net: phy: mv88E61xx: fix ENERGY_DET init for mv88E6071
On mv88E6071 the 'EDet' field offset, width and sense control
bits are different, adjust the driver to init the PHY control
register as needed. This fixes not working link detection and
tftp transfers.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net: phy: mv88e61xx: add CPU port parameter init for 88E6071
On 88E6071 chip the port status register bit field offsets
for duplex and link bits differ. Extend the driver to use 88E6071 specific offset values. The width of bit fields for
speed status differ, too. Adapt for proper port speed
detection on 88E6071.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net: phy: mv88e61xx: rework to enable detection of 88E6071 devices
Extend the driver to init switch register offsets from variables
instead of compile time macros and enable detection of 88E6071 and
compatible devices. Ethernet transfer (e.g. tftp) does not work yet,
so enable the registration of the 'indirect mii' bus for easier PHY
register access by 'mii' command.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Nicolas Ferre [Wed, 23 Oct 2019 10:46:44 +0000 (10:46 +0000)]
net: phy: micrel: make sure the factory test bit is cleared
The KSZ8081 PHY has a factory test mode which is set at the de-assertion
of the reset line based on the RXER (KSZ8081RNA/RND) or TXC
(KSZ8081MNX/RNB) pin. If a pull-down is missing, or if the pin has a
pull-up, the factory test mode should be cleared by manually writing a 0
(according to the datasheet).
Create another ksz8081_config function to handle this case.
Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Michael Walle [Mon, 21 Oct 2019 23:03:10 +0000 (01:03 +0200)]
net: eth-uclass: ignore unavailable devices
device_probe() may fail in which case the seq_id will be -1. Don't
display these devices during startup. While this is only a cosmetic
change, the return value of eth_initialize() will also change to the
actual number of available devices. The return value is only used in
spl_net to decide whether there are any devices to boot from. So
returning only available devices is also more correct in that case.
Signed-off-by: Michael Walle <michael@walle.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Florin Chiculita [Mon, 14 Oct 2019 14:27:07 +0000 (17:27 +0300)]
net: phy: aquantia: wait for phy init sequence to finish
Aquantia quad-phys may take longer to initialize. This commit adds
a polling mechanism for a global alarm bit that tells if phy init
sequence is completed.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Josef Holzmayr [Wed, 2 Oct 2019 19:22:52 +0000 (21:22 +0200)]
net: macb: let miiphy_read/_write pass arbitrary addresses
This allows passing arbitrary addresses through macb_miiphy_read and
macb_miiphy_write, therefore enabling the mii command to access
all mdio bus devices instead of only the defined phy.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Josef Holzmayr [Wed, 2 Oct 2019 19:22:51 +0000 (21:22 +0200)]
net: macb: explicitly pass phy_adr to mdio read and write
To support accessing arbitrary addresses the mii/mdio bus it is
necessary that the macb_mdio_read and macb_mdio_write functions
do not implicitly use the address of the connected phy.
The function signature is extended according to the Linux kernel
equivalent.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stefan Roese [Mon, 30 Sep 2019 08:26:42 +0000 (10:26 +0200)]
net: phy: Increase link up delay in genphy_update_link()
I've noticed that in most cases when genphy_update_link() is called, the
ethernet driver (mt7628-eth in this case) fails with the first ethernet
packets. Resulting in a timeout of the first tftp command. Increasing
the delay in the link check look from 1 to 50 ms and moving it below the
BMSR register read fixes this issue, resulting in a stable ethernet
traffic, even after initial link autonogotiation.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Weijie Gao <weijie.gao@mediatek.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Ramon Fried [Fri, 13 Sep 2019 15:25:03 +0000 (18:25 +0300)]
cmd: mdio/mii: add Kconfig help and allow break dependency
* Add Kconfig help describing the purpose of each command.
* Add CONFIG_CMD_MDIO so it could be selected individually, as
it doesn't depend on the mii command.
* Add Kconfig imply to mii to automatically select the mdio
command.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This version of the RTL-8168 chip can be found on some add-in cards sold
by CSL-Computer GmbH & Co. KG. The chip isn't special in any way, but it
needs to have the ChipCmd register programmed after the DMA descriptors
have been set up, so make sure that happens by adding an entry to the
chip information table.
Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Nevo Hed [Thu, 15 Aug 2019 22:08:44 +0000 (18:08 -0400)]
net: mvpp2: use new MVMDIO driver
This commit ports mvpp2 to use the recently introduced Marvell MDIO
(MVMDIO) driver. It removes direct interaction with the SMI & XSMI
busses. This commit is based in part on earlier work by
Ken Ma <make@marvell.com> in Marvell's own downstream repo:
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/c81dc39.
The above refrenced work was based on an MVMDIO implementation that
never made it into U-Boot. With this patch the mvpp2 driver switches
to use the new MVMDIO driver that is based on a more universal
mdio-uclass implementation.
Signed-off-by: Nevo Hed <nhed+github@starry.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Nevo Hed [Thu, 15 Aug 2019 22:08:43 +0000 (18:08 -0400)]
arm: dts: armada-cp110-*dtsi: add xmdio nodes
Based on upstream-linux
See https://github.com/torvalds/linux/commit/f66b2aff.
However made the XSMI register window 0x16 (22) bytes per my reading
of the functional spec. Similar commits in Marvels own repo bump it
to 0x200 (512) bytes but I did not see the reasoning for that.
net: mvpp2: mark phy as invalid in case of missing appropriate driver
If the phy doesn't match with any existing u-boot drivers, the phy
framework will connect it to the generic one which uid ==
0xffffffff. In this case, act as if the phy wouldn't be declared in
dts. Otherwise, in case of 3310 (for which the driver doesn't exist)
the link is marked as always down. Removing phy entry from dts in case
of 3310 is not a good option because it is required for the
phy_fw_down procedure.
This patch fixes the issue with the link always down on MCBIN board.
nhed: added NULL deref test.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by: Igal Liberman <igall@marvell.com> Tested-by: Igal Liberman <igall@marvell.com> Signed-off-by: Nevo Hed <nhed+github@starry.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stefan Chulski [Thu, 15 Aug 2019 22:08:41 +0000 (18:08 -0400)]
net: mvpp2x: fix traffic stuck after PHY start error
Issue:
- Network stuck if autonegotion fails.
Issue root cause:
- When autonegotiation fails during port open procedure, the packet
processor configuration does not finish and open procedure exits
with error.
- However, this doesn't prevent u-boot network framework from
calling send and receive procedures.
- Using transmit and receive functions of misconfigured packet
processor will cause traffic to get stuck.
Fix:
- Continue packet processor configuration even if autonegotiation
fails. Only error message is triggered in this case.
- Exit transmit and receive functions if there is no PHY link
indication.
- U-boot network framework now calls open procedure again during next
transmit initiation.
Signed-off-by: Stefan Chulski <stefanc@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Tested-by: Igal Liberman <igall@marvell.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
arm: dts: k3-am654-base-board-u-boot: change cpsw2g interface mode to rgmii-rxid
The AM654 SoC doesn't allow to disabling RGMII TX internal delay in CPSW2G
MAC. Hence, change CPSW2G interface mode to "rgmii-rxid" - RGMII with
internal RX delay provided by the PHY, the MAC will add an TX delay in this
case.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net: phy: dp83867: io impedance is not dependent on RGMII delay
Based on commit 27708eb5481b ("net: phy: dp83867: IO impedance is not
dependent on RGMII delay") of mainline linux kernel.
The driver would only set the IO impedance value when RGMII internal delays
were enabled. There is no reason for this. Move the IO impedance block
out of the RGMII delay block.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit c11669a2757e ("net: phy: dp83867: Rework delay rgmii delay
handling") of mainline linux kernel.
The current code is assuming the reset default of the delay control
register was to have delay disabled. This is what the datasheet shows as
the register's initial value. However, that's not actually true: the
default is controlled by the PHY's pin strapping.
This patch:
- insures the other direction's delay is disabled If the interface mode is
selected as RX or TX delay only
- validates the delay values and fail if they are not in range
- checks if the board is strapped to have a delay and is configured to use
"rgmii" mode and warning is generated that "rgmii-id" should have been
used.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net: phy: dp83867: Add ability to disable output clock
Based on commit 13c83cf8af0d ("net: phy: dp83867: Add ability to disable
output clock") of mainline linux kernel.
Generally, the output clock pin is only used for testing and only serves as
a source of RF noise after this. It could be used to daisy-chain PHYs, but
this is uncommon. Since the PHY can disable the output, make doing so an
option. I do this by adding another enumeration to the allowed values of
ti,clk-output-sel.
The code was not using the value DP83867_CLK_O_SEL_REF_CLK as one might
expect: to select the REF_CLK as the output. Rather it meant "keep clock
output setting as is", which, depending on PHY strapping, might not be
outputting REF_CLK.
Change this so DP83867_CLK_O_SEL_REF_CLK means enable REF_CLK output.
Omitting the property will leave the setting as is (which was the previous
behavior in this case).
Out of range values were silently converted into DP83867_CLK_O_SEL_REF_CLK.
Change this so they generate an error.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
dt-bindings: phy: dp83867: Add documentation for disabling clock output
Based on commit 980066e6d964 ("dt-bindings: phy: dp83867: Add documentation
for disabling clock output") of mainline linux kernel.
The clock output is generally only used for testing and development and not
used to daisy-chain PHYs. It's just a source of RF noise afterward.
Add a mux value for "off". I've added it as another enumeration to the
output property. In the actual PHY, the mux and the output enable are
independently controllable. However, it doesn't seem useful to be able
to describe the mux setting when the output is disabled.
Document that PHY's default setting will be left as is if the property
is omitted.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
It turns out the result of 'tftp_load_addr + tftp_load_size' just
overflows (0x100000000) and the test logic in store_block() fails.
Fix this by adjusting the end address to ULONG_MAX when overflow
is detected.
Fixes: a156c47e39ad ("tftp: prevent overwriting reserved memory") Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
sandbox_defconfig does not compile using GCC 9.2.1:
net/net.c: In function ‘net_process_received_packet’:
net/net.c:1288:23: error: taking address of packed member of ‘struct
ip_udp_hdr’ may result in an unaligned pointer value
[-Werror=address-of-packed-member]
1288 | sumptr = (ushort *)&(ip->udp_src);
| ^~~~~~~~~~~~~~
Avoid the error by using a u8 pointer instead of an u16 pointer and
in-lining ntohs().
Simplify the checksumming of the last message byte.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Priyanka Jain [Tue, 5 Nov 2019 04:05:11 +0000 (04:05 +0000)]
net/phy: Fix phy_connect() for phy addr 0
Fix 'mask' calculation in phy_connect() for phy addr '0'.
'mask' is getting set to '0xffffffff' for phy addr '0'
in phy_connect() whereas expected value is '0'.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reported-by: tetsu-aoki via github Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tom Rini [Fri, 6 Dec 2019 00:35:07 +0000 (19:35 -0500)]
net: nfs: Only link in NFS code outside of SPL builds
While we have networking use cases within SPL we do not support loading
files via NFS at this point in time. Disable calling nfs_start() so
that the NFS related code can be garbage collected at link time.
Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Sat, 14 Sep 2019 00:21:16 +0000 (19:21 -0500)]
net: Always build the string_to_enetaddr() helper
Part of the env cleanup moved this out of the environment code and into
the net code. However, this helper is sometimes needed even when the net
stack isn't included.
Move the helper to lib/net_utils.c like it's similarly-purposed
string_to_ip(). Also rename the moved function to similar naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reported-by: Ondrej Jirman <megous@megous.com>
Masahiro Yamada [Tue, 3 Dec 2019 05:28:58 +0000 (14:28 +0900)]
x86: simplify ljmp to 32-bit code
You can directly specify the label as the operand for ljmp.
This commit saves 4-byte code.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed the gas warning] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Fri, 6 Dec 2019 21:45:46 +0000 (16:45 -0500)]
Merge branch '2019-12-06-master-imports'
- Allow for the sysboot command, which is used to parse extlinux.conf
files to be used without PXE support. There is no functional change
here aside from fixing distro boot in a few cases where we actually
lacked the ability to parse the extlinux.conf file
- Add the x509/pkcs7 parsers from Linux, a pre-requisite to EFI Secure
Boot support.
Tom Rini [Wed, 4 Dec 2019 23:54:30 +0000 (18:54 -0500)]
Makefile: Ensure tools directory exists in output prior to use
With the change to make tools/version.h a file we need to make sure that
the output directory exists first otherwise we will get a build failure.
Reported-by: Peter Robinson <pbrobinson@gmail.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Fixes: 4d90f6cd9813 ("tools: Avoid creating symbolic links for tools/version.h") Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Wed, 13 Nov 2019 00:45:01 +0000 (09:45 +0900)]
lib: crypto: add pkcs7 message parser
Imported from linux kernel v5.3:
pkcs7.asn1 without changes
pkcs7.h with changes marked as __UBOOT__
pkcs7_parser.h without changes
pkcs7_parser.c with changes marked as __UBOOT__
AKASHI Takahiro [Wed, 13 Nov 2019 00:45:00 +0000 (09:45 +0900)]
lib: crypto: add x509 parser
Imported from linux kernel v5.3:
x509.asn1 without changes
x509_akid.asn1 without changes
x509_parser.h without changes
x509_cert_parser.c with changes marked as __UBOOT__
x509_public_key.c with changes marked as __UBOOT__
AKASHI Takahiro [Wed, 13 Nov 2019 00:44:58 +0000 (09:44 +0900)]
lib: crypto: add public key utility
Imported from linux kernel v5.3:
asymmetric-type.h with changes marked as __UBOOT__
asymmetric_type.c with changes marked as __UBOOT__
public_key.h with changes marked as __UBOOT__
public_key.c with changes marked as __UBOOT__
AKASHI Takahiro [Wed, 13 Nov 2019 00:44:53 +0000 (09:44 +0900)]
cmd: add asn1_compiler
Imported from linux kernel v5.3:
asn1.h without changes
asn1_ber_bytecode.h without changes
asn1_decoder.h without changes
asn1_compiler.c without changes
This host command will be used to create a ASN1 parser, for example,
for pkcs7 messages or x509 certificates. More specifically, it will
generate *byte code* which will be interpreted by asn1 decoder library.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Wed, 13 Nov 2019 00:44:51 +0000 (09:44 +0900)]
include: kernel.h: include printk.h
Adding "printk.h" will help improve portability from linux kernel
code (in my case, lib/asn1_decoder.c and others) where printf and
pr_* variant functions are used.
AKASHI Takahiro [Wed, 13 Nov 2019 00:44:49 +0000 (09:44 +0900)]
rtc: move date.c from drivers/rtc/ to lib/
In the next commit, rtc_mktime(), for compatibility with linux, will be
implemented using rtc_mktime(), which is no longer drivers/rtc specific.
So move this file under lib/.
AKASHI Takahiro [Wed, 13 Nov 2019 00:44:47 +0000 (09:44 +0900)]
linux_compat: move kmemdup() from ubifs.c to linux_compat.c
linux_compat.c is the best place for kmemdup(), which is currenly used
only in ubifs.c, but will also be used when other kernel files
(in my case, lib/crypto/x509_cert_parser.c and pkcs7_parser.c) will be
imported. So just move it.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Patrice Chotard [Mon, 25 Nov 2019 08:07:37 +0000 (09:07 +0100)]
cmd: Prepare sysboot command independence
As sysboot and pxe commands are sharing piece of code, migrate this
common code into a new file pxe_utils.c to prepare sysboot command
code extraction from pxe.c
Tom Rini [Fri, 6 Dec 2019 15:35:18 +0000 (10:35 -0500)]
Merge tag 'u-boot-rockchip-20191206' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- rockchip pwm driver update to support all the SoCs
- RK3308 GMAC and pinctrl support
- More UART interface support on PX30 and pmugrf reg fix
- Fixup on misc for eth_addr/serial#
- Other updates on variant SoCs
Tom Rini [Fri, 6 Dec 2019 14:56:03 +0000 (09:56 -0500)]
Revert "spl: fix entry_point equal to load_addr"
Due to the (seemingly bogus) assumption of a default
CONFIG_SYS_UBOOT_START value we will revert this change for now and
evaluate it again for the next release along with changes to
CONFIG_SYS_UBOOT_START.
Ben Wolsieffer [Tue, 3 Dec 2019 05:40:05 +0000 (00:40 -0500)]
rockchip: allow loading larger kernels
Recent versions of the Linux kernel with many options enabled have
grown large enough to overwrite the beginning of the initrd. For
example, the kernel I use on my Rock64 and RockPro64 is 34.1 MiB,
while only 31.5 MiB are available between kernel_addr_r and
ramdisk_addr_r.
This patch moves ramdisk_addr_r up by 32 MiB on the RK3328 and RK3399,
allowing for much larger kernels.
Signed-off-by: Ben Wolsieffer <benwolsieffer@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
David Wu [Tue, 3 Dec 2019 09:49:53 +0000 (17:49 +0800)]
pwm: rk_pwm: Make PWM driver to support all Rockchip Socs
This PWM driver can be used to support pwm functions
for on all Rockchip Socs.
The previous chips than RK3288 did not support polarity,
and register layout was different from the RK3288 PWM.
The RK3288 keep the current functions.
RK3328 and the chips after it, which can support hardware lock,
configure duty, period and polarity at next same period, to
prevent the intermediate temporary state.
Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 2 Dec 2019 07:58:17 +0000 (15:58 +0800)]
rockchip: config: add support for firefly-px30 board
This is a core board named Core-PX30-JD4 with a mainboard from Firefly,
name it as firefly-px30 for now.
This board can re-use the dts of PX30, the only difference is the UART IO,
the firefly use UART2 M1 while evb use UART2 M0.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Heiko Stuebner [Fri, 29 Nov 2019 15:40:43 +0000 (16:40 +0100)]
rockchip: misc: protect serial# from getting overwritten
serial# is one of the vendor properties and thus protected from being
overwritten if already set. If env_set is called anyway this result in
some nasty warnings, so check for presence before trying that.
In the same direction check for the presence of cpuid# and compare it
to the actual hardware and emit a warning if they don't match.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockchip: px30: Add support for using UART3 as debug UART
Some generic PX30 SoMs found in the wild use UART3 as their debug output
instead of UART2 (used for MMC) and UART5.
Make it possible to use UART3 as early debug output, with the associated
clock and pinmux configuration. Two sets of output pins are supported (M0/M1).
Future users should also note that the pinmux default in the dts is to use
the M1 pins while the Kconfig option takes M0 as a default.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Andy Yan [Tue, 26 Nov 2019 13:15:39 +0000 (21:15 +0800)]
rockchip: px5: enable spl-fifo-mode for emmc for px5-evb
We need load some parts of ATF to sram, but rockchip
dwmmc controllers can't do dma to non-ddr addresses
space, so set the mmc controller into fifo mode in spl.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Andy Yan [Tue, 26 Nov 2019 13:15:38 +0000 (21:15 +0800)]
rockchip: rk3308: enable spl-fifo-mode for emmc
We need load some parts of ATF to sram, but rockchip
dwmmc controllers can't do dma to non-ddr addresses
space, so set the mmc controller into fifo mode in spl.
And show my best respect to Heiko's work for this solution.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Andy Yan [Tue, 26 Nov 2019 13:15:37 +0000 (21:15 +0800)]
doc: rockchip: Update build instruction for rk3308
After commit d8765e2422cd ("Enable building of u-boot.itb
on Rockchip platform"), u-boot.itb will automatically
generated by "make all" command, manually command
"make u-boot.itb" is no longer needed.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The da850-evm doesn't have the boot pins configured in a way
to make MMC/SD booting an option, and MMC/SD support is not
enabled in SPL. Therefore, there is no need to support raw mode
mmc/sd support in SPL.
This patch disables CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
Giulio Benetti [Mon, 25 Nov 2019 16:18:20 +0000 (17:18 +0100)]
spl: fix entry_point equal to load_addr
At the moment entry_point is set to image_get_load(header) that sets it
to "load address" instead of "entry point", assuming entry_point is
equal to load_addr, but it's not true. Then load_addr is set to
"entry_point - header_size", but this is wrong too since load_addr is
not an entry point.
So use image_get_ep() for entry_point assignment and image_get_load()
for load_addr assignment.
AKASHI Takahiro [Tue, 26 Nov 2019 08:28:49 +0000 (17:28 +0900)]
test/py: test_fs: add tests for creating/deleting many files
# This is actually a resent patch of
# [1] https://lists.denx.de/pipermail/u-boot/2019-May/369170.html
Two test cases are added under test_fs_ext:
test case 10: for root directory
test case 11: for non-root directory
Those will verify a behavior fixed by the commits related to
root directory
("fs: fat: allocate a new cluster for root directory of fat32" and
"fs: fat: flush a directory cluster properly"), and focus on
handling long-file-name directory entries under a directory.
Unlink test for FAT file system seems to fail at test_unlink2.
(When I added this test, I haven't seen any errors though.)
for example,
===8<===
fs_obj_unlink = ['fat', '/home/akashi/tmp/uboot_sandbox_test/128MB.fat32.img']
def test_unlink2(self, u_boot_console, fs_obj_unlink):
"""
Test Case 2 - delete many files
"""
fs_type,fs_img = fs_obj_unlink
with u_boot_console.log.section('Test Case 2 - unlink (many)'):
output = u_boot_console.run_command('host bind 0 %s' % fs_img)
for i in range(0, 20):
output = u_boot_console.run_command_list([
'%srm host 0:0 dir2/0123456789abcdef%02x' % (fs_type, i),
'%sls host 0:0 dir2/0123456789abcdef%02x' % (fs_type, i)])
assert('' == ''.join(output))
This can happen when fat_itr_next() wrongly detects an already-
deleted directory entry.
File deletion, which was added in the commit f8240ce95d64 ("fs: fat:
support unlink"), is implemented by marking its entry for a short name
with DELETED_FLAG, but related entry slots for a long file name are kept
unmodified. (So entries will never be actually deleted from media.)
To handle this case correctly, an additional check for a directory slot
will be needed in fat_itr_next().
In addition, I added extra comments about long file name and short file
name format in FAT file system. Although they are not directly related
to the issue, I hope it will be helpful for better understandings
in general.
The mmc CID value is one of the input parameters used to provision the
RPMB key. The trusted execution environment expects this value to be
specified in big endian format.
Before this fix, on little endian systems, the value returned by the
linux kernel mmc driver differed from the one returned by u-boot.
This meant that if linux provisioned the RPMB key, u-boot would not
have access to the partition (and the other way around).
Michael Walle [Sun, 1 Dec 2019 16:45:18 +0000 (17:45 +0100)]
drivers: pci: ignore disabled devices
PCI devices may be disabled in the device tree. Devices which are probed
by the device tree handle the "status" property and are skipped if
disabled. Devices which are probed by the PCI enumeration don't check
that property. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Alex Marginean <alexandru.marginean@nxp.com> Tested-by: Alex Marginean <alexandru.marginean@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Miquel Raynal [Fri, 25 Oct 2019 17:39:31 +0000 (19:39 +0200)]
mtd: Makefile: deep cleanup
Move MTD-related lines out of the root Makefile. Put them in their
respective directories. Enclose some of these new lines to skip them
when building the SPL. MTD core files and some MTD device drivers are
compiled in a mtd.o object and included in the final object only if
MTD support is required (there are two different symbols for that, one
for U-Boot and one for the SPL).
Now that all defconfigs have been fixed, we can stop the logic where
enabling a command selects the core files to compile. This logic is
broken since selecting a symbol with a 'depends on' will not enforce
this secondary dependency.
Miquel Raynal [Fri, 25 Oct 2019 17:39:29 +0000 (19:39 +0200)]
cmd: nand/sf: isolate legacy code
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.
This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now] Signed-off-by: Tom Rini <trini@konsulko.com>
Miquel Raynal [Thu, 3 Oct 2019 17:50:24 +0000 (19:50 +0200)]
mtd: spi: SPI_FLASH_MTD depends on MTD
It is already the case that all defconfigs with SPI_FLASH_MTD also
declare using MTD, but let's make this consistent and enforce it in
Kconfig. Most of the time SPI_FLASH_MTD is used in conjunction with
UBI, which already depends on MTD.
Suggested-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Miquel Raynal [Thu, 3 Oct 2019 17:50:21 +0000 (19:50 +0200)]
mtd: nand: add includes in NAND core to avoid warnings
Because of the include's game, when some files are compiled for a SPI
NAND device, no warning appears. But when it is for a raw NAND device,
GCC complains. Fix these warning by including <common.h>.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
projects / u-boot.git / log