powerpc/t4240qds: Update RCW, defconfig and maintainer
1. board/freescale/t4qds/t4_rcw.cfg
1.8GHz support is requested as default frequency, so update the rcw.
2. remove un-used configs
configs/T4160QDS_SPIFLASH_defconfig
configs/T4240QDS_SPIFLASH_defconfig
SPI boot is not available on T4QDS, so the configs should be removed.
Shengzhou Liu [Wed, 22 Apr 2015 09:54:40 +0000 (17:54 +0800)]
t2080rdb/rcw: update ddr frequency from 1600MT/s to 1867MT/s
T2080RDB RevC uses new SODIMM 1867MT/s instead of previous 1600MT/s.
So update RCW to support new DDR frequency 1867MT/s by default.
Reserve the old 1600MT/s in comment for users in needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Yangbo Lu [Wed, 22 Apr 2015 05:57:56 +0000 (13:57 +0800)]
powerpc/t2080qds: enable eSDHC peripheral clock support
Enable eSDHC peripheral clock support. u-boot and linux will
use SD clock generated by peripheral clock instead of platform
clock.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Reviewed-by: York Sun <yorksun@freescale.com>
Yangbo Lu [Wed, 22 Apr 2015 05:57:40 +0000 (13:57 +0800)]
mmc: fsl_esdhc: Add peripheral clock support
The SD clock could be generated by platform clock or peripheral
clock for some platforms. This patch adds peripheral clock
support for T1024/T1040/T2080. To enable it, define
CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Reviewed-by: York Sun <yorksun@freescale.com>
Yangbo Lu [Wed, 22 Apr 2015 05:57:21 +0000 (13:57 +0800)]
powerpc/t2080qds: enable eSDHC adapter card type identification
Enable eSDHC adapter card type identification and this will do
some corresponding operations and set 'adapter-type' property
for device tree according SDHC Card ID.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Reviewed-by: York Sun <yorksun@freescale.com>
Yangbo Lu [Wed, 22 Apr 2015 05:57:00 +0000 (13:57 +0800)]
mmc: fsl_esdhc: Add adapter card type identification support
Add adapter card type identification support by reading
FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function,
define CONFIG_FSL_ESDHC_ADAPTER_IDENT.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
[York Sun: resolve conflicts in README.fsl-esdhc] Reviewed-by: York Sun <yorksun@freescale.com>
fsl/deepsleep: avoid the DDR restore from being optimized out
Function dp_ddr_restore is to restore the first 128-byte space
of DDR. However those codes may be optimized out by compiler
since the destination address is at 0x0. In order to avoid
compiler optimization, we restore the space from high address,
which is not at 0x0, to low address.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Scott Wood [Fri, 17 Apr 2015 23:10:06 +0000 (18:10 -0500)]
powerpc/mpc85xx: Don't deref NULL if qman portal lacks cell-index
Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Madalin-Cristian Bucur <madalin.bucur@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
This patch defines the 2 flush_dcache_range and invalidate_dcache_range
functions for all the powerpc architecture. Their implementation is
borrowed from the kernel's misc_32.S file and replace the ones from
mpc86xx and ppc4xx since they were equivalent.
This is a fix for the problem introduced by this patch:
http://patchwork.ozlabs.org/patch/448849/
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shengzhou Liu [Fri, 27 Mar 2015 07:48:34 +0000 (15:48 +0800)]
powerpc/t1023rdb: Add T1023 RDB board support
T1023RDB is a Freescale Reference Design Board that hosts the T1023 SoC.
T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- one 1G RGMII port on-board(RTL8211F PHY)
- one 1G SGMII port on-board(RTL8211F PHY)
- one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR: 128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash.
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC card and eMMC on-board
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339 on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging
As well updated T1024RDB to add T1023RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix defconfig files] Reviewed-by: York Sun <yorksun@freescale.com>
Minghuan Lian [Fri, 27 Mar 2015 05:24:39 +0000 (13:24 +0800)]
fsl/pci: Set CFG_READY for PCIe v3.0 and later
Freescale PCIe controllers v3.0 and later need to set bit
CFG_READY to allow all inbound configuration transactions
to be processed normally when in EP mode. However, bit
CFG_READY has been moved from PCIe configuration space to
CCSR PCIe configuration register comparing previous version.
The patch is to set this bit according to PCIe version.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Chunhe Lan [Fri, 20 Mar 2015 09:08:54 +0000 (17:08 +0800)]
powerpc/t4rdb: Add SD boot support for T4240RDB board
This patch adds SD boot support for T4240RDB board. SPL
framework is used. PBL initializes the internal RAM and
copies SPL to it. Then SPL initializes DDR using SPD and
copies u-boot from SD card to DDR, finally SPL transfers
control to u-boot.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: Fix T4240RDB_SDCARD_defcofig] Reviewed-by: York Sun <yorksun@freescale.com>
Add a delay of 1 microsecond before issuing soft reset to the
controller to let ongoing ULPI transaction complete.
This prevents corruption of ULPI Function Control Register which
eventually prevents phy clock from entering to low power mode
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Scott Wood [Fri, 24 Apr 2015 01:01:56 +0000 (20:01 -0500)]
powerpc/mpc85xx: Use GOT when loading IVORs post-relocation
Commit 96d2bb952bb ("powerpc/mpc85xx: Don't relocate exception vectors")
simplified IVOR initialization a bit too much, failing to use the
post-relocation offset. This doesn't cause a problem with normal NOR
boot, in which both the pre-relocation and post-relocation addresses
are 64 KiB aligned. However, if TEXT_BASE is only 4 KiB aligned, such
as for NAND/SD/etc. boot on some targets, as well as the QEMU target,
the post-relocation address will not be the same in the lower 16 bits,
as reserve_uboot() ensures that the relocation address is always 64
KiB aligned even if the pre-relocation address was not.
Use the GOT to get the proper post-relocation offsets.
Fixes: 96d2bb952bb ("powerpc/mpc85xx: Don't relocate exception vectors") Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Alexander Graf <agraf@suse.de> Cc: Shaohui Xie <Shaohui.Xie@freescale.com> Tested-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Masahiro Yamada [Mon, 16 Mar 2015 07:43:21 +0000 (16:43 +0900)]
ARM: zynq: pass "-mfpu=neon" only to lowlevel_init.S
The comment line in arch/arm/cpu/armv7/zynq/config.mk says that
the option "-mfpu=neon" is necessary for compiling lowlevel_init.S.
We do not have to give it to all the source files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Disable all level shifters before enabling
the PS-to-PL level shifters as it would
be good to disable all level shifters before
enabling the PS-to-PL in order to ensure that
it is in proper state
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We are about to change the location for ps7_init files, breaking the
current work-flows. It is good time to drop the legacy ps7_init.c/h
support.
Going forward, please use ps7_init_gpl.c/h all the time.
If you are still using old Xilinx tools that are only able to
generate ps7_init.c/h, rename them into ps7_init_gpl.c/h.
The PicoZed is a System-on-Module board which is marketed as part of
the ZedBoard/MicroZed/etc. collection. It includes a Zynq-7000
processor.
This patch adds support that covers all the variants of the PicoZed
including the SKUs with Z7010/Z7020 and Z7015/Z7030 Zynq chips. This
patch set however only covers support for the System-on-Module and does
not cover any extra components that are available on carrier boards
(except those that are fanned out of the module itself).
More information on this board, its variants and available carrier
boards is available at: http://zedboard.org/product/picozed
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is possible for CONFIG_XILINX_EMACLITE to be defined without
XILINX_EMACLITE_BASEADDR being defined as the EMAC Lite driver support
OF init. Check that the driver is enabled and the base address is
available before initializing with a static base address.
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Simon Glass [Sat, 25 Apr 2015 04:33:07 +0000 (22:33 -0600)]
dm: core: Correct bug introduced in uclass_first/next_device()
These functions now rely on uclass_find_first/next_device() and assume that
they will either return failure (-ve error code) or a device. In fact,
coming to the end of a list is not considered failure and they return 0
in that case.
The logic to deal with this was replaced in commit acb9ca2a with just using
uclass_get_device_tail(). Add back the missing logic. This bug was
caught by unit tests but since they were broken for other reasons at the
time, this was not noticed.
Upto now flash sector_size is assigned from params which isn't
necessarily a sector size from vendor, so based on the SECT_*
flags from flash_params the erase_size will compute and it will
become the sector_size finally.
Bug report (from Bin Meng):
=> sf probe
SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB,
total 2 MiB, mapped at ffe00000
=> sf erase 0 +100
SF: 65536 bytes @ 0x0 Erased: OK
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Reported-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Fri, 24 Apr 2015 11:51:10 +0000 (19:51 +0800)]
dm: sf: Make SST flash write op work again
With SPI flash moving to driver model, commit fbb0991 "dm: Convert
spi_flash_probe() and 'sf probe' to use driver model" ignored the
SST flash-specific write op (byte program & word program), which
actually broke the SST flash from wroking.
This commit makes SST flash work again under driver model, by adding
SST flash-specific handling in the spi_flash_std_write().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
David Dueck [Wed, 1 Apr 2015 12:20:24 +0000 (14:20 +0200)]
spi: omap3: Fix timeout handling
The timeout value is never reset during the transfer. This means that when
transferring more data we eventually trigger the timeout.
This was reported on the mailing list:
"Spansion SPI flash read timeout with AM335x"
Signed-off-by: David Dueck <davidcdueck@googlemail.com> CC: Tom Rini <trini@konsulko.com> CC: Stefan Roese <sr@denx.de> CC: Andy Pont <andy.pont@sdcsystems.com> Tested-by: David Dueck <davidcdueck@googlemail.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cubox-i and Hummingboard support several MX6 SoCs: mx6solo, mx6dual-lite,
mx6dual and mx6quad. Add support for the different SoC/memory sizes
combinations.
DDR initialization values were extracted from Solid-run internal U-boot.
Tested on a CuBox-i4Pro, HummingBoard-i2eX and HummingBoard-i1.
MIPS: implement device-tree handover to Linux kernel
Add device-tree handover to Linux kernel conforming with MIPS UHI [1].
Register $a0 will be set to the reserved value -2. The address of
the device-tree blob will be stored as KSEG0 address in $a1. $a2 and
$a3 are set to zero.
Hans de Goede [Mon, 20 Apr 2015 09:13:37 +0000 (11:13 +0200)]
fdt: Fix handling of paths with options in them
After syncing the sunxi dts files with the upstream kernel dm/fdt sunxi
builds would no longer boot.
The problem is that stdout-path is now set like this in the upstream dts
files: stdout-path = "serial0:115200n8". The use of options in of-paths,
either after an alias name, or after a full path, e.g. stdout-path =
"/soc@01c00000/serial@01c28000:115200", is standard of usage, but something
which the u-boot dts code so far did not handle.
This commit fixes this, adding support for both path formats.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Simon Glass <sjg@chromium.org>
Scott Wood [Tue, 24 Mar 2015 20:25:03 +0000 (13:25 -0700)]
armv8/ls2085ardb: Enable NAND SPL support
Enable NAND boot support using SPL framework. To boot from
NAND, either use DIP switches on board, or "qixis_reset nand"
command. Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872] Signed-off-by: York Sun <yorksun@freescale.com>
Scott Wood [Tue, 24 Mar 2015 20:25:02 +0000 (13:25 -0700)]
armv8/ls2085aqds: NAND boot support
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872] Signed-off-by: York Sun <yorksun@freescale.com>
Jaiprakash Singh [Sat, 21 Mar 2015 02:28:27 +0000 (19:28 -0700)]
driver/ifc: Add 64KB page support
IFC has two register pages.Till IFC version 1.4 each
register page is 4KB each.But IFC ver 2.0 register page
size is 64KB each.IFC regiters structure is break into
two viz FCM and RUNTIME.FCM(Flash control machine) registers
are defined in PAGE0 and controls IFC generic functionality.
RUNTIME registers are defined in PAGE1 and controls NAND and
GPCM funcinality.
FCM and RUNTIME structures defination is common for IFC
version 1.4 and 2.0.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
ARM: vf610: Initial integration for Colibri VF50/VF61
This adds initial support for Colibri VF50/VF61 based on Freescale
Vybrid SoC.
- CPU clocked at 396/500 MHz
- DDR3 at 396MHz
- for VF50, use PLL2 as memory clock (synchronous mode)
- for VF61, use PLL1 as memory clock (asynchronous mode)
- Console on UART0 (Colibri UART_A)
- Ethernet on FEC1
- PLL5 based RMII clocking (E.g. No external crystal)
- UART_A and UART_C I/O muxing
- Boot from NAND by default
Tested on Colibri VF50/VF61 booting using serial loader over UART.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> Acked-by: Stefan Agner <stefan@agner.ch>
Vybrid product family consists of several rather similar SoC which
can be determined by softare during boot time. This allows use of
variable ${soc} for Linux device tree files. Detect VF5xx CPU's by
reading the CPU count register. We can determine the second number
of the CPU type (VF6x0) which indicates the presence of a L2 cache.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
ARM: vf610: Move DDR3 initialization to imx-common
In order to avoid code duplication, move the DDR3 initialization to the
common place under imx-common. Currently ROW_DIFF and COL_DIFF can be
chosen from the board file. The JEDEC timings are specified using a
common ddr3_jedec_timings structure.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Marek Vasut [Thu, 9 Apr 2015 23:11:54 +0000 (01:11 +0200)]
rtc: Set valid date after reset
Some RTC chips tend to set garbage date after reset.
This patch sets the date to 2000-01-01 00:00 immediatelly
after the RTC chip reset is issued using the "date reset"
command.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@konsulko.com>
Dileep Katta [Fri, 27 Mar 2015 17:36:57 +0000 (23:06 +0530)]
fastboot: ARM: OMAP5: Enable reboot-bootloader
Implemented fb_set_reboot_flag() for OMAP5 to set
an environment variable 'dofastboot' when reboot-bootloader called.
This environment variable will be checked in boot command and fastboot
will be called if the variable is set.
If the bootcmd env variable of OMAP5 common is overwritten with board-specific
command, then these changes will not apply.
This was originally intended for DRA7 platform, but now applies to all OMAP5.
Signed-off-by: Angela Stegmaier <angelabaker@ti.com> Signed-off-by: Dileep Katta <dileep.katta@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Make it check for !CONFIG_ENV_IS_NOWHERE as we can't saveenv()
in that case] Signed-off-by: Tom Rini <trini@konsulko.com>
patman: check git format.subjectprefix setting when generate patches prefix
For the local project, we may specified format.subjectprefix setting.
Then the patch will be formated as [Project_prefix][PATCH].
But patman will not check this setting. It will remove the
format.subjectprefix.
So This patch will let patman check this setting and add it as a
project prefix.
Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Michal Simek [Mon, 20 Apr 2015 09:46:24 +0000 (11:46 +0200)]
buildman: Add gcc 4.9.0 with Microblaze toolchain
Also read gcc 4.9.0 at kernel.org which also have Microblaze toolchain.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Fixed unit test failure by updating the test: Signed-off-by: Simon Glass <sjg@chromium.org>
Dileep Katta [Tue, 24 Mar 2015 22:34:50 +0000 (04:04 +0530)]
ARM: DRA7XX: Enable Fastboot
- Fastboot is enable by default for DRA7XX
- This is based on following patch modified accordingly
http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=b2e04f92b5d91c708b6fd6b79d2266966ac51f4b
Signed-off-by: Angela Stegmaier <angelabaker@ti.com> Signed-off-by: Dileep Katta <dileep.katta@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Xiang Wang [Mon, 23 Mar 2015 22:56:58 +0000 (17:56 -0500)]
gpio: mvmfp: support newer MFP bit definitions
1. The bits 11..10 for mfp driver strength is only valid for
aspen and old xscale family, for newer Marvell chip, this range
has been moved to 12..11.
2. add sleep bit support
Signed-off-by: Xiang Wang <wangx@marvell.com>
[robh: rebase to current mainline] Signed-off-by: Rob Herring <robh@kernel.org>
Peter Howard [Sun, 22 Mar 2015 22:19:56 +0000 (09:19 +1100)]
davinci: add support for omapl138-lcdk board
Signed-off-by: Peter Howard <phoward@gme.net.au>
[trini: Add config file, update for ..._ether_addr() -> ..._ethaddr() rename] Signed-off-by: Tom Rini <trini@konsulko.com>
driver/ldpaa: Add support of WRIOP static data structure
Wire rate IO Processor (WRIOP) provide support of receive and transmit
ethernet frames from the ethernet MAC. Here Each WRIOP block supports
upto 64 DPMACs.
Create a house keeping data structure to support upto 16 DPMACs and
store external phy related information.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
Shaohui Xie [Sat, 21 Mar 2015 02:28:19 +0000 (19:28 -0700)]
net/memac_phy: reuse driver for little endian SoCs
The memac for PHY management on little endian SoCs is similar on big
endian SoCs, so we modify the driver by using I/O accessor function to
handle the endianness, so the driver can be reused on little endian
SoCs, we introduce CONFIG_SYS_MEMAC_LITTLE_ENDIAN for little endian
SoCs, if the CONFIG_SYS_MEMAC_LITTLE_ENDIAN is defined, the I/O access
is little endian, if not, the I/O access is big endian. Move fsl_memac.h
out of powerpc include.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
J. German Rivera [Sat, 21 Mar 2015 02:28:18 +0000 (19:28 -0700)]
drivers/fsl-mc: Changed MC firmware loading for new boot architecture
Changed MC firmware loading to comply with the new MC boot architecture.
Flush D-cache hierarchy after loading MC images. Add environment
variables "mcboottimeout" for MC boot timeout in milliseconds,
"mcmemsize" for MC DRAM block size. Check MC boot status before calling
flib functions.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
projects / u-boot.git / log