Simon Glass [Tue, 23 Jun 2015 21:39:13 +0000 (15:39 -0600)]
dm: Add a system reset uclass
It is common for system reset to be available at multiple levels in modern
hardware. For example, an SoC may provide a reset option, and a board may
provide its own reset for reasons of security or thoroughness. It is useful
to be able to model this hardware without hard-coding the behaviour in the
SoC or board. Also there is a distinction sometimes between resetting just
the CPU (leaving GPIO state alone) and resetting all the PMICs, just cutting
power.
To achieve this, add a simple system reset uclass. It allows multiple devices
to provide reset functionality and provides a way to walk through them,
requesting a particular reset type until is it provided.
Simon Glass [Tue, 23 Jun 2015 21:39:12 +0000 (15:39 -0600)]
mkimage: Set up a file size parameter and keep it updated
Some functions called by mkimage would like to know the output file size.
Initially this is the same as the input file size, but it may be affected by
adding headers, etc.
Add this information to the image parameters.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Tue, 23 Jun 2015 21:39:10 +0000 (15:39 -0600)]
dm: spl: Allow device tree/driver model in board_init_f()
Add an spl_init() function that does basic init such that board_init_f() can
use simple malloc(), device tree and driver model. Each one is set up only
if enabled for SPL.
Note: We really should refactor SPL such that there is a single
board_init_f() and rename the existing weak board_init_f() functions
provided by boards, calling them from the single board_init_f().
Simon Glass [Tue, 23 Jun 2015 21:39:04 +0000 (15:39 -0600)]
dm: Add support for RAM drivers
Add support for a driver which sets up DRAM and can return information about
the amount of RAM available. This is a first step towards moving RAM init
to driver model.
Simon Glass [Tue, 23 Jun 2015 21:38:58 +0000 (15:38 -0600)]
dm: pmic: Split output from function
The regulator_autoset() function mixes printf() output and PMIC adjustment
code. It provides a boolean to control the output. It is better to avoid
missing logic and output, and this permits a smaller SPL code size. So
split the output into a separate function.
Also rename the function to have a by_name() suffix, since we would like
to be able to pass a device when we know it, and thus avoid the name
search.
Simon Glass [Tue, 23 Jun 2015 21:38:57 +0000 (15:38 -0600)]
dm: power: Add regulator flags to centralise auto-set logic
Decide when the regulator is set up whether we want to auto-set the voltage
or current. This avoids the complex logic spilling into the processing code.
Simon Glass [Tue, 23 Jun 2015 21:38:56 +0000 (15:38 -0600)]
dm: power: Avoid case-insensitve match for child names
This is not user input (i.e. from the command line). It should be possible
to get the case correct and avoid the case-insensitive match. This will
help avoid sloppy device tree setups.
Simon Glass [Tue, 23 Jun 2015 21:38:43 +0000 (15:38 -0600)]
dm: Add support for generic system controllers (syscon)
Many SoCs have a number of system controllers which are dealt with as a
group by a single driver. It is a pain to have to add lots of compatible
strings and/or separate drivers for each. Instead we can identify the
controllers by a number and request the address of the one we want.
Add a simple implementation of this which can be used by SoC driver code.
Simon Glass [Tue, 23 Jun 2015 21:38:42 +0000 (15:38 -0600)]
dm: Add support for register maps (regmap)
Add a simple implementaton of register maps, supporting only direct I/O
for now. This can be enhanced later to support buses which have registers,
such as I2C, SPI and PCI.
It allows drivers which can operate with multiple buses to avoid dealing
with the particulars of register access on that bus.
Simon Glass [Tue, 23 Jun 2015 21:38:37 +0000 (15:38 -0600)]
dm: core: Add a function to find any device from device tree
In some rare cases it is useful to be able to locate a device given a device
tree node offset. An example is when you have an alias that points to a node
and you want to find the associated device. The device may be SPI, MMC or
something else, but you don't need to know the uclass to find it.
Add a function to do a global search for a device, given its device tree
offset.
Simon Glass [Tue, 23 Jun 2015 21:38:36 +0000 (15:38 -0600)]
dm: core: Use debug() instead of printf() for failures
To avoid bloating SPL code, use debug() where possible in the driver model
core code. The error code is already returned, and can be investigated as
needed.
Simon Glass [Tue, 23 Jun 2015 21:38:35 +0000 (15:38 -0600)]
dm: Move the tree/uclass dump code into its own file
In SPL it is sometimes useful to be able to obtain a dump of the current
driver model state. Since commands are not available, provide a way to
directly call the functions to output this information.
Adjust the existing commands to use these functions.
Simon Glass [Tue, 23 Jun 2015 21:38:34 +0000 (15:38 -0600)]
sandbox: Drop special-case sandbox console code
At present printf() skips output if it can see there is no console. This
is really just an optimisation, and is not necessary. Also it is currently
incorrect in some cases. Rather than update the logic, just remove it so
that we don't need to keep it in sync.
Simon Glass [Tue, 23 Jun 2015 21:38:31 +0000 (15:38 -0600)]
Add a way of checking the position of a structure member
U-Boot uses structures for hardware access so it is important that these
structures are correct. Add a way of asserting that a structure member is
at a particular offset. This can be created using the datasheet for the
hardware.
This implementation uses Static_assert() since BUILD_BUG_ON() only works
within functions.
Simon Glass [Tue, 23 Jun 2015 21:38:29 +0000 (15:38 -0600)]
dm: Reduce SPL device tree size
The SPL device tree size must be minimised to save memory. Only include
properties that are needed by SPL - this is determined by the presence
of the "u-boot,dm-pre-reloc" property. Also remove a predefined list of
unused properties from the nodes that remain.
Simon Glass [Tue, 23 Jun 2015 21:38:28 +0000 (15:38 -0600)]
fdt: Add fdtgrep tool
This tool allows us to extract subsets of a device tree file. It is used by
the SPL vuild, which needs to cut down the device tree size for use in
limited memory.
This tool was originally written for libfdt but it has not been accepted
upstream, so for now, include it in U-Boot. Several utilfdt library
functions been included inline here.
If fdtgrep is eventually accepted in libfdt then we can bring that version
of libfdt in here, and drop fdtgrep (requiring that fdtgrep is provided by
the user).
If it is not accepted then another approach would be to write a special
tool for chopping down device tree files for SPL. While it would use the
same libfdt support, it would be less code than fdtgrep.c because it would
not have general-purpose functions.
Another approach (which was used with v1 of this series) is to sprinkler all
the device tree files with #ifdef. I don't like that idea.
Simon Glass [Tue, 23 Jun 2015 21:38:27 +0000 (15:38 -0600)]
fdt: Add fdt_first/next_region() functions
These have been sent upstream but not accepted to libfdt. For now, bring
these into U-Boot to enable fdtgrep to operate. We will use fdtgrep to
cut device tree files down for SPL.
Simon Glass [Tue, 23 Jun 2015 21:38:26 +0000 (15:38 -0600)]
fdt: Add a function to remove unused strings from a device tree
Property names are stored in a string table. When a node property is
removed, the string table is not updated since other nodes may have a
property with the same name.
Thus it is possible for the string table to build up a number of unused
strings. Add a function to remove these. This works by building a new device
tree from the old one, adding strings one by one as needed.
Simon Glass [Tue, 23 Jun 2015 21:38:25 +0000 (15:38 -0600)]
mkimage: Display a better list of available image types
Offer to display the available image types in help. Also, rather than
hacking the genimg_get_type_id() function to display a list of types,
do this in the tool. Also, sort the list.
The list of image types is quite long, and hard to discover. Print it out
when we show help information.
armv8/ls2085a/defconfig: Enable FSL_DSPI, OF_CONTROL and DM support
Freescale DSPI driver has been converted to Driver Model.
The new driver depends on OF_CONTROL, DM, DM_SPI.
This patch enable FSL_DSPI and its dependence configure options.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
armv8/ls2085ardb: DSPI pin muxing configure through QIXIS CPLD
DSPI has pin muxing with SDHC and other IPs, this patch check the
value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check
the "hwconfig" variable. If those pins are configured to DSPI and
"hwconfig" enable DSPI, set the BRDCFG5 of QIXIS CPLD to configure
the routing to on-board SPI memory. Otherwise will configure to SDHC.
DSPI is enabled in "hwconfig" by appending "dspi", eg.
setenv hwconfig "$hwconfig;dspi"
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Haikun Wang [Fri, 26 Jun 2015 11:58:12 +0000 (19:58 +0800)]
armv8/ls2085aqds: DSPI pin muxing configure through QIXIS
DSPI has pin muxing with SDHC and other IPs, this patch check the
value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check
the "hwconfig" variable. If those pins are configured to DSPI and
"hwconfig" enable DSPI, set the BRDCFG5 of QIXIS FPGA to configure
the routing to on-board SPI memory. Otherwise will configure to SDHC.
DSPI is enabled in "hwconfig" by appending "dspi", eg.
setenv hwconfig "$hwconfig;dspi"
Signed-off-by: Haikun Wang <haikun.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Wang Dongsheng [Thu, 4 Jun 2015 04:01:09 +0000 (12:01 +0800)]
arm/ls102xa: Add PSCI support for ls102xa
Base on PSCI services, implement CPU_ON/CPU_OFF for ls102xa platform.
Tested on LS1021AQDS, LS1021ATWR.
Test CPU hotplug times: 60K
Test kernel boot times: 1.2K
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com> Acked-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Wang Dongsheng [Thu, 4 Jun 2015 04:01:08 +0000 (12:01 +0800)]
ARMv7: Factor out reusable timer_wait from sunxi/psci_sun7i.S
timer_wait is moved from sunxi/psci_sun7i.S, and it can be converted
completely into a reusable armv7 generic timer. LS1021A will use it
as well.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Mon, 11 May 2015 07:39:47 +0000 (15:39 +0800)]
arm: ls1021a: Remove the inappropriate use of the function 'sprintf'
As the function 'sprintf' does not check buffer boundaries but outputs
to the buffer 'enet' of fixed size (16), this patch removes the function
'sprintf', and uses 'strcpy' instead. It will assign the character
arrays 'enet' and 'phy' the corresponding character strings.
Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
Polling of TX conf frames is not a mandatory option.
Packets can be transferred via WRIOP without TX conf frame.
Configure ldpaa_eth driver to use TX path without confirmation frame
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
Volatile command does not return frame immidiately, need to wait till a frame
is available in DQRR. Ideally it should be a blocking call.
Add timeout handling for DQRR frame instead of retry counter.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
driver/ldpaa_eth: Retry enqueue if portal was busy
Do not immediately return if the enqueue function returns -EBUSY; re-try
mulitple times.
if timeout occures, release the buffer.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
Stuart Yoder [Thu, 2 Jul 2015 05:59:04 +0000 (11:29 +0530)]
armv8/fsl-lsch3: device tree fixups for PCI stream IDs
This patch adds the infrastructure to update device
tree nodes to convey SMMU stream IDs in the device
tree. Fixups are implemented for PCI controllers
initially.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Stuart Yoder [Thu, 2 Jul 2015 05:59:03 +0000 (11:29 +0530)]
drivers/fsl-mc: dynamically create ICID pool in DPC
delete any existing ICID pools in the DPC and create
a new one based on the stream ID partitioning for
the SoC
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Stuart Yoder [Thu, 2 Jul 2015 05:59:02 +0000 (11:29 +0530)]
armv8/fsl-lsch3: partition stream IDs
Stream IDs on ls2085a devices are not hardwired and are
programmed by sw. There are a limited number of stream IDs
available, and the partitioning of them is scenario dependent.
This header defines the partitioning between legacy, PCI,
and DPAA2 devices.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
drivers: fsl-mc: Return error for major version mismatch
Management complex major version should match to the firmware present in flash.
Return error during mismatch of major version.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
Update qbman driver
- As per latest available qbman driver
- Use of atomic APIs
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> CC: Geoff Thorpe <Geoff.Thorpe@freescale.com> CC: Haiying Wang <Haiying.Wang@freescale.com> CC: Roy Pledge <Roy.Pledge@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Update flibs changes to mc-0.6.0.1 for dpmang, dprc, dpni and dpio objects
Also rename qbman_portal_ce/ci_paddr to qbman_portal_ce/ci_offset in
dpio_attr. These are now offsets from the SoC QBMan portals base.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
drivers/fsl-mc: Autoload AOIP image from NOR flash
Load AIOP image from NOR flash into DDR so that the MC firmware
the MC fw can start it at boot time
Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
drivers/fsl-mc: Make MC boot error messages more readable
Make it easier for the user to notice when the MC firmware
had problems booting.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Stuart Yoder [Thu, 28 May 2015 09:24:15 +0000 (14:54 +0530)]
armv8/ls2085a: enable debug server
Signed-off-by: Stuart Yoder <stuart.yoder at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
armv8/fsl-lsch3: Support 256M mem split for MC & dbg-srvr
The agreed split of the top of memory is 256M for debug server and 256M
for MC. This patch implements the split.
In addition, the MC mem must be 512MB aligned, so the amount of memory
to hide must be 512MB to achieve that alignment.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Bhupesh Sharma [Thu, 28 May 2015 09:24:13 +0000 (14:54 +0530)]
arm/errata: Update required bits for A57 cores erratas
This patch updates the setting of required bits for A57 cores erratas
- 828024 and 826974
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com> Signed-off-by: Dai Haruki <dai.haruki at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Bhupesh Sharma [Thu, 28 May 2015 09:24:12 +0000 (14:54 +0530)]
driver/fsl_debug_server: Fix the DDR hide logic for LS2085a
This patch fixes the DDR hide logic for LS2085a, correcting the way
the Debug Server FW and MC FW images are placed on the top of system
DDR and how the rest of the system DDR space is made visibile to Linux.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Update SoC README to provide details of
- Memory regions
- Memory used by MC and Debug server
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Bhupesh Sharma [Thu, 28 May 2015 09:24:10 +0000 (14:54 +0530)]
armv8/ls2085a: Expose all DDR region(s) to Linux
This patch allows u-boot to expose the complete DDR region(s) to Linux
(after subtracting the memory hidden via MEM_TOP_HIDE mechanism).
This allows the u-boot to support the 48-bit VA support provided by
ARM64 Linux in flavors 3.18 and above, by passing the appropriate
'memory' DTS nodes.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
York Sun [Thu, 28 May 2015 09:24:09 +0000 (14:54 +0530)]
armv8/ls2085ardb: Fix SPD address error on early boards
Board rev C and earlier has duplicated SPD address on 2nd DDR
controller slots. It is fixed on rev D and later. SPD addresses
need to be updated accordingly.
Signed-off-by: York Sun <yorksun at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
armv8/fsl-ch3: Add support to print SoC personality
This patch adds support to print out the SoC personality.
Freescale LS20xx SoCs (compliant to Chassis-3 specifications) can
have 6 personalities: LS2045AE, LS2045A, LS2080AE, LS2080A,
LS2085AE and LS2085A
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Jaiprakash Singh [Thu, 28 May 2015 09:24:03 +0000 (14:54 +0530)]
board/fsl/common: Fix eeprom system version endianness
SYSTEM ID EPPROM always store SYSTEM version info in big endian format.
SoC with ARM or PowerPC core should read/write version info from eeprom
in BIG endian format.
So use cpu-specific APIs to read SYSTEM version.
Signed-off-by: Jaiprakash Singh <b44839 at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Bhupesh Sharma [Thu, 28 May 2015 09:24:02 +0000 (14:54 +0530)]
armv8/ls2085a: Increase the supported kernel size
Increases the kernel size supported for LS2085A platforms:-
- Update environment variables
- Add ramdisk_size in bootargs env variable
- Define CONFIG_SYS_BOOTM_LEN to 64MB
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
armv8/ls2085qds: Update SFP TX bit as "0" to enable XFI
FPGA BRDCFG9[SFP_TX] should be clear in order to enable XFI ports.
Signed-off-by: Dai Haruki <Dai.Haruki at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
armv8/ls2085a: call ft_pcie_setup() to change dts status
call ft_pci_setup() to disable PCIe dts node if corresponding
PCIe controller is disabled according to RCW
Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Compatible field "fsl,20851a-pcie" is not correct.
So update it to "fsl,ls2085a-pcie"
Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Priyanka Jain [Thu, 28 May 2015 09:23:56 +0000 (14:53 +0530)]
armv8/ls2085a: Enable "date" command for QDS and RDB
Enable "date" command for QDS and RDB boards
Signed-off-by: Priyanka Jain <Priyanka.Jain at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Yangbo Lu [Thu, 28 May 2015 09:23:55 +0000 (14:53 +0530)]
armv8/ls2085ardb: add hwconfig setting for eSDHC
Add hwconfig setting for eSDHC since it shares some pins with other
IP block.
Signed-off-by: Yangbo Lu <yangbo.lu at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
armv8/ls2085ardb: Add eth & phy firmware loading support
Add support for board eth initialization and support for loading phy
firmware. PHY firmware needs to be loaded from board_eth_init() because
all the MACs are not initialized by ldpaa_eth driver.
Signed-off-by: pankaj chauhan <pankaj.chauhan at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
projects / u-boot.git / log