Marek Vasut [Thu, 24 Nov 2011 04:14:00 +0000 (05:14 +0100)]
USB: MX5: Add MX5 usb post-init callback
This is useful for USB Transceivers init etc.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com>
Marek Vasut [Thu, 24 Nov 2011 03:22:17 +0000 (04:22 +0100)]
USB: MX5: Abstract out mx51 USB pixmux configuration
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com>
USB: MX5: add generic USB EHCI support for mx51 and mx53
It's derived from ehci-mxc and uses the header files of the
ehci-fsl interface. The callback board_ehci_hcd_init() has
been introduced to allow for board-specific setup when USB
is started.
USB: MX5: add helper functions to enable USB clocks
Signed-off-by: Wolfgang Grandegger <wg@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com>
V2: Fix spacing in crm_regs.h
Vincent Palatin [Mon, 5 Dec 2011 22:52:22 +0000 (14:52 -0800)]
ehci: speed up initialization
According to EHCI specification v1.0, the controller should stabilize
the power on a port at most 20 ms after the port power bit transition.
So, we put this setting in the virtual descriptor corresponding field,
(bPwrOn2PwrGood = 10 => 10 x 2ms = 20ms), this saves about 500ms at each
controller initialization/enumeration.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
usb: align usb_endpoint_descriptor to 16-bit boundary
The usb_endpoint_descriptor struct is 7 bytes large and is
defined as an array (ep_desc[USB_MAXENDPOINTS])
in the usb_interface struct in include/usb.h
This fact will result in that every odd index in that
array will start at an uneven address, this in
turn makes accesses to u16 wMaxPacketSize unaligned.
Such accesses are illegal on the OpenRISC architecture
(as well as other architectures) and will render a bus error.
Setting the aligned(2) attribute on usb_endpoint_descriptor
will force wMaxPacketSize to a 16-bit boundary.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Marek Vasut [Mon, 10 Oct 2011 15:34:27 +0000 (17:34 +0200)]
USB: Drop dead code from usb_kbd.c
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Denk <wd@denx.de>
Marek Vasut [Mon, 10 Oct 2011 15:34:26 +0000 (16:34 +0100)]
USB: Rework usb_kbd.c
* Support dynamic allocation of devices
* Passing data via usb device privptr
* Reorder functions to avoid forward declarations
* Introduce generic polling mechanism to fix musb and ehci-hcd breakage
due to using "extern new;" to access keyboard driver data!
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Denk <wd@denx.de>
Marek Vasut [Sun, 25 Sep 2011 19:00:37 +0000 (20:00 +0100)]
USB: Add functionality to poll the USB keyboard via control EP
This allows the keyboard to avoid requests via Interrupt Endpoint altogether and
run all requests via Control Endpoint. This uses the Get_Report request.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Remy Bohmer <linux@bohmer.net>
Rebased on current code.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Tom Rini <trini@ti.com> Cc: Heiko Schocher <hs@denx.de> Cc: Wolfgang Denk <wd@denx.de>
arm, davinci: Use lldiv for the 64-bit divisions in timer.c
Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Tom Rini <trini@ti.com> Cc: Heiko Schocher <hs@denx.de> Cc: Wolfgang Denk <wd@denx.de>
Fix:
flash.c: In function 'flash_get_offsets':
flash.c:122:10: warning: variable 'pOrgDef' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'flash_erase':
flash.c:263:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:439:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Dave Peverley <dpeverley@mpc-data.co.uk> Acked-by: Tom Rini <trini@ti.com>
Fix:
flash.c: In function 'flash_get_offsets':
flash.c:139:10: warning: variable 'pOrgDef' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'flash_erase':
flash.c:280:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:456:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Tom Rini <trini@ti.com>
Fix:
edminiv2.c: In function 'reset_phy':
edminiv2.c:98:2: warning: implicit declaration of function
'mv_phy_88e1116_init' [-Wimplicit-function-declaration]
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Fix:
apollon.c: In function 'dram_init':
apollon.c:188:29: warning: variable 'cpu' set but not used
[-Wunused-but-set-variable]
apollon.c:188:20: warning: variable 'rev' set but not used
[-Wunused-but-set-variable]
apollon.c:187:26: warning: variable 'size1' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Kyungmin Park <kyungmin.park@samsung.com>
Fix:
yaffs_guts.c: In function 'yaffs_GarbageCollectBlock':
yaffs_guts.c:2761:6: warning: variable 'retVal' set but not used
[-Wunused-but-set-variable]
Here GCC actually detected a bug. The code was always returning OK
instead of the previously set retrun code. Fix that.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: William Juul <wiljuul@cisco.com> Cc: Scott Wood <scottwood@freescale.com> Acked-by: William Juul <wiljuul@cisco.com>
Fix:
at91_emac.c: In function 'at91emac_phy_init':
at91_emac.c:244:20: warning: variable 'duplex' set but not used
[-Wunused-but-set-variable]
at91_emac.c:244:13: warning: variable 'speed' set but not used
[-Wunused-but-set-variable]
Use new debug_cond() to fix these warnings. In the result, anumber of
inconsistent printf() formats are detected:
at91_emac.c: In function 'at91emac_read':
at91_emac.c:147:2: warning: format '%x' expects argument of type
'unsigned int', but argument 2 has type 'struct at91_emac_t *'
[-Wformat]
at91_emac.c: In function 'at91emac_write':
at91_emac.c:157:2: warning: format '%x' expects argument of type
'unsigned int', but argument 2 has type 'struct at91_emac_t *'
[-Wformat]
at91_emac.c:157:2: warning: format '%x' expects argument of type
'unsigned int', but argument 4 has type 'short unsigned int *'
[-Wformat]
at91_emac.c: In function 'at91emac_recv':
at91_emac.c:451:3: warning: format '%d' expects argument of type
'int', but argument 2 has type 'long unsigned int' [-Wformat]
at91_emac.c:451:3: warning: format '%x' expects argument of type
'unsigned int', but argument 4 has type 'long unsigned int' [-Wformat]
Fix these, too.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Jens Scharsig <js_at_ng@scharsoft.de> Cc: Andreas Bießmann <andreas.devel@gmail.com> Cc: Reinhard Meyer <u-boot@emk-elektronik.de>
Fix:
ne2000_base.c: In function 'dp83902a_send':
ne2000_base.c:282:7: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
ne2000_base.c: In function 'dp83902a_RxEvent':
ne2000_base.c:376:5: warning: variable 'rsr' set but not used
[-Wunused-but-set-variable]
ne2000_base.c: In function 'dp83902a_TxEvent':
ne2000_base.c:513:5: warning: variable 'tsr' set but not used
[-Wunused-but-set-variable]
ne2000_base.c: In function 'dp83902a_ClearCounters':
ne2000_base.c:550:17: warning: variable 'cnt3' set but not used
[-Wunused-but-set-variable]
ne2000_base.c:550:11: warning: variable 'cnt2' set but not used
[-Wunused-but-set-variable]
ne2000_base.c:550:5: warning: variable 'cnt1' set but not used
[-Wunused-but-set-variable]
Wolfgang Denk [Sat, 10 Dec 2011 21:46:48 +0000 (22:46 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
M28: Cleanup memsize.o OOT build
i.MX28: Move SPL to arch/arm/cpu/arm926ejs/mx28
M28: Fix typo
M28: Document that units has to be set to sectors on SD bootcard
i.mx: i.mx6q: add the initial support for i.mx6q ARM2 board
i.mx: mxc_gpio: add the i.mx6q support
i.mx: add the initial support for freescale i.MX6Q processor
i.mx: introduce the armv7/imx-common folder
S5PC2XX: Rename S5pc2XX to exynos
tegra2: Don't use board pointer before it is set up
tegra2: Remove unneeded 'dynamic ram size' message
tegra2: Remove unused low-level Tegra2 UART code
tegra2: Remove unneeded config option
tegra2: Remove unneeded boot code
tegra2: Enable instruction cache
arm: Move CP15 init out of cpu_init_crit()
tegra2: Simplify tegra_start() boot path
tegra2: Add arch_cpu_init() to fire up Cortex-A9
tegra2: Use new GPIO APIs in gpio_config_uart()
tegra2: Add support for Ventana
tegra2: Modify MMC driver to handle power and cd GPIOs
tegra2: Move board_mmc_init into board files
Wolfgang Denk [Sat, 10 Dec 2011 21:45:34 +0000 (22:45 +0100)]
Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-staging
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
Update pci_ids.h from current Linux sources
omap: overo: Use ubifs instead of jffs2 for nand
omap: TWL4030 Bump VMMC1 interface voltage from 3V to 3.15V
Marek Vasut [Thu, 8 Dec 2011 09:46:12 +0000 (09:46 +0000)]
M28: Cleanup memsize.o OOT build
The current way memsize.c is built just made a symlink into the directory
with SPL and then compiled it like any other file there. This was bad as that
broke the out-of-tree build.
The new way introduced in this patch uses the standard spl/Makefile methods
(CONFIG_SPL_LIBCOMMON_SUPPORT / CONFIG_SPL_LIBGENERIC_SUPPORT) to let files in
common/ be built. Because common/Makefile says memsize.c is always built (SPL
and non-SPL build), this fixes our issue with memsize.c out-of-tree build.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Stefano Babic <sbabic@denx.de>
Jason Liu [Fri, 25 Nov 2011 00:18:05 +0000 (00:18 +0000)]
i.mx: i.mx6q: add the initial support for i.mx6q ARM2 board
Add the initial support for Freescale i.MX6Q Armadillo2 board
Support: MMC boot from slot 0/1, debug UART(UART4), usdhc.
There is two MMC slots on the boards:
mmc dev 0 -> connect USDHC3 -> the lower slot on the board,
mmc dev 1 -> connect USDHC4 -> the upper slot on the board,
Signed-off-by: Jason Liu <jason.hui@linaro.org> Cc: Stefano Babic <sbabic@denx.de> Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Jason Liu [Fri, 25 Nov 2011 00:18:01 +0000 (00:18 +0000)]
i.mx: introduce the armv7/imx-common folder
In order to support the coming MX6 platform and to reducde
the duplicated code, we had better move some common files
or functions to the imx-common folder for sharing.
This patch does the following:
- move speed.c file from armv7/mx5/speed.c to armv7/imx-common/speed.c
- move armv7/mx5/timer.c to armv7/imx-common/timer.c, no any new feature
added but just fix the checkpatch errors in the old file and remove
the CONFIG_SYS_MX5_CLK32 reference in the file
- create one new file cpu.c file to store the common function with i.mx5/6
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc:Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
Chander Kashyap [Tue, 6 Dec 2011 23:34:12 +0000 (23:34 +0000)]
S5PC2XX: Rename S5pc2XX to exynos
As per new naming convention for Samsung SoC's, all Cortex-A9 and Cortex-A15
based SoC's will be classified under the name Exynos. Cortex-A9 and Cortex-A15
based SoC's will be sub-classified as Exynos4 and Exynos5 respectively.
In order to better adapt and reuse code across various upcoming Samsung Exynos
based boards, all uses of s5pc210 prefix/suffix/directory-names are renamed in
this patch. s5pc210 is renamed as exynos4210 and S5PC210/s5pc210 suffix/prefix
are renamed as exynos4/EXYNOS4.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Simon Glass [Sat, 5 Nov 2011 03:56:57 +0000 (03:56 +0000)]
tegra2: Don't use board pointer before it is set up
In board_init_f() the gd->bd pointer is not valid when dram_init() is called.
This only avoids dying because DRAM is at zero on Tegra2. The common ARM
routine sets up the banks in the same way anyway, so we can just remove this
code.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Sat, 5 Nov 2011 03:56:55 +0000 (03:56 +0000)]
tegra2: Remove unused low-level Tegra2 UART code
This was used by the AVP in early boot but is no longer used. Unless we
plan to enable it somehow it is not needed. In any case we should try
to use the ns16550 driver instead as it has the same code.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Sat, 5 Nov 2011 03:56:52 +0000 (03:56 +0000)]
tegra2: Enable instruction cache
Since low-level init is skipped, the instruction cache is never enabled on
Tegra2. This explicitly calls this initialization as soon as the A9 is
initialized.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Sat, 5 Nov 2011 03:56:51 +0000 (03:56 +0000)]
arm: Move CP15 init out of cpu_init_crit()
Some SOCs have do not start up with their 'main' CPU. The first U-Boot
code may then be executed with a CPU which does not have a CP15, or not a
useful one.
Here we split the initialization of CP15 into a separate call, which can
be performed later if required.
Once the main CPU is running, you should call cpu_init_cp15() to perform
this init as early as possible.
Existing ARMv7 boards which define CONFIG_SKIP_LOWLEVEL_INIT should not
need to change, this CP15 init is still skipped in that case. The only
impact for these boards is that the cpu_init_cp15() will be available
even if it is never used on these boards.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Sat, 5 Nov 2011 03:56:50 +0000 (03:56 +0000)]
tegra2: Simplify tegra_start() boot path
The Tegra2 boot path is more complicated than it needs to be. Since we want
to move to building most of U-Boot with ARMv7 and only a small part with
ARMv4T (for AVP) it should be as simple as possible.
This makes tegra2_start() into a simple function which either does AVP
init or A9 init depending on which core is running it. Both cores now
following the same init path, beginning at _start, and the special Tegra2
boot path code is no longer required.
Only two files need to be built for ARMv4T, and this is handled in the
Tegra2 CPU Makefile.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Sat, 5 Nov 2011 03:56:49 +0000 (03:56 +0000)]
tegra2: Add arch_cpu_init() to fire up Cortex-A9
We want to move away from a special Tegra2 start-up, and just use
arch_cpu_init() instead. However, if we run board_init_f() from boot
we need to build it for ARMv4T, since the Tegra's AVP start-up CPU
does not support ARMv7.
The effect of this is to do the AVP init earlier, and in
arch_cpu_init(), rather that board_early_init_f().
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Thu, 6 Oct 2011 12:52:22 +0000 (12:52 +0000)]
tegra2: Use new GPIO APIs in gpio_config_uart()
... rather than open-coding the register accesses.
However, gpio_request() typically stores the "label" parameter in a global
data structure. This causes problems when called from gpio_config_uart(),
since the code is running before relocation. To solve this, pass a NULL
string to gpio_request(), and modify gpio_request() not to touch the string
if it's NULL.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 31 Oct 2011 06:51:37 +0000 (06:51 +0000)]
tegra2: Add support for Ventana
Ventana is a board which is very similar to Seaboard. Support it by
re-using board/nvidia/seaboard/seaboard.c with minor run-time conditionals.
v5: Makefile: Use cmd_link_o_target, remove unused clean/distclean targets.
v6: Make gpio_config_uart_seaboard() static.
v7: Add MAINTAINERS entry for Ventana. Tom Warren doesn't have Ventana, so
he asked me to add myself for this board.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 31 Oct 2011 06:51:36 +0000 (06:51 +0000)]
tegra2: Modify MMC driver to handle power and cd GPIOs
Pass the GPIO numbers for power and card detect to tegra2_mmc_init(), and
modify that function to perform all required GPIO initialization. This
removes the need for board files to perform these operations.
Move board_mmc_getcd() into tegra2_mmc.c now that the driver knows which
GPIOs to use.
Update affected call-sites in seaboard.c and harmony.c. Note that this
change should make all SD ports work on Harmony, since the required GPIO
setup is now being performed.
v4: Fix prototype of tegra2_mmc_init() in board.h to match driver change.
Remove prototype of gpio_config_mmc() from board.h
Signed-off-by: Stephen Warren <swarren@nvidia.com> Cc: Andy Fleming <afleming@gmail.com> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 31 Oct 2011 06:51:35 +0000 (06:51 +0000)]
tegra2: Move board_mmc_init into board files
For Seaboard, this is mostly a cut/paste of board_mmc_init() and
pin_mux_mmc() into seaboard.c; pin_mux_mmc() was modified to add some
missing pinmux_tristate_disable calls for the GPIOs.
For Harmony, those functions were modified to configure SDMMC2 (index 2)
instead of SDMMC3 (index 1), since that's what is present on the board.
However, harmony.c is still missing the required GPIO setup, so neither
port is likely to function correctly yet. This will be fixed in the next
change.
v4: Include board.h to prototype tegra2_mmc_init().
Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Gabe Black [Mon, 7 Nov 2011 23:43:32 +0000 (23:43 +0000)]
Update pci_ids.h from current Linux sources
This change copies over the pci_ids.h file from Linux verbatim, plus a few
ids that had been added by hand. The last non-merge change hash in that
file in the kernel repository was:
Signed-off-by: Gabe Black <gabeblack@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
[agust@denx.de: updated to preserve used PCI IDs] Signed-off-by: Anatolij Gustschin <agust@denx.de>
Ash Charles [Wed, 28 Sep 2011 06:47:16 +0000 (06:47 +0000)]
omap: TWL4030 Bump VMMC1 interface voltage from 3V to 3.15V
MMC interfaces are specified to be 3.3V compatible with an operating
voltage range of 3.1V to 3.5V for SD cards. This change affects
hardware using TWL4030 (TPS6595x) PMICs and should improve the
reliability when communicating with marginally-spec'd MMC devices.
3.15V is the highest possible level for this chip. This patch
has been tested on a Gumstix Overo board.
Signed-off-by: Ash Charles <ash@gumstix.com> Tested-by: Steve Sakoman <steve@sakoman.com>
Kyle Moffett [Wed, 7 Dec 2011 21:39:16 +0000 (16:39 -0500)]
mpc85xx: Add board support for the eXMeritus HWW-1U-1A devices
The eXMeritus HWW-1U-1A unit is a DO-160-certified 13lb 1U chassis
with 3 independent TEMPEST zones. Two independent P2020 computers may
be found inside each zone. Complete hardware support is included.
High-level hardware overview:
* DO-160 certified for passenger aircraft (noncritical)
* TEMPEST ceritified for RED/BLACK separation
* 3 zones per chassis, 2 computers per zone (total of 6)
* Dual-core 1.066GHz P2020 per computer
* One 2GB DDR2 SO-RDIMM module per computer (upgradable to 4GB)
* Removable 80GB or 160GB Intel X18-M SSD per computer
* Front-accessible dual-port E1000E per computer
* Front-accessible serial console per computer
* Front-accessible USB port per computer
* Internal Gigabit crossover within each TEMPEST zone
* Internal unidirectional fiber links across TEMPEST zones
* Battery-backed DS1339 I2C RTC on each CPU.
Combined, each 13lb 1U chassis contains 12GB RAM, 12 cores @ 1.066GHz,
12 front-accessible Gigabit Ethernet ports and 960GB of solid-state
storage with a total power consumption of ~200W.
Additional notes:
* SPD detection is only known to work with the DO-160-certified DIMMs
* CPU reset is a little quirky due to hardware misfeature. Proper
support for the hardware reset mechanism has been left for a later
patch series to address.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Andy Fleming <afleming@gmail.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simon Glass [Tue, 18 Oct 2011 13:43:20 +0000 (13:43 +0000)]
Add board_pre_console_putc to deal with early console output
This patch adds support for console output before the console is inited.
The main purpose of this is to deal with a very early panic() which would
otherwise cause a silent hang.
A new board_pre_console_putc() function is added to the board API. If
provided by the board it will be called in the event of console output
before the console is ready. This function should turn on all UARTs and
spray the character out if it possibly can.
The feature is controlled by a new CONFIG_PRE_CONSOLE_PUTC option.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Graeme Russ <graeme.russ@gmail.com>
Fix:
musb_udc.c: In function 'musb_peri_softconnect':
musb_udc.c:166:14: warning: variable 'intrtx' set but not used
[-Wunused-but-set-variable]
musb_udc.c:166:6: warning: variable 'intrrx' set but not used
[-Wunused-but-set-variable]
musb_udc.c:165:5: warning: variable 'intrusb' set but not used
[-Wunused-but-set-variable]
Simon Glass [Tue, 15 Nov 2011 18:17:06 +0000 (18:17 +0000)]
Fix warnings in arch/arm/cpu/arm920t/s3c24x0/usb_ohci.c
Sorry if this is already fixed somewhere - I could not find it.
This fixes these warnings:
usb_ohci.c: In function 'submit_control_msg':
usb_ohci.c:1081: warning: dereferencing pointer 'data_buf.76' does break strict-aliasing rules
usb_ohci.c:1081: note: initialized from here
usb_ohci.c:1084: warning: dereferencing pointer 'data_buf.76' does break strict-aliasing rules
usb_ohci.c:1084: note: initialized from here
usb_ohci.c:1087: warning: dereferencing pointer 'data_buf.76' does break strict-aliasing rules
usb_ohci.c:1087: note: initialized from here
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 10 Oct 2011 05:34:25 +0000 (05:34 +0000)]
USB: Squash checkpatch warnings in usb_kbd.c
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Mike Frysinger <vapier@gentoo.org>
Rebased to current code.
Bernhard Kaindl [Thu, 20 Oct 2011 10:56:59 +0000 (10:56 +0000)]
ne2000: Convert to new net-multi model, fixes build of three boards
This fixes the build of the two sh boards shmin and r7780mp and qemu-mips
which currently fail to build due to dropped pre-CONFIG_NET_MULTI code.
This v2 patch minimizes the number of lines in the diff for easy review
and to eliminate any possible accidential changes resulting from moving
lines of code in the file. This also makes the register function very easy.
Any cleanups and improvements are intentionally deferred to follow-up patches
to keep this patch as simple and as easy to review as possible.
A new driver register function, ne2k_register() calls the existing
one-time setup part of the old init function and calls eth_register().
Changes to shmin, r7780mp and qemu-mips:
- Call the new ne2k_register() from board_eth_init() of the boards.
- Tested using qemu-mips board,
- Tested the two renesas / sh boards r7780mp and shmin to compile again,
and should work.
checkpatch-clean when "--ignore VOLATILE" is added to .checkpatch.conf,
and no warnings introduced in none of the three boards using this driver.
Signed-off-by: Bernhard Kaindl <bernhard.kaindl@gmx.net>
Kyle Moffett [Wed, 23 Feb 2011 06:40:38 +0000 (06:40 +0000)]
powerpc: Minimal private libgcc to build on Debian
Standard Debian powerpc and powerpcspe systems only include hard-float
libgcc in their native compilers, which causes scary build warnings when
building U-Boot.
Debian and other PowerPC-supporting distributions used to provide libgcc
and other libraries in a "nof" (soft-float) form in the "multilib"
packages. As they were completely unused by the distribution and
therefore tended to be very buggy it was decided to save some time on
the part of the maintainers and build-servers by removing them.
Admittedly, right now the linker warnings do not indicate any problems,
as the included routines do not use any floating point at all.
The concern is that if floating-point code were ever added it might
cause hard-float code to be unexpectedly included in U-Boot without
generating a hard error. This would cause unexplained crashes or
indeterminate results at runtime.
The easiest way to resolve this is to borrow the routines that U-Boot
needs from the Linux kernel, which has the same issue.
Specifically, the routines are: _ashldi3(), _ashrdi3(), and _lshrdi3().
They were borrowed from arch/powerpc/kernel/misc_32.S as of v2.6.38-rc5,
commit 85e2efbb1db9a18d218006706d6e4fbeb0216213, and are GPLv2+.
The Makefile framework was copied from the U-Boot ARM port.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: Andy Fleming <afleming@gmail.com> Cc: Kumar Gala <kumar.gala@freescale.com> Cc: Stefan Roese <sr@denx.de>
definded CONFIG_SYS_NAND_HW_ECC_OOBFIRST:
nand_spl_simple.c: In function 'nand_read_page':
nand_spl_simple.c:156:6: warning: variable 'stat' set but not used
[-Wunused-but-set-variable]
not definded CONFIG_SYS_NAND_HW_ECC_OOBFIRST:
nand_spl_simple.c: In function 'nand_read_page':
nand_spl_simple.c:196:6: warning: variable 'stat' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Scott Wood <scottwood@freescale.com> Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Fix:
cfb_console.c:371: warning: 'cursor_state' defined but not used
cfb_console.c:372: warning: 'old_col' defined but not used
cfb_console.c:373: warning: 'old_row' defined but not used
cfb_console.c:435: warning: 'video_invertchar' defined but not used
Signed-off-by: Anatolij Gustschin <agust@denx.de> Tested-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Wed, 7 Dec 2011 08:09:58 +0000 (09:09 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
davinci: Remove unwanted memsize.c from hawkboard's nand spl build
devkit8000: Move CONFIG_SYS_TEXT_BASE out of bss
da850evm: pass board revision info to kernel
arch/arm/include/asm/arch-omap5/clocks.h: Fix GCC 4.2 warnings
arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix GCC 4.6 warnings
arch/arm/cpu/armv7/omap-common/spl.c: Fix GCC 4.2 warnings
MX35: flea3: changes due to hardware revision B
MX: serial_mxc: cleanup removing nasty #ifdef
M28: Fix OB1 bug in GPIO driver
MXS: Add static annotations to dma driver
apbh_dma: return error value on timeout
Efika: Configure additional regulators for HDMI output
mx5: Correct a warning in clock.c
MC13892: Add REGMODE0 bits definitions
mx51evk: Configure the pins as GPIOs prior to using gpio_get_value
mx53smd: Configure the pins as GPIOs prior to using gpio_get_value
mx53evk: Configure the pins as GPIOs prior to using gpio_get_value
mx53ard: Configure the pins as GPIOs prior to using gpio_get_value
mx53loco: Configure the pins as GPIOs prior to using gpio_get_value
OMAP3: Add SPL_BOARD_INIT hook
AM3517 CraneBoard: Add SPL support
AM3517: Add SPL support
OMAP3: Add SPL support to omap3_evm
OMAP3: Add SPL support to Beagleboard
OMAP3 SPL: Add identify_nand_chip function
OMAP3 SPL: Rework memory initalization and devkit8000 support
OMAP3: Suffix all Micron memory timing parts with their speed
OMAP3: Add optimal SDRC autorefresh control values
omap3: mem: Add MCFG helper macro
OMAP3: Remove get_mem_type prototype
OMAP3: Change mem_ok to clear again after reading back
OMAP3: Add a helper function to set timings in SDRC
OMAP3: Update SDRC dram_init to always call make_cs1_contiguous()
omap3: mem: Comment enable_gpmc_cs_config more
ARM: davici_emac: Fix condition for number of phy detects
arm: printf() is not available in some SPL configurations
arm, davinci: add support for am1808 based enbw_cmc board
arm, davinci: move misc function in arch tree
arm, board/davinci/common/misc.c: Codingstyle cleanup
arm, davinci, da850: add uart1 tx rx pinmux config
arm, davinci: move davinci_rtc struct to hardware.h
arm, davinci: Remove duplication of pinmux configuration code
arm, hawkboard: Use the pinmux configurations defined in the arch tree
arm, da850evm: Use the pinmux configurations defined in the arch tree
arm, da850: Add pinmux configurations to the arch tree
arm, da850evm: Do pinmux configuration for EMAC together with other pinmuxes
arm, hawkboard: Remove obsolete struct pinmux_config i2c_pins
arm, davinci: Move pinmux functions from board to arch tree
arm, arm926ejs: always do cpu critical inits
omap_gpmc: use SOFTECC in SPL if it's enabled
nand_spl_simple: add support for software ECC
AM3517: move AM3517 specific mux defines to generic header
AM35xx: add EMAC support
davinci_emac: hardcode 100Mbps for AM35xx and RMII
davinci_emac: fix for running with dcache enabled
arm926ejs: add noop implementation for dcache ops
davinci_emac: conditionally compile specific PHY support
davinci_emac: use internal addresses in buffer descriptors
davinci_emac: move arch-independent defines to separate header
BeagleBoard: config: Really switch to ttyO2
ARM: davinci_dm6467Tevm: Fix build breakage
ARM: OMAP: Remove STACKSIZE for IRQ and FIQ if unused
ARM: OMAP3: Remove unused define SDRC_R_C_B
ARM: OMAP3: Remove unused define CONFIG_OMAP3430
omap4: fix IO setting
omap4+: streamline CONFIG_SYS_TEXT_BASE and other SDRAM addresses
omap4460: add ES1.1 identification
omap4: emif: fix error in driver
omap: remove I2C from SPL
omap4460: fix TPS initialization
omap: fix cache line size for omap3/omap4 boards
omap4: ttyO2 instead of ttyS2 in default bootargs
omap: Improve PLL parameter calculation tool
start.S: remove omap3 specific code from start.S
armv7: setup vector
armv7: include armv7/cpu.c in SPL build
armv7: disable L2 cache in cleanup_before_linux()
arm, arm926ejs: Fix clear bss loop for zero length bss
PXA: Move colibri_pxa270 to board/toradex/
PXA: Flip colibri_pxa27x to pxa-common.h
PXA: Introduce common configuration header for PXA
PXA: Rename pxa_dram_init to pxa2xx_dram_init
PXA: Squash extern pxa_dram_init()
PXA: Export cpu_is_ and pxa_dram_init functions
PXA: Cleanup Colibri PXA270
PXA: Replace timer driver
PXA: Add cpuinfo display for PXA2xx
PXA: Separate PXA2xx CPU init
PXA: Rename CONFIG_PXA2[57]X to CONFIG_CPU_PXA2[57]X
PXA: Unify vpac270 environment size
PXA: Enable command line editing for vpac270
PXA: Adapt Voipac PXA270 to OneNAND SPL
PXA: Drop Voipac PXA270 OneNAND IPL
PXA: Fixup PXA25x boards after start.S update
PXA: Re-add the Dcache locking as RAM for pxa250
PXA: Rework start.S to be closer to other ARMs
PXA: Drop XM250 board
PXA: Drop PLEB2 board
PXA: Drop CRADLE board
PXA: Drop CERF250 board
Fix regression in SMDK6400
nand: Add common functions to linux/mtd/nand.h
Ethernut 5 board support
net: Armada100: Fix compilation warnings
ARM: remove duplicated code for LaCie boards
ARM: add support for LaCie 2Big Network v2
mvsata: fix ide_preinit for missing disks
netspace_v2: Read Ethernet MAC address from EEPROM
omap3evm: Add support for EFI partitions
part_efi: Fix compile errors
Vadim Bendebury [Mon, 17 Oct 2011 08:36:14 +0000 (08:36 +0000)]
Introduce generic TPM support in u-boot
TPM (Trusted Platform Module) is an integrated circuit and
software platform that provides computer manufacturers with the
core components of a subsystem used to assure authenticity,
integrity and confidentiality.
This driver supports version 1.2 of the TCG (Trusted Computing
Group) specifications.
The TCG specification defines several so called localities in a
TPM chip, to be controlled by different software layers. When
used on a typical x86 platform during the firmware phase, only
locality 0 can be accessed by the CPU, so this driver even while
supporting the locality concept presumes that only locality zero
is used.
This implementation is loosely based on the article "Writing a
TPM Device Driver" published on http://ptgmedia.pearsoncmg.com
Compiling this driver with DEBUG defined will generate trace of
all accesses to TMP registers.
This driver has been tested and is being used in three different
functional ChromeOS machines (Pinetrail and Sandy Bridge Intel
chipsets) all using the same Infineon SLB 9635 TT 1.2 device.
A u-boot cli command allowing access to the TPM was also
implemented and is being submitted as a second patch.
Change-Id: I22a33c3e5b2e20eec9557a7621bd463b30389d73 Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> CC: Wolfgang Denk <wd@denx.de>
projects / u-boot.git / log