Peng Fan [Tue, 27 Jan 2015 02:14:03 +0000 (10:14 +0800)]
pmic:pfuze implement pmic_mode_init
This patch is to implement pmic_mode_init function, and add prototype
in header file.
This function is to set switching mode for pmic buck regulators to
improve system efficiency.
Mode:
OFF: The regulator is switched off and the output voltage is discharged.
PFM: In this mode, the regulator is always in PFM mode, which
is useful at light loads for optimized efficiency.
PWM: In this mode, the regulator is always in PWM mode operation
regardless of load conditions.
APS: In this mode, the regulator moves automatically between
pulse skipping mode and PWM mode depending on load conditions.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Fabio Estevam [Mon, 9 Feb 2015 09:29:33 +0000 (07:29 -0200)]
mx53loco: Fix boot hang during reboot stress test
Currently by running the following test:
=> setenv bootcmd reset
=> save
=> reset
, we observe a hang after approximately 20-30 minutes of stress reboot test.
Investigation of this issue revealed that when a single DDR chip select is used,
the hang does not happen. It only happens when the two chip selects are active.
MX53 reference manual states at "28.6.2 Memory ZQ calibration sequence":
"The controller must keep the memory lines quiet (except for CK) for the ZQ
calibration time as defined in the Jedec (512 cycles for ZQCL after reset, 256
for other ZQCL and 64 for ZQCS)."
According to the SDE_0 and SDE_1 bit descriptions from register ESDCTL_ESDCTL:
"Writing 1 to SDE0 or SDE1 will initiate power up delays as JEDEC defines.
Power up delays are a function of the configured memory type (DDR2/DDR3/LPDDR2)"
So make sure to activate one chip select at time (CS0 first and then CS1 later),
so that the required JEDEC delay is respected for each chip select.
With this change applied the board has gone through three days of reboot stress
test without any hang.
Graeme Russ [Sun, 25 Jan 2015 01:07:53 +0000 (12:07 +1100)]
arm: mxs: Add 'Wait for JTAG user' if booted in JTAG mode
When booting in JTAG mode, there is no way to use soft break-points, and
no way of knowing when SPL has finished executing (so the user can issue
a 'halt' command to load u-boot.bin for example)
Add a debug output and simple loop to stop execution at the completion of
the SPL initialisation as a pseudo break-point when booting in JTAG mode
Graeme Russ [Sun, 25 Jan 2015 01:07:52 +0000 (12:07 +1100)]
arm: mxs: Enable booting of mx28 without battery
Section 4.1.2 of Freescale Application Note AN4199 describes the
configuration required to operate the mx28 from a 5V source without a
battery.
This patch changes the behaviour of the dropout control of the DC-DC
converter (refer to section 11.12.9 of the mx28 Application Processor
Reference Manual - Document Number: MCIMX28RM, Rev 2, 08/2013) to the
following:
- Always use 4P2 Linear Regulator if CONFIG_SYS_MXS_VDD5V_ONLY is defined
- Switch between 4P2 Linear Regulator and Battery, using whichever has
the highest voltage if CONFIG_SYS_MXS_VDD5V_ONLY isnot set (this is
the same as the pre-patch behaviour)
Graeme Russ [Sun, 25 Jan 2015 01:07:51 +0000 (12:07 +1100)]
arm: mxs: Add debug outputs and comments to mxs SPL source files
It is difficult to track down fail to boot issues in the mxs SPL.
Implement the following to make it easier:
- Add debug outputs to allow tracing of SPL progress in order to track
where failure to boot occurs. DEUBUG and CONFIG_SPL_SERIAL_SUPPORT must
be defined to enable debug output in SPL
- Add TODO comments where it is not clear if the code is doing what it
is meant to be doing, even tough the board boots properly (these comments
refer to existing code, not to any code added by this patch)
Ye.Li [Wed, 14 Jan 2015 09:18:12 +0000 (17:18 +0800)]
imx: mx6: Fixed AIPS3 base address issue
Should use AIPS3 configuration address 0x0227C000 to set AIPS3,
not the AIPS3 base address.
Additional, replace AIPS1_BASE_ADDR to AIPS3_ARB_BASE_ADDR to align with
AIPS1 and AIPS2, and resolve the AIPS3_ARB_BASE_ADDR undefine problem.
Heiko Schocher [Tue, 20 Jan 2015 09:06:18 +0000 (10:06 +0100)]
arm, imx6, aristainetos: board updates
- use linux display timing settings
- change backlight duty cycle 500ns
- some defaultenvironment changes
- change fit_addr_r to 0x14000000 as needed if
MAX_LOCKDEP_SUBCLASSES in linux gets increased.
- Environment now at 0xd0000 in nand flash
Nikita Kiryanov [Wed, 14 Jan 2015 08:42:54 +0000 (10:42 +0200)]
common: convert compulab splash load code to common code
Move board/compulab/common/splash.c code to
common/splash_source.c to make it available for everybody. This move
renames cl_splash_screen_prepare() to splash_source_load(), and
the compilation of this code is conditional on CONFIG_SPLASH_SOURCE.
splash_source features:
* Provide a standardized way for declaring board specific splash screen
locations
* Provide existing routines for auto loading the splash image from the
locations as declared by the board
* Introduce the "splashsource" environment variable, which makes it
possible to select the splash image source.
cm-t35 and cm-fx6 are updated to use the modified version.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Anatolij Gustschin <agust@denx.de> Reviewed-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Nikita Kiryanov [Wed, 14 Jan 2015 08:42:52 +0000 (10:42 +0200)]
compulab: splash: support loading splash from sf
Add support for loading splash from sf.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[grinberg@compulab.co.il: staticize the sf global variable] Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il>
Nikita Kiryanov [Wed, 14 Jan 2015 08:42:51 +0000 (10:42 +0200)]
compulab: splash: support multiple splash sources
Define a generic way for boards to define splash image locations:
- introduce struct splash_location
- introduce enum splash_storage
- update cl_splash_screen_prepare() to take an array of above struct
and select the appropriate one based on the splashsource environment
variable (if it is not defined- use the first splash location as default).
cm-t35 is updated to work with the new interface.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Nikita Kiryanov [Wed, 14 Jan 2015 08:42:50 +0000 (10:42 +0200)]
compulab: splash: refactor splash.c
Move storage device specific code into its own function instead of
calling it directly from an otherwise storage device independent
function (cl_splash_screen_prepare).
This is a preparation for supporting multiple splash locations.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Nikita Kiryanov [Wed, 14 Jan 2015 08:42:41 +0000 (10:42 +0200)]
arm: mx6: cm-fx6: expand boot sequence
Expand boot sequence to the following order:
1) mmc boot: mmc boot script, then mmc bootm, then mmc bootz.
2) usb boot: usb boot script.
3) sata boot: sata boot script, sata bootm, sata bootz.
4) nand boot: nand bootm, then nand bootz.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Peng Fan [Tue, 30 Dec 2014 09:24:01 +0000 (17:24 +0800)]
imx:mx6sx add dram io configure for mx6sx
Define two structure mx6sx_iomux_ddr_regs and mx6sx_iomux_grp_regs.
Add a new function mx6sx_dram_iocfg to configure dram io.
Since mx6sx only have one channel mmdc0, define a new empty macro MMDC1
to replace mmdc1->entry=value for mx6sx. And to other mx6 soc, MMDC1
effects as "mmdc1->entry=value".
Stefan Roese [Wed, 10 Dec 2014 09:15:23 +0000 (10:15 +0100)]
arm: mx6: Add Barco platinum-picon and platinum-titanium
This patch adds the new Barco platinum platform. It currently
includes those two boards:
platinum-titanium
-----------------
This is the same board as the titanium that is already supported in
mainline U-Boot. But its now moved to this new platform to support
multiple "flavors" of imx6 boards in one directory. Its also moved
to support SPL booting. And with this we use the run-time DDR
configuration of this SPL support. The board is equipped with the
Micron MT41J128M16JT-125 DDR chips. We now can remove the DDR
related registers tuples from the imximage.cfg file. As all this
is done in the SPL at run-time.
platinum-picon
--------------
This board is new and based on the MX6DL with 1GiB DDR using the
Micron MT41K256M16HA DDR3 chips. Its also equipped with 2 NAND
chips (each 512MiB).
Fabio Estevam [Mon, 29 Dec 2014 18:23:17 +0000 (16:23 -0200)]
mx6sxsabresd: Remove unneeded board_late_init()
Since commit 1f98e31bc0b2c37a ("imx: mx6sxsabresd: Use the pfuze common init
function") board_late_init() became empty, so we can safely remove this unneeded
function.
Otavio Salvador [Thu, 15 Jan 2015 15:32:29 +0000 (13:32 -0200)]
wandboard: Use 32bit color depth for Fusion LCD
The Fusion LCD needs the 32bit color depth to properly work; the
default is different on the 3.10.17 kernels and it is better to ensure
it work out of box using proper default color setting.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Masahiro Yamada [Thu, 15 Jan 2015 08:13:24 +0000 (17:13 +0900)]
powerpc: 74xx_7xx: remove 74xx_7xx cpu support
All the 74xx_7xx boards are still non-generic boards:
P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2
Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefan Roese <sr@denx.de> Acked-by: York Sun <yorksun@freescale.com> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Nye Liu <nyet@zumanetworks.com> Cc: Roy Zang <tie-fei.zang@freescale.com>
Simon Glass [Tue, 2 Dec 2014 00:34:07 +0000 (17:34 -0700)]
buildman: Add an option to write the full build output
Normally buildman runs with 'make -s' meaning that only errors and warnings
appear in the log file. Add a -V option to run make in verbose mode, and
with V=1, causing a full build log to be created.
Simon Glass [Tue, 2 Dec 2014 00:34:06 +0000 (17:34 -0700)]
buildman: Add the option to download toolchains from kernel.org
The site at https://www.kernel.org/pub/tools/crosstool/ is a convenient
repository of toolchains which can be used for U-Boot. Add a feature to
download and install a toolchain for a selected architecture automatically.
It isn't clear how long this site will stay in the current place and
format, but we should be able to rely on bug reports if it changes.
Suggested-by: Marek Vašut <marex@denx.de> Suggested-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 2 Dec 2014 00:34:00 +0000 (17:34 -0700)]
buildman: Add an option to use the full tool chain path
In some cases there may be multiple toolchains with the same name in the
path. Provide an option to use the full path in the CROSS_COMPILE
environment variable.
Note: Wolfgang mentioned that this is dangerous since in some cases there
may be other tools on the path that are needed. So this is set up as an
option, not the default. I will need test confirmation (i.e. that this
commit fixes a real problem) before merging it.
Signed-off-by: Simon Glass <sjg@chromium.org> Suggested-by: Steve Rae <srae@broadcom.com>
Simon Glass [Tue, 2 Dec 2014 00:33:57 +0000 (17:33 -0700)]
buildman: Allow specifying a range of commits to build
Adjust the -b flag to permit a range expression as well as a branch.
Signed-off-by: Simon Glass <sjg@chromium.org> Suggested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Simon Glass [Tue, 2 Dec 2014 00:33:56 +0000 (17:33 -0700)]
buildman: Don't remove entire output directory when testing
When running tests the output directory is often wiped. This is only safe if
a branch is being built. The output directory may contain other things
besides the buildman test output.
Simon Glass [Tue, 2 Dec 2014 00:33:55 +0000 (17:33 -0700)]
buildman: Add an option to flatten output directory trees
When building current source for a single board, buildman puts the output
in <output_dir>/current/current/<board>. Add an option to make it use
<output_dir>/<board> instead. This removes the unnecessary directories
in that case, controlled by the --no-subdirs/-N option.
Suggested-by: Tom Rini <trini@ti.com> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 2 Dec 2014 00:33:54 +0000 (17:33 -0700)]
buildman: Try to guess the upstream commit
Buildman normally obtains the upstream commit by asking git. Provided that
the branch was created with 'git checkout -b <branch> <some_upstream>' then
this normally works.
When there is no upstream, we can try to guess one, by looking up through
the commits until we find a branch. Add a function to try this and print
a warning if buildman ends up relying on it.
Also update the documentation to match.
Signed-off-by: Simon Glass <sjg@chromium.org> Suggested-by: Wolfgang Denk <wd@denx.de>
Simon Glass [Tue, 2 Dec 2014 00:33:53 +0000 (17:33 -0700)]
buildman: Don't prune output space for 'current source' build
This is not needed since we always do a full (non-incremental) build. Also
it might be dangerous since it will try to delete everything below the
base directory.
Alexey Brodkin [Tue, 13 Jan 2015 15:49:01 +0000 (18:49 +0300)]
Kconfig: move CONFIG_SYS_CLK_FREQ to Kconfig
It makes sense to specify CONFIG_SYS_CLK_FREQ in "configs/xx_defconfig"
instead of "include/configs/xxx.h" because then header will be reusable
across boards with different CPU clocks.
Also this nice to have an ability for end user to tune this value
himself via "menuconfig".
For now I'm only applying this change to all ARC configs because
otherwise scope of change will be huge.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Tom Rini <trini@ti.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Hans de Goede <hdegoede@redhat.com>
cc: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
Masahiro Yamada [Thu, 8 Jan 2015 10:23:35 +0000 (19:23 +0900)]
spl: spl_nor: surround Linux-load code with #ifdef CONFIG_SPL_OS_BOOT
If CONFIG_SPL_NOR_SUPPORT is defined, spl_nor_load_image() requires
spl_start_uboot(), CONFIG_SYS_OS_BASE, CONFIG_SYS_SPL_ARGS_ADDR,
CONFIG_SYS_FDT_BASE to be defined even if users just want to run
U-Boot, not Linux. This is inconvenient.
This patch is following the codying style of common/spl/spl_nand.c.
Simon Glass [Tue, 2 Dec 2014 20:17:37 +0000 (13:17 -0700)]
bootm: Factor out common parts of image decompression code
Adjust the code so that the error reporting can all be done at the end,
and is the same for each decompression method. Try to detect when
decompression fails due to lack of space. Keep the behaviour of
resetting on failure even though there should be no memory corruption
now.
Simon Glass [Tue, 2 Dec 2014 20:17:31 +0000 (13:17 -0700)]
sandbox: Correct ordering of 'sb save' commands
Prior to commit d455d87 there was an inconsistency between the position of
the 'address' parameter in 'sb load' and 'sb save'. This was corrected but
it broke some tests. Fix the tests and also the help for 'sb save'.
Simon Glass [Tue, 2 Dec 2014 20:17:30 +0000 (13:17 -0700)]
bootm: Move compression progress/error messages into a function
This code is repeated in several places, and does not detect a common
fault where the image is too large. Move it into its own function and
provide a more helpful messages in this case, for compression schemes
which support this.
Simon Glass [Tue, 2 Dec 2014 20:17:29 +0000 (13:17 -0700)]
lzma: fix buffer bound check error further
Commit 4d3b8a0d fixed a problem with lzma decompress where it would
run out of bytes to decompress. The algorithm needs to know how many
uncompressed bytes it is expected to produce.
However, the fix introduced a potential buffer overrun, and causes
the compression test to fail (test_compression command in sandbox).
The correct fix seems to be to use the minimum of the expected number
of uncompressed bytes and the amount of output space available. That
way things work normally when there is enough space, and return an
error (without overrunning available space) when there is not.
Signed-off-by: Antonios Vamporakis <ant@area128.com> CC: Kees Cook <keescook@chromium.org> CC: Simon Glass <sjg@chromium.org> CC: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> CC: Luka Perkov <luka@openwrt.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Wed, 14 Jan 2015 03:35:24 +0000 (12:35 +0900)]
README.scrapyard: fill commit and date fields
This commit was generated by the following command:
scripts/fill_scrapyard.py
The commit-ID of CPCIISER4 removal has been fixed by hand because
the board was removed by commit 370572601027 (ppc4xx: remove CPCIISER4
board), but it was added to README.scrapyard by commit 9a4018e09a2f
(ppc4xx: remove DP405 board).
Hans de Goede [Sun, 11 Jan 2015 18:33:35 +0000 (19:33 +0100)]
sunxi: usbc: Add support for usb-vbus0 controller by axp drivebus pin
The axp221 / axp223's N_VBUSEN pin can be configured as an output rather
then an input, and this is used on some boards to control usb-vbus0, add
support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 11 Jan 2015 18:58:03 +0000 (19:58 +0100)]
sunxi: axp221: Add support for controlling the drivebus pin
The axp221 / axp223's N_VBUSEN pin can be configured as an output rather
then an input, add axp_drivebus_enable() and _disable() functions to set
the pin in output mode and control it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
projects / u-boot.git / log