Tom Rini [Sun, 10 Feb 2019 13:04:53 +0000 (08:04 -0500)]
Merge branch '2019-02-08-master-imports'
- bcm6345 watchdog, bcm63158/bcm963158 initial support.
- Various TI platform resyncs and improvements.
- FDT support in Android-format images.
- stm32mp1 improvements.
arm: mach-k3: common: Clean up ATF image startup function
Perform some cosmetic cleanup of the ATF image startup function, namely
fixing a spelling mistake, capitalization of a few words, spacing, as
well aligning how errors are printed and as using panic() for cases that
were using a combination of printf() + hang().
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Alexander Graf [Thu, 31 Jan 2019 15:06:23 +0000 (16:06 +0100)]
initcall: Move to inline function
The board_r init function was complaining that we are looping through
an array, calling all our tiny init stubs sequentially via indirect
function calls (which can't be speculated, so they are slow).
The solution to that is pretty easy though. All we need to do is inline
the function that loops through the functions and the compiler will
automatically convert almost all indirect calls into direct inlined code.
With this patch, the overall code size drops (by 40 bytes on riscv64)
and boot time should become measurably faster for every target.
Errata i929 in certain OMAP5/DRA7XX/AM57XX silicon revisions
(SPRZ426D - November 2014 - Revised February 2018 [1]) mentions
unexpected tuning pattern errors. A small failure band may be present
in the tuning range which may be missed by the current algorithm.
Furthermore, the failure bands vary with temperature leading to
different optimum tuning values for different temperatures.
As suggested in the related Application Report (SPRACA9B - October 2017
- Revised July 2018 [2]), tuning should be done in two stages.
In stage 1, assign the optimum ratio in the maximum pass window for the
current temperature. In stage 2, if the chosen value is close to the
small failure band, move away from it in the appropriate direction.
Patrick Delaunay [Wed, 30 Jan 2019 12:07:05 +0000 (13:07 +0100)]
dts: stm32mp1: clock tree update
- Add st,digbypass on clk_hse node (needed for board rev.C)
- MLAHB/AHB max frequency increased from 200 to 209MHz, with:
- PLL3P set to 208.8MHz for MCU sub-system
- PLL3Q set to 24.57MHz for 48kHz SAI/SPI2S
- PLL3R set to 11.29MHz for 44.1kHz SAI/SPI2S
- PLL4P set to 99MHz for SDMMC and SPDIFRX
- PLL4Q set to 74.25MHz for EVAL board
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Vabhav Sharma [Wed, 30 Jan 2019 11:24:00 +0000 (11:24 +0000)]
drivers: serial: dm: Enable DM_FLAG_PRE_RELOC in SBSA pl011 uart driver
The DM_FLAG_PRE_RELOC shall be enabled in SBSA PL011 uart driver
as this driver is used in NXP based SoCs
It is necessary to have Serial console running before relocation
The !CONFIG_IS_ENABLED(OF_CONTROL) [*] check is set as "workaround"
for DM problem : 4687919684e
This flag is set if board does not support device-tree and using
platform data, In DM Model either of device tree or platform data
can be used to fetch device configuration
It is possible to use SBSA UART with CONFIG_DM_SERIAL but witout
corresponding device tree description (OF_CONTROL)
Other board/SoCs have this flag set unconditionally
Roman Kapl [Wed, 30 Jan 2019 10:39:54 +0000 (11:39 +0100)]
hashtable: fix environment variable corruption
Only first previously deleted entry was recognized, leading hsearch_r
to think that there was no previously deleted entry. It then conluded
that a free entry was found, even if there were no free entries and it
overwrote a random entry.
This patch makes sure all deleted or free entries are always found and
also introduces constants for the 0 and -1 numbers. Unit tests to excersise a
simple hash table usage and catch the corruption were added.
To trash your environment, simply run this loop:
setenv i 0
while true; do
setenv v_$i $i
setenv v_$i
setexpr i $i + 1
done
Chris Packham [Wed, 30 Jan 2019 07:23:16 +0000 (20:23 +1300)]
moveconfig: add a second pass for empty #if/#endif blocks
Moveconfig already attempts to remove empty #if/#endif blocks when there
is a matching CONFIG_ being moved. Add a second pass which covers files
without a match.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Chris Packham [Wed, 30 Jan 2019 07:19:28 +0000 (20:19 +1300)]
omap3_cairo: remove empty #ifdef/#endif block
The content between these guards was removed in commit 9baa2bce2890
("Removed unused references to CONFIG_SERIALx"). Remove the now
empty #ifdef/#endif block and the accompanying comment.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Shawn Guo [Tue, 15 Jan 2019 14:26:37 +0000 (22:26 +0800)]
fdt: support booting with dtb in Android image
Some platforms choose to store device tree blob in Android image second
area. Let's try to look for dtb from there when booting an Android
image, and use it for booting if found.
Vignesh R [Tue, 5 Feb 2019 05:59:29 +0000 (11:29 +0530)]
MAINTAINERS: Add an entry for SPI NOR
Add myself as co-maintainer for U-Boot SPI NOR subsystem.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: drop mtd/spi file from SPI entry] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Vignesh R [Tue, 5 Feb 2019 05:59:28 +0000 (11:29 +0530)]
configs: Don't use SPI_FLASH_BAR as default
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:27 +0000 (11:29 +0530)]
configs: Remove SF_DUAL_FLASH
SF_DUAL_FLASH claims to enable support for SF_DUAL_STACKED_FLASH and
SF_DUAL_PARALLEL_FLASH. But, in current U-Boot code, grepping for above
enums yield no user and therefore support seems to be incomplete. Remove
these configs so as to avoid confusion.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:26 +0000 (11:29 +0530)]
spl: Kconfig: Enable SPI_FLASH_TINY by default for SPL
SPL only needs to be able to read from SPI Flash to load next stage and
does not really need write/erase etc. Therefore in order to reduce SPI
Flash code size in SPL, enable SPI_FLASH_TINY, that only supports
reading from SPI flash, as default.
Note: Since, SPI_FLASH_TINY does not support SPI_FLASH_BAR,
SPI_FLASH_TINY is not enabled for boards with SPI controllers that
cannot support 4 byte addressing.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:25 +0000 (11:29 +0530)]
mtd: spi: Add lightweight SPI flash stack for SPL
Add a tiny SPI flash stack that just supports reading data/images from
SPI flash. This is useful for boards that have SPL size constraints and
would need to use SPI flash framework just to read images/data from
flash. There is approximately 1.5 to 2KB savings with this.
Based on prior work of reducing spi flash id table by
Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:24 +0000 (11:29 +0530)]
mtd: spi: Remove unused files
spi_flash and spi_flash_ids are no longer needed after SPI NOR
migration. Remove them.
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:23 +0000 (11:29 +0530)]
mtd: spi: Switch to new SPI NOR framework
Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD
layer. Fix up sf_dataflash to work in legacy way. And update sandbox to
use new interfaces/definitions
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Linux uses "jedec,spi-nor" as compatible string for JEDEC compatible
SPI Flash device nodes. Therefore make U-Boot also to look for the same
compatible string so that we can use Linux DTS files as is.
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:21 +0000 (11:29 +0530)]
mtd: spi: spi-nor-core: Add back U-Boot specific features
For legacy reasons, we will have to keep around U-Boot specific
SPI_FLASH_BAR and SPI_TX_BYTE. Add them back to the new framework
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:20 +0000 (11:29 +0530)]
mtd: spi: spi-nor-core: Add SFDP support
Sync Serial Flash Discoverable Parameters (SFDP) parsing support from
Linux. This allows auto detection and configuration of Flash parameters.
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:19 +0000 (11:29 +0530)]
mtd: spi: spi-nor-core: Add 4 Byte addressing support
Sync changes from Linux SPI NOR framework to add 4 byte addressing
support. This is required in order to support flashes like MT35x
that no longer support legacy Bank Address Register(BAR) way of accessing
>16MB region.
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:18 +0000 (11:29 +0530)]
mtd: spi: spi-nor-core: Add SPI MEM support
Many SPI controllers have special MMIO interfaces which provide
accelerated read/write access but require knowledge of flash parameters
to make use of it. Recent spi-mem layer provides a way to support such
controllers.
Therefore, add spi-mem support to spi-nor-core as a way to support SPI
controllers with MMIO interface. SPI MEM layer takes care of translating
spi_mem_ops to spi_xfer()s in case of legacy SPI controllers.
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:17 +0000 (11:29 +0530)]
mtd: spi: Port SPI NOR framework from Linux
Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not
support 4 byte addressing opcodes, SFDP table parsing and different types of
quad mode enable sequences. Many newer flashes no longer support BANK
registers used by sf layer to a access >16MB of flash address space.
So, sync SPI NOR framework from Linux v4.19 that supports all the
above features. Start with basic sync up that brings in basic framework
subsequent commits will bring in more features.
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:15 +0000 (11:29 +0530)]
spi: Add non DM version of SPI_MEM
Add non DM version of SPI_MEM to support easy migration to new SPI NOR
framework. This can be removed once DM_SPI conversion is complete.
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:14 +0000 (11:29 +0530)]
spi: spi-mem: Claim SPI bus before spi mem access
It is necessary to call spi_claim_bus() before starting any SPI
transactions and this restriction would also apply when calling spi-mem
operations. Therefore claim and release bus before requesting transfer
via exec_op.
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:13 +0000 (11:29 +0530)]
spi: spi-mem: Extend spi_mem_adjust_op_size() to honor max xfer size
Extend spi_mem_adjust_op_size() to take spi->max_write_size and
spi->max_read_size into account.
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:12 +0000 (11:29 +0530)]
spi: spi-mem: Allow use of spi_mem_exec_op for all SPI modes
SPI controllers support all types of SPI modes including dual/quad bus
widths. Therefore remove constraint wrt SPI mode from spi-mem layer.
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Vignesh R [Tue, 5 Feb 2019 05:59:11 +0000 (11:29 +0530)]
bitops: Fix GENMASK definition for Sandbox
In arch/sandbox/include/asm/types.h we have
Therefore for 32 bit Sandbox build BITS_PER_LONG turns out to be 32 as
CONFIG_PHYS64 is not set
This messes up the current logic of GENMASK macro due to mismatch b/w
size of unsigned long (64 bit) and that of BITS_PER_LONG.
Fix this by using CONFIG_SANDBOX_BITS_PER_LONG which is set to 64/32
based on the host machine on which its being compiled.
Without this patch:
GENMASK(14,0) => 0x7fffffffffff
After this patch:
GENMASK(14,0) => 0x7fff
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Vignesh R [Tue, 5 Feb 2019 05:59:10 +0000 (11:29 +0530)]
configs: Move CONFIG_SPI_FLASH into defconfigs
Completely move CONFIG_SPI_FLASH from remaining board header files to
defconfigs
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
commit fdce9d35dc36 ("arm: dts: am33xx: Sync dts with Linux 4.20.0")
did remove the "u-boot,dm-spl" flag from the 'ocp' bus which was
introduced with
commit 19aa4ac09db9 ("dts: am33xx: add u-boot, dm-spl to ocp bus")
Due to this all boards having CONFIG_SPL_OF_CONTROL enabled are broken
because they cannot bind/probe the boot-media interface during SPL
stage.
This commit introduces the 'am33xx-u-boot.dtsi' which is included with
the auto include mechanism. The am33xx-u-boot-dtsi adds the important
"u-boot,dm-pre-reloc" to the 'ocp bus' (the root bus of almost all
peripherals, at least the bootable ones).
The peripherials (mmc, spi, ...) needed during SPL stage need to be
equipped with the 'u-boot,dm-pre-reloc' in their responsible dts file.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Tom Rini [Tue, 5 Feb 2019 13:37:21 +0000 (08:37 -0500)]
Merge git://git.denx.de/u-boot-marvell
- Move Armada XP / 38x PCIe driver to DM_PCI from me
- Move Armada XP / 38x LCD driver to DM_VIDEO from me
- Add uDPU board (Armada-3720) from Vladimir
[trini: Fix warning in pci-uclass.c by removing ret from
pci_uclass_child_post_bind as it no longer calls functions with
a return code to catch.] Signed-off-by: Tom Rini <trini@konsulko.com>II
Stefan Roese [Wed, 30 Jan 2019 07:54:13 +0000 (08:54 +0100)]
arm: mvebu: theadorable: Enable video / LCD support with the new DM driver
With the new DM_VIDEO support in the Armada XP LCD driver, this patch
adds the needed DT node for the LCD controller to the theadorable dts
file. This DT property is not added to the Armada XP dtsi files, as this
LCD feature is pretty unusual for this SoC and I personally know of no
other board that uses this controller.
This patch also enables CONFIG_BMP_16BPP/24BPP/32BPP, as the "old" bmp
command supported these BMP files.
Stefan Roese [Wed, 30 Jan 2019 07:54:11 +0000 (08:54 +0100)]
video: Armada XP: Move driver to DM_VIDEO
This patch moves the Armada XP video / LCD driver to DM_VIDEO. With this
move, the legacy interface board_video_init() is removed from the
theadorable board code (only user of this video driver). The support
via DT will be added in a separate patch.
This patch also enables DM_VIDEO for the theadorable board, as this is
needed to not break git bisect'ability.
Vladimir Vid [Mon, 28 Jan 2019 16:27:58 +0000 (17:27 +0100)]
arm64: mvebu: Add basic support for uDPU board
This adds initial support for micro-DPU (uDPU) board which is based on Armada-3720 SoC.
micro-DPU is the single-port FTTdp "distribution point unit" made by Methode Electronics
which offers complete modularity with replaceable SFP modules both for uplink and downlink
(G.hn over twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable).
On-board features:
- 512 MiB DDR3
- 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC
- USB 2.0 Type-C connector
- 4GB eMMC
- ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type)
Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Luis Torres <luis.torres@methode.com> Cc: Scott Roberts <scott.roberts@telus.com> Cc: Paul Arola <paul.arola@telus.com> Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Now that the PCIe driver supports DM and DT parsing, enable the PCIe DT
nodes that are used by this board.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Phil Sutter <phil@nwl.cc> Cc: Marek Behún <marek.behun@nic.cz> Cc: VlaoMao <vlaomao@gmail.com>
Stefan Roese [Fri, 25 Jan 2019 10:52:44 +0000 (11:52 +0100)]
arm: mvebu: armada-xp/37x.dtsi: Sync PCIe DT nodes with Linux v4.20
This patch sync's the PCIe DT nodes with the recent Linux v4.20 version.
This change makes it easier to reference specific PCIe nodes in the
board dts files to e.g. enable a PCIe port as this is now necessary with
the new DM PCI driver for these platforms.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Phil Sutter <phil@nwl.cc> Cc: Marek Behún <marek.behun@nic.cz> Cc: VlaoMao <vlaomao@gmail.com> Cc: Tom Rini <trini@konsulko.com>
Stefan Roese [Fri, 25 Jan 2019 10:52:43 +0000 (11:52 +0100)]
pci: pci_mvebu: Add DM_PCI support and move CONFIG_PCI_MVEBU to defconfig
This patch adds DM_PCI support to the MVEBU PCIe driver. This is
necessary, since all PCI drivers have to be moved to DM (driver model)
until the v2019.07 release.
To not break git bisect'ablility, this patch also moves CONFIG_PCI_MVEBU
from config headers to the defconfig files.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Phil Sutter <phil@nwl.cc> Cc: Marek Behún <marek.behun@nic.cz> Cc: VlaoMao <vlaomao@gmail.com>
Stefan Roese [Fri, 25 Jan 2019 10:52:42 +0000 (11:52 +0100)]
pci: Add pci_get_devfn() to extract devfn from the fdt_pci_addr
This function will be used by the Marvell Armada XP/38x PCIe driver,
which is moved to DM right now. So let's extract the functionality
from pci_uclass_child_post_bind() to make it available.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Sat, 2 Feb 2019 15:11:20 +0000 (10:11 -0500)]
Merge tag 'for-master-20190201' of git://git.denx.de/u-boot-rockchip
u-boot-rockchip changes for 2019.04-rc1:
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
Tom Rini [Sat, 2 Feb 2019 15:08:50 +0000 (10:08 -0500)]
Merge branch '2019-02-01-master-imports'
- Various TI platforms have been updated and DTS files re-synced and
options disabled if not used or migrated to the DM versions
- Improvements to the dumpimage tool
- Rename SPL FAT/EXT filesystem support symbols for consistency and then
allow them to be used to save more space in SPL.
- More lmb fixes
- Partial migration of CONFIG_BUILD_TARGET
This fixes the automatic lmb initialization and reservation for boards
with more than one DRAM bank.
This fixes the CVE-2018-18439 and -18440 fixes that only allowed to load
files into the firs DRAM bank from fs and via tftp.
Found-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Martyn Welch [Sat, 26 Jan 2019 02:31:54 +0000 (02:31 +0000)]
tools: dumpimage: Clarify help
Help message isn't clear over the use of the "-T" option (it's to declare
the type of image that the tool is operating on), which also is optional
as it defaults to the default image type. It's also missing a description
of the "-o" option, so add it.
Martyn Welch [Sat, 26 Jan 2019 02:31:53 +0000 (02:31 +0000)]
tools: dumpimage: Add help option and make error paths consistent
The utility dumpimage has error paths that display the usage and others
that exit without displaying usage. Add an explicit help option to
dumpimage to display the usage and remove it's use in error paths to make
the error messages more obvious and errors paths more consistent.
Martyn Welch [Sat, 26 Jan 2019 02:31:51 +0000 (02:31 +0000)]
tools: dumpimage: Simplify arguments
The dump image utility has very confusing syntax. If called to list image
contents ("-l") it takes the image name as a positional argument. If the
utility is called to extract something from the image, the image must be
provided via the optional argument "-i" as well as the positional argument
but the value passed in the positional argument will be completely
ignored.
Simplify dumpimage by always providing the image as the first positional
argument. Assume we want to dump something from the image if we do not
provide the "-l" option for now.
Martyn Welch [Sat, 26 Jan 2019 02:31:50 +0000 (02:31 +0000)]
tools: dumpimage: Provide more feedback on error
The dumpimage utility errors out in a number of places without providing
sufficient feedback to allow the user to easily determine what they have
done wrong. Add addtional error messages to make the cause of the failure
more obvious.
Adam Ford [Thu, 24 Jan 2019 20:33:36 +0000 (14:33 -0600)]
regulator: pbias: Handle extended drain IO when changing omap36 PBIAS
The OMAP36 and DM37 TRM state to disable extneded drain IO before
changing the PBIAS. This patch does this before pmic writes if
the CONFIG_MMC_OMAP36XX_PINS flag is set and the cpu family is
omap36xx
As we're working on the next update of our ATF (and U-Boot and the ATF
are out-of-sync), let's temporarily enable SPL_ATF_NO_PLATFORM_PARAM to
reduce compatibility issues.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Fri, 1 Feb 2019 14:15:38 +0000 (15:15 +0100)]
pinctrl: Kconfig: fix missing include of rockchip/Kconfig
After the merge of the new, generic pinctrl-code, the include for
rockchip/Kconfig was missing. Add it here, so we can select the
pinctrl-driver for SPL.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Fri, 1 Feb 2019 08:34:06 +0000 (09:34 +0100)]
rockchip: Add MAINTAINER entry for chromebook_speedy
This adds a MAINTAINER entry for chromebook_speedy.
Without this, we get the following warnings from the maintainers
check:
WARNING: no status info for 'chromebook_minnie'
WARNING: no maintainers for 'chromebook_minnie'
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Simon Glass [Mon, 21 Jan 2019 21:53:36 +0000 (14:53 -0700)]
rockchip: Add support for chromebook_bob
Bob is a 10-inch chromebook produced by Asus. It has two USB 3.0 type-C
ports, 4GB of SDRAM, WiFi and a 1280x800 display. It uses its USB ports
for both power and external display. It includes a Chrome OS EC
(Cortex-M3) to provide access to the keyboard and battery functions.
Support so far includes only:
- UART
- SDRAM
- MMC, SD card
- Cros EC (but not keyboard)
Not included:
- Keyboard
- Display
- Sound
- USB
- TPM
Bob is quite similar to Kevin, the Samsung Chromebook Plus, but support
for this is not provided in this series.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Simon Glass [Mon, 21 Jan 2019 21:53:34 +0000 (14:53 -0700)]
rockchip: Implement spl_gpio in the GPIO driver
Allow rockchip boards to use GPIOs before driver model is ready. This is
really only useful for setting GPIOs to enable the early debug console, if
needed on some platforms.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Simon Glass [Mon, 21 Jan 2019 21:53:33 +0000 (14:53 -0700)]
rockchip: Move pull-up/down enum into a common file
At present this enum is only available to rk3288. Move it so that other
rockchip SoCs can access it. It is needed for the SPL GPIO driver for
rk3999 in a later patch.
Also adjust the enum name to lower case.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
projects / u-boot.git / log