Frieder Schrempf [Mon, 27 Jun 2022 11:00:58 +0000 (13:00 +0200)]
pmic: pca9450: Add optional SD_VSEL GPIO for LDO5
LDO5 has two separate control registers. LDO5CTRL_L is used if the
input signal SD_VSEL is low and LDO5CTRL_H if it is high.
The current driver implementation only uses LDO5CTRL_H. To make this
work on boards that have SD_VSEL connected to a GPIO, we add support
for specifying an optional GPIO and setting it to high at probe time.
In the future we might also want to add support for boards that have
SD_VSEL set to a fixed low level. In this case we need to change the
driver to be able to use the LDO5CTRL_L register.
This is a port of the same change in the Linux kernel: 8c67a11bae88 ("regulator: pca9450: Add SD_VSEL GPIO for LDO5")
In case rtt_nom is set to 0 keep ODT disabled (MMDC MPODTCTRL = 0).
No changes required for DDR MR1 Rtt_Nom impedance register, 0 value is
already handled correctly.
No board is currently affected by this change (rtt_nom != 0 on all i.MX6
ddr3 boards), this will be used by a follow-up change.
Fixes: fe0f7f7842e1 ("mx6: add mmdc configuration for MX6Q/MX6DL") Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Fabio Estevam <festevam@denx.de> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Set CLK01 and CLK02 to 24MHz and enable it in CCM_CCOSR register.
This clock is used by both the audio codec (CLKO1) and by the CSI camera
(CLKO2) and is expected to be 24MHz.
Despite the wrong 16.5MHz there was no real issue because of the wrong
frequency since Linux reconfigures the clocks afterward, however this
was triggering an issue with noise coming from the SGTL5000 audio codec.
The problem is that the SGTL5000 does not have a reset pin and after it
is configured if the input MCLK clock is disabled it produces a constant
noise on its output, this was happening on software reboot.
Forcing the clock to be enabled in U-Boot prevent the problem by making
sure that the clock is always available, without this change as soon as
Linux was changing the clock tree (setting clk_out_sel=1 without setting
clko2_en=1) the noise would start till the actual clock was enabled
(clko2_en=1) during the SGTL5000 driver probe.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Fabio Estevam <festevam@denx.de>
Fixup thermal trips in Linux device tree according to SoC thermal
grade.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com> Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Tested-by: Adam Ford <aford173@gmail.com>
Tom Rini [Mon, 27 Jun 2022 01:06:08 +0000 (21:06 -0400)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
The main attraction are two regressions, plus a fix
for a long standing bug:
- Fix USB support on boards with a switched VBUS regulator.
- Fix failing boot due to env loading on boards without MMC (CHIP).
- Fix PSCI CPU_OFF operation on R40 boards.
The rest are smaller fixes, and the forgotten DT sync for sun4i boards.
qianfan Zhao [Sat, 14 May 2022 03:19:23 +0000 (11:19 +0800)]
sunxi: psci: Fix sunxi_power_switch on sun8i-r40 platform
linux system will die if we offline one of the cpu on R40 based board:
eg: echo 0 > /sys/devices/system/cpu/cpu3/online
The reason is that the R40 version of sunxi_cpu_set_power always passes
0 for the CPU number, so we turn off CPU0, regardless of what CPU the
CPU_OFF request came for.
Fix this by passing the proper CPU number, as there are proper power
clamp registers for every of the four cores.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Wed, 20 Apr 2022 22:15:39 +0000 (23:15 +0100)]
sunxi: fix initial environment loading without MMC
Commit e42dad4168fe ("sunxi: use boot source for determining environment
location") changed our implementation of env_get_location() and enabled
it for every board, even those without MMC support (like the C.H.I.P.
boards). However the default fallback location of ENVL_FAT requires MMC
support compiled in, so the board hangs when trying to initially load
the environment.
Change the algorithm to only return configured environment locations,
and improve the fallback algorithm on the way.
The env_init() routine calling this function here does not behave well
if the return value is ENVL_UNKNOWN on the very first call: it will make
U-Boot proper silently hang very early.
Work around this issue by making sure we return some configured (dummy)
environment location when prio is 0. This for instance happens when
booting via FEL.
This fixes U-Boot loading on the C.H.I.P. boards.
Fixes: e42dad4168fe ("sunxi: use boot source for determining environment location") Reported-by: Chris Morgan <macroalpha82@gmail.com> Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fix FEL boot case by not returning ENVL_UNKNOWN when prio==0] Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sun, 1 May 2022 03:38:36 +0000 (22:38 -0500)]
clk: sunxi: Add additional RTC compatible strings
Compatible strings for some new RTC hardware variants were added to
the binding. Add them to the driver in preparation for supporting
those new SoCs.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Wed, 11 May 2022 00:03:34 +0000 (19:03 -0500)]
gpio: sunxi: Fix build with CONFIG_SPL_SERIAL=n
This driver uses simple_strtol(), so it needs SPL_STRTO. Before commit 88ca8e26958b6 ("disk: Add an option for partitions in SPL"), SPL_STRTO
was always selected indirectly. Now it is not, so select it here.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Thu, 26 May 2022 03:26:02 +0000 (22:26 -0500)]
ARM: dts: sun4i: Sync from Linux v5.18-rc1
Copy the devicetree source for the A10 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
The previous version of this change was only partially applied.
Fixes: 4746694cba74 ("ARM: dts: sun4i: Sync from Linux v5.18-rc1") Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Tue, 7 Jun 2022 22:36:18 +0000 (23:36 +0100)]
sunxi: usb: convert PHY GPIO functions to DM
The Allwinner USB PHY driver is still using the legacy GPIO interface,
which is now implemented by the DM_GPIO compat functions.
Those seem to have some design flaws, as setting the direction, then
later setting the value will not work, if the DM_GPIO driver is
implementing set_flags.
Fix this by using the dm_ version of the direct GPIO interface, which
uses struct gpio_desc structs to handle requested GPIOs, and actually
keeps the flags we set earlier.
This fixes USB operation on boards which need to toggle the VBUS supply
via a GPIO, like the Teres-I laptop or the BananaPi M2 Berry board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reported-by: Milan P. Stanić <mps@arvanta.net> Reviewed-by: Samuel Holland <samuel@sholland.org>
Tom Rini [Sat, 25 Jun 2022 12:38:00 +0000 (08:38 -0400)]
Merge tag 'video-20220625' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix building sandbox with NO_SDL=1
- fix stb TrueType to check return value of STBTT_malloc()
- remove not required DM_REGULATOR test in stm32 dsi driver
Patrick Delaunay [Mon, 20 Jun 2022 09:55:07 +0000 (11:55 +0200)]
video: stm32: remove test on CONFIG_DM_REGULATOR
The tests on CONFIG_DM_REGULATOR, added to avoid compilation issues, can
now be removed, they are no more needed since the commit 16cc5ad0b439
("power: regulator: add dummy helper").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Building the sandbox with NO_SDL=1 resulted in an undefined reference to
'sandbox_sdl_remove_display'. Resolve this by adding a stub
implementation to match the stubs of the other similar functions.
Signed-off-by: Andrew Scull <ascull@google.com> Cc: Simon Glass <sjg@chromium.org> Cc: Anatolij Gustschin <agust@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Janne Grunau [Tue, 14 Jun 2022 07:09:09 +0000 (09:09 +0200)]
arm: apple: Increase RTKit timeouts
Timeouts are not expected to happen and are handled as fatal errors.
Increase all timeouts to 1 second as defensive measure to avoid relying
on the timing behaviour of certain firmware versions or configurations.
Signed-off-by: Janne Grunau <j@jannau.net> Reviewed-by: Mark Kettenis <kettenis@openbsd.org> Tested-by: Mark Kettenis <kettenis@openbsd.org>
Janne Grunau [Tue, 14 Jun 2022 07:09:07 +0000 (09:09 +0200)]
arm: apple: nvme: Add SART support and RTKit buffer management
The NVMe firmware in the macOS 13 beta blocks or crashes with u-boot's
current minimal RTKit implementation. It does not provide buffers for
the firmware's buffer requests. The ANS2 firmware included in macOS 11
and 12 tolerates this. The firmware included in the first macOS 13 beta
requires buffers for the crashlog and ioreport endpoints to function.
In the case of the NVMe the buffers are physical memory. Access to
physical memory is guarded by what Apple calls SART.
Import m1n1's SART driver (exclusively used for the NVMe controller).
Implement buffer management helpers for RTKit. These are generic since
other devices (none in u-boot so far) require different handling.
Signed-off-by: Janne Grunau <j@jannau.net> Reviewed-by: Mark Kettenis <kettenis@openbsd.org> Tested-by: Mark Kettenis <kettenis@openbsd.org>
If CONFIG_VIDEO_DM=n we query the display size from the serial console.
Especially when using a remote console the response can be so late that
it interferes with autoboot.
Only query the console size when running an EFI binary.
Add debug output showing the determined console size.
Reported-by: Fabio Estevam <festevam@gmail.com> Fixes: a57ad20d07e8 ("efi_loader: split efi_init_obj_list() into two stages") Fixes: a9bf024b2933 ("efi_loader: disk: a helper function to create efi_disk objects from udevice") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Tested-by: Fabio Estevam <festevam@denx.de> Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
When the UEFI sub-system is initialized it sends an escape sequence to the
serial console to determine the terminal size. This stops the
run_command_list() function of the console emulation from recognizing the
U-Boot command line prompt.
Add a 'print -e' command as first command in the command list to work
around this issue.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Dinesh Maniyam [Wed, 1 Jun 2022 07:57:25 +0000 (15:57 +0800)]
drivers: cache: ncore: Disable snoop filter
There is hardware bug in NCORE CCU IP and it is causing an issue in the
coherent directory tracking of outstanding cache lines.
The workaround is disabling snoop filter.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com> Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Dinesh Maniyam [Wed, 1 Jun 2022 07:54:59 +0000 (15:54 +0800)]
arch: arm: socfpga: timer_s10: Override udelay for secure section
Override __udelay() as 'always inlined' function so that PSCI code
run in '__secure' section can call this delay function as well.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com> Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com> Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Marek Vasut [Mon, 13 Jun 2022 09:55:21 +0000 (11:55 +0200)]
ARM: dts: stm32: Add DHCOR based DRC Compact board
Add DT for DH DRC Compact unit, which is a universal controller device.
The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
card slot, eMMC and SDIO Wi-Fi.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrick Delaunay [Thu, 16 Jun 2022 16:37:59 +0000 (18:37 +0200)]
stm32mp: stm32prog: fix the last character of dfu_alt_add third parameter
The third parameter of dfu_alt_add(), the string description of alternate,
is build in stm32prog_alt_add() with a unnecessary character ';' at the
end of the string.
This separator was required in the first implementation of
dfu_alt_add() but is no more needed in the current implementation;
this separator is managed only in dfu_config_interfaces() which call
dfu_alt_add() for this parameter without this separator.
And since the commit 53b406369e9d ("DFU: Check the number of arguments
and argument string strictly"), this added character cause an error when
the stm32prog command is executed because the third parameter of
dfu_alt_add() must be a string with a numerical value; 's' must be NULL
in the result of call in dfu_fill_entity_mmc():
third_arg = simple_strtoul(argv[2], &s, 0);
Fixes: 53b406369e9d ("DFU: Check the number of arguments and argument string strictly") Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Marek Vasut [Sun, 1 May 2022 16:43:55 +0000 (18:43 +0200)]
net: Fix discuss discard typo
Replace discuss with discard, that is what happens with packet with
incorrect checksum. Fix the typo.
Fixes: 4b37fd146bb ("Convert CONFIG_UDP_CHECKSUM to Kconfig") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Ramon Fried <rfried.dev@gmail.com> Cc: Simon Glass <sjg@chromium.org>
Corentin LABBE [Tue, 14 Jun 2022 08:44:07 +0000 (08:44 +0000)]
board: ti: am335x: eth_cpsw should depend on CONFIG_NET
The origin of this patch is the breaking of am335x-hs boot
due to commit e41651fffda7 ("dm: Support parent devices with of-platdata")
HS boards have less SRAM for SPL and so this commit increased memory usage beyond am335x limit.
This commit added 10 driver binding pass and am335x boot only if one pass is done.
SPL try to do more than one pass due to eth_cpsw failing.
Since HS SPL does not need network (and NET is already disabled in config),
the easiest fix is to "remove" eth_cpsw from SPL by testing if NET is enabled.
Signed-off-by: Corentin LABBE <clabbe@baylibre.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Andrew Davis <afd@ti.com>
Andre Przywara [Mon, 13 Jun 2022 23:11:10 +0000 (00:11 +0100)]
armv8: always use current exception level for TCR_ELx access
Currently get_tcr() takes an "el" parameter, to select the proper
version of the TCR_ELx system register.
This is problematic in case of the Apple M1, since it runs with
HCR_EL2.E2H fixed to 1, so TCR_EL2 is actually using the TCR_EL1 layout,
and we get the wrong version.
For U-Boot's purposes the only sensible choice here is the current
exception level, and indeed most callers treat it like that, so let's
remove that parameter and read the current EL inside the function.
This allows us to check for the E2H bit, and pretend it's EL1 in this
case.
There are two callers which don't care about the EL, and they pass 0,
which looks wrong, but is irrelevant in these two cases, since we don't
use the return value there. So the change cannot affect those two.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Mark Kettenis <kettenis@openbsd.org> Tested-by: Mark Kettenis <kettenis@openbsd.org>
With the move to use DM_CLK the boards uart stops working. The used
properties are not supported by the imx8mq clock driver. Thus
the correct baudrate cannot be selected. Remove this properties here and
the board can start with working uart. Keep it in the main dts because
linux handles these porperties fine.
Andre Przywara [Tue, 7 Jun 2022 23:42:22 +0000 (00:42 +0100)]
usb: host: ehci-generic: Make resets and clocks optional
The generic EHCI binding does not *require* resets and clocks
properties, and indeed for instance the Allwinner A20 SoCs does not
need or define any resets in its DT.
Don't easily give up if clk_get_bulk() or reset_get_bulk() return an
error, but check if that is due to the DT simply having no entries for
either of them.
This fixes USB operation on all boards with an Allwinner A10 or A20 SoC,
which were reporting an error after commit ba96176ab70e2999:
=======================
Bus usb@1c14000: ehci_generic usb@1c14000: Failed to get resets (err=-2)
probe failed, error -2
=======================
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Following Jincheng's report, an out-of-band write leading to arbitrary
code execution is possible because on one side the squashfs logic
accepts directory names up to 65535 bytes (u16), while U-Boot fs logic
accepts directory names up to 255 bytes long.
Prevent such an exploit from happening by capping directory name sizes
to 255. Use a define for this purpose so that developers can link the
limitation to its source and eventually kill it some day by dynamically
allocating this array (if ever desired).
Tom Rini [Wed, 8 Jun 2022 18:30:14 +0000 (14:30 -0400)]
odroid_xu3: Fix board environment variable
When migrating CONFIG_CONS_INDEX to Kconfig, on this platform we changed
what "board" evaluated to in the environment. This in turn meant that
we would no longer try and find the correct fdtfile via the normal
distro boot logic. Fix this by overriding board in the default
environment, as done on other platforms where CONFIG_SYS_BOARD is not
what we want to be in the board environment variable.
Fixes: f76750d11133 ("Convert CONFIG_CONS_INDEX et al to Kconfig") Reported-by: Gabriel Hojda <ghojda@yo2urs.ro> Tested-by: Gabriel Hojda <ghojda@yo2urs.ro> Signed-off-by: Tom Rini <trini@konsulko.com>
b4 utility [1] is introduced by Linux Kernel developers and used to
fetch patches and patch series from lore.kernel.org and is proven
to be useful for U-Boot development. Detailed usage of the tool can be
read under post from the original author [2].
This tool fetches files from the list and populates the source folder
with additional files (*.cover and *.mbx) which are not ignored by git
and shown as newly added files.
Add those file patterns into .gitignore file, so they can be safely
skipped during changes attestation.
Stefan Roese [Fri, 29 Apr 2022 13:34:44 +0000 (15:34 +0200)]
crypto: fsl_hash: Remove unnecessary alignment check in caam_hash()
While working on an LX2160 based board and updating to latest mainline
I noticed problems using the HW accelerated hash functions on this
platform, when trying to boot a FIT Kernel image. Here the resulting
error message:
Using 'conf-freescale_lx2160a.dtb' configuration
Trying 'kernel-1' kernel subimage
Verifying Hash Integrity ... sha256Error: Address arguments are not aligned
CAAM was not setup properly or it is faulty
error!
Bad hash value for 'hash-1' hash node in 'kernel-1' image node
Bad Data Hash
ERROR: can't get kernel image!
Testing and checking with Gaurav Jain from NXP has revealed, that this
alignment check is not necessary here at all. So let's remove this
check completely.
Marek Vasut [Mon, 20 Dec 2021 21:57:57 +0000 (22:57 +0100)]
arm: socfpga: vining: Unmount UBIFS and detach UBI in ubi_load script
Clean up in ubiload script. Unmount UBIFS from which kernel image was
loaded and detach UBI on which the UBIFS is located, otherwise message
similar to the following is printed just before booting kernel:
Removing MTD device #7 (rootfs) with use count 1
Error when deleting partition "rootfs" (-16)
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
ddr: altera: Stratix10: Use phys_size_t for memory size
Replace with phys_size_t for all memory size variables declaration
for the sake of scalability. phys_size_t is defined in
/arch/arm/include/asm/types.h.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
ddr: altera: Ignore bit[7-4] for both seq2core & core2seq handshake in HPS
Bit[7-4] for both register seq2core and core2seq handshake in HPS are not
required for triggering DDR re-calibration or resetting EMIF. So, ignoring
these bits just for playing it safe.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Tien Fong Chee [Fri, 10 Jun 2022 11:18:00 +0000 (19:18 +0800)]
intel: n5x: ddr: update license
All the source code of sdram_n5x.c are from Intel, update the license to
use both GPL2.0 and BSD-3 Clause because this copy of code may used for
open source and internal project.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Marek Vasut [Mon, 13 Jun 2022 12:35:25 +0000 (14:35 +0200)]
spi: nxp_fspi: Fix clock imbalance
The nxp_fspi_default_setup() is only ever called from nxp_fspi_probe(),
where the IP clock are initially disabled. Drop the second disabling of
clock to prevent clock enable/disable imbalance reported by clock core:
"
clk qspi_root_clk already disabled
"
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Loic Poulain [Thu, 26 May 2022 14:37:21 +0000 (16:37 +0200)]
mmc: Add support for wait_dat0 callback
There is no wait_dat0 mmc ops, causing operations waiting for data
line state change (e.g mmc_switch_voltage) to fallback to a 250ms
active delay. mmc_ops still used when DM_MMC is not enabled, which
is often the case for SPL. The result can be unexpectly long SPL
boot time.
This change adds support for wait_dat0() mmc operation.
Patrick Delaunay [Tue, 15 Feb 2022 15:23:23 +0000 (16:23 +0100)]
env: mmc : align erase address and size on erase_grp_size
On eMMC device, the erase_grp_size > 1 so the address and size for the
erase block command in env/mmc.c can be unaligned on erase group size and
some strange trace occurs and the result is not guarantee by MMC devices.
The SD-Card behavior doesn't change as erase_grp_size = 1 for SD-Card.
For example, on eMMC present on STM32MP15C-EV1 and before the patch:
STM32MP> env erase
Erasing Environment on MMC...
Caution! Your devices Erase group is 0x400
The erase range would be change to 0x2000~0x27ff
16 blocks erased: OK
Caution! Your devices Erase group is 0x400
The erase range would be change to 0x2000~0x23ff
16 blocks erased: OK
OK
After this patch:
STM32MP> env erase
Erasing Environment on MMC...
1024 blocks erased at 0x2000: OK
1024 blocks erased at 0x2000: OK
OK
Here the 2 copies of U-Boot environment are in the same devices Erase
group: it is erased twice.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Upstream commit 7a2c3be95a50 ("clk: imx8mp: Fill in DWC3 USB, USB PHY,
HSIOMIX clock") added usb_core_ref for USB Controller but never set it
to be used as a clock source, using rather "osc_32k" instead.
This produces following boot log message:
"clk_register: failed to get osc_32k device (parent of usb_root_clk)"
Fix the USB controller clock source by using usb_core_ref instead of
osc_32k.
Fixes: 7a2c3be95a50 ("clk: imx8mp: Fill in DWC3 USB, USB PHY, HSIOMIX clock") Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Cc: Fabio Estevam <festevam@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <festevam@denx.de>
systemd prints its messages on the last console= statement that it finds
in the kernel arguments. The current ordering sends the systemd messages
to tty1, by default this is the display.
Ensure that systemd sends its messages to the default UART, reorder the
console= statements accordingly.
Josua Mayer [Thu, 19 May 2022 09:31:59 +0000 (12:31 +0300)]
mx6cuboxi: fixup dtb ethernet phy nodes before booting an OS
SoM revision 1.9 has replaced the ar8035 phy address 0 with an adin1300
at address 1. Because early SoMs had a hardware flaw, the ar8035 can
also appear at address 4 - making it a total of 3 phy nodes in the DTB.
To avoid confusing Linux with probe errors, fixup the dtb to only enable
the phy node that is detected at runtime.
Josua Mayer [Thu, 19 May 2022 09:31:58 +0000 (12:31 +0300)]
ARM: dts: imx6qdl-sr-som: add support for alternate phy addresses
The Cubox has an unstable phy address - which can appear at either
address 0 (intended) or 4 (unintended).
SoM revision 1.9 has replaced the ar8035 phy with an adin1300, which
will always appear at address 1.
Change the reg property of the phy node to the magic value 0xffffffff,
which indicates to the generic phy driver that all addresses should be
probed. That allows the same node (which is pinned by phy-handle) to match
either the AR8035 PHY at both possible addresses, as well as the new one
at address 1.
Also add the new adi,phy-output-clock property for enabling the 125MHz
clock used by the fec ethernet controller, as submitted to Linux [1].
Linux solves this problem differently:
For the ar8035 phy it will probe both phy nodes in device-tree in order,
and use the one that succeeds. For the new adin1300 it expects U-Boot to
patch the status field in the DTB before booting
While at it also sync the reset-delay with the upstream Linux dtb.
Nate Drude [Thu, 19 May 2022 09:31:56 +0000 (12:31 +0300)]
phy: adin: fix broken support for adi, phy-mode-override
Currently, the adin driver fails to compile.
The original patch introducing the adin driver used the function
phy_get_interface_by_name to support the adi,phy-mode-override
property. Unfortunately, a few days before the adin patch
was accepted, another patch removed support for phy_get_interface_by_name:
Tom Rini [Tue, 14 Jun 2022 17:59:23 +0000 (13:59 -0400)]
dtoc: Update test_src_scan.py for new tegra compatibles
This test was written to match up with the list of compatibles in
drivers/i2c/tegra_i2c.c so adding another one requires the test to be
updated to match.
Fixes: 0d2105ae5e32 ("arm: tegra: Update some DT compatibles") Signed-off-by: Tom Rini <trini@konsulko.com>
The pca9450 driver uses dm_i2c_{read,write}, which
are (unsurprisingly) only available with DM_I2C. Make sure one can't
create an unbuildable .config by adding proper dependencies.
While here, append "in SPL" to the prompt for the SPL_ variant so it
doesn't read the same as the one for the non-SPL_ variant.
Tom Rini [Mon, 13 Jun 2022 13:33:37 +0000 (09:33 -0400)]
Merge tag 'efi-2022-07-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc5
UEFI:
* Ignore OsIndications if CONFIG_EFI_IGNORE_OSINDICATIONS=y
* Correct UEFI default binary name
* Let efidebug create boot options without file path
* Support booting with a boot option with shortened device only device path
Sughosh Ganu [Wed, 1 Jun 2022 18:00:41 +0000 (23:30 +0530)]
EFI: FMP: Use a common GetImageInfo function for FIT and raw images
The GetImageInfo function definitions for the FIT images and raw
images are the same. Use a common function for the both the Firmware
Management Protocol(FMP) instances for raw and FIT images.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Sughosh Ganu [Wed, 1 Jun 2022 18:00:39 +0000 (23:30 +0530)]
EFI: Do not consider OsIndications variable if CONFIG_EFI_IGNORE_OSINDICATIONS is enabled
The EFI_IGNORE_OSINDICATIONS config symbol was introduced as a
mechanism to have capsule updates work even on platforms where the
SetVariable runtime service was not supported. The current logic
requires the OsIndications variable to have been set to a 64 bit value
even when the EFI_IGNORE_OSINDICATIONS config is enabled. Return an
error code on not being able to read the variable only when
EFI_IGNORE_OSINDICATIONS is not enabled.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Marek Vasut [Sun, 10 Apr 2022 04:27:14 +0000 (06:27 +0200)]
misc: Port USB251xB/xBi Hi-Speed Hub Controller Driver from Linux
This patch adds a driver for configuration of the Microchip USB251xB/xBi
USB 2.0 hub controller series with USB 2.0 upstream connectivity, SMBus
configuration interface and two to four USB 2.0 downstream ports.
This is ported from Linux as of Linux kernel commit 5c2b9c61ae5d8 ("usb: usb251xb: add boost-up property support")
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Simon Glass <sjg@chromium.org>
Chunfeng Yun [Fri, 27 May 2022 01:52:09 +0000 (09:52 +0800)]
usb: xhci-mtk: disable all ports when disable host controller
This is used to avoid the ports status of IPPC being brought in kernel
stage, it may cause ports error especially when the xhci controller is
a component of dual-role controller.
projects / u-boot.git / log