Sam Protsenko [Wed, 14 Aug 2019 19:52:51 +0000 (22:52 +0300)]
mmc: Rename timeout parameters for clarification
It's quite hard to figure out time units for various function that have
timeout parameters. This leads to possible errors when one forgets to
convert ms to us, for example. Let's rename those parameters
correspondingly to 'timeout_us' and 'timeout_ms' to prevent such issues
further.
While at it, add time units info as comments to struct mmc fields.
This commit doesn't change the behavior, only renames parameters names.
Buildman should report no changes at all.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Sam Protsenko [Wed, 14 Aug 2019 19:52:50 +0000 (22:52 +0300)]
mmc: Fix timeout values passed to mmc_wait_dat0()
mmc_wait_dat0() expects timeout argument to be in usec units. But some
overlying functions operate on timeout in msec units. Convert timeout
from msec to usec when passing it to mmc_wait_dat0().
This fixes 'avb' commands on BeagleBoard X15, because next chain was
failing:
when passing incorrect timeout from __mmc_switch() to mmc_wait_dat0().
Fixes: bb98b8c5c06a ("mmc: During a switch, poll on dat0 if available and check the final status") Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com> Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Tested-by: Igor Opaniuk <igor.opaniuk@gmail.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
arc: emsdp: Add more platform-specific compiler options
Even though EM SDP is FPGA-based board and different FPGA
images (known as .bit-files) are awailable for the board still
there's a common subset of options we may rely on for all configs.
These are:
* Normalizer
* Swap instructions
* Simple multiplier
* Barrel-shifter
* Floating-point unit
* Shorter instructions (code density)
This among other improvements allows to compile code with
64-bit divisions, see [1].
- Skip unavailable hart in the get_count().
- fu540 set serial env from otp.
- fu540 add mmc0 as a boot target device.
- Update fix_rela_dyn and add absolute reloc addend.
- Andestech PLIC driver will skip unavailable hart.
- Support Andestech V5L2 cache driver.
Rick Chen [Wed, 28 Aug 2019 10:46:10 +0000 (18:46 +0800)]
riscv: dts: move out AE350 L2 node from cpus node
When L2 node exists inside cpus node, uclass_get_device
can not parse L2 node successfully. So move it outside
from cpus node.
Also add tag-ram-ctl and data-ram-ctl attributes for
v5l2 cache controller driver. This can adjust timing
by requirement from dtb to improve performance.
Signed-off-by: Rick Chen <rick@andestech.com> Cc: KC Lin <kclin@andestech.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Marcus Comstedt [Sun, 11 Aug 2019 12:45:29 +0000 (14:45 +0200)]
riscv: update fix_rela_dyn
The addend is now added for RELOC_TYPE relocs. Also, changed the loop
structure so that all the R_RISCV_RELATIVE relocs are not required to
be at the beginning of the list.
Signed-off-by: Marcus Comstedt <marcus@mc.pp.se> Cc: Rick Chen <rick@andestech.com>
Marcus Comstedt [Sun, 11 Aug 2019 09:29:57 +0000 (11:29 +0200)]
riscv: tools: Handle addend to absolute reloc in prelink-riscv
Previously the handling of R_RISCV_32 and R_RISCV_64 would simply
insert the value of the symbol and ignore any addend. However, there
exist relocs where the addend is non-zero:
Peng Fan [Thu, 8 Aug 2019 01:43:30 +0000 (01:43 +0000)]
i2c: mxc: add CONFIG_CLK support
When CONFIG_CLK enabled, use CLK UCLASS for clk related settings.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
hs: removed hunk in mxc_i2c_probe() as not longer in code
Rasmus Villemoes [Wed, 28 Aug 2019 11:00:46 +0000 (11:00 +0000)]
Makefile: fix newline escaping for CONFIG_DEFAULT_ENV_FILE
I wanted this to be compatible with mkenvimage, including the ability
to embed newlines in variables by escaping them. But I failed to check
that it works more than once.
Suniel Mahesh [Thu, 29 Aug 2019 13:38:59 +0000 (19:08 +0530)]
arm: omap2: am43xx: Enable CONFIG_DM_USB
Enable CONFIG_DM_USB to remove compile warning for
am43xx based targets:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Weijie Gao [Tue, 27 Aug 2019 07:32:19 +0000 (15:32 +0800)]
mmc: invalidate block cache after hwpart switched successfully
eMMC device has multiple hw partitions both address from zero. However the
mmc driver lacks block cache invalidation for switch hwpart. This causes a
problem that data of current hw partition is cached before switching to
another hw partition. And the following read operation of the latter hw
partition will get wrong data when reading from the addresses that have
been cached previously.
To solve this problem, invalidate block cache after a successful
mmc_switch_part() operation.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> Tested-by: Felix Brack <fb@ltec.ch>
Most block devices have only one hwpart. Multiple hwparts only found used
by eMMC devices in u-boot. The mmc driver do blk_dselect_hwpart() at the
beginning of mmc_bread() which causes block cache being invalidated too
frequently and makes block cache useless.
So it's not a good idea to put blkcache_invalidate() in the common
functions. It should be called inside mmc_select_hwpart().
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> Tested-by: Felix Brack <fb@ltec.ch>
Stephen Warren [Tue, 27 Aug 2019 17:54:31 +0000 (11:54 -0600)]
board_f: fix noncached reservation calculation
The current code in reserve_noncached() has two issues:
1) The first update of gd->start_addr_sp always rounds down to a section
start. However, the equivalent calculation in cache.c:noncached_init()
always first rounds up to a section start, then subtracts a section size.
These two calculations differ if the initial value is already rounded to
section alignment.
2) The second update of gd->start_addr_sp subtracts exactly
CONFIG_SYS_NONCACHED_MEMORY, whereas the equivalent calculation in
cache.c:noncached_init() rounds the noncached size up to section
alignment before subtracting it. The two calculations differ if the
noncached region size is not a multiple of the MMU section size.
In practice, one/both of those issues causes a practical problem on
Jetson TX1; U-Boot triggers a synchronous abort during initialization,
likely due to overlapping use of some memory region.
This change fixes both these issues by duplicating the exact calculations
from noncached_init() into reserve_noncached().
However, this fix assumes that gd->start_addr_sp on entry to
reserve_noncached() exactly matches mem_malloc_start on entry to
noncached_init(). I haven't traced the code to see whether it absolutely
guarantees this in all (or indeed any!) cases. Consequently, I added some
comments in the hope that this condition will continue to be true.
Fixes: 5f7adb5b1c02 ("board_f: reserve noncached space below malloc area") Cc: Vikas Manocha <vikas.manocha@st.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Hou Zhiqiang [Tue, 27 Aug 2019 11:05:23 +0000 (11:05 +0000)]
MPC8548: dts: Added PCIe DT node
MPC8548 integrated a PCIe controllers, which is compatible with
the PCI Express™ Base Specification, Revision 1.0a, and this
patch is to add DT node for the PCIe controller.
Hou Zhiqiang [Tue, 27 Aug 2019 11:05:06 +0000 (11:05 +0000)]
P5040: dts: Added PCIe DT nodes
P5040 integrated 3 PCIe controllers, which is compatible with
the PCI Express™ Base Specification, Revision 2.0, and this
patch is to add DT node for each PCIe controller.
Hou Zhiqiang [Tue, 27 Aug 2019 11:04:56 +0000 (11:04 +0000)]
P4080: dts: Added PCIe DT nodes
P4080 integrated 3 PCIe controllers, which is compatible with
the PCI Express™ Base Specification, Revision 2.0, and this
patch is to add DT node for each PCIe controller.
Hou Zhiqiang [Tue, 27 Aug 2019 11:04:42 +0000 (11:04 +0000)]
P3041: dts: Added PCIe DT nodes
P3041 integrated 4 PCIe controllers, which is compatible with
the PCI Express™ Base Specification, Revision 2.0, and this
patch is to add DT node for each PCIe controller.
Hou Zhiqiang [Tue, 27 Aug 2019 11:04:29 +0000 (11:04 +0000)]
P2041: dts: Added PCIe DT nodes
P2041 integrated 3 PCIe controllers, which is compatible with
the PCI Express™ Base Specification, Revision 2.0, and this
patch is to add DT node for each PCIe controller.
Hou Zhiqiang [Tue, 27 Aug 2019 11:04:15 +0000 (11:04 +0000)]
P2020: dts: Added PCIe DT nodes
P2020 integrated 3 PCIe controllers, which is compatible with
the PCI Express™ Base Specification, Revision 1.0a, and this
patch is to add DT node for each PCIe controller.
Hou Zhiqiang [Tue, 27 Aug 2019 11:04:04 +0000 (11:04 +0000)]
P1020: dts: Added PCIe DT nodes
P1020 integrated 2 PCIe controllers, which is compatible with
the PCI Express™ Base Specification, Revision 1.0a, and this
patch is to add DT node for each PCIe controller.
Hou Zhiqiang [Tue, 27 Aug 2019 11:03:47 +0000 (11:03 +0000)]
t104x: dts: Added PCIe DT nodes
T104x integrated 4 PCIe controllers, which is compatible with
the PCI Express™ Base Specification, Revision 2.0, and this
patch is to add DT node for each PCIe controller.
Hou Zhiqiang [Tue, 27 Aug 2019 11:03:27 +0000 (11:03 +0000)]
t102x: dts: Added PCIe DT nodes
T102x integrated 3 PCIe controllers, which is compatible with
the PCI Express™ Base Specification, Revision 2.0, and this
patch is to add DT node for each PCIe controller.
Hou Zhiqiang [Tue, 27 Aug 2019 11:03:10 +0000 (11:03 +0000)]
t4240: dts: Added PCIe DT nodes
T4240 integrated 4 PCIe controllers, which is compatible with
the PCI Express™ Base Specification, Revision 3.0, and this
patch is to add DT node for each PCIe controller.
Hou Zhiqiang [Tue, 27 Aug 2019 10:13:54 +0000 (10:13 +0000)]
dm: pcie_fsl: Fix the calculation of controller index
The PCIe controller register address in CCSR is different
on various platforms, the current code erroneously use
the hardcoded address (0xffe240000) and stride (0x10000)
to calculate the controller's index.
Fix it by adding the related info to the driver data
structure.
Hou Zhiqiang [Tue, 27 Aug 2019 10:13:48 +0000 (10:13 +0000)]
dm: pcie_fsl: Convert IS_ENABLED() run-time checking to #ifdef
This can avoid build error:
The macro in brackets of the IS_ENABLED(CONFIG_FOO) is only
defined on the platforms that select the CONFIG_FOO, while
it's not defined on platforms that do not select the
CONFIG_FOO.
Mark Kettenis [Tue, 27 Aug 2019 21:06:28 +0000 (23:06 +0200)]
clk: meson-g12b: add compatible
The G12B clock controller is almost identical to the G12A and
so far the differences don't matter. Adding the G12B compatible
makes USB work on the Odroid-N2.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Support of device tree model for T2080RDB, T4240RDB, T1024RDB,
T1042D4RDB, P1020RDB, P2020RDB, P2041RDB, P3041DS, P4080DS, P5040DS and
MPC8548CDS. Also support of i2c dm model.
Tom Rini [Tue, 27 Aug 2019 11:09:10 +0000 (07:09 -0400)]
Merge tag 'for-v2019.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c
i2c bugfixes for 2019.10
- misc: i2c_eeprom: verify that the chip is functional at probe()
- i2c: mxc_i2c: Remove i2c_idle_bus from probe
- i2c-mux-gpio: Fix GPIO request flag issue
Add example of its files to generate FIT to start kernel
on ev1 or dk2 board with
- only kernel and dtb = fit_copro_kernel_dtb.its
- kernel, M4 copro firmware and dtb = it_copro_kernel_dtb.its
Add extlinux example to manage config in generated FIT.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
projects / u-boot.git / log