This patch adds support for the National LM64 temperature
sensor with integrated fan control to lm63.c.
Main difference between LM63 and LM64 is 16°C offset in sensor
readings.
François Revol [Fri, 18 Mar 2011 11:03:03 +0000 (11:03 +0000)]
Fix building tools alone with host compiler
- don't include config.h when building with host cc,
- HOSTCFLAGS was defined with the wrong name, so wasn't used,
- make sure make finds sources outside of tools/.
Luca Ceresoli [Wed, 4 May 2011 02:40:46 +0000 (02:40 +0000)]
net/net.c: cosmetic: fix indentation
This removes the following checkpatch issues:
- ERROR: switch and case should be at the same indent
- WARNING: suspect code indent for conditional statements
- WARNING: labels should not be indented
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Wolfgang Denk <wd@denx.de> Cc: Ben Warren <biggerbadderben@gmail.com>
Luca Ceresoli [Wed, 4 May 2011 02:40:43 +0000 (02:40 +0000)]
net/net.c: cosmetic: fix brace issues
This removes the following checkpatch issues:
- WARNING: braces {} are not necessary for single statement blocks
- WARNING: braces {} are not necessary for any arm of this statement
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Wolfgang Denk <wd@denx.de> Cc: Ben Warren <biggerbadderben@gmail.com>
Luca Ceresoli [Wed, 11 May 2011 03:59:56 +0000 (03:59 +0000)]
net/net.c: cosmetic: fix whitespace issues
This removes the following checkpatch issues:
- ERROR: space prohibited after that open parenthesis '('
- ERROR: space prohibited before that close parenthesis ')'
- ERROR: space prohibited after that open square bracket '['
- ERROR: space prohibited after that '&' (ctx:WxW)
- ERROR: spaces required around that '=' (ctx:VxW)
- ERROR: space required before the open parenthesis '('
- ERROR: space required after that ',' (ctx:VxV)
- ERROR: need consistent spacing around '+' (ctx:WxV)
- WARNING: unnecessary whitespace before a quoted newline
- WARNING: please, no spaces at the start of a line
- WARNING: space prohibited between function name and open
parenthesis '('
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Wolfgang Denk <wd@denx.de> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org>
Luca Ceresoli [Wed, 11 May 2011 03:59:55 +0000 (03:59 +0000)]
net/net.c: cosmetic: variable initializations
This removes the following checkpatch errors:
- ERROR: do not initialise globals to 0 or NULL
- ERROR: spaces required around that '=' (ctx:VxV)
- ERROR: that open brace { should be on the previous line
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Wolfgang Denk <wd@denx.de> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org>
Luca Ceresoli [Wed, 11 May 2011 03:59:54 +0000 (03:59 +0000)]
net/net.c: cosmetic: fix lines over 80 characters
This removes the following checkpatch warning:
- WARNING: line over 80 characters
There are three such warnings left.
The first is hard to fix with cosmetic-only changes without compromising code
readability, so I'm leaving it as it is for now:
WARNING: line over 80 characters
#1537: FILE: net.c:1537:
+ [4 tabs] memcpy(((Ethernet_t *)NetArpWaitTxPacket)->et_dest, ...
The other two cannot be fixed without splitting string literals, so it is
preferred to keep them longer than 80 characters.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Wolfgang Denk <wd@denx.de> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Wed, 4 May 2011 10:32:28 +0000 (10:32 +0000)]
Fix incorrect use of getenv() before relocation
A large number of boards incorrectly used getenv() in their board init
code running before relocation. In some cases this caused U-Boot to
hang when certain environment variables grew too long.
Fix the code to use getenv_r().
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: The LEOX team <team@leox.org> Cc: Michael Schwingen <michael@schwingen.org> Cc: Georg Schardt <schardt@team-ctech.de> Cc: Werner Pfister <Pfister_Werner@intercontrol.de> Cc: Dirk Eibach <eibach@gdsys.de> Cc: Peter De Schrijver <p2@mind.be> Cc: John Zhan <zhanz@sinovee.com> Cc: Rishi Bhattacharya <rishi@ti.com> Cc: Peter Tyser <ptyser@xes-inc.com>
John Rigby [Tue, 19 Apr 2011 10:42:39 +0000 (10:42 +0000)]
Serial: p1011: new vendor init options
Two new options:
CONFIG_PL011_SERIAL_RLCR
Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
have separate receive and transmit line control registers. Set
this variable to initialize the extra register.
CONFIG_PL011_SERIAL_FLUSH_ON_INIT
On some platforms (e.g. U8500) U-Boot is loaded by a second stage
boot loader that has already initialized the UART. Define this
variable to flush the UART at init time.
empty fifo on init
Signed-off-by: John Rigby <john.rigby@linaro.org> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Steven A. Falco [Thu, 5 May 2011 14:08:35 +0000 (10:08 -0400)]
PPC405EX CHIP_21 erratum
APM errata CHIP_21 for the 405EX/EXr (from the rev 1.09 document dated
4/27/11) states that rev D processors may wake up with the wrong feature
set. This patch implements the APM-proposed workaround.
To enable this patch for your board, add the appropriate define for your
CPU to your board header file. See kilauea.h for more information. The
following variants are supported:
Simon Guinot [Tue, 3 May 2011 15:47:34 +0000 (21:17 +0530)]
Kirkwood: allow to override CONFIG_SYS_TCLK
This patch allow to override CONFIG_SYS_TCLK from board configuration
files. This is needed for the Network Space v2 which use a non standard
core clock frequency (166MHz instead of 200MHz for a 6281 SoC).
As a possible enhancement for 6281 and 6282 devices, TCLK could be
dynamically detected by checking the Sample at Reset register bit 21.
Additionally this patch fix a typo.
Signed-off-by: Simon Guinot <sguinot@lacie.com> Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Ben Gardiner [Wed, 20 Apr 2011 20:25:06 +0000 (16:25 -0400)]
da850evm: fix NAND WSTROBE and TA timings
The current NAND timings, introduced in commit a3f88293ddd13facd734769c1664d35ab4ed681f da850evm: setup the NAND flash
timings , incorrectly set WSTROBE and TA to 0. A more recent inspection of the
values set by the Linux kernel indicates that these should be set to 1.
Set the WSTROBE and TA field of the EMIFA cycle-count timings configuration to
1 to match the values set by linux.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> CC: Stefano Babic <sbabic@denx.de> CC: Sandeep Paulraj <s-paulraj@ti.com> CC: Scott Wood <scottwood@freescale.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Thomas Herzmann [Fri, 8 Apr 2011 02:47:41 +0000 (02:47 +0000)]
km/common: fix initial_boot_bank for bootpackages
The initial_boot_bank can be set when more than one application is
used in a bootpackage. But a value n <> 0 never led to booting from
bank n. Instead, bank 0 was booted. This patch fixes this.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Holger Brunck [Fri, 6 May 2011 00:41:55 +0000 (00:41 +0000)]
powerpc/km82xx: fix compile issue for mgcoge2ne
commit 91a3c14c (ppc, mgcoge: add DIP switch detection)
introduces an compile error due to an missing define in the
mgcoge2ne.h. DIP switch detection is valid for both boards.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Heiko Schocher <hs@denx.de>
poweprc/km82xx: add board specific environment variable
On mgcoge3ne a new environment variable bobcatreset is used.
So this patch adds a possibility to add board specific
environment variables in general and this specific variable
for mgcoge3ne.
Holger Brunck [Mon, 2 May 2011 22:56:55 +0000 (22:56 +0000)]
powerpc/km82xx: add mgcoge3ne and remove mgcoge2ne support
This patch adds support for the MPC8247 based board mgcoge3ne.
Additionaly mgcoge2ne board supprot was removed, because due
to the mgcoge3ne, this board is obsolete and not longer
maintained.
The board is similar to mgcoge. The difference is that
a NUMONYX flash is used and a different SDRAM (256MB).
Also introduce CONFIG_KM_82XX to collect ppc82xx common
settings and remove staticness from the common set_pin function.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
Huber, Andreas [Mon, 2 May 2011 22:56:54 +0000 (22:56 +0000)]
powerpc/km82xx: rework DIP switch detection
Introduce a struct for the BFTICU FPGA to increase the readability of
the code. And the define CONFIG_SYS_BFTICU_BASE was removed because
the CONFIG_SYS_FPGA_BASE is already the base value for BFTICU registers.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
The hdlc implementation for mgcoge was initially developed,
but later on not used. Remove the C files, the references
in mgcoge.c and the Makefile to decrease maintenance effort.
Current timer routines (arch/mips/lib/timer.c) are implemented assuming
that MIPS32 coprocessor (CP0) resources, Counter and Compare registers
in this case, are available. But this doesn't always work.
We need to make sure that all MIPS-based systems don't necessarily use
CP0 counter/compare registers as time keeping resources. And some MIPS
variant processors might come with different hardware specs with genuine
MIPS32 CP0 registers.
With this change, each $(CPU)/ directory can have its own timer code.
All architectures but MIPS are using --gc-sections on final linking.
This patch introduces that feature for MIPS to reduce the memory and
flash footprint.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Thomas Lange <thomas@corelatus.se> Cc: Vlad Lungu <vlad.lungu@windriver.com> Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
MIPS: Coding style cleanups on common assembly files
Fix style issues and alignments globally. No logical changes.
- Replace C comments with AS line comments where possible
- Use ifndef where possible, rather than if !defined for simplicity
- An instruction executed in a delay slot is now indicated by a leading
space, not by C comment
As requested in commit e1390801a3c1a2b6d12fa90be368efc19f5b9bfd ([MIPS]
Request for the 'mips_cache_lock()' removal), such feature is no longer
needed for current MIPS implementation of U-Boot, and no one in the tree
uses it for years.
Macpaul Lin [Mon, 11 Apr 2011 20:45:32 +0000 (20:45 +0000)]
cmd_ide: enhance new feature "CONFIG_IDE_AHB"
Although most IDE controller is designed to be connected to PCI bridge,
there are still some IDE controller support AHB interface for SoC design.
The driver implementation of these IDE-AHB controllers differ from other
IDE-PCI controller, some additional registers and commands access is required
during CMD/DATA I/O. Hence a configuration "CONFIG_IDE_AHB" in cmd_ide.c is
required to be defined to support these kinds of SoC controllers. Such as
Faraday's FTIDE020 series and Global Unichip's UINF-0301.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Mike Frysinger [Fri, 8 Apr 2011 12:23:30 +0000 (12:23 +0000)]
zlib: split up to match original source tree
While looking to upgrade to zlib-1.2.5, the current mondo merge of
multiple files into a single was making things way more difficult
than it should have been. Hard to pick out what has been changed
to port it to U-Boot, been removed as useless, and bug fixes added
after the fact.
So split the single file up into the original file names, and merge
non-essential changes back from the original tree (for some reason,
style in code in a bunch of places was changed to U-Boot style even
though this isn't "U-Boot" code).
The original build style is retained -- we have a single zlib.c that
includes all the other files, and that is the only file we compile.
Scott Wood [Wed, 6 Apr 2011 13:31:37 +0000 (13:31 +0000)]
Handle most LDSCRIPT setting centrally
Currently, some linker scripts are found by common code in config.mk.
Some are found using CONFIG_SYS_LDSCRIPT, but the code for that is
sometimes in arch config.mk and sometimes in board config.mk. Some
are found using an arch-specific rule for looking in CPUDIR, etc.
Further, the powerpc config.mk rule relied on CONFIG_NAND_SPL
when it really wanted CONFIG_NAND_U_BOOT -- which covered up the fact
that not all NAND_U_BOOT builds actually wanted CPUDIR/u-boot-nand.lds.
Replace all of this -- except for a handful of boards that are actually
selecting a linker script in a unique way -- with centralized ldscript
finding.
If board code specifies LDSCRIPT, that will be used.
Otherwise, if CONFIG_SYS_LDSCRIPT is specified, that will be used.
If neither of these are specified, then the central config.mk will
check for the existence of the following, in order:
$(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/$(CPUDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/board/$(BOARDDIR)/u-boot.lds
$(TOPDIR)/$(CPUDIR)/u-boot.lds
Some boards (sc3, cm5200, munices) provided their own u-boot.lds that
were dead code, because they were overridden by a CPUDIR u-boot.lds under
the old powerpc rules. These boards' own u-boot.lds have bitrotted and
no longer work -- these lds files have been removed.
Signed-off-by: Scott Wood <scottwood@freescale.com> Tested-by: Graeme Russ <graeme.russ@gmail.com>
Thomas Herzmann [Thu, 9 Dec 2010 10:02:09 +0000 (11:02 +0100)]
keymile boards: support of boardId / hwkey lists
In order to support boardId / hwkey lists, the u-boot default
environment has been updated: Added a script checkboardidlist
which checks the list of boardId / hwkey if the boadrId / hwkey
of the IVM is included in that list. This feature is used if you
got different HW variants but you only want to create one boot
package. E.g. supx5 board series.
Holger Brunck [Fri, 4 Mar 2011 13:56:27 +0000 (14:56 +0100)]
ppc, arm: rework and enhance keymile-common.h
Add:
- introduce "bootrunner" environment variable
This allows to execute consecutive different commands
specified in the list "subbootcmd". If one command fails
the command serie will stop.
- introduce environment variable "develop", "ramfs" and "release"
Each variable is one way to boot our linux. "develop" is for
development purpose and boots the SW via NFS. "release" is for
booting the linux image from flash, "ramfs" allows to load an SW
image via tftp into ram and executes from there
- introduce "addmem" variable, this command adds the used memory
for linux to the bootargs
- introduce "addvar" variable, this command adress for the /var
directory to the kernel command line
- introduce "setramfspram" and "setrootfsaddr" these calculation
were done if "ramfs" was used (only for debugging)
- introduce "tftpramfs" used for "ramfs" to load the image into
RAM (only for debugging)
Remove unneeded stuff:
- CONFIG_IO_MUXING is obsolete for keymile boards
- CONFIG_KM_DEF_ENV_PRIVATE is also obsolete
- define CONFIG_SYS_TEXT_BASE in board configs only
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
keymile, common: add setting of some environment variables
This patch adds last_stage_init to all keymile boards. And
in the last stage init some environment variables for u-boot
were set. Currently these are pnvramaddr, pram and var address.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
Normaly the PIGGY_MAC_ADRESS can be read directly from the
IVM on keymile boards. On mgcoge3 it differs. Because there
are two piggy boards deployed the second MAC adress must be
calculated with the IVM mac adress and an offset. This patch
allows to set such a offset in the board config.
Heiko Schocher [Tue, 8 Mar 2011 09:53:51 +0000 (10:53 +0100)]
arm, keymile: updates for the arm based boards from keymile
define KM_IVM_BUS and KM_ENV_BUS macros
KM_IVM_BUS is used to define the EEprom_ivm environment variable.
These macros allow the reuse of these I2C addresses in other code
locations.
remove unneeded code
On first HW versions the BOCO FPGA was behind a MUX device. These
HW versions are not supported anymore. And therefore this code can
be removed.
added LED initialization for SUEN3
The bootstat LED required to be initialized so to have a green
colour after start-up.
define CONFIG_SYS_TEXT_BASE
This is needed by the relocation code and is not the same for
our ARM BEC and thus needs to be defined.
remove memsize variable
An environment variable for memsize is not needed.
this can be get via the board info struct.
remove unneeded double access to bi_dram[i].size field
Heiko Schocher [Tue, 8 Mar 2011 09:51:15 +0000 (10:51 +0100)]
keymile, common; fix i2c deblocking support
This patch fix the i2c deblocking facility with the i2c HW-Controller.
The required delays for byte reading, the enhanced criteria for stop
the dummy read and required 5 start/stop sequences are added.
Add i2c deblocking before ivm eeprom read.
Improve i2c deblocking sequence by respecting stop hold time.
Cleaned function for deblocking. Have now one function i2c_make_abort()
available for bitbang, mpc82xx and mpc83xx harware controller.
Heiko Schocher [Tue, 8 Mar 2011 09:47:39 +0000 (10:47 +0100)]
ppc, 8321: cleanup tuxa1, tuda1 and suvd3 support
For the kmsupx5 a new header file was introduced km8321-common.h.
Now the common stuff from tuxa1, tuda1 and suvd3 was removed and
the new header file included.
The defines CONFIG_SYS_PIGGY_BASE and CONFIG_SYS_PIGGY_SIZE are
confusing. Because they actually describe the KMBEC FPGA values.
The KMBEC FPGA can be PRIO on kmeter1 or upio on mgcoge. Therefore
all the defines were renamed.
remove unneeded variable CONFIG_KM_DEF_NETDEV, as it is
already declared in keymile-common.h
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Heiko Schocher [Tue, 22 Feb 2011 08:34:33 +0000 (09:34 +0100)]
km_arm: change some register values for SDRAM initialization
These new values are:
- enables UART0 and UART1 pins in MPP
- define some L2 cache settings
- changes a SDRAM timing to better fit the hardware
- removed three writes that were the same as the reset values
Heiko Schocher [Tue, 22 Feb 2011 08:13:00 +0000 (09:13 +0100)]
km-arm: i2c support for suenx based boards
This patch renames the suen3 defines and functions to KM_KIRKWOOD
which is more generic and more precise, because these values
and functions where used by all suenX boards and not only suen3.
Heiko Schocher [Tue, 22 Feb 2011 07:58:19 +0000 (08:58 +0100)]
ppc: add support for ppc based board mgcoge2ne
The mgcoge2 board from keymile deploys two different processors.
An ARM based Kirkwood for the "unit" part of the SW and a PPC for
the "ne" part of the SW. Therefore in Linux and U-Boot the names
for the board are mgcoge2un and mgcoge2ne. This patch adds the
mgcoge2ne part of the board. The ppc part of mgboge2 is quite
similar to mgcoge, therefore a generic header km82xx-common.h
was introduced to collect all similiarities. Currently the only
difference is that mgcoge2ne has a 64 MB numonyx NOR flash with
a single die. The mgcoge has a dual die flash 2*32MB from spansion.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
mpc832x: add support for mpc8321 based tuda1 board
This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
mpc832x: add support for mpc8321 based tuxa1 board
This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Holger Brunck [Mon, 14 Mar 2011 15:01:04 +0000 (16:01 +0100)]
arm, ppc: rework environment variables for keymile boards
This patch reworks all headerfiles for keymile boards. Furthermore
the environment variables are refactored.
Changes:
- introduce km-powerpc.h file and extract ppc specific parts to it
- move ARM specific options and vaiables to km_arm.h
- sort the environment variables to logical groups
- enhance the description of the environment variables
- remove KM specific HW key and board id from kernel command line
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Heiko Schocher [Tue, 15 Mar 2011 15:52:29 +0000 (16:52 +0100)]
keymile: Fix Coding style issues for keymile boards.
- use I/O accessors
-> For accessing the FPGA therefore a struct km_bec_fpga
is introduced.
- no longer externs needed
- to defines, that only select functions, don;t assign a
numeric value
- Codingstyle changes to prevent checkpatch errors/warnings
Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Holger Brunck [Mon, 14 Mar 2011 14:31:19 +0000 (15:31 +0100)]
arm, keymile: rename MACH_SUEN3 to MACH_KM_KIRKWOOD
The MACH_TYPE SUEN3 is now to specific for keymile boards, because
other boards similar to suen3 will follow. So the MACH_SUEN3 was renamed
to MACH_KM_KIRKWOOD.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Kumar Gala [Thu, 28 Apr 2011 15:13:41 +0000 (10:13 -0500)]
powerpc/85xx: Bump up the CONFIG_SYS_BOOTM_LEN to 64M on FSL 85xx boards
CONFIG_SYS_BOOTMAPSZ has been 64M on these boards for some time so we
should also allow the kernel image to be up to 64M decompressed. This
also matches what we pass to the OS based on the ePAPR specification.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mingkai Hu [Tue, 26 Apr 2011 08:31:16 +0000 (16:31 +0800)]
powerpc: eSPI and eSPI controller support
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Singed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Shaohui Xie <b21989@freescale.com> Cc: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Andy Fleming [Fri, 29 Apr 2011 07:26:52 +0000 (02:26 -0500)]
tsec: Fix MDIO on devices with eTSEC2
The tsec driver was defining the default MDIO address as
the TSEC_BASE + 0x520, but on eTSEC2 controllers, the first
TSEC's registers are separated from the MDIO registers. Use
the existing MDIO_BASE_ADDR, instead.
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jason Liu [Tue, 22 Mar 2011 01:32:31 +0000 (01:32 +0000)]
fsl_esdhc: Fix multi-block read restriction on i.MX53 eSDHCv2
For freescale i.MX53 eSDHCv2, when using CMD12, cmdtype need
to be set to ABORT, otherwise, next read command will hang.
This is a software Software Restrictions in i.MX53 reference manual:
29.7.8 Multi-block Read
For pre-defined multi-block read operation, that is,the number of blocks
to read has been defined by previous CMD23 for MMC, or pre-defined number
of blocks in CMD53 for SDIO/SDCombo,or whatever multi-block read without
abort command at card side, an abort command, either automatic or manual
CMD12/CMD52, is still required by ESDHC after the pre-defined number of
blocks are done, to drive the internal state machine to idle mode. In this
case, the card may not respond to this extra abort command and ESDHC will
get Response Timeout. It is recommended to manually send an abort command
with RSPTYP[1:0] both bits cleared.
projects / u-boot.git / log