Sean Anderson [Mon, 17 Oct 2022 15:45:10 +0000 (11:45 -0400)]
arm: layerscape: Don't select FSL_IFC when booting from SD card
FSL_IFC should only be selected when booting from NAND flash (or when
NAND_FSL_IFC is enabled). The existing logic does this correctly when
QSPI is also enabled, but not when just booting from SD.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Wei Lu [Mon, 26 Sep 2022 08:18:49 +0000 (16:18 +0800)]
ls1043ardb: nand driver fixups for revision v7.0 boards
The LS1043ARDB rev v7.0 board replace nand device MT29F4G08ABBDAH4-AITX:D
with MT29F4G08ABBFAH4-AIT:F. Reflecting this change in board_fix_fdt().
CPLD V3.0 is needed for nandboot as the nand device changed.
A new macro CPLD_CFG_RCW_SRC_NAND_4K(4Kpage) is added to distinguish from
CPLD_CFG_RCW_SRC_NAND(2Kpage) to support nandboot on rev v7.0 board.
Signed-off-by: Wei Lu <w.lu@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sean Anderson [Fri, 23 Sep 2022 16:05:51 +0000 (12:05 -0400)]
arm64: ls104x: Enable eDMA snooping
This enables eDMA snooping on the LS1043A and LS1046A. This will allow
marking the I2C, LPUART, and SPI devices on these SoCs as DMA coherent.
Oddly, this bit is only documented for the LS1043A, and is marked as
"reserved" in the LS1046ARM. I have tested this patch on the LS1046A
and found that marking i2c0 as dma-coherent works without issue.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Acked-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ilias Apalodimas [Sun, 16 Oct 2022 08:36:32 +0000 (11:36 +0300)]
efi_loader: remove efi_delete_handle on loadfile2
Loadfile2 code is installing two protocols on it's own handle
and uses efi_delete_handle() to clean it up on failure(s). However
commit 05c4c9e21ae6 ("efi_loader: define internal implementations of
install/uninstallmultiple") prepares the ground for us to clean up
efi_delete_handle() used in favor of Install/UninstallMultipleProtocol.
While at it clean up the non needed void casts to (void *) on the
protolcol installation.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Paul Barker [Wed, 5 Oct 2022 12:18:34 +0000 (13:18 +0100)]
spi: Implement spi_set_speed
This function is already defined in spi.h but no implementation of it
currently exists in the tree. The implementation is based on the static
function spi_set_speed_mode(). The function prototype is modified so
that an success or error condition can be returned to the caller.
Signed-off-by: Paul Barker <paul.barker@sancloud.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Pali Rohár [Sun, 9 Oct 2022 19:38:25 +0000 (21:38 +0200)]
Nokia RX-51: Fix double space key press
Space key is indicated by two different bits. Some HW models indicate press
of space key only by the first bit. Qemu indicates it by both bits at the
same time, which is currently interpreted by u-boot as double key press.
Fix this issue by setting first bit when only second is set (to support HW
models which indicate press only by second bit) and always clearing second
bit before processing to not report double space key press.
Ignacio Zamora [Sat, 8 Oct 2022 14:50:56 +0000 (09:50 -0500)]
Fix typo in CONFIG_USBNET_DEVADDR
Fix typo that was caused by the same feature being split in to 2 different
configuration options. Replace CONFIG_USBNET_DEVADDR with
CONFIG_USBNET_DEV_ADDR
Robert Marko [Fri, 7 Oct 2022 09:52:44 +0000 (11:52 +0200)]
smem: msm: add missing <linux/sizes.h>
MSM SMEM driver is currently missing <linux/sizes.h> header and throws
the following compile error:
drivers/smem/msm_smem.c: In function ‘qcom_smem_get_ptable’:
drivers/smem/msm_smem.c:635:71: error: ‘SZ_4K’ undeclared (first use in this function)
635 | ptable = smem->regions[0].virt_base + smem->regions[0].size - SZ_4K;
Signed-off-by: Robert Marko <robert.marko@sartura.hr> Cc: luka.perkov@sartura.hr
Patrick Delaunay [Fri, 30 Sep 2022 07:36:38 +0000 (09:36 +0200)]
firmware: scmi: fix the multi channel support with CCF
When the CCF is activated, the dev->parent is not necessary
the reference to SCMI transport and the function devm_scmi_of_get_channel
failed for the registered SCMI clock, child for protocol@14,
the channel is null and the SCMI clock driver crash for any operations.
This patch changes the first parameter of the ops of_get_channel(),
aligned with other process_msg() to pass directly the good reference,
i.e. parent result of find_scmi_transport_device(dev)
which return the reference of the scmi transport device.
Robert Marko [Tue, 6 Sep 2022 11:30:33 +0000 (13:30 +0200)]
cmd: add temperature command
Currently, there is no way for users to check the readings from thermal
sensors from U-boot console, only some boards print it during boot.
So, lets add a simple "temperature" command that allows listing thermal
uclass devices and getting their value.
Note that the thermal devices are intenionally probed if list is used as
almost always they will not get probed otherwise and there is no way for
users to manually call probe on a certain device from console.
Assumption is made that temperature is returned in degrees C and not
milidegrees like in Linux as this is what most drivers seem to return.
Signed-off-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Simon Glass <sjg@chromium.org>
John Keeping [Wed, 7 Sep 2022 11:11:42 +0000 (12:11 +0100)]
pinctrl: fix buffer size for pinctrl_generic_set_state_prefix()
This buffer has the concatenated prefix and name written into it, so it
must be large enough to cover both strings plus the terminating NUL.
Fixes: 92c4a95ec7 ("pinctrl: Add new function pinctrl_generic_set_state_prefix()") Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Steven Lawrance [Wed, 14 Sep 2022 18:57:28 +0000 (20:57 +0200)]
boot: image-pre-load: Check environment for location of signature info
Setting an alternative signature info node in "pre_load_sig_info_path"
allows verification of an image using the bootm pre-load mechanism with
a different key, e.g.: setenv pre_load_sig_info_path "/alt/sig" ; bootm
preload [addr]
Signed-off-by: Steven Lawrance <steven.lawrance@softathome.com> Reviewed-by: Simon Glass <sjg@chromium.org>
cmd: pxe: add alias devicetree-overlay for fdtoverlays
This adds keyword devicetree-overlay as an alias for fdtoverlays in
extlinux (sysboot) and pxe to better follow the Boot Loader Specification
[1], improves documentation around them by adding an example for both
fdtoverlays and devicetree-overlay and the environment variable required
for this feature. The link for the spec is updated to the current one.
[1] https://systemd.io/BOOT_LOADER_SPECIFICATION/
Signed-off-by: Edoardo Tomelleri <e.tomell@gmail.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
common/spl/spl_atf.c:187:51: warning: value size does not match register
size specified by the constraint and modifier [-Wasm-operand-widths]
__asm__ __volatile__("msr DAIF, %0\n\t" : : "r" (daif) : "memory");
^
common/spl/spl_atf.c:187:34: note: use constraint modifier "w"
__asm__ __volatile__("msr DAIF, %0\n\t" : : "r" (daif) : "memory");
^~
%w0
Use %x0 to match what Linux does in <asm/sysreg.h> write_sysreg().
Signed-off-by: Alistair Delva <adelva@google.com> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Michael Walle <michael@walle.cc> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Cc: Nick Desaulniers <ndesaulniers@google.com>
Nick Desaulniers [Mon, 26 Sep 2022 20:47:40 +0000 (20:47 +0000)]
Makefile: apply dynamic relocations for LLD
It seems that for aarch64, unless we apply dynamic relocations to the
location being relocated, we fail to boot.
As Fangrui notes:
For dynamic relocations using the RELA format (readelf -Wr), GNU ld
sets the initial content to r_addend; ld.lld doesn't do that by
default (needs --apply-dynamic-relocs).
Otherwise .rodata appears to be full of NUL-bytes before relocation,
causing crashes when trying to invoke the function pointers in
init_sequence_f from initcall_run_list().
Link: https://reviews.llvm.org/D42797 Suggested-by: Fangrui Song <maskray@google.com> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Alistair Delva <adelva@google.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Cc: Nick Desaulniers <ndesaulniers@google.com>
examples: standalone: Fix build with LLVM toolchain
When building the standalone example with llvm, the link step fails:
examples/standalone/libstubs.o: In function `dummy':
include/_exports.h:10: undefined reference to `jt'
include/_exports.h:11: undefined reference to `jt'
include/_exports.h:12: undefined reference to `jt'
include/_exports.h:13: undefined reference to `jt'
include/_exports.h:14: undefined reference to `jt'
examples/standalone/libstubs.o:include/_exports.h:15:
more undefined references to `jt' follow
Indeed, the standalone libstubs.o does use the jt symbol, but it was
marked 'static' in stubs.c. It's strange how gcc builds are working.
Signed-off-by: Alistair Delva <adelva@google.com> Cc: Rick Chen <rick@andestech.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Cc: Nick Desaulniers <ndesaulniers@google.com>
usb: gadget: fastboot: detach usb on reboot commands
When host issues "fastboot reboot fastboot", it's expected that the
board drops the USB connection before resetting.
On some boards, such as Khadas VIM3L and SEI610, this is not the case.
We observe the following error:
$ fastboot reboot fastboot
Rebooting into fastboot OKAY [ 0.004s]
fastboot: error: Failed to boot into userspace fastboot; one or more components might be unbootable.
This does not happen when we use the RST button on the board.
It can be reproduced in linux with:
# echo b > /proc/sysrq-trigger
In this case, we hit a undefined hardware behavior, where D+ and D-
are in an unknown state. Therefore the host can't detect usb
disconnection.
Make sure we always call usb_gadget_release() when a "fastboot reboot"
command is issued.
Note: usb_gadget_release() should be called before g_dnl_unregister()
because g_dnl_unregister() triggers a complete() call on each
endpoint (thus calling do_reset()).
In drivers usb/host/{ehci,ohci}-generic.c, {ehci,ohci}_setup_phy() and
{ehci,ohci}_shutdown_phy() shares 95% of common code.
Factorize this code in new generic_{setup,shudown}_phy() functions.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org>
Marek Vasut [Tue, 23 Aug 2022 17:06:51 +0000 (19:06 +0200)]
usb: gadget: Clean up Makefile ifdeffery
Take the USB_ETHER ifdef block apart and make use of obj-$(VAR) instead
to include the source files in build. The duplicate CI_UDC entry is now
removed, the USB_DEVICE ifdef is now reduced to core.o ep.o addition,
the ether.o can be conditionally compiled in using USB_ETHER.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Marek Vasut [Mon, 19 Sep 2022 19:19:23 +0000 (21:19 +0200)]
usb: Add missing guard around env_get() in usb_hub
The env_get() might be undefined in case ENV_SUPPORT is disabled,
which may happen e.g. in SPL. Add missing ifdef guard around the
env_get() to prevent build failure.
Signed-off-by: Marek Vasut <marex@denx.de> Tested-by: Fabio Estevam <festevam@denx.de>
The CloseProtocol() boot service requires a handle as first argument.
Passing the protocol interface is incorrect.
CloseProtocol() only has an effect if called with a non-zero value for
agent_handle. HandleProtocol() uses an opaque agent_handle when invoking
OpenProtocol() (currently NULL). Therefore HandleProtocol() should be
avoided.
* Replace the LocateHandle() call by efi_search_protocol().
* Remove the CloseProtocol() call.
Fixes: 8d99026f0697 ("efi_loader: capsule: support firmware update") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
efi_loader: CloseProtocol in tcg2_measure_gpt_data
The CloseProtocol() boot service requires a handle as first argument.
Passing the protocol interface is incorrect.
CloseProtocol() only has an effect if called with a non-zero value for
agent_handle. HandleProtocol() uses an opaque agent_handle when invoking
OpenProtocol() (currently NULL). Therefore HandleProtocol() should be
avoided.
* Replace the LocateHandle() call by efi_search_protocol().
* Remove the CloseProtocol() call.
* Remove a superfluous goto.
Tom Rini [Mon, 10 Oct 2022 12:17:08 +0000 (08:17 -0400)]
Merge tag 'u-boot-nand-20221009' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash
- mtd: Update the function name to 'rfree'
- Support NAND ONFI EDO mode for imx8mn architecture
- dm: clk: add missing stub when CONFIG_CLK is deactivated
Alexander Dahl [Fri, 7 Oct 2022 12:19:57 +0000 (14:19 +0200)]
fpga: virtex2: Fix printf format string warnings
Warning appears if built with FPGA_DEBUG defined:
CC drivers/fpga/virtex2.o
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c: In function ‘virtex2_ssm_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c:333:11: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ {aka ‘long unsigned int’} [-Wformat=]
PRINTF("%s:%d:done went active early, bytecount = %d\n",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__func__, __LINE__, bytecount);
~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c:25:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt, args...) printf(fmt, ##args)
^~~
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c: In function ‘virtex2_ss_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c:468:12: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ {aka ‘long unsigned int’} [-Wformat=]
PRINTF("%s:%d:done went active early, bytecount = %d\n",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__func__, __LINE__, bytecount);
~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c:25:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt, args...) printf(fmt, ##args)
^~~
Alexander Dahl [Fri, 7 Oct 2022 12:19:56 +0000 (14:19 +0200)]
fpga: spartan3: Fix printf arguments warning
The additional comma messes up the arguments.
Warning appears if built with FPGA_DEBUG defined:
CC drivers/fpga/spartan3.o
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c: In function ‘spartan3_sp_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c:118:11: warning: too many arguments for format [-Wformat-extra-args]
PRINTF ("%s: Function Table:\n"
^~~~~~~~~~~~~~~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c:18:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt,args...) printf (fmt ,##args)
^~~
Fixes: 875c78934ee2 ("Add Xilinx Spartan3 family FPGA support Patch by Kurt Stremerch, 14 February 2005") Signed-off-by: Alexander Dahl <ada@thorsis.com> Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/20221007122003.11239-4-ada@thorsis.com
Alexander Dahl [Fri, 7 Oct 2022 12:19:55 +0000 (14:19 +0200)]
fpga: spartan2: Fix printf arguments warning
That extra comma messes up format arguments.
Warning appears if built with FPGA_DEBUG defined:
CC drivers/fpga/spartan2.o
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan2.c: In function ‘spartan2_sp_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan2.c:112:11: warning: too many arguments for format [-Wformat-extra-args]
PRINTF ("%s: Function Table:\n"
^~~~~~~~~~~~~~~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan2.c:12:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt,args...) printf (fmt ,##args)
^~~
CC drivers/fpga/spartan3.o
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c: In function ‘spartan3_sp_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c:117:11: warning: too many arguments for format [-Wformat-extra-args]
PRINTF ("%s: Function Table:\n"
^~~~~~~~~~~~~~~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c:17:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt,args...) printf (fmt ,##args)
^~~
Michal Simek [Wed, 5 Oct 2022 09:39:27 +0000 (11:39 +0200)]
xilinx: zynqmp: Load pmufw configuration before checking access
Before this patch you could see in the log:
U-Boot SPL 2022.10-rc5 (Sep 29 2022 - 15:29:27 +0200)
PMUFW: v1.1
Loading new PMUFW cfg obj (32 bytes)
PMUFW: No permission to change config object
Loading new PMUFW cfg obj (2032 bytes)
where it is visible that permission is check before sending PMUFW
configuration (big size).
When this patch is applied it is visible that order is correct.
U-Boot SPL 2022.10-rc5 (Sep 29 2022 - 15:47:08 +0200)
Loading new PMUFW cfg obj (2032 bytes)
PMUFW: v1.1
Loading new PMUFW cfg obj (32 bytes)
+board/xilinx/common/board.c:479:37: error: the comparison will always
evaluate as 'true' for the address of 'mac_addr' will never be NULL
[-Werror=address]
+ 479 | if (!desc->mac_addr[i])
+ | ^
xilinx: zynqmp: change the type of multiboot variable
In function ‘set_dfu_alt_info’ a comparison of a u8 value against
0 is done. Since it is always false, change the signature of this
function to use an `int` instead, which match the type used in caller:
`multi_boot()`.
Fix the following warning triggered with W=1:
board/xilinx/zynqmp/zynqmp.c:651:23:
warning: comparison is always false due to limited range of data type
[-Wtype-limits]
651 | if (multiboot < 0)
Fabio Estevam [Fri, 7 Oct 2022 14:35:53 +0000 (11:35 -0300)]
mtd: Update the function name to 'rfree'
Since commit 8d38a8459b0d ("mtd: Rename free() to rfree()")
the function has been renamed to rfree(), so update the description
inside the mtd_oob_region structure as well.
Roger Quadros [Wed, 28 Sep 2022 11:42:35 +0000 (14:42 +0300)]
mtd: nand: Fix SPL build after migration of CONFIG_SYS_NAND_SELF_INIT to Kconfig
This fixes the below build error if nand.c is included in
an SPL build.
/work/u-boot/drivers/mtd/nand/raw/nand.c: In function ‘nand_init_chip’:
/work/u-boot/drivers/mtd/nand/raw/nand.c:82:28: error: ‘nand_chip’ undeclared (first use in this function)
82 | struct nand_chip *nand = &nand_chip[i];
| ^~~~~~~~~
/work/u-boot/drivers/mtd/nand/raw/nand.c:82:28: note: each undeclared identifier is reported only once for each function it appears in
/work/u-boot/drivers/mtd/nand/raw/nand.c:84:20: error: ‘base_address’ undeclared (first use in this function); did you mean ‘base_addr’?
84 | ulong base_addr = base_address[i];
| ^~~~~~~~~~~~
| base_addr
Fixes: 068c41f1cc77 ("Finish conversion CONFIG_SYS_NAND_SELF_INIT to Kconfig") Signed-off-by: Roger Quadros <rogerq@kernel.org> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tom Rini [Fri, 7 Oct 2022 15:25:05 +0000 (11:25 -0400)]
Merge branch '2022-10-07-riscv-toolchain-update'
- Update RISC-V to use 32bit or 64bit toolchains, depending on if we're
building for 32bit or 64bit CPUs. This requires updating the Docker
container as well to have the 32bit toolchain.
- Assorted platform updates for developerbox, armv8 platforms in
general, TI K3 and AM65 platforms, nuvoton NPCM845 SoC and then clock
driver, ftgpio010 support, and common/board_f cleanups.
Alexandre Ghiti [Mon, 3 Oct 2022 16:07:54 +0000 (18:07 +0200)]
riscv: Fix build against binutils 2.38
The following description is copied from the equivalent patch for the
Linux Kernel proposed by Aurelien Jarno:
>From version 2.38, binutils default to ISA spec version 20191213. This
means that the csr read/write (csrr*/csrw*) instructions and fence.i
instruction has separated from the `I` extension, become two standalone
extensions: Zicsr and Zifencei. As the kernel uses those instruction,
this causes the following build failure:
Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Christian Stewart <christian@paral.in> Reviewed-by: Rick Chen <rick@andestech.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Rick Chen <rick@andestech.com>
For building riscv32 targets we should use the riscv32 toolchain.
Add it to the Docker image.
Drop the riscv toolchain-alias as we do not need it in future.
While in here, update to the latest "jammy" tag.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Rick Chen <rick@andestech.com>
[trini: Update to latest jammy tag] Signed-off-by: Tom Rini <trini@konsulko.com>
Ravi Gunasekaran [Thu, 22 Sep 2022 09:51:23 +0000 (15:21 +0530)]
net: ti: cpsw-mdio: Add workaround for errata i2329
In certain TI SoCs, on the CPSW and ICSS peripherals, there is
a possibility that the MDIO interface returns corrupt data on
MDIO reads or writes incorrect data on MDIO writes. There is also
a possibility for the MDIO interface to become unavailable until
the next peripheral reset.
The workaround is to configure the MDIO in manual mode and disable the
MDIO state machine and emulate the MDIO protocol by reading and writing
appropriate fields in MDIO_MANUAL_IF_REG register of the MDIO controller
to manipulate the MDIO clock and data pins.
More details about the errata i2329 and the workaround is available in:
https://www.ti.com/lit/er/sprz487a/sprz487a.pdf
Add implementation to disable MDIO state machine, configure MDIO in manual
mode and provide software MDIO read and writes via MDIO bitbanging. Allow
the MDIO to be initialized based on the need for manual mode.
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Include linux/sizes.h because it defines SZ_64K which is used in many
places inside k3-udma.c
This fixes the error: ‘SZ_64K’ undeclared which appears during build
time
Signed-off-by: Dhruva Gole <d-gole@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
projects / u-boot.git / log