Marek Vasut [Sat, 22 Sep 2018 02:13:35 +0000 (04:13 +0200)]
fs: btrfs: Fix cache alignment bugs
The btrfs implementation passes cache-unaligned buffers into the
block layer, which triggers cache alignment problems down in the
block device drivers. Align the buffers to prevent this.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Behun <marek.behun@nic.cz>
Ramon Fried [Fri, 21 Sep 2018 10:35:53 +0000 (13:35 +0300)]
usb: ehci-msm: Add init_after_reset for CI_UDC
MSM uses the chipidea controller IP, however it requires
to reinit the phy after controller reset. in EHCI mode there's a
dedicated callback for it.
In device mode however there's no such callback.
Add implementaion of ci_init_after_reset() to implement the above
requirement in case CI_UDC driver is used.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:52 +0000 (13:35 +0300)]
usb:ci_udc: Introduce init_after_reset phy function
MSM variant of Chipidea must reinitalize the phy
after controller reset.
Introduce ci_init_after_reset() weak function that
can be used to achieve the above init.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:47 +0000 (13:35 +0300)]
phy: db410c: Add MSM USB PHY driver
Add a PHY driver for the Qualcomm dragonboard 410c which
allows switching on/off and resetting the phy connected
to the EHCI controllers and USBHS controller.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
serial: serial_stm32: Enable uart FIFO for STM32F7xx SoCs
Since commit 7b3b74d32127 ("serial: serial_stm32: Enable overrun")
on STM32F7xx based boards, the first lines of serial output are
missing during boot (we no more see the U-Boot release version,
board model and DRAM size).
By enabling the uart FIFO on STM32F7, the complete U-boot log
can be sent correctly.
Neil Stainton [Wed, 19 Sep 2018 09:38:07 +0000 (10:38 +0100)]
u-boot: align cache flushes in load_elf_image_shdr to line boundaries
Prevent cache warning messages when using the 'bootelf' command on an
Arm target. Round down each section start address and round up the
respective section end to the nearest cache line.
Signed-off-by: Neil Stainton <nstainton@asl-control.co.uk>
[trini: Manually apply, rework whitespace] Signed-off-by: Tom Rini <trini@konsulko.com>
I tried building using a freshly built Make (4.2.1-69-g8a731d1), but
already the objtool build broke with
orc_dump.c: In function ‘orc_dump’:
orc_dump.c:106:2: error: ‘elf_getshnum’ is deprecated [-Werror=deprecated-declarations]
if (elf_getshdrnum(elf, &nr_sections)) {
Turns out that with that new Make, the backslash was not removed, so cpp
didn't see a #include directive, grep found nothing, and
-DLIBELF_USE_DEPRECATED was wrongly put in CFLAGS.
Now, that new Make behaviour is documented in their NEWS file:
* WARNING: Backward-incompatibility!
Number signs (#) appearing inside a macro reference or function invocation
no longer introduce comments and should not be escaped with backslashes:
thus a call such as:
foo := $(shell echo '#')
is legal. Previously the number sign needed to be escaped, for example:
foo := $(shell echo '\#')
Now this latter will resolve to "\#". If you want to write makefiles
portable to both versions, assign the number sign to a variable:
C := \#
foo := $(shell echo '$C')
This was claimed to be fixed in 3.81, but wasn't, for some reason.
To detect this change search for 'nocomment' in the .FEATURES variable.
This also fixes up the two make-cmd instances to replace # with $(pound)
rather than with \#. There might very well be other places that need
similar fixup in preparation for whatever future Make release contains
the above change, but at least this builds an x86_64 defconfig with the
new make.
clk: Add support for Arm's Versatile Express OSC clock generators
The Arm Versatile Express and Juno development boards contain an
OSC clock generator that can be accessed through the Versatile
Express config bus. The generators are quite often being controlled
by some MCU and the config bus offers a uniform way of exposing them.
Rajan Vaja [Wed, 19 Sep 2018 10:43:46 +0000 (03:43 -0700)]
dm: test: Add "/firmware" node scan test
Add a test which verifies that all subnodes under "/firmware"
nodes are scanned.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Added 'imply FIRMWARE' to sandbox Kconfig to fix test failures, fixed
ordering of lines in arch/sandbox/dts/test.dts and test/dm/Makefile,
updated #if condition in drivers/firmware/firmware-uclass.c: Signed-off-by: Simon Glass <sjg@chromium.org>
Rajan Vaja [Wed, 19 Sep 2018 10:43:43 +0000 (03:43 -0700)]
firmware: Add FIRMWARE config prompt string
There is no prompt string for FIRMWARE config. Without this,
FIRMWARE config cannot be enabled through menuconfing or
config file. Fix this by adding prompt summary.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 18 Sep 2018 05:55:42 +0000 (23:55 -0600)]
buildman: Avoid hanging when the config changes
Something has changed in the last several month such that when buildman
builds U-Boot incrementally and a new CONFIG option has been added to the
Kconfig, the build hanges waiting for input:
Test new config (NEW_CONFIG) [N/y/?] (NEW)
Since binamn does not connect the build's stdin to anything this waits on
stdin to the build thread, which never comes. Eventually I suspect all the
threads end up in this state and the build does not progress.
Fix this by passing /dev/null as input to the build. That way, if there is
a new CONFIG, the build will stop (and fail):
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
Drop period at end of commit subject: Signed-off-by: Simon Glass <sjg@chromium.org>
include/clk.h: Fix the name of the clock uclass in comment
The comment references a structure name that doesn't exist. Use
the name of the actual uclass.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
Drop period at end of commit subject: Signed-off-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Wed, 8 Aug 2018 20:10:44 +0000 (22:10 +0200)]
cmd: clk: Add trivial implementation of clock dump for DM
Add trivial implementation of the clk dump in case DM is enabled.
This implementation just iterates over all the clock registered
with the CLK uclass and prints their rate.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Mario Six [Tue, 31 Jul 2018 09:44:11 +0000 (11:44 +0200)]
drivers: Add board uclass
Since there is no canonical "board device" that can be used in board
files, it is difficult to use DM function for board initialization in
these cases.
Hence, add a uclass that implements a simple "board device", which can
hold devices not suitable anywhere else in the device tree, and is also
able to read encoded information, e.g. hard-wired GPIOs on a GPIO
expander, read-only memory ICs, etc. that carry information about the
hardware.
The devices of this uclass expose methods to read generic data types
(integers, strings, booleans) to encode the information provided by the
hardware.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Tue, 26 Jun 2018 06:46:50 +0000 (08:46 +0200)]
core: Add dev_{disable,enable}_by_path
We cannot use device structures to disable devices, since getting
them with the API functions would bind and activate the device, which
would fail if the underlying device does not exist. Reviewed-by: Simon Glass <sjg@chromium.org>
Mario Six [Tue, 26 Jun 2018 06:46:48 +0000 (08:46 +0200)]
core: Add functions to set properties in live-tree
Implement a set of functions to manipulate properties in a live device
tree:
* ofnode_write_prop() to set generic properties of a node
* ofnode_write_string() to set string properties of a node
* ofnode_set_enabled() to either enable or disable a node
Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 14 Sep 2018 10:57:36 +0000 (04:57 -0600)]
binman: Allow writing a map file when something goes wrong
When we get a problem like overlapping regions it is sometimes hard to
figure what what is going on. At present we don't write the map file in
this case. However the file does provide useful information.
Catch any packing errors and write a map file (if enabled with -m) to aid
debugging.
Simon Glass [Fri, 14 Sep 2018 10:57:34 +0000 (04:57 -0600)]
binman: Correct fmap output on x86
Normally x86 platforms use the end-at-4gb option. This currently produces
an FMAP with positions which have a large offset. The use of end-at-4gb is
a useful convenience within binman, but we don't really want to export
a map with these offsets.
Fix this by subtracting the 'skip at start' parameter.
Also put the code which convers names to fmap format, for clarity.
Simon Glass [Fri, 14 Sep 2018 10:57:33 +0000 (04:57 -0600)]
binman: Record the parent section of each section
At present sections have no record of their parent so it is not possible
to traverse up the tree to the root and figure out the position of a
section within the image.
Change the constructor to record this information.
Simon Glass [Fri, 14 Sep 2018 10:57:32 +0000 (04:57 -0600)]
binman: Support x86 microcode in TPL
When TPL is used on x86 we may want to program the microcode (at least for
the first CPU) early in boot. Add support for this by refactoring the
existing code to be more generic.
Simon Glass [Fri, 14 Sep 2018 10:57:31 +0000 (04:57 -0600)]
binman: Support hashing entries
Sometimesi it us useful to be able to verify the content of entries with
a hash. Add an easy way to do this in binman. The hash information can be
retrieved from the device tree at run time.
Simon Glass [Fri, 14 Sep 2018 10:57:28 +0000 (04:57 -0600)]
binman: Support adding files
In some cases it is useful to add a group of files to the image and be
able to access them at run-time. Of course it is possible to generate
the binman config file with a set of blobs each with a filename. But for
convenience, add an entry type which can do this.
Add required support (for adding nodes and string properties) into the
state module.
Simon Glass [Fri, 14 Sep 2018 10:57:26 +0000 (04:57 -0600)]
binman: Support compressed entries
Add support for compressing blob entries. This can help reduce image sizes
for many types of data. It requires that the firmware be able to
decompress the data at run-time.
Tom Rini [Sat, 29 Sep 2018 15:47:32 +0000 (11:47 -0400)]
Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
With DM enabled, this patch enables DM_SERIAL and removes
the NS16550 initialization from da850_lowlevel since the driver
will take care of that itself.
Adam Ford [Sun, 9 Sep 2018 21:12:11 +0000 (16:12 -0500)]
ARM: omap3_logic: Remove some manual pin-muxing
With the pinctrl function enabled and the device tree setting up
the pins we want to use, this patch removes the manual pinmuxing
except for that which is not done by the device tree and minimal
pins necessary for SPL (like serial, GPMC, and MMC)
Adam Ford [Sun, 9 Sep 2018 14:21:21 +0000 (09:21 -0500)]
ARM: am3517_evm: Enable TCA6416PW GPIO Expander
With DM_I2C and DM_GPIO working, this patch can enable the
GPIO expander on the I2C bus. This GPIO expander is connected
to some of the DIP switches and can now read the status of these
pins.
Adam Ford [Sun, 9 Sep 2018 12:25:30 +0000 (07:25 -0500)]
ARM: am3517_evm: Enable Pinctrl
The simple pinctrl driver currently available works with the omap3.
Enabling this will use the device tree to automatically set the
pin-muxing for various drivers.
Adam Ford [Sat, 8 Sep 2018 13:16:23 +0000 (08:16 -0500)]
mmc: omap_mmc: Remove invert references
With DM_GPIO and DM_MMC translating GPIO_ACTIVE_LOW, any boards
using the 'cd-invert' option will no longer need to do this. This
patch removes the support for 'invert' from the MMC driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Fix warning over when !DM_GPIO] Signed-off-by: Tom Rini <trini@konsulko.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:52 +0000 (10:35 +0300)]
configs: sama5d4_xplained: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:51 +0000 (10:35 +0300)]
configs: sama5d27_som1_ek: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:50 +0000 (10:35 +0300)]
configs: sama5d2_ptc_ek: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:49 +0000 (10:35 +0300)]
configs: sama5d3_xplained: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:48 +0000 (10:35 +0300)]
configs: sama5d2_xplained: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:42 +0000 (10:35 +0300)]
board: atmel: add support for pda detection
This adds the support for PDA detection as common code for
Atmel boards.
Using the one wire interface over GPIO , an EEPROM memory is read
and compared to preprogrammed values for PDA screens TM4300, TM7000
and TM7000B.
Once the PDA is detected, an environment variable is set accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:41 +0000 (10:35 +0300)]
configs: sama5d4_xplained: add onewire and eeprom drivers
SAMA5D4 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:40 +0000 (10:35 +0300)]
configs: sama5d2_ptc_ek: add onewire and eeprom drivers
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:39 +0000 (10:35 +0300)]
configs: sama5d27_som1_ek: add onewire and eeprom drivers
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:38 +0000 (10:35 +0300)]
configs: sama5d3_xplained: add onewire and eeprom drivers
SAMA5D3 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:37 +0000 (10:35 +0300)]
configs: sama5d2_xplained: add onewire and eeprom drivers
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Maxime Ripard [Tue, 18 Sep 2018 07:35:25 +0000 (10:35 +0300)]
w1: Add 1-Wire gpio driver
Add a bus driver for bitbanging a 1-Wire bus over a GPIO.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: fixed some issues] Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>