Ioana Ciornei [Wed, 15 Mar 2023 11:04:09 +0000 (13:04 +0200)]
arch: arm: dts: fsl-ls1088a.dtsi: add an 'soc' node
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Vladimir Oltean [Wed, 15 Mar 2023 11:01:16 +0000 (13:01 +0200)]
configs: convert NXP LS1028A RDB and QDS to DM_SERIAL
Since the device trees are more or less synchronized with Linux, the
only necessary changes are to enable CONFIG_DM_SERIAL and the DM_SERIAL
driver for ns16550 (ns16550.c rather than serial_ns16550.c).
ls1028aqds_tfa_lpuart_defconfig already uses DM_SERIAL for the LPUART
driver, so I didn't touch that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
The spl_board_prepare_for_boot() should be called before jump_to_image_no_args()
to perform board-specific deinitialization before jumping to the next stage.
This board-specific deinitialization can be very much anything, e.g. disable
dcache in case it was enabled, or such.
Add the missing spl_board_prepare_for_boot() call into f_sdp .
Sinthu Raja [Mon, 3 Apr 2023 17:03:12 +0000 (12:03 -0500)]
arm: dts: k3-j721e-sk-u-boot: fix boot on j721e SK
J721e SK has been broken since at least March 2022.
The main-navss and mcu-navss nodes were renamed and this caused the
A72 SPL to fail early in the boot even before the serial port was
enabled. Fix this.
A later patch series between v2022.07 and v2022.10 additionally broke
boot on this board by introducing hbmc nodes which are not present on
this board. The right fix is to disable these by default in the SOC
dtsi file, but for now we can also disable them in the u-boot dtsi.
With both these fixed, we can now boot the j721e SK board fully from
mainline u-boot.
Fabio Estevam [Wed, 15 Feb 2023 18:24:44 +0000 (15:24 -0300)]
pico-imx6: Pass the mmc alias to fix boot regression
Originally, the mmc aliases node was present in imx6qdl-pico.dtsi.
After the sync with Linux in commit d0399a46e7cd ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a boot regression in which the eMMC card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the eMMC (esdhc3) was
mapped to mmc0.
Fixes: d0399a46e7cd ("imx6dl/imx6qdl: synchronise device trees with linux") Signed-off-by: Fabio Estevam <festevam@denx.de>
Peter Hoyes [Tue, 21 Mar 2023 13:01:16 +0000 (13:01 +0000)]
fdt: Make fdt addr -q quieter
64597346 "fdt: Add -q option to fdt addr for distro_bootcmd" introduced
the -q option for fdt addr, which sets the current working fdt address
without printing any output.
baf41410 "fdt: Show a message when the working FDT changes" made the
utility function set_working_fdt_addr (in cmd/fdt.c) output a message
on each invocation, even if called via fdt addr -q, in which case its
output is now slightly noisier.
To fix this, split out set_working_fdt_addr into set_working_fdt_addr
plus the static function set_working_fdt_addr_quiet.
set_working_fdt_addr_quiet can be called by "quiet" fdt cmd logic and
set_working_fdt_addr is exported (as before) to other boot logic. The
latter calls the former.
Remove the assertion from the fdt addr test case when calling with the
-q argument.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com> Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
But the function pinctrl_gpio_get_pinctrl_and_offset can't handle this
case because the "index" argument passed to dev_read_phandle_with_args
is fixed to be "0". Use a loop to traverse the array to fix it.
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Marek Vasut [Sat, 11 Mar 2023 16:29:21 +0000 (17:29 +0100)]
cmd: fdt: Use env_set_hex() for "get addr" and "get size"
The 'fdt get addr' and 'env get size' is always assumed to be hex
value, drop the prefix, and outright switch to env_set_hex(). Since
this might break existing users who depend on the existing behavior
with 0x prefix, this is a separate patch.
Revert if this breaks anything.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
David Sebek [Thu, 30 Mar 2023 21:51:14 +0000 (17:51 -0400)]
rockchip: Fix incorrect constant name in RAM init code
A condition in the rk3399 RAM initialization code used the old
CONFIG_RAM_RK3399_LPDDR4 constant name. This commit changes the
condition to use the correct CONFIG_RAM_ROCKCHIP_LPDDR4 constant.
Roman Kopytin [Mon, 20 Mar 2023 03:28:13 +0000 (03:28 +0000)]
test_vboot.py: include test of fdt_add_pubkey tool
Add test_fdt_add_pubkey test which provides simple functionality test
which contains such steps:
create DTB and FIT files
add keys with fdt_add_pubkey to DTB
sign FIT image
check with fit_check_sign that keys properly added to DTB file
Signed-off-by: Roman Kopytin <Roman.Kopytin@kaspersky.com> Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com> Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Assigning the value of a variable to itself should be avoided.
Addresses-Coverity-ID: 451089 ("Evaluation order violation") Fixes: 180b7118bed8 ("efi_loader: fix device-path for USB devices") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
We use short device-paths in boot options so that a file on a block device
can be found independent of the port into which the device is plugged.
Usb() device-path nodes only contain port and interface information and
therefore cannot identify a block device.
UsbWwi() device-path nodes contain the serial number of USB devices.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Fixes: edca8cf72130 ("Convert CONFIG_SCSI_AHCI_PLAT et al to Kconfig") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Ensure that a freshly written fat file with a lower case filename which
fits into the upper case 8.3 short filename is not mangeled with a tilde
and number.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Svyatoslav Ryhel [Mon, 20 Mar 2023 19:06:30 +0000 (21:06 +0200)]
input: button_kbd: make driver complementary to gpio buttons
Remove need of dts binding for button keyboard since it reuses
gpio-keys binding. Select gpio-keys driver if button keyboard
is selected since button keyboard can not operate on its own.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30 Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Svyatoslav Ryhel [Mon, 20 Mar 2023 19:01:43 +0000 (21:01 +0200)]
cmd: ums: abort mounting by pressing any key
This patch introduses config which allows interrupt run of usb
mass storage with any key. This is especially useful on devices
with limited input capabilities like tablets and smatphones which
have only gpio keys in direct access.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Evgeny Bachinin [Mon, 20 Mar 2023 08:23:13 +0000 (11:23 +0300)]
test: fdt: fix run_commandf() warnings
Fix warnings both for 32bit and 64bit architecture after adding
printf-like attribute format for run_commandf():
warning: format ‘%x’ expects argument of type ‘unsigned int’, but
argument 2 has type ‘ulong {aka long unsigned int}’ [-Wformat=]
ret = run_commandf("fdt addr -c %08x", addr);
^ Signed-off-by: Evgeny Bachinin <EABachinin@sberdevices.ru> Cc: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Fixup testcases added since patch was posted] Signed-off-by: Tom Rini <trini@konsulko.com>
Evgeny Bachinin [Mon, 20 Mar 2023 08:23:11 +0000 (11:23 +0300)]
cli: run_commandf(): small fixups
* vsnprintf() can truncate cmd, hence it makes no sense to launch such
command (it's broken). Moreover, it's better to signalize to the caller
about such case (for facilitating debugging or bug hunting).
* Fix kernel-doc warnings:
include/command.h:264: info: Scanning doc for run_commandf
include/command.h:268: warning: contents before sections
include/command.h:271: warning: No description found for return value
of 'run_commandf'
* Add printf-like format attribute to validate at compile-time the format
string against parameters's type.
* Fix compilation error in case of -Wall, -Werror, -Wextra:
error: variable ‘i’ set but not used [-Werror=unused-but-set-variable]
* Drop extra ret variable.
Signed-off-by: Evgeny Bachinin <EABachinin@sberdevices.ru> Reviewed-by: Simon Glass <sjg@chromium.org>
Chris Packham [Sun, 19 Mar 2023 21:23:44 +0000 (10:23 +1300)]
drivers: rtc: add max313xx series rtc driver
Adding support for Analog Devices MAX313XX series RTCs.
This is ported from the Linux driver and adapted for use in u-boot.
Notable differences are
- handling of tm_year and tm_mon differ
- clock source support is omitted
- hwmon support for the MAX31328 and MAX31343 is omitted
- rtc_ops->reset is added
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Chris Packham [Sun, 19 Mar 2023 21:23:43 +0000 (10:23 +1300)]
include: kernel.h: port find_closest() from Linux
The find_closest() macro can be used to find an element in a sorted
array that is closest to an input value. Bring in this macro from
Linux v6.3-rc1-2-g8ca09d5fa354.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Rasmus Villemoes [Fri, 17 Mar 2023 20:12:22 +0000 (21:12 +0100)]
gpio: allow passing NULL to gpio_request_by_line_name() to search all gpio controllers
The API is more convenient to use if one doesn't have to know upfront
which gpio controller has a line with the name one is searching for,
and arrange to look that device up somehow. Or implement this loop
oneself.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Simon Glass <sjg@chromium.org>
fs: ext4: fix files seen as symlink during deletion
The deletion process handles special case for symlinks whose target are
small enough that it fits in struct ext2_inode.b.symlink. So no block had
been allocated. But the check of file type wrongly considered regular
files as symlink. So, no block was freed. So, the EXT4 partition could be
corrupted because of no free block available.
Do not mangle lower or mixed case filenames which fit into the upper
case 8.3 short filename. This ensures FAT standard compatible short
filenames (SFN) to support systems without long filename (LFN) support
like boot roms (ex. SFN BOOT.BIN instead of BOOT~1.BIN for LFN
boot.bin).
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Stephen Carlson [Fri, 10 Mar 2023 19:07:15 +0000 (11:07 -0800)]
test: Add test for new command pci_mps
Adds a test for the new pci_mps command to ensure that it can set the
Maximum Payload Size (MPS) of all devices to 256 bytes in the sandbox
environment. Enables the pci_mps command in the sandbox environment so
that this test can be run.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Stephen Carlson [Fri, 10 Mar 2023 19:07:13 +0000 (11:07 -0800)]
cmd: pci: Add command to set MPS of all PCIe devices
Enable tuning of the PCI Express MPS (Maximum Payload Size) of
each device. The Maximum Read Request Size is not altered.
The SAFE method uses the largest MPS value supported by all devices in the
system for each device. This method is the same algorithm as used by Linux
pci=pcie_bus_safe.
The PEER2PEER method sets all devices to the minimal (128 byte) MPS, which
allows hot plug of devices later that might only support the minimum size,
and ensures compatibility of DMA between two devices on the bus.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Rasmus Villemoes [Fri, 10 Mar 2023 10:58:03 +0000 (11:58 +0100)]
sysinfo: gpio: fix loop over DT "revisions" array
There can certainly be a lot more elements in the "revisions" (and
"names") arrays than there are gpios used to form the trinary number
we're searching for; we simply don't know the array size up-front.
Nor do we need to, because the loop body already knows to recognize
-EOVERFLOW as "not that many elements present" (and we have a test
that specifically ensures that dev_read_u32_index() returns exactly
that). So just drop the i < priv->gpio_num condition.
While in here, fix the weird placement of the default: keyword.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Instead of calling env_get(from) up to three times, just do it once,
computing the value we will put into 'to' and error out if that is
NULL (i.e. no 'from' variable and no default provided).
No functional change.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Mon, 27 Feb 2023 19:56:31 +0000 (20:56 +0100)]
image: Fix potentially uninitialized data variable
In case fitImage support is disabled, and image_locate_script() is
passed a fitImage, then the 'data' variable is used uninitialized.
Drop into the default: branch of the switch-case statement and do
not return the uninitialized data, and do not modify the return
pointer either, just print an error message.
Reported by clang build:
"
$ make HOSTCC=clang CC=clang KCFLAGS=-Werror sandbox64_defconfig && make HOSTCC=clang CC=clang KCFLAGS=-Werror
...
boot/image-board.c:1006:7: error: variable 'data' is used uninitialized whenever switch case is taken [-Werror,-Wsometimes-uninitialized]
case IMAGE_FORMAT_LEGACY:
^~~~~~~~~~~~~~~~~~~
include/image.h:608:29: note: expanded from macro 'IMAGE_FORMAT_LEGACY'
^~~~
boot/image-board.c:1128:19: note: uninitialized use occurs here
*datap = (char *)data;
^~~~
boot/image-board.c:1001:11: note: initialize the variable 'data' to silence this warning
u32 *data;
^
= NULL
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Mon, 6 Mar 2023 14:53:54 +0000 (15:53 +0100)]
arm64: imx8mm: imx8mn: imx8mp: Drop FEC GPR[1] board workaround
The FEC interface mode is now configured in common board_interface_eth_init()
and called by FEC MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Marek Vasut [Mon, 6 Mar 2023 14:53:53 +0000 (15:53 +0100)]
arm64: imx8mp: Drop EQoS GPR[1] board workaround
The EQoS interface mode is now configured in common board_interface_eth_init()
and called by EQoS MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Marek Vasut [Mon, 6 Mar 2023 14:53:52 +0000 (15:53 +0100)]
arm64: dts: imx8mp: Drop EQoS clock workaround
The assigned-clock no longer have to be dropped, the clock are now
defined in clk-imx8mp.c and used by DWMAC driver to configure the
DWMAC clock. Drop the workarounds from U-Boot specific DT extras.
Emanuele Ghidoli [Thu, 16 Feb 2023 11:31:15 +0000 (12:31 +0100)]
configs: verdin-imx8mp: Fix wrong early malloc() heap size
Set, previously unset, CONFIG_SPL_SYS_MALLOC_F_LEN to 0x4000 whose
default value is 0x10000.
Early malloc() uses CRAM_S at 0x184000 (CFG_MALLOC_F_ADDR), this ram
area end at 0x188000.
Rasmus Villemoes [Wed, 22 Mar 2023 14:42:05 +0000 (15:42 +0100)]
ARM: imx: imx8mp: fix enable_i2c_clk
In order for i2c_num==4 and 5 to stay invalid for non-imx8mp SOCs, the
i2c_ccgr[] array must be sized by the number of initializers present,
not with a hard-coded 6 which would implicitly initialize the last two
elements with zeroes.
Also, the bounds check is off-by-one.
Fixes: c92c3a4453b8 "ARM: imx: imx8mp: Enable support for i2c5 and i2c6 on i.MX8MP" Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Marek Vasut [Mon, 6 Mar 2023 14:53:51 +0000 (15:53 +0100)]
net: fec_mxc: Add board_interface_eth_init() for i.MX8M Mini/Nano/Plus
Implement common board_interface_eth_init() and call it from the FEC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Mini/Nano/Plus FEC and supersedes the current board-side
configuration of the same IOMUX GPR[1] duplicated in the board files.
Marek Vasut [Mon, 6 Mar 2023 14:53:50 +0000 (15:53 +0100)]
net: fec_mxc: Add ref clock setup support for i.MX8M Mini/Nano/Plus
The FEC ref clock frequency on i.MX8M Mini/Nano/Plus was so far configured
via ad-hoc board code. Replace that with DM clock clk_set_rate() instead.
This way, the driver claims all its required clock and sets the ref clock
rate, without any need of architecture specific register fiddling.
Marek Vasut [Mon, 6 Mar 2023 14:53:49 +0000 (15:53 +0100)]
net: dwc_eth_qos: Add board_interface_eth_init() for i.MX8M Plus
Implement common board_interface_eth_init() and call it from the DWMAC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Plus DWMAC and supersedes current board-side configuration
of the same IOMUX GPR[1] duplicated in the board files.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 6 Mar 2023 14:53:48 +0000 (15:53 +0100)]
net: dwc_eth_qos: Add i.MX8M Plus RMII support
With DM clock support in place, it is easy to add RMII support into the
MAC driver. The RMII cannot operate at 1000 Mbps and at 100 and 10 Mbps
the clock frequency is 50 MHz and 5 MHz instead of 25 MHz and 2.5 MHz.
The board DT requires the following adjustments to EQoS node:
phy-mode = "rmii";
assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>,
<&clk IMX8MP_SYS_PLL2_100M>,
<&clk IMX8MP_SYS_PLL2_50M>;
assigned-clock-rates = <0>, <100000000>, <50000000>;
Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 6 Mar 2023 14:53:47 +0000 (15:53 +0100)]
net: dwc_eth_qos: Add DM CLK support for i.MX8M Plus
The DWMAC clock in i.MX8M Plus were so far configured via ad-hoc
architecture code. Replace that with DM clock instead. This way,
the driver claims all its required clock, enables and disables
them, and even gets the CSR clock rate and sets the TX clock rate,
without any need of architecture specific register fiddling. Drop
the architecture specific code while at it too.
The adjustment here is modeled after STM32MP15xx clock handling
in this driver.
Marek Vasut [Mon, 6 Mar 2023 14:53:46 +0000 (15:53 +0100)]
net: dwc_eth_qos: Set DMA_MODE SWR bit to reset the MAC
The driver currently only waits for DMA_MODE SWR bit to clear itself.
This is insufficient e.g. on i.MX8M Plus, where the MAC must be reset
before IOMUX GPR[1] content is latched into the MAC and used. Without
the proper reset, the i.MX8M Plus MAC variant does not take the value
in IOMUX GPR[1] into account, which makes it impossible e.g. to switch
interface mode from RGMII to any other.
Since proper reset is desired in general to put the block into defined
state, always assert the DMA_MODE SWR bit before waiting for the bit
to clear itself.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 6 Mar 2023 14:53:44 +0000 (15:53 +0100)]
net: dwc_eth_qos: Drop unused dm_gpio_free() on STM32
The dm_gpio_free() is never called, because for stm32, the phy_reset_gpio
pointer is never valid. This is because only tegra186 ever claims the
phy_reset_gpio, all other platforms use the PHY framework to reset the
PHY instead. Drop the dm_gpio_free() and dm_gpio_is_valid().
Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Marek Vasut <marex@denx.de>
Marcel Ziswiler [Fri, 3 Mar 2023 13:26:37 +0000 (14:26 +0100)]
colibri-imx8x: update env memory layout
Update the distro config env memory layout for the Colibri iMX8X:
- kernel_comp_addr_r=0xb0000000 temporary area for uncompressing (ie FIT
images or Image.gz booted using booti)
- kernel_comp_size=0x08000000
- loadaddr=0x95400000 avoiding any reserved areas located before that
- fdt_addr_r = loadaddr + 128MB - allows for 128MB kernel
- scriptaddr = fdt_addr_r + 512KB - allows for 512KB fdt
- ramdisk_addr_r = scriptaddr + 512KB - allows for 512KB script
Idea of memory layout taken from commit a9f1e35bedc4
("apalis-imx8: update env memory layout").
Note that for our regular BSP Layers and Reference Images for Yocto
Project an updated distro boot script is required (see
meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Marek Vasut [Thu, 2 Mar 2023 22:40:44 +0000 (23:40 +0100)]
ARM: dts: imx: Add support for DH electronics i.MX8M Plus DHCOM on PDK3
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK3 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
projects / u-boot.git / log