Stefan Roese [Mon, 29 Jun 2009 11:30:50 +0000 (13:30 +0200)]
UBI: Fix build problem noticed on Apollon (arm/testing repo)
This patch fixes a build problem noticed on Apollon by using
mtd_dev_by_eb() instead of "/" as done in the Linux UBI version.
So this brings the U-Boot UBI version more in sync with the Linux
version again.
Mike Frysinger [Fri, 19 Jun 2009 07:20:06 +0000 (03:20 -0400)]
sf: sst: fix sector size
Looks like when I was encoding the sector sizes, I forgot to divide by 8
(due to the stupid marketing driven process that declares all sizes in
useless megabits and not megabytes).
arm nomadik: use 1000 as HZ value and rewrite timer code
This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller. Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.
Signed-off-by: Alessandro Rubini <rubini@unipv.it> Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Thomas Lange [Sat, 20 Jun 2009 09:02:17 +0000 (11:02 +0200)]
ARM DaVinci: EMIF settings
NAND module should not modify EMIF registers unrelated to CS2
that is used for NAND, i.e. do not modify EWAIT config register
or registers for other Chip Selects.
Without this patch, EMIF configurations made in board_init()
will be invalidated.
Sedji Gaouaou [Wed, 24 Jun 2009 06:32:09 +0000 (08:32 +0200)]
at91sam9260/9263: add back up for the rst(reset controller).
On the boards at91sam9260ek, at91sam9263ek and afed9260, the rstc register was
set to 0 after being set to 500 ms for the PHY reset.
Do backup the old reset length and restore it after the MACB initialisation.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com> Signed-off-by: Stelian Pop <stelian@popies.net>
Kumar Gala [Fri, 3 Jul 2009 17:45:44 +0000 (12:45 -0500)]
fsl: Fix compiler warnings from gcc-4.4 in sys_eeprom code
sys_eeprom.c: In function 'do_mac':
sys_eeprom.c:323: warning: dereferencing type-punned pointer will break strict-aliasing rules
sys_eeprom.c: In function 'mac_read_from_eeprom':
sys_eeprom.c:395: warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Tue, 30 Jun 2009 22:15:51 +0000 (17:15 -0500)]
83xx: Add support for fsl_dma driver
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu> Tested-by: Ira W. Snyder <iws@ovro.caltech.edu> Acked-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Tue, 30 Jun 2009 22:15:50 +0000 (17:15 -0500)]
83xx: Replace CONFIG_ECC_INIT_VIA_DDRC references
Update 83xx architecture's CONFIG_ECC_INIT_VIA_DDRC references to
CONFIG_ECC_INIT_VIA_DDRCONTROLLER, which other Freescale architectures
use
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Acked-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
8xxx: Second UART port added for MPC85xx, MPC83xx, MPC86xx processors
Defining the next two configs allows to switch the serial port from the
console using the setenv stdin and stdout
1. #define CONFIG_SERIAL_MULTI 1 /* Enable both serial ports */
2. #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Wed, 1 Jul 2009 21:51:59 +0000 (16:51 -0500)]
fsl_ddr: Fix DDR3 calculation of rank density with 8GB or more
The calculate for rank density in compute_ranksize() for DDR3 used all
integers for the expression, so the result was also a 32-bit integer, even
though the 'bsize' variable is a u64. Fix the expression to calculate a
true 64-bit value.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Tue, 30 Jun 2009 22:15:49 +0000 (17:15 -0500)]
fsl_dma: Make DMA transactions snoopable
Make DMA transactions snoopable so that CPUs can keep caches up-to-date.
This allows dma transactions to be used for operations such as memory
copies without any additional cache control operations.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Tue, 30 Jun 2009 22:15:44 +0000 (17:15 -0500)]
fsl_dma: Fix Channel Start bug in dma_check()
The Channel Start (CS) bit in the Mode Register (MR) should actually be
cleared as the comment in the code suggests. Previously, CS was being
set, not cleared.
Assuming normal operation of the DMA engine, this change shouldn't have
any real affect.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 18 Jun 2009 13:39:42 +0000 (08:39 -0500)]
8xxx: Fix PCI bus address setup for 36-bit configs
We want the outbound PCI memory map to end at the 4G boundary so we
can maximize the amount of space available for inbound mappings if
we have large amounts of memory.
This matches the device tree setup in the kernel for the 36-bit physical
configs for the platforms that have one (MPC8641 HPCN & MPC8572 DS).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 18 Jun 2009 13:23:01 +0000 (08:23 -0500)]
86xx: Add CPU_TYPE_ENTRY support
Unify with 83xx and 85xx and use CPU_TYPE_ENTRY. We are going to use
this to convey the # of cores and DDR width in the near future so its
good to keep in sync.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Meerwald [Mon, 29 Jun 2009 19:48:33 +0000 (15:48 -0400)]
Blackfin: TWI/I2C: fix pure writes
If doing a pure write with register address and data (not a read/write
combo transfer), we don't set the initial transfer length properly which
ends up causing only the register address to be transferred.
While we're here, fix the i2c_write() parameter description of the buffer.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Minkyu Kang [Thu, 25 Jun 2009 10:21:33 +0000 (19:21 +0900)]
s3c64xx: move the reset_cpu function
Because of the reset_cpu is soc specific, should be move to soc
And read reset value from SYS_ID register instead of hard code
this patch also supports s3c6410
Magnus Lilja [Sat, 13 Jun 2009 18:50:01 +0000 (20:50 +0200)]
MX31: Add NAND SPL for i.MX31.
This patch adds the NAND SPL framework needed to boot i.MX31 boards
from NAND.
It has been tested on a i.MX31 PDK board with large page NAND. Small
page NANDs should work as well, but this has not been tested.
Note: The i.MX31 NFC uses a non-standard layout for large page NANDs,
whether this is compatible with a particular setup depends on how
the NAND device is programmed by the flash programmer (e.g. JTAG
debugger).
The patch is based on the work by Maxim Artamonov.
Signed-off-by: Maxim Artamonov <scn1874@yandex.ru> Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Magnus Lilja [Sat, 13 Jun 2009 18:50:00 +0000 (20:50 +0200)]
ARM1136: Introduce CONFIG_PRELOADER macro.
Currently CONFIG_ONENAND_IPL is used in a number of #ifdef's
in start.S. In preparation for adding support for NAND SPL
the macro CONFIG_PRELOADER is introducted and replaces the
CONFIG_ONENAND_IPL in start.S.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Vivi Li [Fri, 12 Jun 2009 10:53:22 +0000 (10:53 +0000)]
Blackfin: bf533-stamp/bf537-stamp: fix env settings for SPI flash
The SPI flash layer is much stricter about sector usage than the eeprom
layer we used to use, so update the env settings to better match the
sector alignment of the flashes we use.
Signed-off-by: Vivi Li <vivi.li@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Vivi Li [Fri, 12 Jun 2009 10:33:23 +0000 (10:33 +0000)]
Blackfin: bump up default JTAG console timeout
The debug tools that interface with the other side of the JTAG console
got much slower when generalizing things, so bump up the default timeout
value on the U-Boot side to cope. Hopefully at some point we can improve
the debug tools to speed things back up.
Signed-off-by: Vivi Li <vivi.li@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
s-paulraj@ti.com [Tue, 12 May 2009 15:45:34 +0000 (11:45 -0400)]
DaVinci Network Driver Updates
Different flavours of DaVinci SOC's have differences in their EMAC IP
This patch does the following
1) Updates base addresses for DM365
2) Updates MDIO frequencies for DM365 and DM646x
3) Update EMAC wrapper registers for DM365 and DM646x
Patch applies to u-boot-net git. the EMAC driver itself
will be updated shortly to add support for DM365 and DM646x
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Subject: [PATCH] [repost] Standardize the use of MCFFEC_TOUT_LOOP as a udelay(1) loop counter.
From 584b5fbd4abfc43f920cc1c329633e03816e28be Mon Sep 17 00:00:00 2001
From: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Date: Wed, 20 May 2009 18:26:01 -0400
Subject: [PATCH] Standardize the use of MCFFEC_TOUT_LOOP as a udelay(1) loop counter.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
A VLAN tagged DHCP request/discover is 4 bytes short
The problem is that BOOTP_SIZE uses ETHER_HDR_SIZE which is 14 bytes.
If sending a VLAN tagged frame (when env variable vlan is set) this
should be VLAN_ETHER_HDR_SIZE=18 which is what NetSetEther returns.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@aimvalley.nl> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
projects / u-boot.git / log