Simon Glass [Mon, 11 Mar 2013 06:08:06 +0000 (06:08 +0000)]
sf: Respect maximum SPI write size
Some SPI flash controllers (e.g. Intel ICH) have a limit on the number of
bytes that can be in a write transaction. Support this by breaking the
writes into multiple transactions.
Simon Glass [Mon, 11 Mar 2013 06:08:05 +0000 (06:08 +0000)]
spi: Add parameter for maximum write size
Some SPI controllers (e.g. Intel ICH) have a limit on the number of SPI
bytes that can be written at a time. Add this as a parameter so that
clients of the SPI interface can respect this value.
Simon Glass [Tue, 19 Mar 2013 04:58:56 +0000 (04:58 +0000)]
x86: spi: Add Intel ICH driver
This supports Intel ICH7/9. The Intel controller is a little unusual in
that it is mostly intended for use with SPI flash, and has some
optimisations and features specifically for that application. In
particular it is not possible to support ongoing transactions that
continue over many calls with SPI_XFER_BEGIN and SPI_XFER_END.
This driver supports writes of up to 64 bytes at a time, the limit
for the controller. Future work will improve this.
Signed-off-by: Bernie Thompson <bhthompson@chromium.org> Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Signed-off-by: Bill Richardson <wfrichar@chromium.org> Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Signed-off-by: Gabe Black <gabeblack@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 11 Mar 2013 06:08:03 +0000 (06:08 +0000)]
sf: Use spi_flash_alloc() in each SPI flash driver
Rather than each device having its own way to allocate a SPI flash
structure, use the new allocation function everywhere. This will make it
easier to extend the interface without breaking devices.
Simon Glass [Mon, 11 Mar 2013 06:08:02 +0000 (06:08 +0000)]
sf: Add spi_flash_alloc() to create a new SPI flash struct
At present it is difficult to extend the SPI flash structure since
all devices allocate it themselves, and few of them zero all fields.
Add a new function spi_flash_alloc() which can be used by SPI devices
to perform this allocation, and thus ensure that all devices can
better cope with SPI structure changes.
Simon Glass [Mon, 18 Mar 2013 19:23:40 +0000 (19:23 +0000)]
spi: Use spi_alloc_slave() in each SPI driver
Rather than each driver having its own way to allocate a SPI slave,
use the new allocation function everywhere. This will make it easier
to extend the interface without breaking drivers.
Simon Glass [Mon, 11 Mar 2013 06:08:00 +0000 (06:08 +0000)]
spi: Add function to allocate a new SPI slave
At present it is difficult to extend the SPI structure since all
drivers allocate it themselves, and few of them zero all fields. Add
a new function spi_alloc_slave() which can be used by SPI drivers
to perform this allocation, and thus ensure that all drivers can
better cope with SPI structure changes.
Tom Rini [Mon, 18 Mar 2013 16:31:00 +0000 (12:31 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.
Simon Glass [Tue, 5 Mar 2013 14:40:04 +0000 (14:40 +0000)]
sparc: Fix build warnings in serial.c
These macros are already defined in io.h so should not be declared in
serial.c.
serial.c:38:0: warning: "READ_BYTE" redefined
/home/sjg/c/src/third_party/u-boot/files/include/asm/io.h:36:0: note: this is the location of the previous definition
serial.c:39:0: warning: "READ_HWORD" redefined
/home/sjg/c/src/third_party/u-boot/files/include/asm/io.h:37:0: note: this is the location of the previous definition
serial.c:40:0: warning: "READ_WORD" redefined
/home/sjg/c/src/third_party/u-boot/files/include/asm/io.h:38:0: note: this is the location of the previous definition
serial.c:41:0: warning: "READ_DWORD" redefined
/home/sjg/c/src/third_party/u-boot/files/include/asm/io.h:39:0: note: this is the location of the previous definition
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 5 Mar 2013 14:40:03 +0000 (14:40 +0000)]
sparc: Fix out-of-tree building
It isn't clear why the sparc cpu Makefile has its own compile line, but
it does not work correctly with an out-of-tree build. Removing it fixes
this problem. Perhaps it does not introduce others.
Simon Glass [Tue, 5 Mar 2013 14:39:52 +0000 (14:39 +0000)]
x86: Adjust board_f.c for x86
For x86, things have adjusted somewhat since this series was originally
written. It has its own way of running through initcalls which is actually
nicer than others archs.
Unfortunately this does introduce exceptions. We will soon require use of
generic board on x86, but until then we need to fit in with what is there,
and treat x86 as a special case.
Simon Glass [Mon, 11 Mar 2013 07:06:48 +0000 (07:06 +0000)]
Add CONFIG_SYS_SYM_OFFSETS to support offset symbols
Link symbols as created by the link script can either be absolute or
relative to the text start. This option switches between the two options
so that we can support both.
As we convert architectures over to generic board, we can see if this
option is actually needed, or whether it is possible to unify this feature
also.
Simon Glass [Tue, 5 Mar 2013 14:39:46 +0000 (14:39 +0000)]
arm: Remove use of board_early_init_r/last_stage_init()
These boards define CONFIG_LAST_STAGE_INIT and CONFIG_BOARD_EARLY_INIT_R
but these options are not available on ARM. Move them into the powerpc
common file instead.
This change affects: km_kirkwood_pci, mgcoge3un, kmnusa, kmcoge5un,
km_kirkwood and portl2.
Simon Glass [Tue, 5 Mar 2013 14:39:42 +0000 (14:39 +0000)]
Declare watchdog functions in watchdog.h
These functions are only available for powerpc and are not declared in a
header file. We want to use the rest function in two places (board_f and
board_r), so declare the functions in watchdog.h.
Simon Glass [Fri, 8 Mar 2013 13:45:27 +0000 (13:45 +0000)]
__HAVE_ARCH_GENERIC_BOARD controls availabilty of generic board
We are introducing a new unified board setup. Add a check to make sure that
board config files do not define CONFIG_SYS_GENERIC_BOARD unless their
architecture defines __HAVE_ARCH_GENERIC_BOARD
__HAVE_ARCH_GENERIC_BOARD will currently not be the default setting, but
we can switch this later when most architecture support generic board.
Simon Glass [Tue, 5 Mar 2013 14:39:40 +0000 (14:39 +0000)]
Introduce a basic initcall implementation
This library supports calling a list of functions one after the
other.
It is intended that we move to a more powerful initcall implementation
as proposed by Graeme Russ <graeme.russ@gmail.com>. For now, this allows
us to do the basics.
Simon Glass [Tue, 5 Mar 2013 14:39:37 +0000 (14:39 +0000)]
Introduce generic link section.h symbol files
We create a separate header file for link symbols defined by the link
scripts. It is helpful to have these all in one place and try to
make them common across architectures. Since Linux already has a similar
file, we bring this in even though many of the symbols there are not
relevant to us.
Each architecture has its own asm/sections.h where symbols specifc to
that architecture can be added. For now everything except AVR32 just
includes the generic header.
One change is needed in arch/avr32/lib/board.c to make this conversion
work.
Reviewed-by: Tom Rini <trini@ti.com> (version 5) Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 5 Mar 2013 14:39:35 +0000 (14:39 +0000)]
Introduce generic u-boot.h file
This file holds the board info structure. We need this to be generic
for the unified board series, so create a structure which contains
the basic fields required by the main architectures.
Fabio Estevam [Thu, 14 Mar 2013 02:32:54 +0000 (02:32 +0000)]
nitrogen6x: Fix RAM size variable
Fix the following build error when buildig nitrogen6s1g:
nitrogen6x.c:89:17: error: 'CONFIG_DDR_MB' undeclared (first use in
this function)
nitrogen6x.c:89:17: note: each undeclared identifier is reported only
once for each function it appears in
Reported-by: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tom Warren [Mon, 11 Mar 2013 23:43:49 +0000 (16:43 -0700)]
Tegra114: Dalmore: Add pad config tables/code based on pinmux code
Pad config registers exist in APB_MISC_GP space, and control slew
rate, drive strengh, schmidt, high-speed, and low-power modes for
all of the pingroups in Tegra30. This builds off of the pinmux
way of constructing init tables to configure select pads (SDIOCFG,
for instance) during pinmux_init().
Currently, no padcfg entries exist. SDIO3CFG will be added when the
MMC driver is added as per the TRM to work with the SD-card slot on
Dalmore E1611.
Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tom Warren [Wed, 13 Mar 2013 22:40:33 +0000 (15:40 -0700)]
Tegra114: Dalmore: Always use DEFAULT instead of DISABLE for lock bits
The pinmux code issues a warning if the caller attempts to disable the
lock bit in a pinmux register, since this is impossible (once it's
locked, the only way to unlock it is to reset the device/pmt controller).
The I2C/DDC/CEC/USB macros expect a lock setting to be passed in,
and the previous setting of DISABLE caused the pinmux table parsing
code to issue the warning. Changing the lock bits in these table
entries to DEFAULT (i.e. don't touch it) fixes this.
Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tom Warren [Wed, 13 Mar 2013 22:00:54 +0000 (15:00 -0700)]
Tegra114: pinmux: Fix bad CAM_MCLK func 3 table entry
This caused CAM_MCLK's pinmux reg to be locked out, since the
table parsing code couldn't find a matching entry for VI_ALT3
and wrote garbage to the register.
Stephen Warren [Thu, 28 Feb 2013 15:03:48 +0000 (15:03 +0000)]
ARM: tegra: enable a common set of disk-related commands everywhere
Enable a common set of partition types, filesystems, and related
commands in tegra-common.h, so that they are available on all Tegra
boards. This allows boot.scr (loaded and executed by the default
built-in environment) on those boards to assume that certain features
are always available.
Do this in tegra-common.h, so that individual board files can undefine
the features if they really don't want any of them.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Thu, 28 Feb 2013 15:03:47 +0000 (15:03 +0000)]
disk: define HAVE_BLOCK_DEVICE if CONFIG_CMD_PART
Various code that is conditional upon HAVE_BLOCK_DEVICE is required by
code conditional upon CONFIG_CMD_PART. So, enable HAVE_BLOCK_DEVICE if
CONFIG_CMD_PART is enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Thu, 28 Feb 2013 15:03:46 +0000 (15:03 +0000)]
disk: define HAVE_BLOCK_DEVICE in a common place
This set of ifdefs is used in a number of places. Move its definition
somewhere common so it doesn't have to be repeated.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Tom Warren [Tue, 26 Feb 2013 19:36:22 +0000 (12:36 -0700)]
Tegra30: MMC: Enable DT MMC driver support for Tegra30 Cardhu boards
Tested on my Cardhu-A04 tablet, eMMC and SD-Card work fine, can load
a kernel off of an SD card OK, card detect works, and the env is now
stored in eMMC (end of the 2nd 'boot' sector, same as Tegra20).
Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tom Warren [Tue, 26 Feb 2013 19:31:26 +0000 (12:31 -0700)]
mmc: Tegra: Add SD bus power/voltage function and MMC pad init call.
Tegra30 requires the SD Bus Voltage & Power bits be set in the SD
Power Control register. Tegra20 works w/o them set, but do it anyway
for those SoCs as it's part of the SD spec. Also call a common
board pad init routine (pad_init_mmc) in mmc_reset(), used by
Tegra30 only for now.
Note that Tegra20 SD/MMC HW differs enough from Tegra20 that a
new compatible entry is used in the fdt compat_names/id tables.
Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tom Warren [Wed, 6 Mar 2013 23:16:22 +0000 (16:16 -0700)]
Tegra30: Cardhu: Add pad config tables/code based on pinmux code
Pad config registers exist in APB_MISC_GP space, and control slew
rate, drive strengh, schmidt, high-speed, and low-power modes for
all of the pingroups in Tegra30. This builds off of the pinmux
way of constructing init tables to configure select pads (SDIOCFG,
for instance) during pinmux_init().
Currently, only SDIO1CFG is changed as per the TRM to work with
the SD-card slot on Cardhu.
Thanks to StephenW for the suggestion/original idea.
Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Use the latest tables & code from our internal U-Boot repo.
The SDMMC3_CD, CLK_LB_IN and CLK_LB_OUT offsets in the pingroup
table were off by a few indices, causing the pinmux init code to
write bad data to the PINMUX_AUX_ regs. This also enabled the lock
bit, which made it impossible to reconfig the pads correctly for
SDMMC3 (SD card on Dalmore) operation. Also fixes SPI_CS2_N,
USB_VBUS_EN0, HDMI_CEC and UART2_RXD/TXD muxes.
Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Thu, 28 Feb 2013 12:40:09 +0000 (12:40 +0000)]
ARM: tegra: implement WAR for Tegra114 CPU reset vector
A Tegra114 HW bug prevents the main CPU vector from being modified under
certain circumstances. Tegra114 A01P and later with a patched boot ROM
set the CPU reset vector to 0x4003fffc (end of IRAM). This allows placing
an arbitrary jump instruction at that location, in order to redirect to
the desired reset vector location. Modify Tegra114's start_cpu() to make
use of this feature. This allows CPUs with the patched boot ROM to boot.
Based-on-work-by: Jimmy Zhang <jimmzhang@nvidia.com>. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Tom Warren [Thu, 21 Feb 2013 12:31:29 +0000 (12:31 +0000)]
Tegra: fdt: Add/enhance sdhci (mmc) nodes for all T20 DT files
Linux dts files were used for those boards that didn't already
have sdhci info populated. Tamonten has their own dtsi file with
common sdhci nodes (sourced from Linux).
Signed-off-by: Tom Warren <twarren@nvidia.com> Tested-by: Thierry Reding <thierry.reding@avionic-design.de> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tom Warren [Thu, 21 Feb 2013 12:31:27 +0000 (12:31 +0000)]
Tegra: fdt: Change /include/ to #include for C preprocessor
dts Makefile has the arch & board include paths added to DTS_CPPFLAGS.
This allows the use of '#include "xyz"' in the dts/dtsi file which
helps the C preprocessor find common dtsi include files.
Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tom Warren [Fri, 8 Feb 2013 07:25:31 +0000 (07:25 +0000)]
Tegra114: fdt: Update DT files with I2C info for T114/Dalmore
T114, like T30, does not have a separate/different DVC (power I2C)
controller like T20 - all 5 I2C controllers are identical, but
I2C5 is used to designate the controller intended for power
control (PWR_I2C in the schematics). PWR_I2C is set to 400KHz.
Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Laxman Dewangan <ldewangan@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tom Warren [Fri, 8 Feb 2013 07:25:30 +0000 (07:25 +0000)]
Tegra: I2C: Add T114 clock support to tegra_i2c driver
T114 has a slightly different I2C clock, with a new (extra) divisor
in standard/fast mode and HS mode. Tested on my Dalmore, and the I2C
clock is 100KHz +/- 3Hz on my Saleae Logic analyzer.
Added a new entry in compat_names for T114 I2C since it differs
from the previous Tegra SoCs. A flag is set when T114 I2C HW is
found so new features like the extra clock divisor can be used.
Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Tom Warren [Wed, 27 Feb 2013 11:10:01 +0000 (11:10 +0000)]
Tegra114: I2C: Take DVFS out of reset to allow I2C5 (PWR_I2C) to work
I2C driver can now probe dev 0 (PWR_I2C, where the PMU, etc. lives).
This is needed so that the SDIO slot power can be brought up for
the MMC driver, so it has to precede those commits.
Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Lucas Stach [Thu, 7 Feb 2013 07:16:29 +0000 (07:16 +0000)]
tegra: usb: move implementation into right directory
This moves the Tegra USB implementation into the drivers/usb/host
directory. Note that this merges the old
/arch/arm/cpu/armv7/tegra20/usb.c file into ehci-tegra.c. No code
changes, just moving stuff around.
v2: While at it also move some defines and the usb.h header file to make
usb driver usable for Tegra30.
NOTE: A lot more work is required to properly init the PHYs and PLL_U on
Tegra30, this is just to make porting easier and it does no harm here.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Lucas Stach [Thu, 7 Feb 2013 07:16:25 +0000 (07:16 +0000)]
tegra: usb: make controller init functions more self contained
There is no need to pass around all those parameters. The init functions
are able to easily extract all the needed setup info on their own.
This allows to move out the controller init into ehci_hcd_init later
on, without having to save away global state for later use and thus
bloating the file global state.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Tue, 26 Feb 2013 12:28:28 +0000 (12:28 +0000)]
ARM: tegra: enable some CPU errata workarounds
Tegra20 has a Cortex A9 r1p1, and Tegra30 has a Cortex A9 r2p9. As such,
some CPU errata exist, and must be worked around.
These must be worked around in the bootloader, since in general, the
kernel (especially a multi-platform kernel) needs to support being
launched in non-secure mode (normal world), and hence may not be able
to write to the CP15 register to enable these workarounds.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Tue, 26 Feb 2013 12:28:27 +0000 (12:28 +0000)]
ARM: implement some Cortex-A9 errata workarounds
Various errata exist in the Cortex-A9 CPU, and may be worked around by
setting some bits in a CP15 diagnostic register. Add code to implement
the workarounds, enabled by new CONFIG_ options.
This code was taken from the Linux kernel, v3.8, arch/arm/mm/proc-v7.S,
and modified to remove the logic to conditionally apply the WAR (since we
know exactly which CPU we're running on given the U-Boot configuration),
and use r0 instead of r10 for consistency with the rest of U-Boot's
cpu_init_cp15().
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Albert ARIBAUD [Mon, 25 Feb 2013 00:59:00 +0000 (00:59 +0000)]
Refactor linker-generated arrays
Refactor linker-generated array code so that symbols
which were previously linker-generated are now compiler-
generated. This causes relocation records of type
R_ARM_ABS32 to become R_ARM_RELATIVE, which makes
code which uses LGA able to run before relocation as
well as after.
Note: this affects more than ARM targets, as linker-
lists span possibly all target architectures, notably
PowerPC.
Albert ARIBAUD [Mon, 25 Feb 2013 00:58:59 +0000 (00:58 +0000)]
arm: make __bss_start and __bss_end__ compiler-generated
Turn __bss_start and __bss_end__ from linker-generated
to compiler-generated symbols, causing relocations for
these symbols to change type, from R_ARM_ABS32 to
R_ARM_RELATIVE.
This should have no functional impact, as it affects
references to __bss_start and __bss_end__ only before
relocation, and no such references are done.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Albert ARIBAUD [Mon, 25 Feb 2013 00:58:58 +0000 (00:58 +0000)]
Remove linker lists (LGAs) from SPL linker scripts
Many SPL linker scripts needlessly include linker lists (aka LGAs).
Remove them whenever possible; keep it only in the seven am335x_evm
variants (am335x_evm, am335x_evm_uart[1-5], am335x_evm_spiboot),
where there is actual content in output section .u_boot_list.
This commit keeps all u-boot.bin and u-boot-spl.bin in ARM targets
byte-identical.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Albert ARIBAUD [Mon, 25 Feb 2013 00:58:57 +0000 (00:58 +0000)]
arm: omap: map u_boot_lists section to .sram
Output section .u_boot_list was left unmapped in
u-boot-spl.lds for omap-common, causing the location
counter to roll back to bteween .rodata and .data,
making __image_copy_end and _end symbols wrong.
Mapping output section .u_boot_list to memory .sram
fixes these symbols' mapping.
This modifies the SPL binary but has no functional
impact, as __image_copy_end and _end are never used
in SPLs and u_boot_list is empty for all 29 boards
affected (omap4_sdp4430 eco5pk igep0030 am335x_evm_uart3
omap3_beagle am3517_crane igep0032 mt_ventoux pcm051
am3517_evm omap3_evm_quick_mmc am335x_evm_uart2
am335x_evm_spiboot am335x_evm_uart1 omap3_evm igep0030_nand
omap3_overo igep0020 am335x_evm omap4_panda omap5_evm
am335x_evm_uart4 devkit8000 tricorder mcx twister
omap3_evm_quick_nand am335x_evm_uart5 igep0020_nand).
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
1) Write the correct M/T Stop value to I2CSTAT after i2c write.
According to the spec, after finish the data transmission, we should
write a M/T Stop (I2C_MODE_MT | I2C_TXRX_ENA) to I2CSTAT instead of
a M/R Stop (I2C_MODE_MR | I2C_TXRX_ENA).
2) Not split the write to I2CSTAT into 2 steps in i2c read.
According to the spec, we should write the combined M/R Start value to
I2CSTAT after setting the slave address to I2CDS
3) Fix the mistake of making an equality check to an assignment.
In the case of I2C write with the zero-length address, while tranfering the
data, it should be an equality check (==) instead of an assignment (=).
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Joe Hershberger [Fri, 8 Feb 2013 10:28:00 +0000 (10:28 +0000)]
CONFIG_BOOTDELAY default should not affect runtime
Because the code that handles bootdelay is compiled in conditionally
based on the default value, you are restricted in the default,
regardless of what you want the runtime options to be.
Change the source to always check if any default is given so that other
values can be selected and used at runtime.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Wolfgang Denk [Wed, 20 Feb 2013 04:53:16 +0000 (04:53 +0000)]
env: fix "env ask" command
The "env ask" traditionally uses a somewhat awkward syntax:
env ask name [message ...] [size]
So far, when a mesage was given, you always also had to enter a size.
If you forgot to do that, the command would terminate without any
indication of the problem.
To avoid incompatible changes of the interface, we now check the last
argument if it can be converted into a decimal number. If this is the
case, we assume it is a size; otherwise we treat it as part of the
message.
Also, add a space after the message fore easier reading,
and clean up help mesage.
Tom Rini [Thu, 21 Feb 2013 06:55:40 +0000 (06:55 +0000)]
cmd_fat.c: Note in fatread help about alignment requirements
When using the partial read feature of fatwrite the buffer we read into
can become unaligned not just due to initial location but the size of
our partial reads as well. Make this clear in the help text.
projects / u-boot.git / log