Peter Hoyes [Fri, 31 Mar 2023 08:58:12 +0000 (09:58 +0100)]
vexpress64: Enable VIRTIO_MMIO and RTC_PL031 in the base model
The Arm EBBR (Embedded Base Boot Requirements) require that the time
and basic networking EFI interfaces are available and working, so long
as the hardware has an RTC and network interface.
Arm FVPs typically have a memory-mapped PL031 RTC and a VIRTIO_NET
device defined in the device tree, so "imply" these in the Kconfig for
the FVP base model to simplify creating EBBR-compliant firmware.
Peter Hoyes [Fri, 31 Mar 2023 08:58:11 +0000 (09:58 +0100)]
vexpress64: Use OF_HAS_PRIOR_STAGE for BASE_FVP variant
BASE_FVP now typically uses a devicetree provided by a prior boot stage
(typically Arm TF-A), so imply this option by default when
TARGET_VEXPRESS64_BASE_FVP is selected.
OF_HAS_PRIOR_STAGE selects OF_BOARD so this change is minor, but aligns
TARGET_VEXPRESS64_BASE_FVP with TARGET_VEXPRESS64_BASER_FVP.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Jayesh Choudhary [Tue, 28 Mar 2023 13:02:01 +0000 (18:32 +0530)]
arch: mach-k3: j721s2_init: Disable the firewalls
Some firewalls enabled by ROM are still left on. So some
address space is inaccessible to the bootloader. For example,
in OSPI boot mode we get an exception and the system hangs.
Therefore, disable all the firewalls left on by the ROM.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com> Reviewed-by: Andrew Davis <afd@ti.com> Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Marc Zyngier [Fri, 17 Mar 2023 16:22:52 +0000 (00:22 +0800)]
arm64: Use level-2 for largest block mappings when FEAT_HAFDBS is present
In order to make invalidation by VA more efficient, set the largest
block mapping to 2MB, mapping it onto level-2. This has no material
impact on u-boot's runtime performance, and allows a huge speedup
when cleaning the cache.
Marc Zyngier [Fri, 17 Mar 2023 16:22:51 +0000 (00:22 +0800)]
arm64: Use FEAT_HAFDBS to track dirty pages when available
Some recent arm64 cores have a facility that allows the page
table walker to track the dirty state of a page. This makes it
really efficient to perform CMOs by VA as we only need to look
at dirty pages.
To quote the author:
These patches will use bounce buffers when VIRTIO_F_IOMMU_PLATFORM
feature is in a virtio device.
This feature can be tested with qemu with -device virtio-iommu-pci. So
that when a -device virtio-blk-pci with iommu_platform=true, it will
uses the bounce buffer instead.
Will Deacon [Wed, 29 Mar 2023 14:25:00 +0000 (22:25 +0800)]
virtio: Use bounce buffers when VIRTIO_F_IOMMU_PLATFORM is set
Devices advertising the VIRTIO_F_IOMMU_PLATFORM feature require
platform-specific handling to configure their DMA transactions.
When handling virtio descriptors for such a device, use bounce
buffers to ensure that the underlying buffers are always aligned
to and padded to PAGE_SIZE in preparation for platform specific
handling at page granularity.
Will Deacon [Wed, 29 Mar 2023 14:24:59 +0000 (22:24 +0800)]
virtio: Allocate bounce buffers for devices with VIRTIO_F_IOMMU_PLATFORM
In preparation for bouncing virtio data for devices advertising the
VIRTIO_F_IOMMU_PLATFORM feature, allocate an array of bounce buffer
structures in the vring, one per descriptor.
Will Deacon [Wed, 29 Mar 2023 14:24:58 +0000 (22:24 +0800)]
virtio: Add helper functions to attach/detach vring descriptors
Move the attach and detach logic for manipulating vring descriptors
out into their own functions so that we can later extend these to
bounce the data for devices with VIRTIO_F_IOMMU_PLATFORM set.
Will Deacon [Wed, 29 Mar 2023 14:24:57 +0000 (22:24 +0800)]
virtio: Allocate virtqueue in page-size units
In preparation for explicit bouncing of virtqueue pages for devices
advertising the VIRTIO_F_IOMMU_PLATFORM feature, introduce a couple
of wrappers around virtqueue allocation and freeing operations,
ensuring that buffers are handled in terms of page-size units.
Will Deacon [Wed, 29 Mar 2023 14:24:56 +0000 (22:24 +0800)]
virtio: pci: Tear down VQs in virtio_pci_reset()
The pages backing the virtqueues for virtio PCI devices are not freed
on reset, despite the virtqueue structure being freed as part of the
driver '->priv_auto' destruction at ->remove() time.
Call virtio_pci_del_vqs() from virtio_pci_reset() to free the virtqueue
pages before freeing the virtqueue structure itself.
remoteproc: ti_k3_arm64: Change the startup of arm64 core
Configuring master firewalls require the power of the cluster to be
enabled before configuring them, change the load of rproc to configure
the gtc clocks and start the cluster along with configuring the boot
vector.
Andrew Davis [Thu, 6 Apr 2023 16:38:19 +0000 (11:38 -0500)]
arm: mach-k3: Move sdelay() and wait_on_value() declaration
These probably should be in some system wide header given their use.
Until then move them out of K3 sys_proto.h so we can finish cleaning
that header out.
Signed-off-by: Andrew Davis <afd@ti.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Andrew Davis [Thu, 6 Apr 2023 16:38:15 +0000 (11:38 -0500)]
arm: mach-k3: Make release_resources_for_core_shutdown() common
This function is the same for each device when it needs to shutdown
the R5 core. Move this to the common section and move the remaining
device specific ID list to the device hardware include.
Signed-off-by: Andrew Davis <afd@ti.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Andrew Davis [Thu, 6 Apr 2023 16:38:11 +0000 (11:38 -0500)]
arm: mach-k3: Move J721e SoC detection out of common section
This belongs in the J721e specific file as it is the only place
this is used. Any board level users should use the SOC driver.
While here, move the J721e and J7200 SoC IDs out of sys_proto.h
and into hardware.h. Use a macro borrowed from Rockchip and add
the rest of the SoC IDs for completeness and later use.
Signed-off-by: Andrew Davis <afd@ti.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Andrew Davis [Thu, 6 Apr 2023 16:38:10 +0000 (11:38 -0500)]
arm: mach-k3: Move MSMC fixup to SoC level
The MSMC fixup is something we do based on SoC, not based on the board.
So this fixup does not belong in the board files. Move this to the
mach-k3 common file so that it does not have to be done in each board
that uses these SoCs.
We use ft_system_setup() here instead of ft_board_setup() since it is no
longer board level. Enable OF_SYSTEM_SETUP in the configurations that use
this to keep functionality the same.
Signed-off-by: Andrew Davis <afd@ti.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Tom Rini [Sun, 23 Apr 2023 16:15:56 +0000 (12:15 -0400)]
Merge tag 'u-boot-rockchip-20230421' of https://source.denx.de/u-boot/custodians/u-boot-rockchip
- Add rk3588 evb support;
- Update pinctrl for rk3568 and rk3588;
- Update rk3288 dts;
- Update mmc support for rk3568 and rk3588;
- Add rng support for rk3588;
- Add DSI support for rk3568;
- Some other misc fixes in dts, config, driver;
- watchdog: arm_smc_wdt: add watchdog support (Lionel)
- watchdog: ftwdt010: return a previously deleted driver now ported to
DM (Sergei)
- watchdog: Add a watchdog driver for Raspberry Pi boards (Etienne)
For BRCMNAND with 1-bit BCH ECC (BCH-1) such as used on the
D-Link DIR-885L and DIR-890L routers, we need to explicitly
select the ECC like this in the device tree:
This is handled by the Linux kernel but U-Boot core does
not respect this. Fix it up by parsing the algorithm and
preserve the behaviour using this property to select
software BCH as far as possible.
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: William Zhang <william.zhang@broadcom.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm] Link: https://lore.kernel.org/all/20230407134008.1939717-3-linus.walleij@linaro.org/ Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Peter Geis [Tue, 18 Apr 2023 16:46:44 +0000 (16:46 +0000)]
mmc: sdhci: Allow disabling of SDMA in SPL
Rockchip emmc devices have a similar issue to Rockchip dwmmc devices,
where performing DMA to SRAM later causes issues with suspend/resume.
Allow us to toggle SDMA in SPL for sdhci similar to ADMA support, so we
can ensure DMA is not used when loading the SRAM code.
Signed-off-by: Peter Geis <pgwipeout@gmail.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
[jonas@kwiboo.se: add Kconfig default value and fix ADMA typo] Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Jonas Karlman [Tue, 18 Apr 2023 16:46:39 +0000 (16:46 +0000)]
mmc: rockchip_sdhci: Add support for RK3588
Add support for RK3588 to the rockchip sdhci driver.
Use driver data to handle differences between RK3568 and RK3588:
- Set "Receive original clock source is auto gating" for RK3588.
- Set "Receive clock source is no-inverted" only on RK3568 and "Transmit
clock source is invertion of original clock input" for RK3588.
- Use different txclk_tapnum for HS400 modes on RK3588.
- Configure the CMDOUT reg for HS400 modes for RK3588.
This is based on the mainline linux and vendor kernel driver and have
successfully been tested with rock5b-rk3588_defconfig and
Jonas Karlman [Tue, 18 Apr 2023 16:46:35 +0000 (16:46 +0000)]
mmc: rockchip_sdhci: Rearrange and simplify used regs and flags
This rearrange and remove duplicate defines to make the code cleaner.
There is no need to read vendor area1 and use an offset each time, it is
easier and clearer to just use the reg offset defined in TRM, same as
the other vendor regs.
This also removes use of the misspelled const for the RK3588 CMDOUT reg,
it will be re-added when support for RK3588 is introduced.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Tue, 18 Apr 2023 16:46:34 +0000 (16:46 +0000)]
mmc: rockchip_sdhci: Remove empty get_phy and set_enhanced_strobe ops
Remove empty implementations of get_phy and set_enhanced_strobe ops.
Change driver set_enhanced_strobe to return 0 in order to allow missing
implementation of the ops.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Tue, 18 Apr 2023 16:46:33 +0000 (16:46 +0000)]
mmc: rockchip_sdhci: Update speed mode controls in set_ios_post
Refactor set_ios_post ops to correctly set UHS Speed Select field values
according to TRM. Also set or unset Enhanced Strobe Enable bit and
eMMC Card present bit in set_ios_post, the Enhanced Strobe Enable bit
was never unset after switching to HS400ES mode.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Check return value from mmc_send_cmd and clear HOST_CONTROL2 when there
is an error. Also skip enable of interrupt signaling and remove a delay,
a delay is already happening in sdhci_send_command.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove the unneeded emmc_phy_init now that the no-inverter flag is
handled correctly after commit 2321a991bbb5 ("rockchip: sdhci: rk3568:
bypass DLL when clk <= 52 MHz").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Tue, 18 Apr 2023 16:46:24 +0000 (16:46 +0000)]
mmc: sdhci: Set UHS Mode Select field for UHS SDR25 mode
Set correct UHS Mode Select field value for UHS SDR25 (50MHz) mode.
Fixes: d1c0a2200afb ("mmc: sdhci: Add support for HOST_CONTROL2 and setting UHS timings") Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Thu, 13 Apr 2023 14:13:03 +0000 (09:13 -0500)]
ARM: dts: rockchip: rk3588s-u-boot: Add rng node
Add a node for the trng found on RK3588 SoCs.
Changes in V3:
- Added Reviewed-By tag.
Changes in V2:
- None
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Chris Morgan [Thu, 13 Apr 2023 14:13:02 +0000 (09:13 -0500)]
rockchip: rng: add trngv1 for rk3588
This adds support for the TRNG found in the RK3588 SoC to the
rockchip_rng driver so that it can be used for things such as
seeding randomness to Linux.
Changes in V3:
- Moved notes from commit to cover letter.
- Added Reviewed-By tag.
Changes in V2:
- Modified Kconfig to note that the Rockchip RNG driver supports all
versions of the hardware (v1, v2, and the trng in the rk3588).
Signed-off-by: Lin Jinhan <troy.lin@rock-chips.com> Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Mon, 17 Apr 2023 19:07:25 +0000 (19:07 +0000)]
clk: rockchip: rk3568: Add dummy I2S1_MCLKOUT_TX clock support
A RK3568 device tree pmic node can reference the I2S1_MCLKOUT_TX clock
in assigned-clocks, add dummy support to set parent of this clock to the
rk3568 cru driver.
Fixes probe of pmic driver and missing regulators on affected boards,
rk3568-evb and rk3568-rock-3a.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Mon, 17 Apr 2023 19:07:23 +0000 (19:07 +0000)]
pinctrl: rockchip: Fix IO mux selection on RK3568
IO mux selection is not working correctly for all pins. Sync mux route
data from linux to add any missing and update wrong trigger pins to fix
this. Also apply the pull-up fix needed for GPIO0 D3-D6.
Jonas Karlman [Mon, 17 Apr 2023 19:07:21 +0000 (19:07 +0000)]
rockchip: rk3588: Sync sdmmc node from linux-next
Sync the sdmmc node from linux-next, include required nodes in SPL and
imply Kconfig options required for functional sdmmc clk in SPL and
U-Boot proper.
This make it possible for both SPL and U-Boot proper to configure sdmmc
clocks. In SPL, before TF-A is loaded, scru regs is configured, in
U-Boot proper a SCMI message is sent to TF-A.
Fixes: 95c8656b72dc ("ARM: dts: rockchip: rk3588s-u-boot: Add sdmmc node") Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Mon, 17 Apr 2023 19:07:20 +0000 (19:07 +0000)]
rockchip: rk3588: Add support for sdmmc clocks in SPL
Booting from sdmmc on RK3588 currently works because of a workaround in
the device tree, clocks are reordered so that the driver use ciu-sample
instead of ciu, and the BootRom initializes sdmmc clocks before SPL is
loaded into DRAM.
The sdmmc clocks are normally controlled by TF-A using SCMI. However,
there is a need to control these clocks in SPL, before TF-A has started.
This adds a rk3588_scru driver to control the sdmmc clocks in SPL before
TF-A has started, using scru regs. It also adds a small glue driver to
bind the scmi clock node to the rk3588_scru driver in SPL.
Fixes: 7a474df74023 ("clk: rockchip: Add rk3588 clk support") Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Mon, 17 Apr 2023 19:07:18 +0000 (19:07 +0000)]
clk: scmi: Add Kconfig option for SPL
Building U-Boot SPL with CLK_SCMI and SCMI_FIRMWARE Kconfig options
enabled and SPL_FIRMWARE disabled result in the following error.
drivers/clk/clk_scmi.o: in function `scmi_clk_gate':
drivers/clk/clk_scmi.c:84: undefined reference to `devm_scmi_process_msg'
drivers/clk/clk_scmi.c:88: undefined reference to `scmi_to_linux_errno'
drivers/clk/clk_scmi.o: in function `scmi_clk_get_rate':
drivers/clk/clk_scmi.c:113: undefined reference to `devm_scmi_process_msg'
drivers/clk/clk_scmi.c:117: undefined reference to `scmi_to_linux_errno'
drivers/clk/clk_scmi.o: in function `scmi_clk_set_rate':
drivers/clk/clk_scmi.c:139: undefined reference to `devm_scmi_process_msg'
drivers/clk/clk_scmi.c:143: undefined reference to `scmi_to_linux_errno'
drivers/clk/clk_scmi.o: in function `scmi_clk_probe':
drivers/clk/clk_scmi.c:157: undefined reference to `devm_scmi_of_get_channel'
make[1]: *** [scripts/Makefile.spl:527: spl/u-boot-spl] Error 1
make: *** [Makefile:2043: spl/u-boot-spl] Error 2
Add Kconfig option so that CLK_SCMI can be disabled in SPL to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Mon, 17 Apr 2023 19:07:15 +0000 (19:07 +0000)]
rockchip: rk35xx: Fix boot with a large fdt blob
The TF-A blobs used to boot RK3568 and RK3588 boards is based on atf
v2.3. Mainline atf v2.3 contains an issue that could lead to a crash
when it fails to parse the fdt blob being passed as the platform param.
An issue that was fixed in atf v2.4.
The vendor TF-A seem to suffer from a similar issue, and this prevents
booting when fdt blob is large enough to trigger this condition.
Fix this by implying SPL_ATF_NO_PLATFORM_PARAM to let u-boot pass a
NULL pointer instead of the fdt blob as the platform param.
This fixes booting Radxa ROCK 3A after recent sync of device tree.
Fixes: 073d911ae64a ("rockchip: rk3568-rock-3a: Sync device tree from linux") Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Jonas Karlman [Mon, 17 Apr 2023 19:07:14 +0000 (19:07 +0000)]
rockchip: rk3588-rock-5b: Fix sdmmc boot
Running U-Boot from a SD-card on ROCK 5 Model B fails to load atf using
DMA and prints debug_uart messages.
<debug_uart>
<debug_uart>
U-Boot SPL 2023.04-rc3 (Mar 12 2023 - 00:30:16 +0000)
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-1' image node
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Use fifo-mode to disable DMA in SPL, add same-as-spl to boot-order and
remove DEBUG_UART_ANNOUNCE option to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
John Keeping [Mon, 27 Mar 2023 11:01:10 +0000 (12:01 +0100)]
rockchip: otp: fix misc_read() return values
The documentation for misc_read() says:
Return: number of bytes read if OK (may be 0 if EOF), -ve on error
The Rockchip efuse driver implements this so it should return the number
of bytes read rather than zero on success. Fix this so that the driver
follows the usual contract for read operations.
Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
John Keeping [Mon, 27 Mar 2023 11:01:09 +0000 (12:01 +0100)]
rockchip: efuse: fix misc_read() return values
The documentation for misc_read() says:
Return: number of bytes read if OK (may be 0 if EOF), -ve on error
The Rockchip efuse driver implements this so it should return the number
of bytes read rather than zero on success. Fix this so that the driver
follows the usual contract for read operations.
Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
projects / u-boot.git / log