Peter Hoyes [Thu, 11 Nov 2021 09:26:02 +0000 (09:26 +0000)]
vexpress64: Enable OF_CONTROL and OF_BOARD for VExpress64
Capture x0 in lowlevel_init.S as potential fdt address. Modify
board_fdt_blob_setup to use fdt address from either vexpress_aemv8.h
or lowlevel_init.S.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Simon Glass [Wed, 29 Dec 2021 18:57:53 +0000 (11:57 -0700)]
x86: efi: Show the system-table revision
Show the revision of this table as it can be important.
Also update the 'efi table' entry to show the actual address of the EFI
table rather than our table that points to it. This saves a step and the
intermediate table has nothing else in it.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Simon Glass [Wed, 29 Dec 2021 18:57:48 +0000 (11:57 -0700)]
efi: Mention that efi_info_get() is only used in the stub
This provides access to EFI tables after U-Boot has exited boot services.
It is not needed in the app since boot services remain alive and we can
just call them whenever needed.
Add a comment to explain this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Simon Glass [Wed, 29 Dec 2021 18:57:40 +0000 (11:57 -0700)]
x86: efi: Add room for the binman definition in the dtb
At present only 4KB of spare space is left in the DTB when building the
EFI app. Increase this to 32KB so there is plenty of space to insert the
binman definition. This cannot be expanded later (as with OF_SEPARATE)
because the ELF image has already been built.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviwed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Simon Glass [Wed, 29 Dec 2021 18:57:37 +0000 (11:57 -0700)]
efi: serial: Support arrow keys
At present only the backspace key is supported in U-Boot, when running as
an EFI app. Add support for arrows, home and end as well, to make the CLI
more friendly.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Simon Glass [Wed, 29 Dec 2021 18:57:36 +0000 (11:57 -0700)]
efi: Locate all block devices in the app
When starting the app, locate all block devices and make them available
to U-Boot. This allows listing partitions and accessing files in
filesystems.
EFI also has the concept of 'disks', meaning boot media. For now, this
is not obviously useful in U-Boot, but add code to at least locate these.
This can be expanded later as needed.
We cannot use printf() in the early stub or app since it is not compiled
in
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Andre Przywara [Mon, 27 Dec 2021 15:07:36 +0000 (15:07 +0000)]
sunxi: add board documentation
Add some long overdue instructions for building and installing U-Boot on
Allwinner SoC based boards.
This describes the building process, including TF-A and crust, plus
installation to SD card, eMMC and SPI flash, both from Linux and U-Boot
itself. Also describe FEL booting.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Ilias Apalodimas [Fri, 24 Dec 2021 08:08:41 +0000 (10:08 +0200)]
efi_loader: Don't limit the StMM buffer size explicitly
Currently we allow and explicitly check a single shared page with
StandAloneMM. This is dictated by OP-TEE which runs the application.
However there's no way for us dynamically discover the number of pages we
are allowed to use. Since writing big EFI signature list variable
requires more than a page, OP-TEE has bumped the number of shared pages to
four.
Let's remove our explicit check and allow the request to reach OP-TEE even
if it's bigger than what it supports. There's no need to sanitize the
number of pages internally. OP-TEE will fail if we try to write more
than it's allowed. The error will just trigger later on, during the
StMM access.
While at it add an error message to help users figure out what failed.
Tom Rini [Tue, 28 Dec 2021 16:28:31 +0000 (11:28 -0500)]
Merge tag 'video-next-20211228' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
Tom Rini [Mon, 27 Dec 2021 22:20:21 +0000 (17:20 -0500)]
Merge branch '2021-12-27-CONFIG-migrations' into next
- Merge a large number of CONFIG migration patches. Most of these are
taking existing migrations and re-running them. A few of these needed
additional minor conversions done first, so that more complex
dependencies could be expressed. In the end we now have CI jobs to
ensure that no migrated symbols are used in board config header files.
Tom Rini [Fri, 17 Dec 2021 23:08:39 +0000 (18:08 -0500)]
serial: arm_dcc: Use CONFIG_ARM64 not CONFIG_CPU_ARMV8
The only place we use CONFIG_CPU_ARMV8 was in the arm_dcc serial driver.
Switch this to CONFIG_ARM64 today, and if in the future we need finer
granularity tuning here, a new CONFIG_SERIAL option needs to be
introduced.
Tom Rini [Tue, 14 Dec 2021 18:36:41 +0000 (13:36 -0500)]
CI: Test for unmigrated CONFIG symbols in board config.h files
Now that all symbols that exist in Kconfig no longer also have boards
setting them in the board config.h file, add a CI test to catch new
instances of this, and fail.
Tom Rini [Tue, 14 Dec 2021 18:36:40 +0000 (13:36 -0500)]
Finish conversion of CONFIG_SYS_CLK_FREQ to Kconfig
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Tom Rini [Tue, 14 Dec 2021 18:36:39 +0000 (13:36 -0500)]
CONFIG_SYS_CLK_FREQ: Consistently be static or get_board_sys_clk()
This CONFIG option is used in one of two ways. The first way is that it
is defined to a static value, of an unsigned long size. The second way
is that it is defined to something, typically a function, to determine
this value at run time.
However, in a few cases that function returns a static value. Change
that to using the static value directly.
In the case of using something at run time, convert everything to using
a function of the same name and prototype. This will allow for further
cleanups.
Finally, we have a few cases where the function is just not used, so
drop it.
Tom Rini [Tue, 14 Dec 2021 18:36:38 +0000 (13:36 -0500)]
nxp: ics307_clk: Guard get_board_ddr_clk function correctly
When we have CONFIG_DYNAMIC_DDR_CLK_FREQ set is the only time we should
have this function, so guard it so that we can include <clock_legacy.h>
in this file later on.
Tom Rini [Tue, 14 Dec 2021 18:36:37 +0000 (13:36 -0500)]
ls1088a: Guard get_board_ddr_clk function correctly
When we have CONFIG_DYNAMIC_DDR_CLK_FREQ set is the only time we should
have this function, so guard it so that we can include <clock_legacy.h>
in this file later on.
Tom Rini [Tue, 14 Dec 2021 18:36:36 +0000 (13:36 -0500)]
arm: s5pc1xx: Move CONFIG_SYS_CLK_FREQ_C1x0 out of CONFIG namespace
The values CONFIG_SYS_CLK_FREQ_C100 and CONFIG_SYS_CLK_FREQ_C110 are
only used in one place and not changed by the board config file. Move
these out of the CONFIG namespace and in to the CFG namespace.
Tom Rini [Mon, 13 Dec 2021 03:12:36 +0000 (22:12 -0500)]
Finish conversion CONFIG_SYS_NAND_SELF_INIT to Kconfig
In order to finish this conversion we need to add a symbols for
SPL_SYS_NAND_SELF_INIT and TPL_SYS_NAND_SELF_INIT as there are cases
there where we need to, or need to not, use that framework as things
stand.
Tom Rini [Mon, 13 Dec 2021 03:12:34 +0000 (22:12 -0500)]
Finish converting CONFIG_SYS_FSL_CLK to Kconfig
This converts the following to Kconfig:
CONFIG_SYS_FSL_CLK
We move the exiting option to common/Kconfig near the other options to
control the contents of board_init_f() and note that this is a legacy
option. We further restrict this to where the call is going to be
non-empty, for the SoCs that had only been using this for some
MMC-related clocks.
Tom Rini [Mon, 13 Dec 2021 03:12:33 +0000 (22:12 -0500)]
warp7, pic32mzdask: Remove SYS_FDT_ADDR/SYS_ENV_ADDR from CONFIG namespace
In the case of CONFIG_SYS_FDT_ADDR this was being used to modify the
default value of fdt_addr / fdt_addr_r, which is not something to expose
in this manner and is not otherwise done. The case of SYS_ENV_ADDR is
similar but only done on the pic32mzdask platform, for scriptaddr.
Tom Rini [Mon, 13 Dec 2021 03:12:31 +0000 (22:12 -0500)]
Finish CONFIG_VID et al conversion to Kconfig
This converts the following to Kconfig:
CONFIG_VID
CONFIG_VOL_MONITOR_INA220
CONFIG_VOL_MONITOR_IR36021_READ
CONFIG_VOL_MONITOR_IR36021_SET
CONFIG_VOL_MONITOR_LTC3882_READ
CONFIG_VOL_MONITOR_LTC3882_SET
To finish this migration, we first need to introduce CONFIG_SPL_VID as
some platforms only use this code in full U-Boot while others use it in
SPL as well. To make the Kconfig logic clearer, guard all of the
sub-options with a if VID || SPL_VID check. Finally, add Kconfig
options for the remaining related options that did not previously have
one.
Tom Rini [Mon, 13 Dec 2021 03:12:30 +0000 (22:12 -0500)]
Convert CONFIG_SYS_IMMR to Kconfig
This converts the following to Kconfig:
CONFIG_SYS_IMMR
We do this by consolidating the SYS_IMMR options we have and providing
defaults.
We also, in the few places where M68K was also sharing code with these
platforms, define it within the file to CONFIG_SYS_MBAR to match usage.
This should be cleaned up longer term.
Tom Rini [Mon, 13 Dec 2021 03:12:27 +0000 (22:12 -0500)]
Finish converting CONFIG_WATCHDOG, HW_WATCHDOG and WDT to Kconfig
Because of how these symbols work, and the remaining board config.h file
uses, we need to do these at the same time. In some cases we just get
to move rather directly to the defconfigs. A few cases require manual
intervention.
For the case of the eb_cpu5282 we need to select HW_WATCHDOG for the
target, given how it's implemented.
For the cases of m53menlo, dh_imx6, display5, and display5_factory we
disable SPL watchdog support as the particular combination of options
they want would require either more symbols or enabling SPL_DM.
Tom Rini [Sat, 11 Dec 2021 19:55:52 +0000 (14:55 -0500)]
Remove CONFIG_SYS_MMC_IMG_LOAD_PART from CONFIG namespace
This option is used as part of configuring the default environment for a
number of platforms. However, it is always set to 1 and the only time
it is part of Kconfig, it is used in a hard-coded manner. Hard-code the
value in the environment instead.
Tom Rini [Sat, 11 Dec 2021 19:55:48 +0000 (14:55 -0500)]
Convert CONFIG_ENV_SPI_BUS et al to Kconfig
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Tom Rini [Sat, 11 Dec 2021 19:55:47 +0000 (14:55 -0500)]
Clarify CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW in Kconfig
This is a "hex" prompt but the default value was given as an int.
Switch the default to hex (0x0) and remove the defconfigs that were
using the default, but as hex before.
Simon Glass [Fri, 19 Nov 2021 20:24:02 +0000 (13:24 -0700)]
video: Drop VIDEO_LOGO from cfb_console
This driver is obsolete and only used by nokia_rx51. It should be deleted.
For now, drop the VIDEO_LOGO code to avoid confusion with the new
implementation.
Simon Glass [Fri, 19 Nov 2021 20:23:59 +0000 (13:23 -0700)]
video: theadorable: Use RGB565 for BMP blitting
At present this uses RGB555 format for blitting to a display. Sandbox uses
565 and that seems to be more normal for BMP as well. Update the code
accordingly and add a test.
Note that this likely breaks the theadorable board so we may need to
discuss supporting both formats.
Simon Glass [Fri, 19 Nov 2021 20:23:54 +0000 (13:23 -0700)]
video: Move BMP pixel-writing into a function
At present the code that writes to a pixel is quite convoluted. It uses a
colour map which is in the uclass and the same code is repeated in
different places within video_bmp_display().
As a first step, create a function which can write a pixel from the
bitmap, no matter what the display depth. Use any provided palette
directly, rather than using the uclass version.
Simon Glass [Fri, 19 Nov 2021 20:23:49 +0000 (13:23 -0700)]
sandbox: video: Correct the address of the copy base
The intention is for the copy base to start halfway through the
frame-buffer area. At present is it actually below the frame buffer,
which could have anything in it (probably it is malloc space). Fix
this.
Simon Glass [Fri, 19 Nov 2021 20:23:48 +0000 (13:23 -0700)]
video: sandbox: Set a maximum frame-buffer size
If U-Boot starts with the frame buffer set to 16bpp but then runs a test
that uses 32bpp, there is not enough space. Update the driver to use the
maximum possible frame-buffer size, to avoid this.
Simon Glass [Fri, 19 Nov 2021 20:23:47 +0000 (13:23 -0700)]
console: Avoid serial output before the console is running
The video driver uses this for debugging, but if used before relocation it
crashes at present. Avoid trying to output debugging before the console is
ready.
Simon Glass [Fri, 19 Nov 2021 20:23:46 +0000 (13:23 -0700)]
video: sandbox: Avoid duplicate display windows
When unit tests are run they currently create a new window. Update the
code so that the old one is removed first. This avoids the confusion as to
which one is active.
Tom Rini [Fri, 24 Dec 2021 14:31:35 +0000 (09:31 -0500)]
Merge branch '2021-12-23-make-OF_BOARD-a-boolean' into next
Merge v8 of Simon's series to make CONFIG_OF_BOARD a boolean option.
Quoting him:
With Ilias' efforts we have dropped OF_PRIOR_STAGE and OF_HOSTFILE so
there are only three ways to obtain a devicetree:
- OF_SEPARATE - the normal way, where the devicetree is built and
appended to U-Boot
- OF_EMBED - for development purposes, the devicetree is embedded in
the ELF file (also used for EFI)
- OF_BOARD - the board figures it out on its own
The last one is currently set up so that no devicetree is needed at all
in the U-Boot tree. Most boards do provide one, but some don't. Some
don't even provide instructions on how to boot on the board.
The problems with this approach were covered in another patch[1], since
removed from this series.
In practice, OF_BOARD is not really distinct from OF_SEPARATE. Any board
can obtain its devicetree at runtime, even it is has a devicetree built
in U-Boot. This is because U-Boot may be a second-stage bootloader and its
caller may have a better idea about the hardware available in the machine.
This is the case with a few QEMU boards, for example.
So it makes no sense to have OF_BOARD as a 'choice'. It should be an
option, available with either OF_SEPARATE or OF_EMBED. This would allow
rpi3, for example, to run with the devicetree provided by the prior
bootloader.
This series makes this change, adding various missing devicetree files
(and placeholders) to make the build work.
To make the 'prior stage' side of things more deterministic, a new
OF_HAS_PRIOR_STAGE is added, which cannot be disabled by updated a board's
defconfig. This should help to prevent mistakes.
It also adds a run-time message showing where the devicetree came from,
as well as warnings if the board's expected flow is not being used. This
comes originally from the 'standard passage' series, which depends on
this series.
It also provides a few qemu clean-ups discovered along the way. The
qemu-riscv64_spl problem is fixed.
Please see [2] for discussion on the v6 series.
I put Heinrich's Tested-by tag[3] for the series onto the three devicetree
patches (ARM and RISC-V) that I think it most affects. It isn't possible
to apply a tag to a whole series at present and in any case there are
changes in v7.
Simon Glass [Fri, 17 Dec 2021 03:59:39 +0000 (20:59 -0700)]
fdt: Show a runtime warning based on devicetree source
When running, if the devicetree failed to come from the expected source,
show a warning, e.g:
U-Boot ...
DRAM: 128 MiB
Core: 42 devices, 11 uclasses, devicetree: separate
Warning: Unexpected devicetree source (not from a prior stage)
Warning: U-Boot may not function properly
Flash: 64 MiB
...
These warnings should only appear if the board config has been changed, or
the prior stage is broken.
projects / u-boot.git / log