Becky Bruce [Thu, 6 Nov 2008 23:37:35 +0000 (17:37 -0600)]
mpc8641: Support 36-bit physical addressing
This patch creates a memory map with all the devices
in 36-bit physical space, in addition to the 32-bit map.
The CCSR relocation is moved (again, sorry) to
allow for the physical address to be 36 bits - this
requires translation to be enabled. With 36-bit physical
addressing enabled, we are no longer running with VA=PA
translations. This means we have to distinguish between
the two in the config file. The existing region name is
used to indicate the virtual address, and a _PHYS variety
is created to represent the physical address.
Large physical addressing is not enabled by default.
Set CONFIG_PHYS_64BIT in the config file to turn this on.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Becky Bruce [Thu, 6 Nov 2008 23:36:04 +0000 (17:36 -0600)]
mpc8641: Change 32-bit memory map
The memory map on the 8641hpcn is modified to look more like
the 85xx boards; this is a step towards a more standardized
layout going forward. As part of this change, we now relocate
the flash.
The regions for some of the mappings were far larger than they
needed to be. I have reduced the mappings to match the
actual sizes supported by the hardware.
In addition I have removed the comments at the head
of the BAT blocks in the config file, rather than updating
them. These get horribly out of date, and it's a simple
matter to look at the defines to see what they are set to
since everything is right here in the same file.
Documentation has been changed to reflect the new map, as this
change is user visible, and affects the OS which runs post-uboot.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Becky Bruce [Wed, 5 Nov 2008 20:55:35 +0000 (14:55 -0600)]
mpc86xx: Change early FLASH mapping to 1M at CONFIG_MONITOR_BASE_EARLY
We define CONFIG_MONITOR_BASE_EARLY to define the initial location
of the bootpage in flash. Use this to create an early mapping
definition for the FLASH, and change the early_bats code to use this.
This change facilitates the relocation of the flash since the early
mappings are no longer tied to the final location of the flash.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Becky Bruce [Wed, 5 Nov 2008 20:55:34 +0000 (14:55 -0600)]
mpc86xx: Use SRR0/1/rfi to enable address translation, not blr
Using a mtmsr/blr means that you have to be executing at the
same virtual address once you enable translation. This is
unnecessarily restrictive, and is not really how this is
usually done. Change it to use the more common mtspr SRR0/SRR1
and rfi method.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Becky Bruce [Wed, 5 Nov 2008 20:55:32 +0000 (14:55 -0600)]
mpc8641: Drop imaginary second flash bank, map 8MB
There's a lot of setup and foo for the second flash
bank. The problem is, this board doesn't actually have one.
Clean this up. Also, the flash is 8M in size. Get rid
of the confusing aliased overmapping, and just map 8M.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Becky Bruce [Wed, 5 Nov 2008 20:55:30 +0000 (14:55 -0600)]
mpc86xx: Move setup_bats into cpu_init_f
In order to later allow for a physical relocation of the
flash, setup_bats, which sets up the final BAT mapping
for the board, needs to happen *after* init_laws().
Otherwise, there will be no window programmed for the flash
at the new physical location at the point when we change
the mmu translation.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Stelian Pop [Fri, 7 Nov 2008 11:09:21 +0000 (12:09 +0100)]
AT91: Replace (undefined) AT91_ID_US* by the board specific values.
AT91_ID_US0 / AT91_ID_US1 / AT91_ID_US2 were used but never defined.
Since they are never used outside the board specific files, they can
be replaced by the board specific AT91xxx_ID_US0 / AT91xxx_ID_US1 /
AT91xxx_ID_US2.
Bug spotted by Jesus Alvarez <jalvarez@micromint.com>.
Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch provides support for AFEB9260 board, a product of
OpenSource hardware and software. Some commertial projects
are made with this design. A board is basically AT91SAM9260-EK
with some modifications and different peripherals and different
parts used. Main purpose of this project is to gain experience in
hardware design.
More info: http://groups.google.com/group/arm9fpga-evolution-board
(In Russian only, sorry).
Subversion repository: svn://194.85.238.22/home/users/george/svn/arm9eb
Roman Mashak [Wed, 22 Oct 2008 20:00:26 +0000 (16:00 -0400)]
ARM926EJ-S: relocate OMAP specific 'cpuinfo.c' into OMAP directory
OMAP identification is implemented in 'cpuinfo.c' and located in ARM926EJ-S directory.
It makes sense to place this file in OMAP specific subdirectory, i.e. cpu/arm926ejs/omap
Becky Bruce [Mon, 3 Nov 2008 21:44:01 +0000 (15:44 -0600)]
powerpc: change 86xx SMP boot method
We put the bootpg for the secondary cpus into memory and use
BPTR to get to it. This is a step towards converting to the
ePAPR boot methodology. Also, the code is written to
deal properly with more than 4GB of RAM.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Becky Bruce [Fri, 31 Oct 2008 22:13:49 +0000 (17:13 -0500)]
8641HPCN: Config file cleanup
There are several items in the config file that were hardcoded
but that should really be based on other config options, since
the regions are contiguous and depend on being so. This cleans
that up a bit. Also, add BR_PHYS_ADDR() macro to convert
addresses into the proper format for BR registers.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Becky Bruce [Mon, 3 Nov 2008 00:19:32 +0000 (18:19 -0600)]
powerpc 86xx: Handle CCSR relocation earlier
Currently, the CCSR gets relocated while translation is
enabled, meaning we need 2 BAT translations to get to both the
old location and the new location. Also, the DEFAULT
CCSR location has a dependency on the BAT that maps the
FLASH region. Moving the relocation removes this unnecessary
dependency. This makes it easier and more intutive to
modify the board's memory map.
Swap BATs 3 and 4 on 8610 so that all 86xx boards use the same
BAT for CCSR space.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Becky Bruce [Fri, 31 Oct 2008 22:14:14 +0000 (17:14 -0500)]
mpc8641: Make PCI and RIO mutually exclusive, fix non-PCI build
You can't actually have both, and with some coming changes to
change the memory map for the board and support 36-bit physical,
we need the extra BAT that is being consumed by having both.
I also make non-PCI configs build cleanly, for the sake of sanity.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
TsiChung Liew [Fri, 24 Oct 2008 12:59:12 +0000 (12:59 +0000)]
ColdFire: Fix M5329EVB and M5373EVB nand issue
Fix compilation issue caused by a few mismatches.
Provide proper nand chip select enable/disable in
nand_hwcontrol() rather than in board_nand_init()
just enable once. Remove redundant local nand driver
functions - nand_read_byte(), nand_write_byte() and
nand_dev_ready() to use common nand driver.
TsiChung Liew [Tue, 21 Oct 2008 12:15:44 +0000 (12:15 +0000)]
ColdFire: Remove platforms mii.c file
Will use mcfmii.c driver in drivers/net rather than
keep creating new mii.c for each future platform.
Remove EB+MCF-EV123, cobra5272, idmr, M5235EVB,
M5271EVB, M5272C3, M5275EVB, M5282EVB, M5329EVB,
M5373EVB, M54451EVB, M54455EVB, M547xEVB, and M548xEVB's
mii.c
TsiChung Liew [Tue, 21 Oct 2008 10:03:07 +0000 (10:03 +0000)]
ColdFire: Modules header files cleanup
Consolidate ATA, ePORT, QSPI, FlexCan, PWM, RNG,
MDHA, SKHA, INTC, and FlexBus structures and
definitions in immap_5xxx.h to more unify modules
header files. Append DSPI support for m547x_8x.
SSI cleanup. Remove USB Host structure from immap_539.h.
Apply changes to use FlexBus structures in mcf52x2's
cpu_init.c and platform configuration files.
This removes in nand.h code that is verbatim duplicated from bbm.h,
including directly bbm.h in nand.h. The previous state of affairs
prevented compiling code for a board hosting both NAND and OneNAND chips.
Reported-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Alessandro Rubini <rubini@unipv.it> Signed-off-by: Scott Wood <scottwood@freescale.com>
Jason Jin [Fri, 31 Oct 2008 10:07:04 +0000 (05:07 -0500)]
NAND: Add NAND support for MPC8536DS board
This patch defines 1M TLB&LAW size for NAND on MPC8536DS, assigns 0xffa00000
for CONFIG_SYS_NAND_BASE and adds other NAND supports in config file.
It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image.
Singed-off-by: Jason Jin <Jason.Jin@freescale.com> Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Wolfgang Denk [Fri, 31 Oct 2008 00:12:28 +0000 (01:12 +0100)]
CFI Driver: Fix "flash not ready" problem
This patch fixes a problem on systems where the NOR flash is attached
to a 64 bit bus. The toggle bit detection in flash_toggle() is based
on the assumption that the same flash address is read twice without
any other interjacent flash accesses. However, on 32 bit systems the
function flash_read64() [as currently implemented] does not perform
an atomic 64 bit read - instead, this is broken down into two 32 bit
read accesses on addresses "addr" and "addr + 4". So instead of
reading a 64 bit value twice from "addr", we see a sequence of 4 32
bit reads from "addr", "addr + 4", "addr", and "addr + 4". The
consequence is that flash_toggle() fails to work.
This patch implements a simple, but somewhat ugly solution, as it
avoids the use of flash_read64() in this critical place (by breaking
it down manually into 32 bit read operations) instead of rewriting
flash_read64() such to perform atomic 64 bit reads as one could
expect. However, such a rewrite would require the use of floating
point load operations, which becomes pretty complex:
save MSR;
set Floating Point Enable bit in MSR;
use "lfd" instruction to perform atomic 64 bit read;
use "stfd" to store value to temporary variable on stack;
load u64 value from temporary variable;
restore saved MSR;
return u64 value;
The benefit-cost ratio of such an implementation was considered too
bad to actually attempt this, especially as we can expect that such
an implementation would not only have a bigger memory footprint but
also cause a performance degradation.
Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Tue, 28 Oct 2008 12:37:00 +0000 (13:37 +0100)]
ppc4xx: Update PMC440 board support
This patch brings PMC440 board support up to date:
- fix GPIO configuration
- add misc_init_f()
- use better values for usbact variable
- fix USB 2.0 phy reset sequence
- shrink BAR2 to save PCI address space
- add FDT support
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
David Gibson [Thu, 30 Oct 2008 04:27:45 +0000 (23:27 -0500)]
libfdt: Fix bug in fdt_subnode_offset_namelen()
There's currently an off-by-one bug in fdt_subnode_offset_namelen()
which causes it to keep searching after it's finished the subnodes of
the given parent, and into the subnodes of siblings of the original
node which come after it in the tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Korsgaard [Tue, 28 Oct 2008 07:26:52 +0000 (08:26 +0100)]
fdt_resize(): ensure minimum padding
fdt_add_mem_rsv() requires space for a struct fdt_reserve_entry
(16 bytes), so make sure that fdt_resize at least adds that much
padding, no matter what the location or size of the fdt is.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Andy Fleming <afleming@freescale.com>
Dave Liu [Tue, 28 Oct 2008 09:47:49 +0000 (17:47 +0800)]
86xx: remove the redundant r2 global data pointer save
The commit 67256678f00c09b0a7f19e862e5c1847553d31bc add
the another global data pointer save, but in fact the
global data pointer will be initialized in the board_init_r,
so remove it such as the 85xx/83xx family.
Signed-off-by: Dave Liu <daveliu@freescale.com> Acked-by: Kumar Gala <kumar.gala@freescale.com>
Dave Liu [Tue, 28 Oct 2008 09:46:23 +0000 (17:46 +0800)]
86xx: remove the unused ddr_enable_ecc in the board file
The DDR controller of 86xx processors have the ECC data init
feature, and the new DDR code is using the feature, we don't
need the way with DMA to init memory again.
Signed-off-by: Dave Liu <daveliu@freescale.com> Acked-by: Kumar Gala <kumar.gala@freescale.com>
Dave Liu [Tue, 28 Oct 2008 09:46:12 +0000 (17:46 +0800)]
86xx: Move the clear_tlbs before MMU turn on
We must invalidate TLBs before MMU turn on, but
currently the code is not, if there are some stale
TLB entry valid in the TLBs, it will cause strange
issue.
Signed-off-by: Dave Liu <daveliu@freescale.com> Acked-by: Becky Bruce <becky.bruce@freescale.com>
Scott Wood [Wed, 29 Oct 2008 19:20:26 +0000 (14:20 -0500)]
NAND: Properly create JFFS2 cleanmarkers.
As reported by Ilko Iliev <iliev@ronetix.at>, the "nand erase clean"
command is currently broken, and among other things causes all blocks
to be marked bad.
This implements it properly using MTD_OOB_AUTO, along with some
indentation fixes.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Haiying Wang [Wed, 29 Oct 2008 17:32:59 +0000 (13:32 -0400)]
NAND: Add support for MPC8572DS board
This patch defines 1M TLB&LAW size for NAND on MPC8572DS, assigns
0xffa00000 for CONFIG_SYS_NAND_BASE and adds other NAND supports in
config file.
It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image, to
make room for the increased code size with NAND enabled.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com> Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Haiying Wang [Wed, 29 Oct 2008 15:05:55 +0000 (11:05 -0400)]
Make Freescale local bus registers available for both 83xx and 85xx.
- Rename lbus83xx_t to fsl_lbus_t and move it to asm/fsl_lbc.h so that it
can be shared by both 83xx and 85xx
- Remove lbus83xx_t and replace it with fsl_lbus_t in all 83xx boards
files which use lbus83xx_t.
- Move FMR, FIR, FCR, FPAR, LTESR from mpc83xx.h to asm/fsl_lbc.h so that
85xx can share them.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com> Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Karl Beldan [Mon, 15 Sep 2008 14:08:03 +0000 (16:08 +0200)]
NAND: Reset chip on power-up
Some chips require a RESET after power-up (e.g. Micron MT29FxGxxxxx).
The first command sent is NAND_CMD_READID.
Issue a NAND_CMD_RESET in nand_scan_ident before reading the device id.
Tested with an MT29F4G08AAC.
Signed-off-by: Karl Beldan <karl.beldan@gmail.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Fri, 24 Oct 2008 21:20:43 +0000 (16:20 -0500)]
NAND: sync with 2.6.27
This brings the core NAND code up to date with the Linux kernel.
Since there were several drivers in Linux as of the last update that are
not in u-boot, I'm not bringing over new drivers that have been added
since in the absence of an interested party.
I did not update OneNAND since it was recently synced by Kyungmin Park,
and I'm not sure exactly what the common ancestor is.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Kumar Gala [Tue, 21 Oct 2008 22:25:45 +0000 (17:25 -0500)]
bootm: Add subcommands
Add the ability to break the steps of the bootm command into several
subcommands: start, loados, ramdisk, fdt, bdt, cmdline, prep, go.
This allows us to do things like manipulate device trees before
they are passed to a booting kernel or setup memory for a secondary
core in multicore situations.
Not all OS types support all subcommands (currently only start, loados,
ramdisk, fdt, and go are supported).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Mon, 27 Oct 2008 21:42:00 +0000 (16:42 -0500)]
85xx: Update MPC85xx_PORDEVSR_IO_SEL mask
The MPC8572 has a 4-bit wide PORDEVSR IO_SEL field. Other MPC85xx
processors have a 3-bit wide IO_SEL field but have the most
significant bit is wired to 0 so this change should not affect
them.
projects / u-boot.git / log