Kever Yang [Thu, 28 Mar 2019 03:01:24 +0000 (11:01 +0800)]
rockchip: correct ARCH_SOC name
The ARCH_SOC name default as 'rockchip' and we put all the
header file in 'arch/arm/include/asm/arch-rockchip/', but
the 'rockchip' is not the SOC name, let's correct it after
we update all the source file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsiich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Wed, 3 Apr 2019 07:28:16 +0000 (15:28 +0800)]
rockchip: add Kever Yang as co-custodian
This updates MAINTAINERS and git-mailrc to add me as a
co-custodian for rockchip
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Tom Rini <trini@konsulko.com>
Philipp Tomsich [Sun, 3 Feb 2019 15:17:33 +0000 (16:17 +0100)]
rockchip: spi: make optimised receive-handler unaligned-safe
To support unaligned output buffers (i.e. 'in' in the terminology of
the SPI framework), this change splits each 16bit FIFO element after
reading and writes them to memory in two 8bit transactions. With this
change, we can now always use the optimised mode for receive-only
transcations independent on the alignment of the target buffer.
Given that we'll run with caches on, the impact should be negligible:
as expected, this has no adverse impact on throughput if running with
a 960MHz LPLL configuration.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Sun, 3 Feb 2019 15:17:32 +0000 (16:17 +0100)]
rockchip: spi: add driver-data and a 'rxonly_manages_fifo' flag
The SPI controller's documentation (I only had access to the RK3399,
RK3368 and PX30 TRMs) specifies that, when operating in master-mode,
the controller will stop the SCLK to avoid RXFIFO overruns and TXFIFO
underruns. Looks like my worries that we'd need to support DMA-330
(aka PL330) to make any further progress were unfounded.
This adds a driver-data structure to capture hardware-specific
settings of individual controller instances (after all, we don't know
if all versions are well-behaved) and adds a 'master_manages_fifo'
flag to it. The first use of said flag is in the optimised
receive-only transfer-handler, which can now request 64Kframe
(i.e. 128KByte) bursts of data on each reprogramming of CTRLR1
(i.e. every time through the loop).
This improves throughput to 46.85MBit/s (a 94.65% bus-utilisation).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
For the RK3399-Q7 we recommend storing SPL and u-boot.itb in the
on-module 32MBit (and sometimes even larger, if requested as part of a
configure-to-order configuration) SPI-NOR flash that is clocked for a
bitrate of 49.5MBit/s and connected in a single-IO configuration (the
RK3399 only supports single-IO for SPI).
Unfortunately, the existing SPI driver is excruciatingly slow at
reading out large chunks of data (in fact it is just as slow for small
chunks of data, but the overheads of the driver-framework make it less
noticeable): before this change, the throughput on a 4MB read from
SPI-NOR is 8.47MBit/s which equates a 17.11% bus-utilisation.
To improve on this, this commit adds an optimised receive-only
transfer (i.e.: out == NULL) handler that hooks into the main transfer
function and processes data in 16bit frames (utilising the full with
of each FIFO element). As of now, the receive-only handler requires
the in-buffer to be 16bit aligned. Any lingering data (i.e. either if
the in-buffer was not 16-bit aligned or if an odd number of bytes are
to be received) will be handled by the original 8bit reader/wirter.
Given that the SPI controller's documentation does not guarantuee any
interlocking between the RXFIFO and the master SCLK, the transfer loop
will be restarted for each chunk of 32 frames (i.e. 64 bytes).
With this new receive-only transfer handler, the throughput for a 4MB
read increases to 36.28MBit/s (i.e. 73.29% bus-utilisation): this is a
4x improvement over the baseline.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reported-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Series-Cc: Klaus Goger <klaus.goger@theobroma-systems.com>
Series-Cc: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Philipp Tomsich [Sun, 3 Feb 2019 15:17:30 +0000 (16:17 +0100)]
rockchip: spi: only wait for completion, if transmitting
The logic in the main transmit loop took a bit of reading the TRM to
fully understand (due to silent assumptions based in internal logic):
the "wait until idle" at the end of each iteration through the loop is
required for the transmit-path as each clearing of the ENA register
(to update run-length in the CTRLR1 register) will implicitly flush
the FIFOs... transmisson can therefore not overlap loop iterations.
This change adds a comment to clarify the reason/need for waiting
until the controller becomes idle and wraps the entire check into an
'if (out)' to make it clear that this is required for transfers with a
transmit-component only (for transfers having a receive-component,
completion of the transmit-side is trivially ensured by having
received the correct number of bytes).
The change does not increase execution time measurably in any of my
tests.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Sun, 3 Feb 2019 15:17:29 +0000 (16:17 +0100)]
rockchip: spi: consistently use false/true with rkspi_enable_chip
While rkspi_enable_chip is called with true/false everywhere else in
the file, one call site uses '0' to denot 'false'.
This change this one parameter to 'false' and effects consistency.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Sun, 3 Feb 2019 15:17:28 +0000 (16:17 +0100)]
rockchip: spi: fix off-by-one in chunk size computation
The maximum transfer length (in a single transaction) for the Rockchip
SPI controller is 64Kframes (i.e. 0x10000 frames) of 8bit or 16bit
frames and is encoded as (num_frames - 1) in CTRLR1. The existing
code subtracted the "minus 1" twice for a maximum transfer length of
0xffff (64K - 1) frames.
While this is not strictly an error (the existing code is correct, but
leads to a bit of head-scrating), fix this off-by-one situation.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Sun, 3 Feb 2019 15:17:27 +0000 (16:17 +0100)]
rockchip: spi: remove unused code and fields in priv
Even though the priv-structure and the claim-bus function contain
logic for 16bit frames and for unidirectional transfer modes, neither
of these is used anywhere in the driver.
This removes the unused (as in "has no effect") logic and fields.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Sun, 3 Feb 2019 15:17:26 +0000 (16:17 +0100)]
rockchip: spi: add debug message for delay in CS toggle
In analysing delays introduced for large SPI reads, the absence of any
indication when a delay was inserted (to ensure the CS toggling is
observed by devices) became apparent.
Add an additional debug-only debug message to record the insertion and
duration of any delay (note that the debug-message will cause a delay
on-top of the delay-duration).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Sun, 3 Feb 2019 14:59:23 +0000 (15:59 +0100)]
rockchip: rk3399-puma: support Gigadevice SPI-NOR flash
Over the last quarter, a part of our production has used NOR flash
from Gigadevice in addition to the Winbond parts that we typically
source. This requires the SPI_FLASH_GIGADEVICE config to be set.
Enable SPI_FLASH_GIGADEVICE in the board's default defconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Tom Rini [Sat, 27 Apr 2019 15:34:55 +0000 (11:34 -0400)]
Revert "fs: btrfs: fix false negatives in ROOT_ITEM search"
Per Pierre this change shouldn't have been applied as it was superseded
by "fs: btrfs: fix btrfs_search_tree invalid results" which is also
applied now as 1627e5e5985d.
Igor Opaniuk [Tue, 9 Apr 2019 13:38:14 +0000 (15:38 +0200)]
avb: add support for named persistent values
AVB 2.0 spec. revision 1.1 introduces support for named persistent values
that must be tamper evident and allows AVB to store arbitrary key-value
pairs [1].
Introduce implementation of two additional AVB operations
read_persistent_value()/write_persistent_value() for retrieving/storing
named persistent values.
Correspondent pull request in the OP-TEE OS project repo [2].
Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Use _bss_start_ofs as the size of the boot loader code+data that we want
to protect in the flash. This replaces use of the no longer defined
_armboot_start.
Adam Ford [Wed, 17 Apr 2019 18:24:33 +0000 (13:24 -0500)]
ARM: da850evm: Fix TI boot scripts for MMC
The da850evm include environment/ti/mmc.h and places
DEFAULT_MMC_TI_ARGS, defined int that file, in
CONFIG_EXTRA_ENV_SETTINGS. This has been broken for some time
since neither CMD_PART nor CMD_UUID are available, so manually
changing the environmental variables was always required before
booting from MMC. With this patch, these scripts should work
again, and by default they point to mmc 0, partition 2, and
the dtb file exists in a /boot directory on partition 2.
Adam Ford [Wed, 17 Apr 2019 16:21:56 +0000 (11:21 -0500)]
ARM: da850evm: Fix broken SPI Flash
A previous patch converted a bunch of settings for CONFIG_SF_DEFAULT
but it broke the SPI Flash which now prevents booting. This patch
now correctly sets CONFIG_SF_DEFAULT_SPEED=30000000 to match what it
was before the conversion.
Fixes: 14453fbfadc2 ("Convert CONFIG_SF_DEFAULT_* to Kconfig") Signed-off-by: Adam Ford <aford173@gmail.com>
The match controller register is not cleared during
initialization. However, some bits of this register may reset the TC if
tnMRx match it.
As we can't make any assumption about how U-Boot is launched by the first
stage bootloader (such as S1L) clearing this register ensure that the
timers work as expected.
Since the introduction of the driver, some memory in IRAM is reserved for
the TX buffers.
However there are not used but instead of it, it is the buffer provided
by the net stack which is used. As stated in the comment of the driver,
not using the IRAM buffer could cause cache issue and lower the
throughput.
For the second argument it is less the case for transmitting buffers
because the throughput gain in IRAM is mitigated by the time to copy the
data from RAM to IRAM, but the first argument is still valid and indeed
this patch fixes issue seen with Ethernet on some boards
The purpose of "mtd: nand: raw: allow to disable unneeded ECC layouts"
was to allow disabling the default ECC layouts if a driver is known to
provide its own ECC layout. However, this commit did the opposite and
disabled the default layout when it was _not_ selected.
It breaks all the NAND drivers not providing their own ECC layout this
patch fix this situation.
Pierre Bourdon [Tue, 16 Apr 2019 00:47:14 +0000 (02:47 +0200)]
fs: btrfs: fix btrfs_search_tree invalid results
btrfs_search_tree should return the first item in the tree that is
greater or equal to the searched item.
The search algorithm did not properly handle the edge case where the
searched item is higher than the last item of the node but lower than
the first item of the next node. Instead of properly returning the first
item of the next node, it was returning an invalid path pointer
(pointing to a non-existent item after the last item of the node + 1).
This fixes two issues in the btrfs driver:
- Looking for a ROOT_ITEM could fail if it was the first item of its
leaf node.
- Iterating through DIR_INDEX entries (for readdir) could fail if the
first DIR_INDEX entry was the first item of a leaf node.
Signed-off-by: Pierre Bourdon <delroth@gmail.com> Cc: Marek Behun <marek.behun@nic.cz>
Pierre Bourdon [Sat, 13 Apr 2019 21:50:49 +0000 (23:50 +0200)]
fs: btrfs: fix false negatives in ROOT_ITEM search
ROOT_ITEMs in btrfs are referenced without knowing their actual "offset"
value. To perform these searches using only two items from the key, the
btrfs driver uses a special "btrfs_search_tree_key_type" function.
The algorithm used by that function to transform a 3-tuple search into a
2-tuple search was subtly broken, leading to items not being found if
they were the first in their tree node.
This commit fixes btrfs_search_tree_key_type to properly behave in these
situations.
Signed-off-by: Pierre Bourdon <delroth@gmail.com> Cc: Marek Behun <marek.behun@nic.cz>
Andrew F. Davis [Fri, 12 Apr 2019 16:54:47 +0000 (12:54 -0400)]
configs: Add configs for AM65x High Security EVM
Add new defconfig files for the AM65x High Security EVM.
This defconfigs are the same as for the non-secure part, except for:
CONFIG_TI_SECURE_DEVICE option set to 'y'
CONFIG_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_SPL_FIT_IMAGE_POST_PROCESS option set to 'y'
Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Andrew F. Davis [Fri, 12 Apr 2019 16:54:45 +0000 (12:54 -0400)]
arm: mach-k3: Add secure device support
K3 devices have High Security (HS) variants along with the non-HS already
supported. Like the previous generation devices (OMAP/Keystone2) K3
supports boot chain-of-trust by authenticating and optionally decrypting
images as they are unpacked from FIT images. Add support for this here.
Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Andrew F. Davis [Fri, 12 Apr 2019 16:54:42 +0000 (12:54 -0400)]
arm: K3: Avoid use of MCU_PSRAM0 before SYSFW is loaded
On HS devices the 512b region of reset isolated memory called
MCU_PSRAM0 is firewalled by default. Until SYSFW is loaded we
cannot use this memory. It is only used to store a single value
left at the end of SRAM by ROM that will be needed later. Save
that value to a global variable stored in the .data section.
This section is used as .bss will be cleared between saving
this value and using it.
Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
cmd: pxe: Display splashscreen from extlinux.conf input
The objective is to provide a simple way to retrieve a BMP file,
and display it as splashscreen, from extlinux.conf file input.
For this, we take example on https://www.syslinux.org/wiki/
index.php?title=Menu#The_advanced_menu_system
and more particularly on MENU BACKGROUND chapter.
For this, add "menu background" support in pxe command.
As example, extlinux.conf content will look like:
# Generic Distro Configuration file generated by OpenEmbedded
menu title Select the boot mode
TIMEOUT 20
menu background ../splash.bmp
DEFAULT stm32mp157c-ev1-sdcard
LABEL stm32mp157c-ev1-sdcard
KERNEL /uImage
FDT /stm32mp157c-ev1.dtb
APPEND root=/dev/mmcblk0p6 rootwait rw earlyprintk console=ttySTM0,115200
On many B&R boards we have a reset-controller, responsible for very
early board-bringup (voltages, clocks, ...) and bootmode selection.
To be ready for adding more B&R boards to source tree while avoiding
duplicate code, we add the resetcontroller implementation to the common
part of B&R boards.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Hannes Schmelzer [Wed, 10 Apr 2019 12:13:11 +0000 (14:13 +0200)]
board/BuR/common: prepare for compiling common into non AM33XX boards
Today the BuR common stuff is only used on AM33XX boards. In future we
plan to have many other platforms than AM33XX so we have to move arch-
specific #include(s) to responsible #ifdef sections. By the way we drop
unneeded #include(s).
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Tom Rini [Fri, 26 Apr 2019 17:50:00 +0000 (13:50 -0400)]
Merge git://git.denx.de/u-boot-marvell
- Add DM based generic watchdog start and reset implementation
and remove all ad-hoc implementations (Stefan)
- Move mv_sdhci to DM (Pierre)
- Misc turris_omnia updates (Pierre)
- Change openrd targets to correctly build again (size changes
and fixes to the dts targets) and bring it back into Travis
builds (Stefan)
- Add Kirkwood db-88f6281-bp board (Chris)
Stefan Roese [Thu, 25 Apr 2019 09:53:18 +0000 (11:53 +0200)]
arm: kirkwood: openrd: Mark openrd boards as maintained again
With the latest size increase of the openrd boards, they all compile
clean again. Let's mark them as maintained again and add the Travis
job.
Please note that I can only compile-test these targets as I don't
have access to one of those boards.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Albert ARIBAUD <albert-u-boot@aribaud.net> Cc: Vagrant Cascadian <vagrant@debian.org> Cc: Chris Packham <judge.packham@gmail.com> Cc: Tom Rini <trini@konsulko.com>
Stefan Roese [Thu, 11 Apr 2019 13:58:47 +0000 (15:58 +0200)]
watchdog: at91sam9_wdt: Remove now superfluous wdt start and reset
With the new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
The watchdog servicing is enabled via CONFIG_WATCHDOG.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Eugen Hristev <eugen.hristev@microchip.com>
Stefan Roese [Thu, 11 Apr 2019 13:58:46 +0000 (15:58 +0200)]
watchdog: mpc8xx_wdt: Watchdog driver and macros cleanup
With the generic watchdog driver now implemented, this patch removes
some legacy stuff from the MPC8xx watchdog driver and its Kconfig
integration. CONFIG_MPC8xx_WATCHDOG is completely removed and
hw_watchdog_reset() is made static, as the watchdog will now get
serviced via the DM infrastructure if enabled via CONFIG_WATCHDOG.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Stefan Roese [Thu, 11 Apr 2019 13:58:45 +0000 (15:58 +0200)]
watchdog: cadence: Remove driver specific "timeout-sec" handling
Now that we have a generic DT property "timeout-sec" handling, the
driver specific implementation can be dropped.
This patch also changes the timeout restriction to the min and max
values (clipping). Before this patch, the value provided via
"timeout-sec" was used if the parameter was too high or low. Now
the driver specific min and max values are used instead.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Stefan Roese [Thu, 11 Apr 2019 13:58:44 +0000 (15:58 +0200)]
watchdog: Implement generic watchdog_reset() version
This patch tries to implement a generic watchdog_reset() function that
can be used by all boards that want to service the watchdog device in
U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG.
Without this approach, new boards or platforms needed to implement a
board specific version of this functionality, mostly copy'ing the same
code over and over again into their board or platforms code base.
With this new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
This patch also adds a new flag to the GD flags, to flag that the
watchdog is ready to use and adds the pointer to the watchdog device
to the GD. This enables us to remove the global "watchdog_dev"
variable, which was prone to cause problems because of its potentially
very early use in watchdog_reset(), even before the BSS is cleared.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Marek Behún" <marek.behun@nic.cz> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Maxim Sloyko <maxims@google.com> Cc: Erik van Luijk <evanluijk@interact.nl> Cc: Ryder Lee <ryder.lee@mediatek.com> Cc: Weijie Gao <weijie.gao@mediatek.com> Cc: Simon Glass <sjg@chromium.org> Cc: "Álvaro Fernández Rojas" <noltari@gmail.com> Cc: Philippe Reynes <philippe.reynes@softathome.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Stefan Roese [Wed, 24 Apr 2019 14:05:06 +0000 (16:05 +0200)]
arm: mvebu: turris_omnia: Use thumb instructions in SPL to save space
With the latest changes to the drivers (SPI_FLASH_SPANSION etc), Travis
reports that the SPL image is too big. Let's use the thumb instructions
in SPL to save some space and make the image fit again.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Marek Behun <marek.behun@nic.cz> Reviewed-by: Marek Behún <marek.behun@nic.cz>
Stefan Roese [Thu, 11 Apr 2019 10:33:36 +0000 (12:33 +0200)]
arm: kirkwood: openrd: Increase U-Boot size in flash to make it fit
We have run now multiple times into size issues with the openrd
board port. To finally fix this, this patch now moves the U-Boot size
from 0x6.0000 to 0x8.0000, giving enough space for the next time.
This also changes the environment location and potentially the
MTD partitioning, but I see no better fix for now. Especially since
this board does not have an active maintainer.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Chris Packham <judge.packham@gmail.com> Reviewed-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Remove the superfluous CONFIG_ENV_ADDR definition. Its not needed
as CONFIG_ENV_OFFSET is also set to the same value.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Chris Packham <judge.packham@gmail.com> Reviewed-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds them to the Makefile to fix the build error.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Chris Packham <judge.packham@gmail.com> Reviewed-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Pierre Bourdon [Thu, 11 Apr 2019 02:56:58 +0000 (04:56 +0200)]
mmc: mv_sdhci: add driver model support
The new DM implementation currently does not support the Sheeva
88SV331xV5 specific quirk present in the legacy implementation. The
legacy code is thus kept for this SoC and others not yet migrated to
DM_MMC.
Signed-off-by: Pierre Bourdon <delroth@gmail.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Stefan Roese <sr@denx.de> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Commit c4bd12a7dad4 ("i2c: mux: Generate longer i2c mux name") changed
the naming scheme of i2c devices within a mux. This broke references to
i2c@0 in the Turris Omnia board initialization code.
Signed-off-by: Pierre Bourdon <delroth@gmail.com> Cc: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Marek Behún <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
arm: socfpga: mailbox: Fix off-by-one error on command length checking
A mailbox command contains 1-u32 header + arguments. The "len" variable
only contains the length of the arguments, but not the 1-u32 header.
Include the length of header when checking the ring buffer space to
prevent off-by-one error.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Remove outdated defines (not used any more, outdated due to DM
conversion) from various socfpga files in include/config.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
Series-version: 3
Series-changes: 2
- added (this) patch with further cleanups to the socfpga board config
files
socfpga_common.h defines CONFIG_SYS_BOOTMAPSZ to 64 MiB.
Since having this define overrides the 'bootm_size' env variable for
the whole socfpga platform, let's remove this define from socfpga_common.h
and instead rely on the 'bootm_size' env variable (which is initialized
to 160 MiB in the same file's default env). This gives users the
chance to override it in their own environment.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Marek Vasut <marex@denx.de> Series-to: Marek Vasut <marex@denx.de> Series-to: u-boot@lists.denx.de
Cover-letter:
arm: socfpga: clean up socfpga_common.h
This series cleans up the include/configs/socfpga_common.h file a bit.
It removes some defines that are used nowhere and cleans up some
leftovers after various subsystems have been converted to use DM.
END
All socfpga boards except for vining_fpga use DM_I2C. Enable
DM_I2C for this board and set the EEPROM defines via Kconfig
(enabling CONFIG_I2C_EEPROM from MISC).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Series-changes: 2
- added (this) patch to move socfpga_vining to DM_I2C
By enabling debug prints in malloc_simple, we can see that SPL for socfpga
gen5 does by far not need the 8 KiB malloc pool currently allocated for
SPL in pre-reloc phase.
On socfpga_socrates, 1304 bytes are currently used (and this increases by
~200 bytes only for the sdram/reset fixes in socfpga-next).
To prevent wasting precious SRAM space, let's reduce the initial heap used
for SPL to 2 KiB. This is still some hundred bytes more than currently
used. Also, the gen5 SPL enables stack and heap in DDR memory pretty
early. Only the initial uclass/dm parsing, serial console and DDR
initialization is done in the initial heap, so these 2 KiB should be
enough for all boards.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
This commit moves common config options used in all socfpga boards
to select/imply in Kconfig. This both cleans up the defconfig files
as well as makes future changes easier.
Options implied/defaulted for all sub-arches:
- SPL, SPL_DM, USE_TINY_PRINTF, NR_DRAM_BANKS
Options implied/defaulted for implied for A10 & gen5:
- FPGA_SOCFPGA, SYS_MALLOC_F_LEN, SYS_TEXT_BASE
Options implied/defaulted for gen5:
- SPL_STACK_R, SPL_SYS_MALLOC_SIMPLE, SPL_STACK_R_ADDR
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
If SPL post-reloc stage puts the stack into DDR, U-Boot should be able to
do that, too.
The reason to do so is that this way, U-Boot initial stack can be larger
than SPL initial stack. In situations where we want to save the SPL
in SRAM for next boot without reloading, this prevents overwriting the
SPL DTB in SRAM if U-Boot stack usage gets too high.
To achieve this, the malloc definition for a10 is moved up and sligthly
changed to ensure CONFIG_SYS_INIT_RAM_SIZE is the remaining available size.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
The comment about SPL memory layout for socfpga gen5 is outdated: the
initial malloc memory is now at the end of the SRAM, gd is below it
(see board_init_f_alloc_reserve).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
This patch makes the on-board RTC work on the socfpga_socrates board.
This rtc is present on the board, but it does not work (fails with a
timeout).
This patch adds a weak pull-up on the I2C0-SCL pin connected to the m41t82
RTC on this board. While the SDA line has a pull-up on the pcb, the pull-up
on the SCL line seems to be missing. To work around this, enable the
weak-pull-up feature on this pin.
After applying this patch, the rtc timeout is gone and the 'date' command
can access the rtc chip.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
This adds a compatible string for m41t82. This ensures that this driver
can be used for m41t82 in DM mode, too (asit was usable for this model in
non-DM mode before).
In addition, the HT bit has to be reset during probe, since the m41t82
chip sets it when entering battery standby mode.
This patch ensures this driver works on socfpga_socrates.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
i2c: designware: fix reset handling on socfpga gen5
Using this driver on socfpga gen5 with DM_I2C enabled leads to a data abort
as the 'i2c' reset property cannot be found (the gen5 dtsi does not provide
reset-names).
The actual bug was to check 'if (&priv->reset_ctl)', which is never false.
While at it, convert the driver to use 'reset_get_bulk' instead of looking
at a specific named reset and also make it release the reset on driver
remove before starting the OS.
Fixes: 622597dee4f6 ("i2c: designware: add reset ctrl to driver") Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de>
The 'eeprom' command has been converted to work with DM_I2C in a patch
submitted around the same time as this commit:
commit 0c07a9b4078d ("eeprom: Add device model based I2C support to eeprom command")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
Tom Rini [Wed, 24 Apr 2019 16:26:58 +0000 (12:26 -0400)]
Merge tag 'efi-2019-07-rc1-3' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc1 (3)
This patch series reworks the implementation of the `bootefi` command to
remove code duplication by using the LoadImage() boot service to load
binaries.
Missing short texts for UEFI protocols are added for display by the
`efidebug dh` command.
Missing parameter checks for AllocatePages() and CreateDeviceNode() are
implemented.
The constants for protocol GUIDs are changed to match the names in the UEFI
specification.
Tom Rini [Wed, 24 Apr 2019 16:26:25 +0000 (12:26 -0400)]
Merge tag 'u-boot-amlogic-20190423' of git://git.denx.de/u-boot-amlogic
- Add support for Amlogic p200 & p201 Reference Designs
- Add Amlogic SoC information display
- Add support for the Libretech-AC AML-S805X-AC board
- Add Amlogic AXG reset compatible
- Add I2C support for Amlogic AXG
- Fix AXG PIN and BANK pinctrl definitions
- Fix regmap_read_poll_timeout warning about sandbox_timer_add_offset
- Add initial support for Amlogic G12A SoC and U200 board
- Enable PHY_REALTEK for selected boards
- Fix Khadas VIM2 README
Tom Rini [Wed, 24 Apr 2019 13:04:23 +0000 (09:04 -0400)]
Merge branch '2019-04-22-master-imports'
- Add and enable brcmnand driver on a number of relevant platforms.
Also add and enable LED drivers on more bcm platforms.
- Various ARMv8 fixes/improvements, including extending PSCI
functionality.
- fs_loader improvments
- Various FIT/SPL improvements
- PCI bugfixes
- Poplar platform ethernet support
- MediaTek MMC improvements
- Android boot improvements
According to Android image format [1], kernel image resides at 1 page
offset from the boot image address. Grab the magic number from there
and allow U-Boot to handle LZ4-compressed KNL binaries instead of
hardcoding compression type to IH_COMP_NONE. Other compression types,
if needed, can be added later.
Tested on H3ULCB-KF using the image detailed in [2].
[1] Excerpt from include/android_image.h
+-----------------+
| boot header | 1 page
+-----------------+
| kernel | n pages
+-----------------+
| ramdisk | m pages
+-----------------+
| second stage | o pages
+-----------------+
projects / u-boot.git / log