Clean up the i.MX5 clock driver:
- Use readl() and writel() instead of their __raw_ counterparts.
- Use the clr/setbits_le32() family of macros rather than expanding code.
- Use accessor macros for bit-fields instead of _MASK and _OFFSET.
mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input
mx6qsabresd is a board based on mx6q SoC with the following features:
- 1GB of DDR3
- 1 USB OTG port
- 1 HDMI output port
- SPI NOR
- LVDS panel
- Gigabit Ethernet
- Camera Connector
- eMMC and SD card slot
- Audio
Lucas Stach [Sat, 29 Sep 2012 10:02:08 +0000 (10:02 +0000)]
tegra: clean up board include hell
The prototypes used in board files were all scattered out, which lead to
code duplication between SPL and normal U-Boot and some prototypes not actually
being used. Consolidate this in a common board header.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Lucas Stach [Tue, 25 Sep 2012 20:21:14 +0000 (20:21 +0000)]
tegra20: rework UART GPIO handling
Rename board provided gpio_config_uart() to
gpio_early_init_uart() as it does the same thing as the equally
called function provided by the uart-switch code. This allows
to simply call this function in early board init whether or not
we are building with CONFIG_UART_SWITCH defined.
Also provide a weak symbol for this function, to avoid the
need to provide this function for boards that don't need any
fixup.
This patch supersedes the earlier posted
"tegra: convert gpio_config_uart to weak symbol".
Build tested with MAKEALL -s tegra20
Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Lucas Stach [Tue, 25 Sep 2012 20:21:13 +0000 (20:21 +0000)]
tegra20: add clock_set_pllout function
Common practice on Tegra 2 boards is to use the pllp_out4 FO
to generate the ULPI reference clock. For this to work we have
to override the default hardware generated output divider.
This function adds a clean way to do so.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
Lucas Stach [Tue, 25 Sep 2012 09:59:12 +0000 (09:59 +0000)]
tegra20: complete periph_id enum
Most Tegra boards output the ULPI reference clock on pad DEV2.
Complete the periph_id enum so that we are able to enable this
clock output circuit.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Tom Warren [Wed, 19 Sep 2012 22:50:56 +0000 (15:50 -0700)]
Tegra20: Move some include files to arch-tegra for sharing with Tegra30
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.
All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.
Tom Warren [Wed, 19 Sep 2012 21:08:52 +0000 (14:08 -0700)]
Tegra20: Move some code files to common directories for upcoming Tegra30 patches.
Move files that are going to be common between T20 and T30 into 'tegra-common'
subdirs in AVP (arm720t), CPU (armv7), and shared (arch/arm/cpu/.) areas. Any
files that are left behind in '/tegra20' will be copied to '/tegra30' subdirs
and modified for that SoC. The 'common' files should need only minor changes.
Include files (arch/arm/include/asm/arch-tegra/tegra20) will be done in a
follow-on patch.
Builds fine w/MAKEALL -s tegra20. Checkpatch.pl is clean.
Medcom is the marketing name for an older, PXA-based version of the same
device. In order to avoid confusion, rename the Tegra-based version to
the new marketing name.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Joe Hershberger [Wed, 3 Oct 2012 09:38:47 +0000 (09:38 +0000)]
tools/env: Remove unneeded complexity
The length included the name length, and then it was subtracted back
out on each use. Now we don't include it in the first place. Also
realloc as we process arguments and eliminate memset. Use memcpy
instead of manually copying each byte.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Before this patch, there was a hard-coded env that was used as default
if the env in flash is detected as invalid. Now this tool (compiled
for a given board) will share the default env with the u-boot for the
board.
Fix include of config.h
Need to define "TEXT_BASE" when building the fw_env tool so that the
default env will be correct for environments which use it.
Define __ASSEMBLY__ when calling #include <config.h> so that we only
get #defines (all we're interested in).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
common: cmd_bdinfo: fix type of value in print_lnum
This fixes a warning when compiling with ELDK-5.2.1 for MIPS64:
cmd_bdinfo.c: In function 'print_lnum':
cmd_bdinfo.c:56:2: warning: format '%llX' expects argument of type 'long long unsigned int', but argument 3 has type 'u64' [-Wformat]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Simon Glass [Thu, 27 Sep 2012 15:33:46 +0000 (15:33 +0000)]
patman: Handle checkpatch.pl not providing file/line info
Sometimes we don't get a valid filename or line number from checkpatch.pl,
for example if the patch is in a bad format. Deal with this by using a
default value, rather than a stack trace.
Simon Glass [Thu, 27 Sep 2012 15:06:02 +0000 (15:06 +0000)]
patman: Support Series-name tag to name a series
Sometimes it is possible to forget the name of the branch you used to
generate an upstream series. To assist with this, add an optional
patman does not use this.
Kim Phillips [Fri, 21 Sep 2012 12:28:17 +0000 (12:28 +0000)]
add check infrastructure, default sparse
Add support for running source code checkers on u-boot source, e.g.,
using sparse to aid with typechecking. This comes in especially
handy as SoC vendors mix and match cores and devices with different
endianness, thus here we add CHECK_ENDIAN to the otherwise linux
kernel default CHECKFLAGS.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Pavel Herrmann [Thu, 27 Sep 2012 23:18:04 +0000 (23:18 +0000)]
sata.h: Make all sata/ata drivers include <sata.h>
- block_dev_desc_t says that block_(read|write) take lbaint_t for blkcnt
not ulong.
- We also move the extern of sata_dev_desc into <sata.h>
- Remove now duplicate declarations from driver-specific headers.
Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Tom Rini [Sat, 29 Sep 2012 14:55:11 +0000 (07:55 -0700)]
fsl_sata: Make sata_{read,write}() comply with <part.h>
- sata_write() takes a const void as the last argument. Fixing this
means we also need to make ata_low_level_rw_lba{28,48} also take a
const void.
- Both sata_{read,write} take lbaint_t for blkcnt and ulong for blknr
Lukasz Dalek [Tue, 2 Oct 2012 15:04:29 +0000 (17:04 +0200)]
usbether: Fixed bug when using with PXA25X chips
PXA25X chips don't support alternate settings so driver uses non-CDC
driver.
But only code defined between DEV_CONFIG_CDC signals that network is up.
This patch is fixing this bug by signaling that network is up after USB
SET_INTERFACE request.
Lucas Stach [Sun, 30 Sep 2012 22:44:35 +0000 (00:44 +0200)]
tegra20: add USB ULPI init code
This adds the required code to set up a ULPI USB port. It is
mostly a port of the Linux ULPI setup code with some tweaks
added for more correctness, discovered along the way of
debugging this.
To use this both CONFIG_USB_ULPI and CONFIG_USB_ULPI_VIEWPORT
have to be set in the board configuration file.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Lucas Stach [Tue, 25 Sep 2012 22:14:35 +0000 (00:14 +0200)]
usb: ehci: rework to take advantage of new lowlevel interface
Kill off ehci-core.h
It was used to specify some static controller data. To support more than
one controller being active at any time we have to carry the controller
data ourselfes. Change the ehci interface accordingly.
NOTE: OMAP implemented the ehci stuff a bit backwards and should be fixed
to do the same thing as other platforms. But the change for now is at least
compile clean.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Reviewed-by: Marek Vasut <marex@denx.de>
Igor Grinberg [Fri, 28 Sep 2012 10:04:46 +0000 (12:04 +0200)]
pmc405de and zeus: remove the env_ptr externs
The env_ptr is already declared in environment.h, so there is no need to
redeclare in board files (especially after including the environment.h)
Remove those declarations.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Stefan Roese [Wed, 19 Sep 2012 12:33:52 +0000 (14:33 +0200)]
ppc4xx: Remove IOP480 support
Since the IOP480 (PPC401/3 variant from PLX) is only used on 2
boards that are not actively maintained, lets remove support
for it completely. This way the ppc4xx code will get a bit cleaner.
Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu> Acked-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sun, 16 Sep 2012 16:54:22 +0000 (18:54 +0200)]
serial: Enhance the manual relocation
Enhance the manual relocation of drivers operations structure by
checking if the entries are NULL and increment them only if they
are not. This allows for setting any entry to NULL and it will
survive the manual relocation.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
Marek Vasut [Fri, 14 Sep 2012 21:46:48 +0000 (23:46 +0200)]
serial: Compile drivers/serial/serial.c by default
Compile drivers/serial/serial.c by default both into SPL and into
non-SPL builds, since CONFIG_SERIAL_MULTI is now the default state.
Also having common/serial.c in by default now, it's pointless to keep
-DCONFIG_SERIAL_MULTI in CPPFLAGS any longer, so remove it as well.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
Marek Vasut [Fri, 14 Sep 2012 21:45:51 +0000 (23:45 +0200)]
serial: Remove CONFIG_SERIAL_MULTI from remaining sources
Remove the parts depending either on disabled CONFIG_SERIAL_MULTI
or ifdefs around CONFIG_SERIAL_MULTI parts since CONFIG_SERIAL_MULTI
is now enabled by default.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
Marek Vasut [Fri, 14 Sep 2012 21:44:09 +0000 (23:44 +0200)]
serial: Remove CONFIG_SERIAL_MULTI from serial drivers
Remove the support for not-CONFIG_SERIAL_MULTI part from serial
port drivers and some board files. Since CONFIG_SERIAL_MULTI is
now enabled by default, that part is a dead code. Remove it.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
Marek Vasut [Fri, 14 Sep 2012 21:39:52 +0000 (23:39 +0200)]
serial: Remove CONFIG_SERIAL_MULTI from config files
Remove any notion of CONFIG_SERIAL_MULTI from board config files.
Since CONFIG_SERIAL_MULTI is now enabled by default, it is useless
to specify this config option in the board config files. Therefore
remove it.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
Enable CONFIG_SERIAL_MULTI for all builds of U-Boot. That includes
both SPL builds and non-SPL builds, everything. To avoid poluting
this patch with removal of ifdef-endif constructions containing
CONFIG_SERIAL_MULTI, the CONFIG_SERIAL_MULTI is temporarily added
into CPPFLAGS in config.mk . This will be again removed in following
patch.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
Marek Vasut [Sat, 29 Sep 2012 16:16:28 +0000 (18:16 +0200)]
serial: Move common/serial.c to drivers/serial/
Move the common/serial.c into driver/serial/, since this file
provides serial multiplexing functions and it is imperative to
be linked with libserial.o instead of libcommon.o.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
Marek Vasut [Sat, 29 Sep 2012 16:12:47 +0000 (18:12 +0200)]
serial: ns16550: Rename serial.c to serial_ns16550.c
This serial driver had wrong name of the source file for some time
now. The name of the driver was serial.c instead of any more logical
and fitting name. Thus, rename the driver source file to serial_ns16550.c
and be done with it.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Michal Simek <monstr@monstr.eu>
Marek Vasut [Sat, 15 Sep 2012 08:25:19 +0000 (10:25 +0200)]
serial: ns16550: Call usbtty_poll only in non-SPL build
Having both USBTTY and CONFIG_SERIAL_MULTI enabled in SPL, the
usbtty.c file is protected in Makefile to not be compiled into
the SPL. Yet, the ns16550 serial driver does not contain such
protection. Add it to avoid missing symbol error.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
Marek Vasut [Sat, 15 Sep 2012 08:33:51 +0000 (10:33 +0200)]
serial: Use puts() and hang() instead of panic() in SPL
If case the get_current() call fails before relocation, the U-Boot
must try to print an error message, fail and either reset or halt.
Such error is critical enough to halt the system, as it means the
system is in very bad state.
This is now also used in SPL, since CONFIG_SERIAL_MULTI is enabled
unconditionally. To avoid compiling whole vsprintf.c into SPL, use
puts() to print error message and hang() to stop the system in case
of SPL build.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
Marek Vasut [Fri, 14 Sep 2012 21:18:08 +0000 (23:18 +0200)]
serial: mxs: spl: Remove empty serial_* functions from SPL code
Remove the empty bodies from serial_* functions from MXS SPL code.
These empty implementations are now in common/serial.c instead so
declaring them also in the SPL code would cause a colision once
serial multi is enabled unconditionally.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 14 Sep 2012 20:40:08 +0000 (22:40 +0200)]
serial: sh: Implement CONFIG_SERIAL_MULTI into sh serial driver
Implement support for CONFIG_SERIAL_MULTI into sh serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sh driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Phil Edworthy <PHIL.EDWORTHY@renesas.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Tom Rini <trini@ti.com>
Marek Vasut [Fri, 14 Sep 2012 20:39:44 +0000 (22:39 +0200)]
serial: arm: Implement CONFIG_SERIAL_MULTI into sa1100 serial driver
Implement support for CONFIG_SERIAL_MULTI into sa1100 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sa1100 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
Marek Vasut [Fri, 14 Sep 2012 20:39:19 +0000 (22:39 +0200)]
serial: arm: Implement CONFIG_SERIAL_MULTI into s3c44b0 serial driver
Implement support for CONFIG_SERIAL_MULTI into s3c44b0 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c44b0 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
Marek Vasut [Fri, 14 Sep 2012 20:38:46 +0000 (22:38 +0200)]
serial: arm: Implement CONFIG_SERIAL_MULTI into pl01x serial driver
Implement support for CONFIG_SERIAL_MULTI into pl01x serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the pl01x driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Mathieu J. Poirier <mathieu.poirier@linaro.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: John Rigby <john.rigby@linaro.org> Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Marek Vasut [Fri, 14 Sep 2012 20:38:09 +0000 (22:38 +0200)]
serial: arm: Implement CONFIG_SERIAL_MULTI into netarm serial driver
Implement support for CONFIG_SERIAL_MULTI into netarm serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the netarm driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 14 Sep 2012 20:37:43 +0000 (22:37 +0200)]
serial: arm: Implement CONFIG_SERIAL_MULTI into mxc serial driver
Implement support for CONFIG_SERIAL_MULTI into mxc serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mxc driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 14 Sep 2012 20:37:17 +0000 (22:37 +0200)]
serial: Implement CONFIG_SERIAL_MULTI into max3100 serial driver
Implement support for CONFIG_SERIAL_MULTI into max3100 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the max3100 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
Marek Vasut [Fri, 14 Sep 2012 20:36:50 +0000 (22:36 +0200)]
serial: arm: Implement CONFIG_SERIAL_MULTI into lpc2292 serial driver
Implement support for CONFIG_SERIAL_MULTI into lpc2292 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the lpc2292 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
Marek Vasut [Fri, 14 Sep 2012 20:36:27 +0000 (22:36 +0200)]
serial: arm: Implement CONFIG_SERIAL_MULTI into lh7a40x serial driver
Implement support for CONFIG_SERIAL_MULTI into lh7a40x serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the lh7a40x driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
Marek Vasut [Fri, 14 Sep 2012 20:35:43 +0000 (22:35 +0200)]
serial: arm: Implement CONFIG_SERIAL_MULTI into ks8695 serial driver
Implement support for CONFIG_SERIAL_MULTI into ks8695 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ks8695 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
Marek Vasut [Fri, 14 Sep 2012 20:35:14 +0000 (22:35 +0200)]
serial: arm: Implement CONFIG_SERIAL_MULTI into ixp serial driver
Implement support for CONFIG_SERIAL_MULTI into ixp serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ixp driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Michael Schwingen <michael@schwingen.org>
Marek Vasut [Fri, 14 Sep 2012 20:34:51 +0000 (22:34 +0200)]
serial: arm: Implement CONFIG_SERIAL_MULTI into imx serial driver
Implement support for CONFIG_SERIAL_MULTI into imx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the imx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 14 Sep 2012 20:34:22 +0000 (22:34 +0200)]
serial: arm: Implement CONFIG_SERIAL_MULTI into clps7111 serial driver
Implement support for CONFIG_SERIAL_MULTI into clps7111 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the clps7111 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
Marek Vasut [Fri, 14 Sep 2012 20:33:21 +0000 (22:33 +0200)]
serial: sandbox: Implement CONFIG_SERIAL_MULTI into sandbox serial driver
Implement support for CONFIG_SERIAL_MULTI into sandbox serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sandbox driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Thu, 13 Sep 2012 14:53:49 +0000 (16:53 +0200)]
serial: arm: Implement CONFIG_SERIAL_MULTI into s3c64xx serial driver
Implement support for CONFIG_SERIAL_MULTI into s3c64xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c64xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: John Rigby <john.rigby@linaro.org> Cc: Minkyu Kang <mk7.kang@samsung.com>
Marek Vasut [Thu, 13 Sep 2012 14:53:15 +0000 (16:53 +0200)]
serial: arm: Implement CONFIG_SERIAL_MULTI into s3c4510b serial driver
Implement support for CONFIG_SERIAL_MULTI into s3c4510b serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c4510b driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
Marek Vasut [Thu, 13 Sep 2012 14:52:38 +0000 (16:52 +0200)]
serial: oc: Implement CONFIG_SERIAL_MULTI into OpenCores serial driver
Implement support for CONFIG_SERIAL_MULTI into OpenCores serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the OpenCores driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Scott McNutt <smcnutt@psyent.com>
Marek Vasut [Thu, 13 Sep 2012 14:52:07 +0000 (16:52 +0200)]
serial: Implement CONFIG_SERIAL_MULTI into ns9750 serial driver
Implement support for CONFIG_SERIAL_MULTI into ns9750 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ns9750 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
projects / u-boot.git / log