Igor Prusov [Thu, 9 Nov 2023 10:55:13 +0000 (13:55 +0300)]
clk: Add dump operation to clk_ops
This adds dump function to struct clk_ops which should replace
soc_clk_dump. It allows clock drivers to provide custom dump
implementation without overriding generic CCF dump function.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Tested-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Sean Anderson <seanga2@gmail.com> Signed-off-by: Igor Prusov <ivprusov@sberdevices.ru>
[ Fixed parameter name in documentation ] Signed-off-by: Sean Anderson <seanga2@gmail.com> Link: https://lore.kernel.org/r/20231109105516.24892-6-ivprusov@sberdevices.ru
Tom Rini [Thu, 14 Dec 2023 12:37:02 +0000 (07:37 -0500)]
Merge tag 'u-boot-imx-next-20231214' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx into next
- Add TPM support for venice boards
- Add networking support for imx93-evk
- Enable TCP, IPv6, wget for DHCOM and Data Modul boards
- Enable fastboot support for Toradex boards
- Allow pico-imx7d to boot from SD
- Enable fastboot for beacon imx8m beacon boards, disabled
SYS_CONSOLE_IS_IN_ENV
- Fix mxsboot to prevent NAND blocks being reported as bad
- Add imx8mm PWM clock support
- Several devicetree syncs with the kernel
- Add support for i.MX8MP Polyhex Debix Model A SBC
- Reworked ddr_load_train_firmware() to get a 50ms boot time improvement
Marek Vasut [Wed, 22 Nov 2023 23:37:38 +0000 (00:37 +0100)]
arm64: imx8mp: Enable TCP, IPv6, wget on Data Modul i.MX8M eDM SBC
Enable support for TCP protocol, wget, and IPv6 on this platform.
The former two allow users download payload into the U-Boot from
a web server, which may be more convenient or easier to set up
than TFTP server. The later is enabled to future proof the IP
stack on this platform.
Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Marek Vasut [Sat, 4 Nov 2023 16:32:21 +0000 (17:32 +0100)]
arm64: imx8mp: Enable TCP, IPv6, wget on DH i.MX8MP DHCOM
Enable support for TCP protocol, wget, and IPv6 on this platform.
The former two allow users download payload into the U-Boot from
a web server, which may be more convenient or easier to set up
than TFTP server. The later is enabled to future proof the IP
stack on this platform.
Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Marek Vasut [Sat, 4 Nov 2023 16:32:20 +0000 (17:32 +0100)]
arm: imx6: Enable TCP, IPv6, wget on DH i.MX6 DHCOM
Enable support for TCP protocol, wget, and IPv6 on this platform.
The former two allow users download payload into the U-Boot from
a web server, which may be more convenient or easier to set up
than TFTP server. The later is enabled to future proof the IP
stack on this platform.
Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
bootstd: Fix a memory leak in the efi manager bootflow
efi_get_var() allocates memory which has to be freed after the value of
the variable is consumed. Free the memory properly
Fixes: f2bfa0cb1794 ("bootstd: Make efi_mgr bootmeth work for non-sandbox setups") Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
arm: dts: k3-*-binman: Move to using ti-dm entry type
Move the DM entry in tispl.bin FIT image from default fetching an
external blob entry to fetching using ti-dm entry type. This way, the
DM entry will be populated by the TI_DM pathname if provided. Else it
will resort to the ti-dm.bin file.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com> Reviewed-by: Andrew Davis <afd@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
K3 devices introduces the concept of centralized power, resource and
security management to System Firmware. This is to overcome challenges
by the traditional approach that implements system control functions on
each of the processing units.
The software interface for System Firmware is split into TIFS and DM. DM
(Device Manager) is responsible for resource and power management from
secure and non-secure hosts. This additional binary is necessary for
specific platforms' ROM boot images and is to be packaged into tispl.bin
Add an entry for DM. The entry can be used for the packaging of
tispl.bin by binman along with ATF and TEE.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com> Reviewed-by: Andrew Davis <afd@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
ACPI tables may comprise either RSDT, XSDT, or both. The current code fails
to check the presence of the RSDT table before accessing it. This leads to
an exception if the RSDT table is not provided.
The XSDT table takes precedence over the RSDT table.
The return values of list_rsdt() and list_rsdp() are always zero and not
checked. Remove the return values.
Addresses in the XSDT table are 64-bit. Adjust the output accordingly.
As the RSDT table has to be ignored if the XSDT command is present there is
no need to compare the tables in a display command. Anyway the
specification does not require that the sequence of addresses in the RSDT
and XSDT table are the same.
The FACS table header does not provide revision information. Correct the
description of dump_hdr().
Adjust the ACPI test to match the changed output format of the 'acpi list'
command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* Converting to void * is superfluous when calling memset().
* acpi_fill_header() already fills oem_table_id.
Fixes: d953137526cc ("x86: Move SSDT table to a writer function") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 12 Nov 2023 15:27:48 +0000 (08:27 -0700)]
boot: Move adding initrd earlier in image_setup_libfdt()
This may as well happen before the general event is emitted, so move it.
This will allow us to use the livetree for the event part, but the
flattree for the earlier part.
Simon Glass [Sun, 12 Nov 2023 15:27:47 +0000 (08:27 -0700)]
fdt: ppc: Drop extra size for ramdisk
This code dates from around 2008:
56844a22b76 powerpc: Fix bootm to boot up again with a Ramdisk
Since then we have added FDT relocation which provides enough space
for expansion. We have also added all sorts of fixups earlier in
image_setup_libfdt() which require more space, with ramdisk being the
least of them.
Therefore this extra hack for ramdisk seems unnecessary. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
acpi: move acpi_get_rsdp_addr() to acpi/acpi_table.h
Function acpi_get_rsdp_addr() is needed on all architectures which
write ACPI tables. Move the definition from the x86 include to an
architecture independent one.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 2 Oct 2023 01:15:21 +0000 (19:15 -0600)]
test: lmb: Move tests into the lib suite
These tests are marked as driver model tests, but have nothing to do
with driver model. As a result, they are run as part of 'ut dm' which
only exists for sandbox.
Move them to the 'lib' suite and drop the requirement for initing
devices, since they don't use devices.
Also put the lib_test_lmb_max_regions() macro inside the same #ifdef
as its function, to avoid a build error if the condition is false.
Simon Glass [Mon, 2 Oct 2023 01:15:13 +0000 (19:15 -0600)]
test: Add helper to skip to partial console line
Sometimes we need to skip to a line but it includes addresses or other
information which can vary depending on the runtime conditions.
Add a new ut_assert_skip_to_linen() which is similar to the existing
ut_assert_skip_to_line() function but only checks that the console line
matches up to the length of the provided string.
Benjamin Szőke [Wed, 13 Dec 2023 18:51:49 +0000 (15:51 -0300)]
pico-imx7d: add baseboard SD card boot detect
Technexion PICO-IMX7 SoM is supporting USDHC3 (eMMC or micro SD on SoM)
and USDHC1 (SD on carrier board) to use on any carrier board like
PICO-NYMPH. Based on the U-Boot version from Technexion it adds
baseboard SD card boot detect to able to boot from selected USDHC1
or USDHC3 boot devices.
Signed-off-by: Benjamin Szőke <egyszeregy@freemail.hu> Tested-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Mon, 11 Dec 2023 13:46:17 +0000 (10:46 -0300)]
imx: imx-hab: Select SPL_DRIVERS_MISC in the SPL case
Selecting CONFIG_IMX_HAB=y on a SPL target, such as apalis_imx6_defconfig,
for example, leads to the following build error:
/usr/bin/arm-linux-gnueabihf-ld.bfd: arch/arm/mach-imx/hab.o: in function `imx_hab_is_enabled':
arch/arm/mach-imx/hab.c:879: undefined reference to `fuse_read'
fuse_read() comes from SPL_MXC_OCOTP, which depends on SPL_DRIVERS_MISC,
since commit 251a3053b1e6 ("misc: imx: remove DM dependency for ocotp
driver in SPL").
Select SPL_DRIVERS_MISC in the SPL case to fix this build issue.
Marek Vasut [Wed, 18 Oct 2023 18:51:59 +0000 (20:51 +0200)]
arm: mxs: Clear CPSR V bit to activate low vectors
The MXS starts with CPSR V bit set, which makes the CPU jump to high vectors
in case of an exception. Those high vectors are located at 0xffff0000, which
is where the BootROM exception table is located as well. U-Boot should handle
exceptions on its own using its own exception handling code, which is located
at 0x0, i.e. at low vectors. Clear the CPSR V bit, so that the CPU would jump
to low vectors on exception instead, and therefore run the U-Boot exception
handling code.
Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Tom Rini [Wed, 13 Dec 2023 16:51:53 +0000 (11:51 -0500)]
Merge patch series "bootm: Refactoring to reduce reliance on CMDLINE (part A)"
To quote the author:
It would be useful to be able to boot an OS when CONFIG_CMDLINE is
disabled. This could allow reduced code size.
Standard boot provides a way to handle programmatic boot, without
scripts, so such a feature is possible. The main impediment is the
inability to use the booting features of U-Boot without a command line.
So the solution is to avoid passing command arguments and the like to
code in boot/
A similar process has taken place with filesystems, for example, where
we have (somewhat) separate Kconfig options for the filesystem commands
and the filesystems themselves.
This series starts the process of refactoring the bootm logic so that
it can be called from standard boot without using the command line.
Mostly it removes the use of argc, argv and cmdtbl from the internal
logic.
Some limited tidy-up is included, but this is kept to smaller patches,
rather than trying to remove all #ifdefs etc. Some function comments
are added, however.
A simple programmatic boot is provided as a starting point.
This work will likely take many series, so this is just the start.
Size growth with this series for firefly-rk3288 (Thumb2) is:
arm: (for 1/1 boards) all +23.0 rodata -49.0 text +72.0
but it is not included in this series as it is already large enough.
No functional change is intended in this series.
Changes in v3:
- Add a panic if programmatic boot fails
- Drop RFC tag
Changes in v2:
- Add new patch to adjust position of unmap_sysmem() in boot_get_kernel()
- Add new patch to obtain command arguments
- Fix 'boot_find_os' typo
- Pass in the command name
- Use the command table to provide the command name, instead of "bootm"
Simon Glass [Sat, 18 Nov 2023 21:05:19 +0000 (14:05 -0700)]
bootstd: Introduce programmatic boot
At present bootstd requires CONFIG_CMDLINE to operate. Add a new
'programmatic' boot which can be used when no command line is available.
For now it does almost nothing, since most bootmeths require the
command line.
Simon Glass [Sat, 18 Nov 2023 21:05:16 +0000 (14:05 -0700)]
bootm: Adjust the parameters of bootm_find_images()
Rather than passing it all the command-line args, pass in the pieces
that it needs. These are the image address, the ramdisk address/name
and the FDT address/name.
Ultimately this will allow usage of this function without being called
from the command line.
Move the function comment to the header file and tidy it a little.
Simon Glass [Sat, 18 Nov 2023 21:05:15 +0000 (14:05 -0700)]
bootm: optee: Drop special call to bootm_find_other()
The normal bootm flow calls bootm_find_other() can call the
BOOTM_STATE_FINDOTHER state as part of its processing. Fix the
condition there so that this hack can be removed.
Also drop the confusing check for the OS type, since do_bootm_tee() is
only called if the condition is met - see bootm_os_get_boot_func()
Simon Glass [Sat, 18 Nov 2023 21:05:14 +0000 (14:05 -0700)]
bootm: efi: Drop special call to bootm_find_other()
The normal bootm flow calls bootm_find_other() can call the
BOOTM_STATE_FINDOTHER state as part of its processing. Fix the
condition there so that this hack can be removed.
Simon Glass [Sat, 18 Nov 2023 21:05:13 +0000 (14:05 -0700)]
bootm: Simplify Android ramdisk addr in bootm_find_images()
The Android mechanism uses the loadaddr envrionment-variable to get the
load address, if none is provided. This is equivalent to
image_load_addr so use that instead, converting it to a string as
needed.
This change will permit passing img_addr to this function, in a future
change.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sat, 18 Nov 2023 21:05:09 +0000 (14:05 -0700)]
bootm: Pass image buffer to boot_get_fdt()
Rather than having boot_get_fdt() calculate this, move the calculation
into the caller. This removes the access to argv[0] in this function,
so we can later refactor it to just accept argv[2] instead of the whole
argv[].
Move the function comment to the header file and fix the u8 argument,
while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sat, 18 Nov 2023 21:05:07 +0000 (14:05 -0700)]
fdt: Allow use of fdt_support inside if() statements
Most of the fdt_support.h header file is included only if OF_LIBFDT or
OF_CONTROL are enabled. This means that calling functions defined in
that file must happen inside an #ifdef
This is unnecessary, so reduce the condition to just !USE_HOSTCC
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sat, 18 Nov 2023 21:05:06 +0000 (14:05 -0700)]
bootm: Reduce arguments to boot_get_ramdisk()
This function normally only uses one argument so pass it in directly.
Move comments to the header file so could one day include these
functions in API docs. Fix up the u8 argument while here, since it
avoids the compiler having to mask the value on some machines.
The Android case here is bit strange, since it can use argv[0], so deal
with that in the caller.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sat, 18 Nov 2023 21:05:04 +0000 (14:05 -0700)]
bootm: Move error printing out of boot_get_kernel()
The same error message is printed in two places. Move it out to the
caller so we can avoid passing in the command name. Leave the bootstage
handling where it is.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sat, 18 Nov 2023 21:04:58 +0000 (14:04 -0700)]
bootm: Reduce arguments to boot_get_kernel()
This function only uses one argument and just needs to know the name of
the command which called it. Adjust the function to use only what it
needs. This will make it easier to call from a non-command context.
Tidy up the function comment while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sat, 18 Nov 2023 21:04:57 +0000 (14:04 -0700)]
image: Tidy up genimg_get_kernel_addr_fit()
This function does not modify its first argument, so mark it const. Also
move the comments to the header file and expand them to provide more
useful information.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sat, 18 Nov 2023 21:04:51 +0000 (14:04 -0700)]
mmc: env: Unify the U_BOOT_ENV_LOCATION conditions
The declaration of U_BOOT_ENV_LOCATION() uses a different #ifdef
condition from the code it calls. Use the same condition to avoid a
build warning if CONFIG_CMD_SAVEENV is disabled.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simon Glass [Sat, 18 Nov 2023 21:04:50 +0000 (14:04 -0700)]
README: Correct docs for CONFIG_SPL_BUILD
This option is defined in both SPL and TPL builds, so correct the docs
related to this. Also point to spl_phase() which is normally a better
option. Mention VPL as well.
Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Wed, 13 Dec 2023 16:25:18 +0000 (11:25 -0500)]
Merge patch series "some LED patches"
To quote the author:
I wanted to add support for ti,lp5562, and found an old submission
from Doug. While trying to modify that to work in current U-Boot, I
found a problem with the "move label handling to core" patches.
Patch 1 is a prerequisite for the ti,lp5562 driver, which turned out
to be needed by Christian as well.
Patch 2 is an attempt at (quick-)fixing the mentioned "move label
handling to core" problem. The real fix consists of changing remaining
drivers to not bind the same driver to the top node as to the child
nodes, but I can't test those other drivers.
Patch 3 introduces a helper which should allow removing some
boilerplate in most individual drivers, and 4,5 apply that in the gpio
and pwm drivers. Converting remaining drivers is trivial, but left out
for now.
Finally patch 6 is the reworked lp5562 driver. While I've changed it
to match existing DT bindings (with the goal of making it work with
our .dts that is known to work with the linux driver), most of the
logic is unchanged from Doug's original patch, so he is still listed
as author.
Changes in v2: Interchange order of patches 1 and 2, add a few R-bs,
and try to trim down the commit message in patch 2.
Doug Zobel [Fri, 17 Nov 2023 11:38:11 +0000 (12:38 +0100)]
led: add TI LP5562 LED driver
Driver for the TI LP5562 4 channel LED controller. Supports
independent on/off control of all 4 channels. Supports LED_BLINK on 3
independent channels: blue/green/red. The white channel can blink, but
shares the blue channel blink rate.
Heavily based on patch originally from Doug Zobel [1].
I have modified it so it matches the DT bindings in the linux tree,
and also follows the linux driver implementation more closely. This
should address Tom's concerns, and also matches my goal of making the
U-Boot driver work with our existing .dts which is known to work in
linux.
As our boards only have the R,G,B outputs connected, I have not
actually tested how the white channel behaves, but the R,G,B work
exactly as expected.
Rasmus Villemoes [Fri, 17 Nov 2023 11:38:08 +0000 (12:38 +0100)]
led: introduce led_bind_generic()
All existing drivers in drivers/led/ contain a .bind method that does
exactly the same thing, with just the actual driver name
differing. Create a helper so all those individual methods can be
changed to one-liners.
Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Rasmus Villemoes [Fri, 17 Nov 2023 11:38:07 +0000 (12:38 +0100)]
led-uclass: do not create fallback label for top-level node
Many existing drivers, and led-uclass itself, rely on uc_plat->label
being NULL for the device representing the top node, as opposed to the
child nodes representing individual LEDs. This means that the drivers
whose .probe methods rely on this were broken by commit 83c63f0d1185
("led: Move OF "label" property parsing to core"), and also that the top
node wrongly shows up with 'led list'.
Binding the same driver to the top node as to the individual child
nodes is arguably wrong, and the approach of using a UCLASS_NOP driver
for the top node is probably better - this has for example been done in
commit 01074697801b ("led: gpio: Use NOP uclass driver for top-level
node") and commit 910b01c27c04 ("drivers: led: bcm6753: do not use null
label to find the top")
Until remaining affected drivers are fixed, we can use a heuristic
that only sets the label to the fallback value derived from the node
name if the node does not have a "compatible" property - i.e., if it
has been bound to the LED driver explicitly via
device_bind_driver_to_node(). This is similar to what commit e3aa76644c2a ("led: gpio: Check device compatible string to determine
the top level node") did for gpio_led, but that fix was then supplanted
by commit 01074697801b ("led: gpio: Use NOP uclass driver for top-level
node")
Fixes: 83c63f0d1185 ("led: Move OF "label" property parsing to core") Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Rasmus Villemoes [Fri, 17 Nov 2023 11:38:06 +0000 (12:38 +0100)]
led-uclass: honour ->label field populated by driver's own .bind
If the driver's own .bind method has populated uc_plat->label, don't
override that. This is necessary for an upcoming driver for ti,lp5562,
where the DT binding unfortunately says to use "chan-name" and not
"label".
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
projects / u-boot.git / log