doc: imx: habv4: Add Secure Boot guide for i.MX6 and i.MX7 non-SPL targets
Add HABv4 documentation for non-SPL targets covering the
following topics:
- How to sign an securely boot an u-boot-dtb.imx image.
- How to extend the root of trust for additional boot images.
- Add 3 CSF examples.
- Add IVT generation script example.
Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Utkarsh Gupta <utkarsh.gupta@nxp.com> Signed-off-by: Breno Lima <breno.lima@nxp.com>
Adam Ford [Thu, 17 Jan 2019 13:16:39 +0000 (07:16 -0600)]
MTD: nand: mxs_nand: Allow driver to auto setup ECC in SPL
The initialization of the NAND in SPL hard-coded ecc.bytes,
ecc.size, and ecc.strength which may work for some NAND parts,
but it not appropriate for others. With the pending patch
"mxs_nand: Fix BCH read timeout error on boards requiring ECC"
the driver can auto configure the ECC when these entries are
blank. This patch has been tested in NAND flash with oob 64
and oob 128.
Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Jörg Krause <joerg.krause@embedded.rocks> Acked-by: Tim Harvey <tharvey@gateworks.com> Tested-by: Tim Harvey <tharvey@gateworks.com>
Adam Ford [Tue, 15 Jan 2019 17:26:48 +0000 (11:26 -0600)]
net: dm: fec: Fix regulator enable when using DM_REGULATOR
When DM_REGULATOR is enabled, the driver attempts to call
regulator_autoset() which expects the regulators to be on at boot
and/or always on and fails if they are not true.
For a more generic approach, this patch just calls
regulator_set_enable() which shouldn't have such restrictions.
Fixes: ad8c43cbcafb ("net: dm: fec: Support the phy-supply
binding")
Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Martin Fuzzey <martin.fuzzey@flowbird.group> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adam Ford [Sat, 12 Jan 2019 23:32:00 +0000 (17:32 -0600)]
ARM: imx6q_logic: Correct phy fixup for broken ethernet
The Ethernet has been broken for some time. This patch unifies
this board with a few others that use a similar approach to
enabling phy. This fixes ar8031 Ethernet controller so it works.
The LogicPD board uses a Micron Flash with ECC. To boot this from
SPL, the ECC needs to be correctly configured or the BCH engine
times out.
Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Stefan Agner <stefan.agner@toradex.com> Tested-by: Jörg Krause <joerg.krause@embedded.rocks> Acked-by: Tim Harvey <tharvey@gateworks.com> Tested-by: Tim Harvey <tharvey@gateworks.com>
Tom Rini [Wed, 13 Feb 2019 12:12:29 +0000 (07:12 -0500)]
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2019-02-13
Goodness this time around:
- HII protocol, finally allows us to run the UEFI Shell!
(experimantal, disabled by default)
- efi selftest now available on Cortex-M
- NVMe support for distro boot
- Lots of code cleanup
We check the existence of files with fs_exist(). This function calls
fs_close(). If we do not set the active block device again fs_opendir()
fails and we do not set the flag EFI_FILE_DIRECTORY. Due to this error the
`cd` command in the EFI shell fails.
So let's add the missing set_blk_dev(fh) call.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Mon, 11 Feb 2019 14:24:00 +0000 (15:24 +0100)]
efi_loader: Make HII a config option
Heinrich ran into issues with HII and iPXE which lead to #SErrors on
his Odroid-C2 system. We definitely do not want to regress just yet,
so let's not expose the HII protocols by default.
Instead, let's make it a config option that people can play with
This way, we can stabilize the code in tree without breaking any
users.
Once someone figures out, why this breaks iPXE (probably a NULL
dereference), we can enable it by default.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
---
Alexander Graf [Mon, 11 Feb 2019 14:07:17 +0000 (15:07 +0100)]
arm: Leave smccc calls in .text when efi_loader=n
Commit 81ea00838c6 ("efi_loader: PSCI reset and shutdown") put the SMCCC
assembly code into the efi specific code section. This is wrong when we
do not have EFI_LOADER enabled, as that strips efi runtime sections from
the output binary
Reported-by: Michal Simek <monstr@monstr.eu> Reported-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Tested-by: Michal Simek <monstr@monstr.eu> Fixes: 81ea00838c6 ("efi_loader: PSCI reset and shutdown") Signed-off-by: Alexander Graf <agraf@suse.de>
efi_st_printf() does not support format code %ld. Anyway the format code
for size_t would be %zu which isn't supported either.
We do not want any divisions to avoid invalid references to integer
arithmetic routines, cf.
https://gcc.gnu.org/onlinedocs/gccint/Integer-library-routines.html.
As a simple remedy remove the noisy messages from the output.
They are not relevant for automated testing.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
AKASHI Takahiro [Mon, 21 Jan 2019 03:12:59 +0000 (12:12 +0900)]
efi: hii: add keyboard layout package support
Allow for handling keyboard layout package in HII database protocol.
A package can be added or deleted in HII database protocol, but
we don't set 'current' keyboard layout as there is no driver that
requests a keyboard layout.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
HII database protocol in this patch series can handle only:
* GUID package
* string package
* keyboard layout package
(The other packages, except Device path package, will be necessary
for interactive and graphical UI.)
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org> Signed-off-by: Rob Clark <robdclark@gmail.com> Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
Our current implementation of GetNextVariableName() first collects all EFI
variables. If none is found at all hexport_r() returns a zero length string
terminated by \0 and the value 1 as number of bytes in the returned buffer.
In this case GetNextVariableName() has to return EFI_NOT_FOUND.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Symbolic links are not supported on all file systems, e.g. not on FAT. So
it is not wise to use them in our source tree.
Use a qualified path to refer to lib/efi_loader/efi_freestanding.c in
scripts/Makefile.lib instead.
Reported-by: Alexander Graf <agraf@suse.de> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: Fix build with O=] Signed-off-by: Alexander Graf <agraf@suse.de>
AKASHI Takahiro [Mon, 21 Jan 2019 11:43:14 +0000 (12:43 +0100)]
efi_selftest: fix variables test for GetNextVariableName()
There is a bug in efi variables test.
Fix it with some cosmetic improvements.
Please note that efi variables test still fails at QueryVariableInfo()
and GetVariable(), but this is not due to a change in this patch.
==8<==
Testing EFI API implementation
Selected test: 'variables'
Setting up 'variables'
Setting up 'variables' succeeded
Executing 'variables'
.../u-boot/lib/efi_selftest/efi_selftest_variables.c(60):
TODO: QueryVariableInfo failed
.../u-boot/lib/efi_selftest/efi_selftest_variables.c(131):
TODO: GetVariable returned wrong length 7
.../u-boot/lib/efi_selftest/efi_selftest_variables.c(133):
TODO: GetVariable returned wrong value
Executing 'variables' succeeded
Boot services terminated
Summary: 0 failures
==>8==
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
AKASHI Takahiro [Mon, 21 Jan 2019 11:43:13 +0000 (12:43 +0100)]
efi_loader: implement GetNextVariableName()
The current GetNextVariableName() is a placeholder.
With this patch, it works well as expected.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
rebased on efi-next Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Stating the function module is sufficient. We don't need file and line
number. Anyway the format code for the line number was incorrect (should
be %d).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Running the simple network protocol test on the sandbox requires setting
the environment variable ethact to a network interface connected to a DHCP
server and ethrotate to 'no'. So let's make it an on-request test on the
sandbox (selectable by setting environment variable efi_selftest).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
AKASHI Takahiro [Sun, 30 Dec 2018 14:16:55 +0000 (15:16 +0100)]
efi_loader: move efi_init_obj_list() to a new efi_setup.c
The function, efi_init_obj_list(), can be shared in different pseudo efi
applications, like bootefi/bootmgr as well as my efishell. Moreover, it
will be utilized to extend efi initialization, for example, my "removable
disk support" patch and "capsule-on-disk support" patch in the future.
So with this patch, it will be moved to a new file, efi_setup.c, under
lib/efi_loader and exported, making no changes in functionality.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Remove lines deactivated by #if 1 #else Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
ARMv7-M only supports the Thumb instruction set. Our current crt0 code does
not support it. With the patch we can build all unit tests of the EFI
subsystem that do not require crt0.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 7b78d6438a2b ("efi_loader: Reserve unaccessible memory") introduced
a comparison between RAM top and RAM start that was not known at the time
when the patch of commit 49759743bf09 ("efi_loader: eliminate sandbox
addresses") was written.
The sandbox uses an address space that is only relevant in the sandbox
context. We have to map ram_top from the sandbox address space to the
physical address space before using it in the EFI subsystem.
Fixes: 49759743bf09 ("efi_loader: eliminate sandbox addresses") Fixes: 7b78d6438a2b ("efi_loader: Reserve unaccessible memory") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
It should not be necessary to adjust CMD_BOOTEFI_HELLO_COMPILE in config
files.
arch/arm/lib/crt0_arm_efi.S cannot be compiled in thumbs mode. We can
disable CMD_BOOTEFI_HELLO_COMPILE for CONFIG_CPU_V7M. So there is no longer
a need to disable it in stm32 configs.
helloworld.efi can be built without problems on x86_64. So there is no need
to disable it in chromebook_link64_defconfig and qemu-x86_64_defconfig.
Same is true for ARM V7A. So do not disable CMD_BOOTEFI_HELLO_COMPILE in
kp_imx6q_tpc_defconfig.
Some architecture checks are already make for EFI_LOADER. There is no need
to repeat them for CMD_BOOTEFI_HELLO_COMPILE
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Patrice.Chotard@st.com Signed-off-by: Alexander Graf <agraf@suse.de>
AKASHI Takahiro [Tue, 4 Dec 2018 06:46:55 +0000 (15:46 +0900)]
distro: not taint environment variables if possible
The aim of this patch is not to have temporary variables used in
distro_bootcmd left as environment variables after run something.
See the discussion[1].
Without this patch, saveenv command also saves those variables, too.
While they are apparently safe, scsi_need_init can be harmful.
Please note that, in most cases, a variable should be converted to
hush's local variable, while "devplist" cannot because it is created
by "part" command as an environment variable.
Commit 393fccdf6c73 ("efi_loader: efi_guid_t must be 64-bit aligned")
has changed the alignment of efi_guid_t. This changed the size of
struct efi_configuration_table on 32-bit systems form 20 to 24 bytes. As
an array of this type is pointed to by the system table this breaks
compatibility with existing versions of GRUB and Linux. Let's get back the
original size by using the attribute __packed.
Fixes: 393fccdf6c73 ("efi_loader: efi_guid_t must be 64-bit aligned") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
On x86_64 the size of the file u-boot loaded by the tftp test has grown in
size such that when loading the file to 0x200000 it overwrites a memory
area reserved for PCI.
If no load address is specified for tftp do not use the ram base address
(or if zero 0x200000) but the default address.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Tue, 12 Feb 2019 12:16:46 +0000 (07:16 -0500)]
Merge git://git.denx.de/u-boot-x86
- Edison switch to CONFIG_OF_SEPARATE.
- Tangier initial ACPI support for PMIC device.
- TSC timer driver update to support native calibration.
- Fixes to 64-bit U-Boot proper.
Bin Meng [Thu, 31 Jan 2019 16:22:14 +0000 (08:22 -0800)]
x86: Use the existing GDT in the ROM for 64-bit U-Boot proper
It is unnecessary to use a RAM version GDT for 64-bit U-Boot proper.
In fact we can just use the ROM version directly, which not only
eliminates the risk of being overwritten by application, but also
removes the complexity of patching the cpu_call64().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 31 Jan 2019 16:22:13 +0000 (08:22 -0800)]
x86: Don't copy the cpu_call64() function to a hardcoded address
Before jumping to 64-bit U-Boot proper, SPL copies the cpu_call64()
function to a hardcoded address 0x3000000. This can have potential
conflicts with application usage. Switch the destination address
to be allocated from the heap to avoid such risk.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 31 Jan 2019 16:22:12 +0000 (08:22 -0800)]
x86: Change 4-level page table base address to low memory
At present the 4-level page table base address for 64-bit U-Boot
proper is assigned an address that conflicts with CONFIG_LOADADDR.
Change it to an address within the low memory range instead.
Fixes crashes seen when 'dhcp' on QEMU x86_64 with
"-net nic -net user,tftp=.,bootfile=u-boot".
Reported-by: Alexander Graf <agraf@suse.de> Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
x86: tsc: Add support for native calibration of TSC freq
Add native tsc calibration function. Calibrate the tsc timer the same
way as linux does in arch/x86/kernel/tsc.c.
Fixes booting for Apollo Lake processors.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Chris Packham [Mon, 11 Feb 2019 01:19:56 +0000 (14:19 +1300)]
ARM: mvebu: x530: use MV_DDR_FREQ_SAR
MV_DDR_FREQ_SAR lets the DDR frequency be determined by hardware
strapping. This also has the side effect of running the DDR clock in
synchronous mode with the CPU core clock rather than from an independent
PLL. We've seen this improve reliability in operation across a number of
boards and temperature ranges.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Baruch Siach [Thu, 7 Feb 2019 11:21:16 +0000 (13:21 +0200)]
Kconfig: fix BUILD_TARGET for ARCH_MVEBU
Commit dc146ca11187 ("Kconfig: Migrate CONFIG_BUILD_TARGET") made the
mvebu default build target depend on CONFIG_SPL_BUILD. Unfortunately,
there is no such Kconfig symbol. Use the CONFIG_SPL symbol instead to
fix that.
Cc: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Stefan Roese <sr@denx.de>
The dm_gpio_set_value() routine sets signal logical level, with
GPIO_ACTIVE_LOW/HIGH value taken into account. Reset active value is 1
(asserted), while reset inactive value is 0 (de-asserted). Fix the reset
toggle code to set the correct reset logic value.
Reported-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Michal Simek [Thu, 31 Jan 2019 15:31:03 +0000 (16:31 +0100)]
i2c: mux: Generate longer i2c mux name
For !DM case busses are listed as
ZynqMP> i2c bus
Bus 0: zynq_0
Bus 1: zynq_0->PCA9544A@0x75:0
Bus 2: zynq_0->PCA9544A@0x75:1
Bus 3: zynq_0->PCA9544A@0x75:2
Bus 4: zynq_1
Bus 5: zynq_1->PCA9548@0x74:0
Bus 6: zynq_1->PCA9548@0x74:1
Bus 7: zynq_1->PCA9548@0x74:2
Bus 8: zynq_1->PCA9548@0x74:3
Bus 9: zynq_1->PCA9548@0x74:4
Bus 10: zynq_1->PCA9548@0x75:0
Bus 11: zynq_1->PCA9548@0x75:1
Bus 12: zynq_1->PCA9548@0x75:2
Bus 13: zynq_1->PCA9548@0x75:3
Bus 14: zynq_1->PCA9548@0x75:4
Bus 15: zynq_1->PCA9548@0x75:5
Bus 16: zynq_1->PCA9548@0x75:6
Bus 17: zynq_1->PCA9548@0x75:7
where is exactly describing i2c bus topology.
By moving to DM case i2c mux buses are using names from DT and because
i2c-muxes describing sub busses with the same names like i2c@0, etc it
is hard to identify which bus is where.
Linux is adding topology information to i2c-mux busses to identify them
better.
This patch is doing the same and composing bus name with topology
information.
When patch is applied with topology information on zcu102-revA.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@ff020000->i2c-mux@75->i2c@0
Bus 3: i2c@ff020000->i2c-mux@75->i2c@1
Bus 4: i2c@ff020000->i2c-mux@75->i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@ff030000->i2c-mux@74->i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@ff030000->i2c-mux@74->i2c@1
Bus 7: i2c@ff030000->i2c-mux@74->i2c@2
Bus 8: i2c@ff030000->i2c-mux@74->i2c@3
Bus 9: i2c@ff030000->i2c-mux@74->i2c@4
Bus 10: i2c@ff030000->i2c-mux@75->i2c@0
Bus 11: i2c@ff030000->i2c-mux@75->i2c@1
Bus 12: i2c@ff030000->i2c-mux@75->i2c@2
Bus 13: i2c@ff030000->i2c-mux@75->i2c@3
Bus 14: i2c@ff030000->i2c-mux@75->i2c@4
Bus 15: i2c@ff030000->i2c-mux@75->i2c@5
Bus 16: i2c@ff030000->i2c-mux@75->i2c@6
Bus 17: i2c@ff030000->i2c-mux@75->i2c@7
Behavior before the patch is applied.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@0
Bus 3: i2c@1
Bus 4: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@1
Bus 7: i2c@2
Bus 8: i2c@3
Bus 9: i2c@4
Bus 10: i2c@0
Bus 11: i2c@1
Bus 12: i2c@2
Bus 13: i2c@3
Bus 14: i2c@4
Bus 15: i2c@5
Bus 16: i2c@6
Bus 17: i2c@7
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
Michal Simek [Thu, 31 Jan 2019 15:31:02 +0000 (16:31 +0100)]
i2c: Fill req_seq in i2c_post_bind()
For i2c controllers which are missing alias in DT there is no req_seq
setup. This function is setting up proper ID based on highest found
alias ID.
On zcu102 this is the behavior when patch is applied.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@0
Bus 3: i2c@1
Bus 4: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@1
Bus 7: i2c@2
Bus 8: i2c@3
Bus 9: i2c@4
Bus 10: i2c@0
Bus 11: i2c@1
Bus 12: i2c@2
Bus 13: i2c@3
Bus 14: i2c@4
Bus 15: i2c@5
Bus 16: i2c@6
Bus 17: i2c@7
Before this patch applied (controllers have -1 ID)
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus -1: i2c@0
Bus -1: i2c@1
Bus -1: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus -1: i2c@0 (active 0)
54: eeprom@54, offset len 1, flags 0
Bus -1: i2c@1
Bus -1: i2c@2
Bus -1: i2c@3
Bus -1: i2c@4
Bus -1: i2c@0
Bus -1: i2c@1
Bus -1: i2c@2
Bus -1: i2c@3
Bus -1: i2c@4
Bus -1: i2c@5
Bus -1: i2c@6
Bus -1: i2c@7
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Michal Simek [Thu, 31 Jan 2019 15:31:01 +0000 (16:31 +0100)]
i2c: dm: Record maximum id of devices before probing devices
There is a need to find out the first free i2c ID which can be used for
i2s buses (including i2c buses connected to i2c mux). Do it early in
init and share this variable with other i2c classes for uniq bus
identification.
add from hs:
fix build problem in i2c-uclass.c for omap devices
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Tom Rini [Sun, 10 Feb 2019 13:04:53 +0000 (08:04 -0500)]
Merge branch '2019-02-08-master-imports'
- bcm6345 watchdog, bcm63158/bcm963158 initial support.
- Various TI platform resyncs and improvements.
- FDT support in Android-format images.
- stm32mp1 improvements.
Simon Glass [Thu, 27 Dec 2018 20:24:36 +0000 (13:24 -0700)]
misc: Allow child devices
Allow misc devices to have children, so that we can use this uclass for
cases where a child device (e.g. I2S) needs to access a misc driver for
transferring data.
Lokesh Vutla [Fri, 11 Jan 2019 09:45:52 +0000 (15:15 +0530)]
mmc: omap_hsmmc: Use regulator_set_enable_if_allowed for enabling regulator
Use regulator_set_enable_if_allowed() api instead of regulator_set_enable()
while enabling io regulators. This way the driver doesn't see an error
when disabling an always-on regulator and when enabling is not supported.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Fri, 11 Jan 2019 09:45:51 +0000 (15:15 +0530)]
power: regulator: Introduce regulator_set_enable_if_allowed api
regulator_set_enable() api throws an error in the following three cases:
- when requested to disable an always-on regulator
- when set_enable() ops not provided by regulator driver
- when enabling is actually failed.(Error returned by the regulator driver)
Sometimes consumer drivers doesn't want to track the first two scenarios
and just need to worry about the case where enabling is actually failed.
But it is also a good practice to have an error value returned in the
first two cases.
So introduce an api regulator_set_enable_if_allowed() which ignores the
first two error cases and returns an error as given by regulator driver.
Consumer drivers can use this api need not worry about the first two
error conditions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log