Wenyou Yang [Thu, 13 Apr 2017 02:31:20 +0000 (10:31 +0800)]
board: sama5d4ek: clean up code
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Wenyou Yang [Thu, 13 Apr 2017 02:31:19 +0000 (10:31 +0800)]
board: sama5d4ek: update to support DM/DT
Update the configuration files to support the device tree and driver
model, so do SPL. The device clock and pins configuration are handled
by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Wenyou Yang [Thu, 13 Apr 2017 02:31:17 +0000 (10:31 +0800)]
board: sama5d4_xplained: clean up code
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Wenyou Yang [Thu, 13 Apr 2017 02:31:16 +0000 (10:31 +0800)]
board: sama5d4_xplained: update to support DM/DT
Update the configuration files to support the device tree and
driver model, so do SPL. The device clock and pins configuration
are handled by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Wenyou Yang [Fri, 24 Mar 2017 03:34:06 +0000 (11:34 +0800)]
ARM: at91: lds: use "_image_binary_end" for DT location
The MMC SPL locates the BSS section to a different memory region
from text, then use "_image_binary_end" variable to point to the
correct device tree location.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Wenyou Yang [Fri, 24 Mar 2017 01:18:44 +0000 (09:18 +0800)]
ARM: dts: at91: add dts file for sama5d4ek
Add the device tree file for sama5d4ek board.
The dts file is copied from Linux-4.4, do the following changes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Wenyou Yang [Fri, 24 Mar 2017 01:18:43 +0000 (09:18 +0800)]
ARM: dts: at91: add dts files for sama5d4 Xplained
Add the device tree files for sama5d4 Xplained board.
The dts files are copied from Linux-4.4, do the following changes.
- add reg property for pinctrl node.
- move the gpio nodes(pioA, pioB, pioC ...) from the pinctrl child's
nodes to its slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Wenyou Yang [Fri, 24 Mar 2017 01:18:42 +0000 (09:18 +0800)]
ARM: at91: dt: add dts file for sama5d3 Xplained
Add the device tree file for sama5d3 Xplained board.
The dts files are copied from the Linux-4.9, do changes as below.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Wenyou Yang [Fri, 24 Mar 2017 01:18:41 +0000 (09:18 +0800)]
ARM: at91: dt: add dts files for sama5d3xek board
Add the device tree files for sama5d3xek board.
The dts files are copied from Linux-4.9, do the changes as below.
- add reg property for the pinctrl node.
- move the gpio nodes (pioA, pioB, pioC ...) as the pinctrl's
slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
- add spi0 node aliases.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Wenyou Yang [Thu, 23 Mar 2017 04:44:37 +0000 (12:44 +0800)]
pinctrl: at91: add pinctrl driver
AT91 PIO controller is a combined gpio-controller, pin-mux and
pin-config module. The peripheral's pins are assigned through
per-pin based muxing logic.
Each SoC will have to describe the its limitation and pin
configuration via device tree. This will allow to do not need
to touch the C code when adding new SoC if the IP version is
supported.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Thu, 23 Mar 2017 04:55:21 +0000 (12:55 +0800)]
mtd: nand: atmel: use another functions to set gpio value
Because there isn't the implementation of gpio_set/get_value()
and gpio_set/get_value() after the at91 gpio driver is converted
to support the driver model, use at91_set_gpio_value() and
at91_get_gpio_value()
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Thu, 23 Mar 2017 04:55:20 +0000 (12:55 +0800)]
ARM: at91: gpio: fix at91_set_gpio_value() define
When the CONFIG_ATMEL_LEGACY is undefined, according to the following
defines, at91_set_gpio_value() references to at91_set_pio_value(x, y)
with two parameters.
#define at91_set_gpio_value(x, y) at91_set_pio_value(x, y)
#define at91_get_gpio_value(x) at91_get_pio_value(x)
But there isn't the implementation of at91_set_pio_value(x, y) with
two parameters in U-Boot. This is an error.
Same as at91_get_gpio_value(x) define.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Not force to use python from PATH. Issue was noted when building with
Yocto, because python from the distro is always taken instead of
python-native built during Yocto process.
Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 4 Apr 2017 19:00:19 +0000 (13:00 -0600)]
dm: core: Ensure DMA regions start up with the cache clean
There is a strange interaction with drivers which use DMA if the cache
starts off in a dirty state. Buffer space which the driver reads (but has
not previously written) can contain zero bytes from alloc_priv(). This can
cause corruption of the memory used by DMA for incoming data.
Fix this and add a comment to explain the problem.
This allows the dwc2 driver to work correctly with driver model, for
example.
core/uclass: Print name of device in uclass_find_device_by_seq()
uclass_find_device_by_seq() prints seq and req_seq when debugging is
enabled, but this information is not very useful by itself. Add the
name of he driver to this information. This improves debugging as it
shows which devices are being considered.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Simon Glass <sjg@chromium.org>
With Python 3.5.2 encode will throw an exception if val is a byte array.
Decode it to a string first. This assumes it's utf-8, if it's not valid
utf-8 it will throw an exception.
Signed-off-by: George McCollister <george.mccollister@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
os.read() returns a byte array in Python 3.5.2 and needs to be converted
into a string. Check if the returned value is an instance of bytes and
if it is decode it as a utf-8 string. If it is not a utf-8 encoded string
the decoding may fail with an exception.
Prior to this fix the comparisions check data == "" would fail when data
was b'' and would cause an infinite memory leaking loop. joins would
also fail with an exception below but due to the infinite loop it never
made it that far.
Signed-off-by: George McCollister <george.mccollister@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
serial: ns16550: Link in the DM driver when when using platdata
Do not condition the compilation of the U_BOOT_DRIVER by !OF_PLATDATA.
This is inconsistent with the majority of other drivers. This also
blocks OF_PLATDATA boards with an 16550-compatible serial from using
serial in SPL.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Added tweak for rock to avoid a TPL build failure: Signed-off-by: Simon Glass <sjg@chromium.org>
ARCv2: SLC: Make sure busy bit is set properly on SLC flushing
As reported in STAR 9001165532, an SLC control reg read (for checking
busy state) right after SLC invalidate command may incorrectly return
NOT busy causing software to NOT spin-wait while operation is underway.
(and for some reason this only happens if L1 cache is also disabled - as
required by IOC programming model)
Suggested workaround is to do an additional Control Reg read, which
ensures the 2nd read gets the right status.
Stefan Agner [Wed, 29 Mar 2017 19:41:23 +0000 (12:41 -0700)]
libfdt: fix build with Python 3
For some reason Python 3 seems to think it does not need to build
the library. Using the --force parameter makes sure that the library
gets built always. This is especially important since we move the
library in the next step of the Makefile, hence forcing a rebuild
every time the higher level Makefile triggers a rebuild is required
to make sure the library is always there.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Simon Glass <sjg@chromium.org>
Joel Stanley [Sun, 9 Apr 2017 18:33:58 +0000 (20:33 +0200)]
Makefile: Fix linking with modern binutils
Since Binutils 1a9ccd70f9a7[1] u-boot will not link targets that set
CONFIG_SYS_TEXT_BASE=0 with the following error:
LD u-boot
arm-linux-gnueabi-ld.bfd: u-boot: Not enough room for program headers, try
linking with -N
arm-linux-gnueabi-ld.bfd: final link failed: Bad value
The issue can be reproduced with the bad binutils and the rock2_defconfig
target.
This issue was also encountered by the powerpc kernel[2], with the fix
being to pass --no-dynamic-linker for linkers newer than 2.26 when this
flag was introduced. The option tells ld that the PIE or shared lib does
not need loaded program headers.
Ubuntu Zesty's Binutils 2.27.51.20161202 hits this error.
Signed-off-by: Joel Stanley <joel@jms.id.au>
[AF: Apply to LDFLAGS_$(SPL_BIN) as well, suggested by Tom Rini] Signed-off-by: Andreas Färber <afaerber@suse.de>
Andy Shevchenko [Sat, 1 Apr 2017 13:21:34 +0000 (16:21 +0300)]
x86: Introduce minimal PMU driver for Intel MID platforms
This simple PMU driver allows to tyrn power on and off for selected
devices. In particularly Intel Tangier needs to power on SDHCI
controllers in order to access to them during board initialization.
In the future it might be expanded to cover other Intel MID platforms,
that's why it's located under arch/x86/lib and called pmu.c.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Felipe Balbi [Sat, 1 Apr 2017 13:21:33 +0000 (16:21 +0300)]
x86: Add SCU IPC driver for Intel MID platforms
Intel MID platforms have few microcontrollers inside SoC, one of them
is so called System Controller Unit (SCU).
Here is the driver to communicate with microcontroller.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Simon Glass <sjg@chromium.org>
Andy Shevchenko [Tue, 28 Feb 2017 12:04:10 +0000 (14:04 +0200)]
serial: Add serial driver for Intel MID
Add a specific serial driver for Intel MID platforms.
It has special fractional divider which can be programmed via UART_PS,
UART_MUL, and UART_DIV registers.
The UART clock is calculated as
UART clock = XTAL * UART_MUL / UART_DIV
The baudrate is calculated as
baud rate = UART clock / UART_PS / DLAB
Initialize fractional divider correctly for Intel Edison platform.
For backward compatibility we have to set initial DLAB value to 16
and speed to 115200 baud, where initial frequency is 29491200Hz, and
XTAL frequency is 38.4MHz.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Stefan Roese [Fri, 31 Mar 2017 06:09:39 +0000 (08:09 +0200)]
x86: bootm: Fix FIT image booting on x86
Checking 'is_zimage' at this time will always fail and therefore booting
a FIT style image will always lead to this error message:
"## Kernel loading failed (missing x86 kernel setup) ..."
This change now removes this check and booting of FIT images works just
fine.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Stefan Roese [Thu, 30 Mar 2017 10:58:12 +0000 (12:58 +0200)]
binman: Remove hard-coded file name for x86 flash-descriptor & intel-me
Now that we have added file names from Kconfig in x86 u-boot.dtsi,
update binman to avoid using hard-coded names.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Stefan Roese [Thu, 30 Mar 2017 10:58:11 +0000 (12:58 +0200)]
x86: Add file names from Kconfig in descriptor/intel-me nodes in u-boot.dtsi
Since we now have the file names configurable via Kconfig for the flash
descriptor and intel-me files, add these from Kconfig in the corresponding
dts nodes.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Stefan Roese [Thu, 30 Mar 2017 10:58:10 +0000 (12:58 +0200)]
x86: Kconfig: Add options to configure the descriptor.bin / me.bin filenames
This introduces two Kconfig options to enable board specific filenames
for the Intel binary blobs to be used to generate the SPI flash image.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Mon, 6 Mar 2017 11:51:53 +0000 (13:51 +0200)]
x86: Remove unused option
There is option which is not used:
CONFIG_ZBOOT_32
Remove it from default x86 config and from whitelist.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andrew F. Davis [Fri, 7 Apr 2017 15:11:25 +0000 (10:11 -0500)]
defconfigs: am43xx_hs_evm: Add USB Host boot mode support
Enable SPL_USB_HOST_SUPPORT in the default defconfig to allow
booting from USB peripherals. Unlike the non-HS boards, we
already load SPL to a 0x4030_0000+ address, so no other changes
are needed.
Andrew F. Davis [Fri, 7 Apr 2017 15:11:19 +0000 (10:11 -0500)]
defconfigs: am335x_hs_evm: Sync HS and non-HS defconfigs
Sync new additions to non-HS defconfig with HS defconfig. Also add SPL
NAND support, this was disabled before due to size constraints, enable
this now at the expense of the less used GPT partition support.
Andrew F. Davis [Fri, 7 Apr 2017 19:29:36 +0000 (14:29 -0500)]
spl: net: Add FIT image support over network boot
FIT support in the net boot case is much like the RAM boot case in that
we load our image to "load_addr" and pass a dummy read function into
"spl_load_simple_fit()". As the load address is no longer hard-coded to
the final execution address, legacy image loading will require load_addr
to be set correctly in the image header.
TI K2E secure devices have to be built with TI_SECURE_DEVICE, FIT, and
FIT_IMAGE_POST_PROCESS enabled. Add a dedicated defconfig for this.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Kconfig: Adds SYS_TEXT_BASE config option for Keystone2
This patch makes SYS_TEXT_BASE a config option for Keystone2
so that it can be used to load u-boot at different addresses
on secure and non-secure Keystone2 devices.
Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
doc: Updates info on using Keystone2 secure devices
Add a section describing the secure boot image used on
Keystone2 secure devices.
Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Adds an additional image type needed for supporting secure keystone
devices. The build generates u-boot_HS_MLO which can be used to boot
from all media on secure keystone devices.
Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
arm: mach-omap2: Add secure image name common to OMAP and keystone
As K2 can directly boot U-Boot, add u-boot_HS_MLO as the secure image
name for secure K2 devices, for all boot modes other than SPI flash.
Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
arm: mach-omap2: Enable Kconfig support for K2 HS devices
Like the OMAP54xx, AM43xx, & AM33xx family SoCs, the keystone family
of SoCs also have high security enabled models. Allow K2E devices to
be built with HS Device Type Support.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
arm: mach-keystone: Implements FIT post-processing call for keystone SoCs
This commit implements the board_fit_image_post_process() function for
the keystone architecture. This function calls into the secure boot
monitor for secure authentication/decryption of the image. All needed
work is handled by the boot monitor and, depending on the keystone
platform, the security functions may be offloaded to other secure
processing elements in the SoC.
The boot monitor acts as the gateway to these secure functions and the
boot monitor for secure devices is available as part of the SECDEV
package for KS2. For more details refer doc/README.ti-secure
Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
image: Fixes build warning with CONFIG_FIT_IMAGE_POST_PROCESS
The function 'board_fit_image_post_process' is defined only when the
config option CONFIG_FIT_IMAGE_POST_PROCESS is enabled. For secure
systems that do not use SPL but do use FIT kernel images, only
CONFIG_FIT_IMAGE_POST_PROCESS will be defined, which will result in an
implicit declaration of function 'board_fit_image_post_process' warning
while building u-boot. Fix this warning.
Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Andrew F. Davis [Fri, 7 Apr 2017 14:55:20 +0000 (09:55 -0500)]
ti_armv7_common: env: Change FIT image name to match build name
The most common name for a FIT image containing a bootable kernel is
"fitImage", as our builds now use this name also, change this to the
default in our U-Boot environment.
mtd: nand: am335x_spl_bch: Incorporate tWB delay in nand_command function
Various commands to NAND flash results in the NAND flash becoming busy.
For those commands the SoC should wait until the NAND indicates it is
no longer busy before sending further commands. However, there is a delay
between the time the SoC sends its last command and when the NAND flash
sets its Ready/Busy Pin. This delay (tWB) must be respected or the SoC may
falsely assume the flash is ready when in reality it just hasn't had enough
time to indicate that it is busy.
Properly delaying by tWB is already done for nand_command/nand_command_lp
in nand_base.c including the version of it in the Linux kernel. Therefore,
this patch brings the handling of tWB delay inline to nand_base.c
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
[trini: Reformat comments slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
Lukasz Majewski [Mon, 27 Mar 2017 08:15:27 +0000 (10:15 +0200)]
ti: clocks: Fix do_enable_clocks() to accept NULL pointers as input parameters
Up till this commit passing NULL as input parameter was allowed, but not
handled properly.
When one passed NULL to one of this function parameters, the code was
executed causing data abort.
However, what is more interesting, the abort was not caught because of code
execution in HYP mode with masked CPSR A bit ("Imprecise Data Abort mask bit).
The TI's AM57xx SoC switch to HYP mode with A bit masked in lowlevel_init.S
due to SMC call. Such operation (by default) is performed in SoC ROM code.
The problem would pop up when one:
- Switch back to SVC mode after disabling LPAE support
- Somebody enables A bit (by executing cpsie a asm instruction)
and then the previously described exception would be caught.
Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
common/xyzModem.c: Do not use hard-coded address for debug buffer
Under the plethora of #ifdefs, the xyzModem code hid this pearl:
static char *zm_out = (char *) 0x00380000;
This was only enabled when DEBUG is defined, so it's probably why it
went unnoticed for so long. No idea what platform had memory at that
exact location, but the this approach is extremely hacky.
Use a static buffer instead.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
spl: Kconfig: SPL_MMC_SUPPORT depends on GENERIC_MMC
spl_mmc.c calls mmc_initialize(). This symbol is provided in
drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled.
The sunxi Kconfig case is an oddball because it redefines
SPL_MMC_SUPPORT.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
[trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig] Signed-off-by: Tom Rini <trini@konsulko.com>
common, kconfig: Fix defaut value of BOOTSTAGE_STASH_SIZE
The default value of BOOTSTAGE_STASH_SIZE should be set to hexadecimal,
but an integer value is set. This fixes the BOOTSTAGE_STASH_SIZE number
from hexadecimal to integer.
Vikas Manocha [Fri, 31 Mar 2017 23:34:39 +0000 (16:34 -0700)]
spl: armv7m: keep ARM v7M in thumb mode while jumping to entry point
On ARM v7M, the processor will return to ARM mode when executing blx
instruction with bit 0 of the address == 0. Always set it to 1 to stay
in thumb mode.
Similar commit: f99993c10882f7dc8ec35993d5febe59aac01e6a
Author: Matt Porter <mporter@konsulko.com>
Date: Tue May 5 15:00:23 2015 -0400
common/cmd_boot: keep ARM v7M in thumb mode during do_go_exec()
config: am335x_evm: detect BeagleBone Blue using BLA
BeagleBone Blue is next grenation of boards from BeagleBoard.org, focusing
on robotics with a TI wl1835 wireless module for connectivity.
This board can be indentified by the BLAx value after A335BNLT (BBB)
in the at24 eeprom:
BLAx: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 4c 41 30 |.U3.A335BNLTBLA2|]
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@konsulko.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Will Newton <willn@resin.io> Reviewed-by: Tom Rini <trini@konsulko.com>
config: am335x_evm: detect Green Wireless using GW1
SeeedStudio BeagleBone Green Wireless (BBGW) is an expansion of the
SeeedStudio Green (BBG) with the Ethernet replaced by a TI wl1835
wireless module.
This board can be indentified by the GW1x value after A335BNLT (BBB)
in the at24 eeprom:
GW1x [aa 55 33 ee 41 33 33 35 42 4e 4c 54 47 57 31 41 |.U3.A335BNLTGW1A|]
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: Stored in at24 eeprom at address 5-16:
hexdump -e '8/1 "%c"' /sys/bus/i2c/devices/0-0050/eeprom | cut -b 5-16
Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@konsulko.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Will Newton <willn@resin.io> Reviewed-by: Tom Rini <trini@konsulko.com>
config: am335x_evm: detect Black Wireless using BWA
BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with
the Ethernet replaced by a TI wl1835 wireless module.
This board can be indentified by the BWAx value after A335BNLT (BBB)
in the at24 eeprom:
BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@konsulko.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Will Newton <willn@resin.io> Reviewed-by: Tom Rini <trini@konsulko.com>
Joakim Tjernlund [Thu, 23 Mar 2017 17:02:41 +0000 (18:02 +0100)]
Remove extra fdt_fixup_ethernet() call
ft_cpu_setup() already calls fdt_fixup_ethernet(), calling it
in image_setup_libfdt() is both redundant and breaks any modifications
done by ft_board_setup(). Restore the old behavior by removing
the call in image_setup_libfdt()
Fixes: 13d06981a982 ("image: Add device tree setup to image library") Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Andrew F. Davis [Fri, 10 Mar 2017 21:53:54 +0000 (15:53 -0600)]
ti_armv7_common: env: Use args_mmc in FIT loading path
The env command 'args_fit' does not define a root path, this forces us to
embed the rootfs into the FIT image. FIT images do not need to contain a
rootfs, when they do not the kernel will fall-back to the kernel argument
'root', if this is not defined the kernel will not boot. It is safe to
add this as when we do have the rootfs in FIT this argument is ignored.
As 'loadfit' is only called from the MMC boot path, use 'args_mmc' to
correctly populate 'bootargs'.
Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
fuz@fuz.su [Tue, 7 Mar 2017 21:53:17 +0000 (22:53 +0100)]
Apparent conflict between CONFIG_BLK and CONFIG_API
Good evening,
I am trying to port FreeBSD to the ASUS Tinker Board, a computer based
on the Rockchip 3288 SoC. FreeBSD's boot loader (named loader(8)) needs
CONFIG_API to be enabled, but trying to build an U-Boot from trunk with
both CONFIG_API and CONFIG_BLK (as required for Rockchip SoC's?) leads
to the following build failure:
$ CROSS_COMPILE=arm-none-eabi- gmake tinker-rk3288_defconfig all
...
CC api/api_storage.o
api/api_storage.c: In function 'dev_read_stor':
api/api_storage.c:334:9: error: 'struct blk_desc' has no member named 'block_read'
if ((dd->block_read) == NULL) {
^~
api/api_storage.c:339:11: error: 'struct blk_desc' has no member named 'block_read'
return dd->block_read(dd, start, len, buf);
^~
api/api_storage.c:340:1: warning: control reaches end of non-void function [-Wreturn-type]
}
^
gmake[2]: *** [scripts/Makefile.build:281: api/api_storage.o] Fehler 1
gmake[1]: *** [Makefile:1229: api] Fehler 2
gmake: *** [Makefile:460: __build_one_by_one] Error 2
I applied the following fix, but the product doesn't boot. Perhaps
that's not a property of the fix though:
Sekhar Nori [Wed, 8 Feb 2017 13:13:59 +0000 (18:43 +0530)]
board: ti: am57xx: enable input on mmc clock
As per the latest pinmux data available for AM572x EVM,
rev A3, input should be enabled on MMC clock lines for
MMC2/2/3 for stable operation.
Further, AM572x TRM, SPRUHZ6, Revised June 2016, in
section 18.4.6.1.1 "Pad Configuration Registers" states
that input should be enabled for MMC 2/3/4 clock lines.
Enable input on MMC1 and MMC3 clock to match the latest
pinmux data. Input is already enabled on MMC2 clock for
BeagleBoard x15. Further, input is already enabled on all
MMCx clocks for other AM57xx boards (AM572x and AM571x
IDK).
Tested with HS and UHS SD card on AM572x EVM Rev A3.
Signed-off-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Vignesh R [Wed, 8 Mar 2017 08:28:17 +0000 (13:58 +0530)]
ARM: keystone: Pass SPI MTD partition table via kernel command line
SPI U-Boot image for K2 boards have now exceeded 512K partition
allocated to it and no longer fit the partitions defined in kernel DTS
file. Therefore, pass an updated MTD partition table from U-Boot as
kernel command line arguments to avoid kernel from accidentally
modifying boot loader image that has overflowed to next user partition.
To do is, introduce a common environment file for declaring SPI
partition so that each individual boards need not repeat the same.
Choose appropriate SPI bus from board config file and pass it as command
line argument to kernel.
Philipp Tomsich [Fri, 24 Mar 2017 18:08:55 +0000 (19:08 +0100)]
ARMv8: add GOT sections to the list of sections copied
Recent Linux distributions (e.g. Debian 9) include cross-compilers for
AArch64, but only for the aarch64-linux-gnu triplet only. It can thus
be expected that users will attempt to use the system cross-compiler
(instead of an aarch64-elf variant) to compile U-Boot for their ARMv8
target systems.
One key differences between an aarch64-linux-gnu and an aarch64-elf
compiler are the default settings regarding position-independent: with
the aarch64-linux-gnu compiler, the default will create and use the
global offset table.
This change-set adjusts the list of sections copied on ARMv8 to include
the GOT sections. With this added, the list matches the previous setup
for AArch32 closely.
Note that this is not an 'academic' issue, but was in fact encountered
by our QA during testing of the RK3399-Q7 BSP and resulted in an
early failure of the SPL stage during FDT setup.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
env_mmc: Allow SPL to use any MMC device to load/save the environment
SPL has been restricted to use only dev 0 based on the assumption that only
one MMC device is registered. This is not always the case and many
platforms now register several devices as expected by the spl mmc boot code
For those platform SPL_ENV_SUPPORT is broken if dev is forced to 0.
A word of warning: this commit may break SPL_ENV_SUPPORT on platforms that
do not register the same MMC controllers in SPL and in u-boot (mostly iMX6
based platforms). Fortunately none of those activate SPL_ENV_SUPPORT in
their default configuration.
Florent Jacquet [Thu, 16 Feb 2017 10:46:42 +0000 (11:46 +0100)]
sunxi: Add defconfig for Allwinner A23 EVB
This enables the support for the Allwinner A23 Evaluation Board (EVB),
that already had a device tree (from Linux) but no defconfig.
This board has an AXP223 PMIC, some NAND, Audio out and in plugs, an
accelerometer and light sensor, as well as a USB HSIC hub and a USB
OTG mini-USB connector. It also has a Wifi/BT chip.
Access to the other buses (LCD, MIPI DSI, LVDS, etc) can be done
through dedicated pin headers.
Signed-off-by: Florent Jacquet <florent.jacquet@free-electrons.com> Cc: Jagan Teki <jagan@openedev.com> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Mon, 20 Mar 2017 14:57:22 +0000 (15:57 +0100)]
sunxi: Add default environment size
On boards that defines ENV_IS_NOWHERE, such as the NES classic, commit 19dbe7d1a3f7 ("common: Move environment choice to Kconfig") broke the build
because of a missing environment size.
Reintroduce a default environment size consistent with what we had before.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
projects / u-boot.git / log