader: reconnect drivers on failure")
tried to fix the UninstallProtocol interface which must reconnect
any controllers it disconnected by calling ConnectController()
in case of failure. However, the reconnect functionality was wired in
efi_disconnect_all_drivers() instead of efi_uninstall_protocol().
As a result some SCT tests started failing.
Specifically, BBTestOpenProtocolInterfaceTest333CheckPoint3() test
- Calls ConnectController for DriverImageHandle1
- Calls DisconnectController for DriverImageHandle1 which will
disconnect everything apart from TestProtocol4. That will remain
open on purpose.
- Calls ConnectController for DriverImageHandle2. TestProtocol4
which was explicitly preserved was installed wth BY_DRIVER attributes.
The new protocol will call DisconnectController since its attributes
are BY_DRIVER|EXCLUSIVE, but TestProtocol4 will not be removed. The
test expects EFI_ACCESS_DENIED which works fine.
The problem is that DisconnectController, will eventually call
EFI_DRIVER_BINDING_PROTOCOL.Stop(). But on the aforementioned test
this will call CloseProtocol -- the binding protocol is defined in
'DBindingDriver3.c' and the .Stop function uses CloseProtocol.
If that close protocol call fails with EFI_NOT_FOUND, the current code
will try to mistakenly reconnect all drivers and the subsequent tests
that rely on the device being disconnected will fail.
Move the reconnection in efi_uninstall_protocol() were it belongs.
Fixes: commit 239d59a65e20 ("efi_loader: reconnect drivers on failure")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Thu, 16 Nov 2023 09:29:28 +0000 (10:29 +0100)]
efi_loader: create memory reservations in ACPI case
ACPI tables cannot convey memory reservations for ARM and RISC-V.
x86 uses the BIOS E820 table for this purpose. We cannot simply ignore the
device-tree when booting via ACPI. We have to assign EfiReservedMemory
according to the prior stage device-tree ($fdtaddr) or as fallback the
control device-tree ($fdtcontroladdr).
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 12 Nov 2023 20:55:10 +0000 (13:55 -0700)]
efi: Correct display of table GUIDs
The printf() %pU option decodes GUIDs so it is not necessary to do this
first. Drop the incorrect code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Simon Glass [Sun, 12 Nov 2023 20:55:09 +0000 (13:55 -0700)]
efi: Collect the ACPI tables in the app
Locate these so that they can be displayed using the 'acpi' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Masahisa Kojima [Fri, 27 Oct 2023 07:43:26 +0000 (16:43 +0900)]
scripts/Makefile.lib: print error when no public key is specified
The current build system embeds the EFI Signature List(ESL)
into the dtb to be used in the EFI capsule authentication.
This ESL file is specified through the CONFIG_EFI_CAPSULE_ESL_FILE
Kconfig option. If CONFIG_EFI_CAPSULE_ESL_FILE is not specified,
U-boot build ends up with failure but the cause of failure is not
easily understandable. Current error message is as follows.
FATAL ERROR: Error reading file into data: Is a directoryCheck /home/ubuntu/src/ledge/u-boot/arch/arm/dts/.synquacer-sc2a11-developerbox.dtb.pre.tmp for errors
make[2]: *** [scripts/Makefile.lib:355: arch/arm/dts/synquacer-sc2a11-developerbox.dtb] Error 1
make[1]: *** [dts/Makefile:44: arch-dtbs] Error 2
make: *** [Makefile:1165: dts/dt.dtb] Error 2
make: *** Waiting for unfinished jobs....
This commit shows the error message that CONFIG_EFI_CAPSULE_ESL_FILE
must be specified when the EFI capsule authentication is enabled, then
terminate the build with error.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Weizhao Ouyang <o451686892@gmail.com>
Mattijs Korpershoek [Tue, 21 Nov 2023 16:27:38 +0000 (17:27 +0100)]
doc: sending_patches.rst: s/Superseeded/Superseded
This is a common typo listed in scripts/spelling.txt. Fix it to match the
patchwork status, which is superseded.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tom Rini [Tue, 21 Nov 2023 15:41:07 +0000 (10:41 -0500)]
doc: clang: Update and correct support notes
At this point, clang can be used on both 32bit and 64bit targets without
issue. Make note of logic we have that will inform clang of the
architecture to build for.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Simon Glass [Sun, 19 Nov 2023 15:18:07 +0000 (08:18 -0700)]
sandbox: Fix VPL instructions
Fix the devicetree used with sandbox. This is needed because the
default (full) devicetree must be used by all phases of boot, with
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tom Rini [Mon, 4 Dec 2023 18:46:56 +0000 (13:46 -0500)]
Prepare v2024.01-rc4
Signed-off-by: Tom Rini <trini@konsulko.com>
Heinrich Schuchardt [Mon, 20 Nov 2023 22:25:58 +0000 (23:25 +0100)]
efi_loader: generated SMBIOS table below 4 GiB
We currently use an outdated format 32-bit format for SMBIOS tables.
So we must allocate SMBIOS tables below 4 GiB.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>