Define in the RCC clock provider node which root clocks the driver
depends on. These are root oscillators, which may be present or
not, upon FDT content.
This update binding is introduced in Linux kernel device tree by patch
"ARM: dts: stm32: move clocks/resets to SCMI resources for stm32mp15"
This patch is a preliminary step for SCMI support of stm32mp15
boards with trusted boot chain, based on TF-A or OP-TEE.
Patrice Chotard [Wed, 20 Jan 2021 13:42:04 +0000 (14:42 +0100)]
mtd: spinand: Add WATCHDOG_RESET() in spinand_mtd_read/write()
In case of big area read/write on spi nand, watchdog timeout may occurs.
To fix that, add WATCHDOG_RESET() in spinand_mtd_read() and
spinand_mtd_write() to ensure that watchdog is reset.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrice Chotard [Wed, 20 Jan 2021 13:42:03 +0000 (14:42 +0100)]
mtd: nand: Add WATCHDOG_RESET() in nanddev_mtd_erase()
In case of big area erased on nand, watchdog timeout may occurs.
To fix that, add WATCHDOG_RESET() in nanddev_mtd_erase() to ensure that
watchdog is reset.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrice Chotard [Wed, 20 Jan 2021 13:42:02 +0000 (14:42 +0100)]
spi: stm32_qspi: Add WATCHDOG_RESET in _stm32_qspi_read_fifo()
In case of reading large area and memory-map mode is misconfigured
(memory-map size declared lower than the real size of the memory chip)
watchdog can be triggered.
Add WATCHDOG_RESET() in _stm32_qspi_read_fifo to fix it.
Issue reproduced with stm32mp157c-ev1 board and memory map size set to
1, with following command:
sf read 0xC0000000 0 0x4000000
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In drivers we use a family of printing functions including pr_err() and
pr_cont(). CONFIG_LOGLEVEL is used to control which of these lead to output
via printf().
Our logging functions allow finer grained control of output. So replace
printf() by the matching logging functions. The usage of CONFIG_LOGLEVEL
remains unchanged.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Fri, 26 Feb 2021 17:41:06 +0000 (12:41 -0500)]
Merge tag 'u-boot-stm32-20210226' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Add USB host boot support in stm32mp1 config
- Enable uefi related commands for STMicroelectronics STM32MP15 boards
- Remove duplicate uart nodes in stm32mp15 device tree
efi_loader: limit output length for VenHw, VenMedia
VenHw and VenMedia device path nodes may carry vendor defined data of
arbitrary length. When converting a device path node to text ensure that we
do not overrun our internal buffer.
In our implementation of
EFI_DEVICE_PATH_TO_TEXT_PROTOCOL.ConvertDevicePathToText() we could first
determine the output length and then allocate buffers but that would nearly
double the code size. Therefore keep the preallocated buffers and truncate
excessive device paths instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Ilias Apalodimas [Fri, 26 Feb 2021 12:52:51 +0000 (14:52 +0200)]
configs: stm32mp1: enable uefi related commands
The board can boot with UEFI. With the latest changes in U-Boot's
EFI subsystem we also have support for EFI runtime variables, without
SetVariable support. We can also store the EFI variables in a file on the
ESP partition and preserve them across reboots.
The env and efidebug commands are missing in order to configure
EFI variables and the efibootmgr though. Since U-Boot's default config
enables other EFI related commands (e.g bootefi), let's add the env related
and efidebug commands and allow users to do that
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrick Delaunay [Wed, 24 Feb 2021 10:00:56 +0000 (11:00 +0100)]
arm: dts: stm32mp15: remove duplicate uart nodes
Remove duplicated uart nodes introduced with commit 62f95af92a3f
("ARM: dts: stm32mp1: DT alignment with Linux kernel v5.9-rc4"),
because the uart nodes wasn't correctly ordered in alphabetic order.
Only cosmetic: the generated device tree don't change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Stefan Brüns [Sat, 20 Feb 2021 16:26:06 +0000 (17:26 +0100)]
usb: kbd: Also accept keyboards with Interrupt OUT endpoint
The OUT endpoint can just be ignored as it is not used, just as the
corresponding Set_Report request for IN-only interfaces. E.g. the
Linux gadget hid keyboard also provides an interrupt endpoint.
Also cleanup confusing debug messages like "found set protocol", which
is printed when a keyboard device is found, while the Set_Protocol request
is issued quite some time later.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Sean Anderson [Fri, 5 Feb 2021 14:39:02 +0000 (09:39 -0500)]
doc: Document partition specifications
This documents the way U-Boot understands partitions specifications.
This also updates the fastboot documentation for the changes in the
previous commit.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Fri, 5 Feb 2021 14:39:01 +0000 (09:39 -0500)]
doc: Rename k210 partitions anchor
This anchor is only for the k210 partition layout, so rename it
appropriately. This keeps it from conflicting with the (to be added)
anchor for U-Boot partitions in general.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Fri, 5 Feb 2021 14:39:00 +0000 (09:39 -0500)]
fastboot: Allow u-boot-style partitions
This adds support for partitions of the form "dev.hwpart:part" and
"dev#partname". This allows one to flash to eMMC boot partitions without
having to use CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT. It also allows one to
flash to an entire device without needing CONFIG_FASTBOOT_MMC_USER_NAME.
Lastly, one can also flash MMC devices other than
CONFIG_FASTBOOT_FLASH_MMC_DEV.
Because devices can be specified explicitly, CONFIG_FASTBOOT_FLASH_MMC_DEV
is used only when necessary for existing functionality. For those cases,
fastboot_mmc_get_dev has been added as a helper function. This allows
There should be no conflicts with the existing system, but just in case, I
have ordered detection of these names after all existing names.
The fastboot_mmc_part test has been updated for these new names.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Fri, 5 Feb 2021 14:38:58 +0000 (09:38 -0500)]
fastboot: Remove mmcpart argument from raw_part_get_info_by_name
The only thing mmcpart was used for was to pass to blk_dselect_hwpart.
This calls blk_dselect_hwpart directly from raw_part_get_info_by_name. The
error handling is dropped, but it is reintroduced in the next commit
(albeit less specificly).
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Fri, 5 Feb 2021 14:38:55 +0000 (09:38 -0500)]
part: Give several functions more useful return values
Several functions in disk/part.c just return -1 on error. This makes them
return different errnos for different failures. This helps callers
differentiate between failures, even if they cannot read stdout.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Fri, 5 Feb 2021 14:38:54 +0000 (09:38 -0500)]
test: dm: Add test for fastboot mmc partition naming
This test verifies the mapping between fastboot partitions and partitions
as understood by U-Boot. It also tests the creation of GPT partitions,
though that is not the primary goal.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Fri, 5 Feb 2021 14:38:53 +0000 (09:38 -0500)]
mmc: sandbox: Add support for writing
This adds support writing to the sandbox mmc backed by an in-memory
buffer. The unit test has been updated to test reading, writing, and
erasing. I'm not sure what MMCs erase to; I picked 0, but if it's 0xFF
then that can be easily changed.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
- turris_mox: Enhancements, mostlly defconfig changes (Pali)
- pci-aardvark: Set Max Payload Size and Max Read Request Size
to 512 bytes (Pali)
- pci_mvebu: Minor cleanup and refactoring (Marek)
- Upgrade A38x DDR3 training to version 14.0.0 (Marek)
Reto Schneider [Thu, 11 Feb 2021 12:05:48 +0000 (13:05 +0100)]
mtd: nand: spi: Support GigaDevice GD5F1GQ5UExxG
The relevant changes to the already existing GD5F1GQ4UExxG support has
been determined by consulting the GigaDevice product change notice
AN-0392-10, version 1.0 from November 30, 2020.
As the overlaps are huge, variable names have been generalized
accordingly.
Apart form the lowered ECC strength (4 instead of 8 bits per 512 bytes),
the new device ID, and the extra quad IO dummy byte, no changes had to
be taken into account.
New hardware features are not supported, namely:
- Power on reset
- Unique ID
- Double transfer rate (DTR)
- Parameter page
- Random data quad IO
The inverted semantic of the "driver strength" register bits, defaulting
to 100% instead of 50% for the Q5 devices, got ignored as the driver has
never touched them anyway.
The no longer supported "read from cache during block erase"
functionality is not reflected as the current SPI NAND core does not
support it anyway.
Implementation has been tested on MediaTek MT7688 based GARDENA smart
Gateways using both, GigaDevice GD5F1GQ5UEYIG and GD5F1GQ4UBYIG.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Hauke Mehrtens [Thu, 11 Feb 2021 12:05:47 +0000 (13:05 +0100)]
mtd: nand: spi: Only one dummy byte in QUADIO
The datasheet only lists one dummy byte in the 0xEB operation for the
following chips:
* GD5F1GQ4xExxG
* GD5F1GQ4xFxxG
* GD5F1GQ4UAYIG
* GD5F4GQ4UAYIG
Reto Schneider:
- Linux patch ported to U-Boot
- Checked for compatibility with GD5F1GQ4xBxxG
- Fixed operation code in original commit message (0xEH -> 0xEB)
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Sean Anderson [Fri, 5 Feb 2021 04:11:08 +0000 (23:11 -0500)]
mtd: spi-nor-core: Fix typo in documentation
This line should come before the docs for the next function.
Fixes: 7aeedac0153 ("mtd: spi: Port SPI NOR framework from Linux") Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Pratyush Yadav <p.yadav@ti.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sean Anderson [Fri, 5 Feb 2021 04:11:07 +0000 (23:11 -0500)]
cmd: sf: Print error on test failure
The sf test command is used to test spi flashes (and spi masters). Printing
the exact error code is very helpful to those debugging the spi stack.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Pratyush Yadav <p.yadav@ti.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sean Anderson [Fri, 5 Feb 2021 04:11:06 +0000 (23:11 -0500)]
cmd: sf: Display errno on erase failure
If there is an error while erasing SPI flash, no errno is displayed. This
makes it difficult to determine the cause of the error. This change mirrors
the logic for write errors above.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Pratyush Yadav <p.yadav@ti.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Adam Ford [Mon, 18 Jan 2021 21:32:49 +0000 (15:32 -0600)]
spi: nxp_fspi: Fix error reporting
On the i.MX8M Mini, ret = clk_set_rate() sets ret to the value of the
rate the clock was able to set. When checking for errors, it only
checks that it is not NULL. Since positive numbers are not errors,
only check for negative numbers when handling errors.
Fixes: 383fded70c4f ("spi: nxp_fspi: new driver for the FlexSPI controller") Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Pratyush Yadav <p.yadav@ti.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Marek Behún [Fri, 19 Feb 2021 16:11:26 +0000 (17:11 +0100)]
ddr: marvell: a38x: fix comment in conditional macro
The code was processed with unifdef utility to omit portions not
relevant to A38x and DDR3. This removes usage of many macros, including
A70X0, A80X0 and A3900. It seems that the unifdef utility did not remove
the macros from #else comment.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Marek Behún [Fri, 19 Feb 2021 16:11:25 +0000 (17:11 +0100)]
ddr: marvell: a38x: bump version to 14.0.0
Bump version of a38x DDR3 trianing to version 14.0.0 to reflect the
version in the mv-ddr-devel branch of upstream repository
https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git.
There is a new version numbering system, where after 18.12.0 came
1.0.0, 2.0.0, and so on until 14.0.0. So 14.0.0 is newer than 18.12.0.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
@pali suggested this change
In commit 6285efb ("mv_ddr: add support for twin-die combined memory
device") was added support for twin-die combined memory device and
default value for explicitly uninitialized structure members is zero, s
also twin_die_combined is initialized to zero. Which means COMBINED
value.
As prior this commit there was no support for twin-die combined memory
device, default value for twin_die_combined should be NOT_COMBINED. This
change change order of enum mv_ddr_twin_die to ensure that NOT_COMBINED
has value zero.
Signed-off-by: heaterC <airyguy@gmx.de> Signed-off-by: Marek Behún <marek.behun@nic.cz> Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
The funtion returnd cs size in byte instead of MB, that cause
calculation error since the caller was expected to get u32 and when he
got above 4G it refers it as 0.
The fix was to get the cs memory size from function as in MB and then
multiply it by 1MB.
Signed-off-by: Moti Buskila <motib@marvell.com> Reviewed-by: Kostya Porotchkin <kostap@marvell.com> Signed-off-by: Marek Behún <marek.behun@nic.cz> Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
the twin-die combined memory device should be treatened as X8
device and not as X16 one
Signed-off-by: Moti Buskila <motib@marvell.com> Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
[ - the default value for twin_die_combined is set to NOT_COMBINED for
all boards, as this was default behaviour prior this change ] Signed-off-by: Marek Behún <marek.behun@nic.cz> Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
The ODT enable heuristic based on active chip-selects is not always
correct. Some board might use two chip-selects, but have only one ODT
line connected. Allow board specific mv_ddr_topology_map to directly set
the ODT configuration register value.
- function mv_ddr_spd_die_capacity_user_get() has a bug,
since it insert a user memory enum to it,
instead of SPD memory enum (which are different)
- fix: remove mv_ddr_spd_die_capacity_user_get() function.
- memory size with 64 and 32 bit already calculated correctly
at mv_ddr_mem_sz_per_cs_get() function
Signed-off-by: Moti Buskila <motib@marvell.com> Reviewed-by: Stefan Chulski <Stefan.Chulski@cavium.com> Reviewed-by: Alex Leibovich <alexl@marvell.com> Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com> Signed-off-by: Marek Behún <marek.behun@nic.cz> Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
- fix JIRA A7K8K-5056
- remove TEST_PATTERN write at the load patern stage earlier to WL SUP stage
- the WL SUP stage already writes this pattern to the memory, if the pattern exist at the memory
then the algorithm will fail, since it think that there are no phase to correct
Signed-off-by: Moti Buskila <motib@marvell.com> Reviewed-by: Kostya Porotchkin <kostap@marvell.com> Signed-off-by: Marek Behún <marek.behun@nic.cz> Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Marek Behún [Mon, 8 Feb 2021 22:01:41 +0000 (23:01 +0100)]
pci: pci_mvebu: set local dev to number 1
Linux displays the real PCIe card connected to a mvebu PCIe slot as
device 0, not 1. This is done by setting local dev number to 1, so that
the local "Marvell Memory controller" device is on address 1.
Let's do it also in U-Boot.
With this commit the pci command in U-Boot prints something like:
=> pci
Scanning PCI devices on bus 0
BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
00.00.00 0x168c 0x003c Network controller 0x80
Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Stefan Roese <sr@denx.de> Cc: Phil Sutter <phil@nwl.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 8 Feb 2021 22:01:40 +0000 (23:01 +0100)]
pci: pci_mvebu: refactor validation of addresses for config access
Refactor validation of bdf parameter in mvebu_pcie_read/write_config
functions.
We can simplify the code by putting the validation into separate
function.
Also there are always only two devices visible on local bus:
* on slot configured by function mvebu_pcie_set_local_dev_nr()
(by default this register is set to 0) there is a
"Marvell Memory controller", which isn't useful in root complex
mode,
* on all other slots the real PCIe card connected to the PCIe slot.
We can simplify the code even more by simply allowing access only to
the real PCIe card.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Stefan Roese <sr@denx.de> Cc: Phil Sutter <phil@nwl.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 8 Feb 2021 22:01:39 +0000 (23:01 +0100)]
pci: pci_mvebu: debug rd/wr config as other drivers do
Other drivers (aardvark, intel_fpga) print "(addr,size,val)" when
debugging is enabled. Print size for pci_mvebu as well.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Stefan Roese <sr@denx.de> Cc: Phil Sutter <phil@nwl.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 8 Feb 2021 22:01:38 +0000 (23:01 +0100)]
pci: pci_mvebu: cosmetic fix
Write bdf address in a same way in mvebu_pcie_read/write_config.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Stefan Roese <sr@denx.de> Cc: Phil Sutter <phil@nwl.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 8 Feb 2021 22:01:37 +0000 (23:01 +0100)]
pci: pci_mvebu: use dev_seq instead of static variable
PCI uclass maps PCI bus numbers to the seq member of struct udevice.
Use dev_seq(dev) as the bus number in mvebu_pcie_probe instead of an
incrementing a static variable.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Stefan Roese <sr@denx.de> Cc: Phil Sutter <phil@nwl.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Fri, 5 Feb 2021 14:32:28 +0000 (15:32 +0100)]
arm: a37xx: pci: Set Max Payload Size and Max Read Request Size to 512 bytes
Fix usage of VL805 XHCI PCIe controller when it is connected via PCIe to
Armada 3720 SOC. Without this U-Boot crashes when trying to access
enumerated USB devices connected to this XHCI PCIe controller.
This should be done according to the PCIe Link Initialization sequence, as
defined in Marvell Armada 3720 Functional Specification.
Linux has this code too.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
According to the datasheets, all of these 3 types support BP(0,1,2) and
TB bits in the status register (SR), so it could reuse the flash
protection logic for ST Micro.
So it should be safe to add the SPI_NOR_HAS_LOCK and SPI_NOR_HAS_TB
flags to the w25q128 entry of spi_nor_ids table.
Signed-off-by: Su Baocheng <baocheng.su@siemens.com>
[jagan: remove comments in spi-nor-ids.c] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tom Rini [Sun, 21 Feb 2021 01:06:28 +0000 (20:06 -0500)]
ppc: configs: Remove a few non-updated build configurations
In the cases of T2080RDB_SECURE_BOOT, T2080RDB_SRIO_PCIE_BOOT,
P2041RDB_SECURE_BOOT, P2041RDB_SRIO_PCIE_BOOT, P3041DS_SRIO_PCIE_BOOT
and P4080DS_SRIO_PCIE_BOOT while some forms of the board have been
migrated more fully to current build standards, these have not. Remove
them.
common: Add "ifndef __ASSEMBLY__" in asm/global_data.h
Commit "common: Drop asm/global_data.h from common header" added
asm/global_data.h into secure.h. However, secure.h will be included
by psci.S. Adding asm/global_data.h has caused compilation failure in
pcsi.S. Add "ifndef __ASSEMBLY__" in asm/global_data.h.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
When copying to a u32 field we should use sizeof(u32) and not
sizeof(*u32) in memcpy.
On 64bit systems like cortina_presidio-asic-emmc_defconfig using
sizeof(*u32) leads to a buffer overrun.
Fixes: febe13b438b3 ("net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCs") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
dm: ddr: socfpga: don't assign values that are not used
The values of left_edge[0] and right_edge[0] are overwritten before they
are used. Remove the superfluous assignments.
Fixes: 285b3cb939a8 ("dm: ddr: socfpga: fix gen5 ddr driver to not use bss") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Peter Robinson [Thu, 18 Feb 2021 20:06:37 +0000 (20:06 +0000)]
rng: iProc rng200: Rename ..._platdata variables to just ..._plat
In 8a8d24bd Simon dropped data from all the various _platdata calls
but it seems this wasn't caught for the RNG200 driver from when it
was posted to merged. This fixes that issue.
test/cmd/setexpr.c cannot be linked with CONFIG_CMD_SETEXPR=n:
ld.bfd: test/built-in.o: in function `setexpr_test_sub':
test/cmd/setexpr.c:227: undefined reference to `setexpr_regex_sub'
ld.bfd: test/built-in.o: in function `setexpr_test_backref':
test/cmd/setexpr.c:267: undefined reference to `setexpr_regex_sub'
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
In file included from lib/rsa/rsa-keyprop.c:16:
include/u-boot/rsa-mod-exp.h:65:24: warning:
‘struct udevice’ declared inside parameter list will not be visible
outside of this definition or declaration
65 | int rsa_mod_exp(struct udevice *dev, const uint8_t *sig,
| uint32_t sig_len,
| ^~~~~~~
include/u-boot/rsa-mod-exp.h:96:24: warning:
‘struct udevice’ declared inside parameter list will not be visible
outside of this definition or declaration
96 | int (*mod_exp)(struct udevice *dev, const uint8_t *sig,
|
by defining struct udevice.
Fixes: 401d1c4f5d2d ("common: Drop asm/global_data.h from common header") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Matthias Brugger [Tue, 16 Feb 2021 19:54:07 +0000 (20:54 +0100)]
configs: BPI-R2: Disable EFI Grub workaround
The EFI Grub workaround on BananaPi R2 slows down the boot process to
the point, that the watchdog will trigger a reboot before the kernel can
reset it. Fix this by disabeling the workaround.
Vincent Stehlé [Sun, 14 Feb 2021 18:39:04 +0000 (19:39 +0100)]
virtio: fix off by one device id comparison
VIRTIO_ID_MAX_NUM is the largest device ID plus 1. Therefore a device id
cannot be greater or equal to VIRTIO_ID_MAX_NUM. Fix the comparison
accordingly.
Fixes: 8fb49b4c7a82 ("dm: Add a new uclass driver for VirtIO transport devices") Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com>
Roger Pau Monne [Sat, 13 Feb 2021 10:06:32 +0000 (11:06 +0100)]
build/DTC: fix sed usage in DTC command
Current sed usage in the DTC command relies on GNU sed specific -i
option which has a slightly different syntax for BSD sed and always
expects an extension to be provided in order to create a backup file.
Instead drop the cat concatenation done before the sed call and use
sed itself to edit and concatenate the files.
No functional change intended.
Signed-off-by: Roger Pau Monné <royger@FreeBSD.org>
projects / u-boot.git / log