Michal Simek [Mon, 1 Aug 2016 06:49:12 +0000 (08:49 +0200)]
ARM64: zynqmp: Do not enable DM_MMC by default
The patch:
"dm: mmc: zynq: Convert zynq to use driver model for MMC"
(sha1: 329a449f2c289b4de8f892fca1d9379ce5fd81b8)
added dependency on enabling some MMC options by default.
There are minimal ZynqMP configurations which require
only minimal configurations to be enabled to keep u-boot size
as lower as possible.
Move options to defconfig instead.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 29 Jul 2016 11:03:29 +0000 (13:03 +0200)]
ARM64: zynqmp: Add u-boot,dm-pre-reloc to clk nodes
Serial driver is getting clk information via DT that's why
also clk node needs to have this flag.
Different behavior was introduced by:
"dm: Use dm_scan_fdt_dev() directly where possible"
(sha1: 911954859d6dece49c3e4835faea004cfe392506)
where simple-bus driver starts to call dm_scan_fdt_dev() which has
additional logic around pre_reloc_only parameter which exclude
clk nodes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Hans de Goede [Fri, 29 Jul 2016 09:47:03 +0000 (11:47 +0200)]
sunxi: On newer SoCs use words 1-3 instead of just word 3 from the SID
It seems that bytes 13-14 of the SID / bytes 1-2 from word 3 of the SID
are always 0 on H3 making it a poor candidate to use as source for the
serialnr / mac-address, and the other non constant words (1 and 2) also
have quite a few bits which are the same for some boards,
This commits switches to using the crc32 of words 1 - 3 to get a
more unique value for the mac-address / serialnr.
Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 27 Jul 2016 15:58:06 +0000 (17:58 +0200)]
sunxi: Ensure that the NIC specific bytes of the mac are not all 0
On 2 of my H3 boards bytes 13-15 of the SID are all 0 leading to
the NIC specific bytes of the mac all being 0, which leads to the
boards not getting an ipv6 address from the dhcp server.
This commits adds a check to ensure this does not happen.
Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
sunxi: Hummingbird_A31_defconfig: Drop MACPWR option
MACPWR was used to bring the Ethernet PHY out of reset. The designware
driver now supports the phy reset gpio binding, so this is no longer
needed. In fact in requesting the same GPIO, it makes the designware
driver fail to probe.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi: gpio: Add .xlate function for gpio phandle resolution
sunxi uses a 2 cell phandle for gpio bindings. Also there are no
seperate nodes for each pin bank.
Add a custom .xlate function to map gpio phandles to the correct
pin bank device. This fixes gpio_request_by_name usage.
Fixes: 7aa974858422 ("dm: sunxi: Modify the GPIO driver to support driver
model") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
PopMetal is a rockchip rk3288 based board made by ChipSpark, which has
many interface such as HDMI, VGA, USB, micro-SD card, WiFi, Audio and
Gigabit Ethernet.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
rockchip: add basic support for fennec-rk3288 board
Fennec is a RK3288-based development board with 2 USB ports, HDMI,
micro-SD card, audio and WiFi and Gigabit Ethernet. It also includes
on-board 8GB eMMC and 2GB of SDRAM. Expansion connectors provides access
to display pins, I2C, SPI, UART and GPIOs.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
John Keeping [Mon, 25 Jul 2016 09:02:05 +0000 (10:02 +0100)]
rockchip: rk3288: Fix pinctrl for GPIO bank 0
Bank 0 is the "PMU GPIO" bank which is controlled by the PMU registers
rather than the GRF registers. In the GRF the top half of the register
is used as a mask so that some bits can be updated without affecting the
others, but in the PMU this feature is not provided and the top half of
the register is reserved.
Take the same approach as the Linux driver to update the value via
read-modify-write but setting the mask for only the bits that have
changed. The PMU registers ignore the top 16 bits so this works for
both GRF and PMU iomux registers.
Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch is style-related only, to reformat all the start.S code,
actually not following a coherent style inside single files and
between different cpu start.S files.
Linux format has been respected, as
- max line width at 80 columns
- one 8 cols tab between asm instructions and operands
- inline comments, where any, fixed at col 41
Vignesh R [Fri, 29 Jul 2016 08:52:30 +0000 (14:22 +0530)]
ARM: am57xx_evm: Enable QSPI support
AM571x IDK and AM572x IDK EVMs have spansion s25fl256s QSPI flash on the
board connected to TI QSPI IP over CS0. Therefore enable QSPI support.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
Vignesh R [Fri, 29 Jul 2016 08:52:31 +0000 (14:22 +0530)]
ARM: dts: am57xx-idk-common: Enable support for QSPI
AM571x and AM572x IDK have a spansion s25fl256s QSPI flash on the board
connected to TI QSPI over CS0. Hence, add QSPI and flash slave
DT nodes.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
AM437x SK and AM437x IDK EVMs have 64MB flash, therefore enable
CONFIG_SPI_FLASH_BAR to access flash regions above 16MB.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
Vignesh R [Mon, 25 Jul 2016 10:15:47 +0000 (15:45 +0530)]
ARM: dts: dra7xx: Update spi-max-frequency for QSPI
According to AM572x DM SPRS953A, QSPI max bus speed is 76.8MHz.
Therefore update the spi-max-frequency value of QSPI node for DRA74 and
DRA72 evm. This increase flash read speed by ~2MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Vignesh R [Mon, 25 Jul 2016 10:15:46 +0000 (15:45 +0530)]
configs: dra7xx: Update QSPI speed to 76.8MHz
Now that QSPI driver can support 76.8MHz, update the
CONFIG_SF_DEFAULT_SPEED to the same value.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Vignesh R [Mon, 25 Jul 2016 10:15:45 +0000 (15:45 +0530)]
spi: ti_qspi: dra7xx: Add support to use 76.8MHz clock
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, update
the driver to use the same.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, hence
update QSPI input clock divider value (DPLL_PER_HS13) to provide 76.8MHz
clock, so that driver can use the same.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
Vignesh R [Fri, 22 Jul 2016 05:25:50 +0000 (10:55 +0530)]
spi: ti_qspi: Remove delay in read path for dra7xx
As per commit b545a98f5dc563 ("spi: ti_qspi: Add delay
for successful bulk erase) says its added to meet bulk erase timing
constraints. But bulk erase is a cmd to flash and delay in read path
does not make sense. Morever, testing on DRA74/DRA72 evm has shown that
this delay is no longer required.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Vignesh R [Fri, 22 Jul 2016 05:25:49 +0000 (10:55 +0530)]
spi: ti_qspi: Fix compiler warning when DEBUG macro is set
clk_div is uninitialized at the beginning of ti_spi_set_speed(), move
debug() print after clk_div calculation to avoid compiler warning and to
have proper value of clk_div printed during debugging.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Vignesh R [Fri, 22 Jul 2016 05:25:48 +0000 (10:55 +0530)]
spi: ti_qspi: Fix failure on multiple READ_ID cmd
Populating QSPI_RD_SNGL bit(0x1) in priv->cmd means that value
QSPI_INVAL (0x4) is not written to CMD field of QSPI_SPI_CMD_REG in
ti_qspi_cs_deactivate(). Therefore CS is never deactivated between
successive READ ID which results in sf probe to fail.
Fix this by not populating priv->cmd with QSPI_RD_SNGL and OR it wih
priv->cmd as required (similar to the convention followed in the
driver).
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Stefan Agner [Tue, 26 Jul 2016 05:57:47 +0000 (22:57 -0700)]
mx7_common: initialize generic timer on all CPU's
Use CONFIG_TIMER_CLK_FREQ to let the non-secure init code initialize
the generic timer on all CPU's. This allows to make use of the timer
freuquency register also on other CPU than the start CPU which is
important for KVM.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Stefan Agner [Thu, 21 Jul 2016 04:27:49 +0000 (21:27 -0700)]
colibri_imx7: add Colibri iMX7S/iMX7D module support
This commit adds support for the Toradex Computer on Modules
Colibri iMX7S/iMX7D. The two modules/SoC's are very similar hence
can be easily supported by one board. The board code detects RAM
size at runtime which is one of the differences between the two
boards. The board also uses the UART's in DTE mode, hence making
use of the new DTE support via serial DM.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tim Harvey [Fri, 15 Jul 2016 14:16:29 +0000 (07:16 -0700)]
imx: ventana: add dt fixup for watchdog external reset
Added removal of the fsl,ext-reset-output property in the wdog node for board
revisions that pre-date the addition of the external watchdog reset signal.
This property is a recent addition to mainline linux kernel in order to
specify that the IMX watchdog external reset should be used instead of the
internal chip-level reset.
Tim Harvey [Fri, 15 Jul 2016 14:16:28 +0000 (07:16 -0700)]
imx: ventana: refactor board-specific dt fixups (no functional change)
Re-factor the board-specific dt fixups so that they are easier to follow
and extend in the future:
- use defines for DT paths
- use switch/case per board
- order models numerically
Tim Harvey [Fri, 15 Jul 2016 14:14:25 +0000 (07:14 -0700)]
imx: ventana: make hwconfig initialize based on board configuration
The hwconfig env var allows user to control hardware specific configuration
of board specific features but not all Ventana boards have the same features.
We will use the magic default value of "_UNKNOWN_" to signify that the
bootloader should create this based on detected board model.
Tim Harvey [Wed, 29 Jun 2016 15:58:00 +0000 (08:58 -0700)]
imx: ventana: re-enable late board info display
3b1f681131149b5f62602f582a7e60b0185a2a49 caused a regression that removes
board info dispaly for Gateworks Ventana boards because it made the invalid
assumption that CONFIG_DISPLAY_BOARDINFO_LATE was the same thing as
CONFIG_DISPLAY_BOARDINFO.
Ventana needs to call show_board_info in late init because we need to have
the i2c eeprom based model info. Re-define CONFIG_DISPLAY_BOARDINFO_LATE
to allow that to happen.
Cc: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Fri, 17 Jun 2016 13:20:26 +0000 (06:20 -0700)]
imx: ventana: default pci to disabled
The IMX6 PCIe host controller does not have a proper reset and as such there
are several issues that can arise if PCI is enabled in the bootloader follwed
by Linux trying to re-configure LTSSM and/or toggling PERST# to the devices.
For now, the best approach seems to default to disabling PCI by defaulting
pciedisable=1. This can be overridden by the user if they need PCI in the
bootloader, for example:
- GW552x needing ethernet access in bootloader
- GW16082 expansion board needing a device-tree fixup for irq mapping
Tim Harvey [Fri, 17 Jun 2016 13:10:41 +0000 (06:10 -0700)]
imx: ventana: add dt fixup for GW16082 irq mapping
The GW16082 mini-PCI expansion mezzanine uses a TI XIO2001 PCIe-to-PCI
bridge with legacy INTA/B/C/D interrupts. These interrupts are assigned
in the reverse order according to the PCI spec.
If the TI bridge is found on the Ventana PCI bus, add device-tree nodes
according to bus enumeration explicitly defining the interrupt mapping
to override the default PCI mapping in the Linux kernel. This allows
the GW16082 to work with upstream kernels that support device-tree
irq parsing.
After moving CONFIG_USB_EHCI_MX7 to Kconfig,
the flag must be set in defconfig for mx7dsabresd.
It is already for the not secure config, it is
missing in the secure configuration.
Stephen Warren [Wed, 13 Jul 2016 19:45:31 +0000 (13:45 -0600)]
Add a power domain framework/uclass
Many SoCs allow power to be applied to or removed from portions of the SoC
(power domains). This may be used to save power. This API provides the
means to control such power management hardware.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 5 Jul 2016 23:10:11 +0000 (17:10 -0600)]
arm: Show early-malloc() usage in bdinfo
This is useful information to show how close we are to the limit. At present
it is only available by enabling DEBUG in board_r.c.
Make it available with the 'bdinfo' command also.
Note that this affects ARM only. The bdinfo command is different for each
architecture. Rather than duplicating the code it would be better to
refactor it (as was done with global_data).
Simon Glass [Tue, 5 Jul 2016 23:10:10 +0000 (17:10 -0600)]
dm: Use dm_scan_fdt_dev() directly where possible
Quite a few places have a bind() method which just calls dm_scan_fdt_dev().
We may as well call dm_scan_fdt_dev() directly. Update the code to do this.
Simon Glass [Tue, 5 Jul 2016 23:10:08 +0000 (17:10 -0600)]
dm: core: Add a function to bind child devices
We currently use dm_scan_fdt_node() to bind devices. It is an internal
function and it requires the caller to know whether we are pre- or post-
relocation.
This requirement has become quite common in drivers, so the current function
is not ideal.
Add a new function with fewer arguments, that does not require internal
headers. This can be used directly as a post_bind() method if needed.
Hans de Goede [Tue, 26 Jul 2016 20:26:39 +0000 (22:26 +0200)]
sunxi: Disable sun8i emac driver
Disable the sun8i emac driver for now, there are 2 issues with it:
1) It is causing issues with network connectivity under the kernel driver,
when booting the kernel with v2 of Corentin's sun8i-h3 emac driver, I get
the connection status bouncing between connected at 100mbps full-duplex
and being down every second.
The second issue is that when trying to use it from u-boot
I get a number of unaligned cache flush errors:
=> dhcp
BOOTP broadcast 1
BOOTP broadcast 2
CACHE: Misaligned operation at range [7bf594a8, 7bf59628]
BOOTP broadcast 3
CACHE: Misaligned operation at range [7bf59c90, 7bf59e10]
CACHE: Misaligned operation at range [7bf5a478, 7bf5a5f8]
DHCP client bound to address 10.42.43.80 (1009 ms)
Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
net: sun8i_emac: Drop redundant and incorrect setting of syscon register
In sun8i_emac_board_setup, the driver partially configures the syscon
register for H3 EPHY. However, the settings are incomplete, and
completely unusable. The correct settings are later set in
sun8i_emac_set_syscon, but the incorrect CLK_SEL setting persists.
It is incorrect to use CLK_SEL to select 25 MHz, as the SoC does not
have a 25 MHz clock the EPHY can use.
This patch removes the setting of the syscon register in board_setup,
and also moves set_syscon above mdio_init. While mdio_init does not
access the PHY, it is better to have the PHY parameters setup before
the MDIO bus is registered.
Fixes: a29710c525ff ("net: Add EMAC driver for H3/A83T/A64 SoCs.") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sun8i_emac driver erroneously configures the AHB2 clock when it
assumes it is configuring the AXI gates, which is not even documented
or ever appeared in either the WiP kernel driver or Allwinner's original
driver.
As a result, AHB2 clock mux is set to an invalid setting, making the
EPHY unusable.
Fixes: a29710c525ff ("net: Add EMAC driver for H3/A83T/A64 SoCs.") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Tue, 26 Jul 2016 15:47:16 +0000 (17:47 +0200)]
sunxi: Add defconfig and dts file for the Orange Pi PC Plus SBC
There is a new Orange Pi PC *Plus* version available now,
this is an extended version of the regular Orange Pi PC
with sdio wifi and an eMMC.
The upstream kernel devs have decided that they want a separate
dts for the PC Plus rather then sharing a single dts between the
regular PC and the PC Plus. So add a new orangepi_pc_plus_defconfig
to match.
The added dts file matches the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
York Sun [Fri, 22 Jul 2016 17:52:23 +0000 (10:52 -0700)]
armv8: fsl-layerscape: mmu: Fix enabling MMU
MMU bit in SCTLR needs to be set explicitly after tables are
created. It isn't an issue for EL3 becuase this bit is already
set by early MMU setup. But for other exception levels this
bit was not set.
projects / u-boot.git / log