SDIO is not supported in u-boot, there is no point in enabling mmc3.
For this purpose, add u-boot specific dtsi that this will be included
automatically while building the dtb.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 17 May 2017 18:06:08 +0000 (14:06 -0400)]
scripts/Makefile.lib: Always have ...-u-boot.dtsi be able to override
The intention of having a -u-boot.dtsi file is to be able to make
changes to the provided upstream dts files as well as to be able to add
nodes. Change the logic for adding the file from making it the last
included file at the top of the dts to being included at the end of the
file.
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Restructure clock manager driver in the preparation to support A10.
Move the Gen5 specific code to _gen5 files.
- Change all uint32_t to u32 and change to use macro BIT(n) for bit shift.
- Check return value from wait_for_bit(). So change return type to int for
cm_write_with_phase() and cm_basic_init().
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Peng Fan [Thu, 13 Apr 2017 06:09:57 +0000 (14:09 +0800)]
imx: mx7dsabresd: enable more DM drivers
Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO
enabled. The 74x164 drivers needs SOFT_SPI and DM_GPIO enabled.
So needs to enable them together.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
Early backports of the imx wdog external reset feature occured before the
property was accepted upstream and used 'ext-reset-output' instead of
'fsl,ext-reset-output'. In order to support older kernels remove both
properties.
Jagan Teki [Sat, 6 May 2017 21:13:03 +0000 (02:43 +0530)]
geam6ul: Add mmc_late_init
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 6 May 2017 21:13:02 +0000 (02:43 +0530)]
geam6ul: Add modeboot env via board_late_init
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 6 May 2017 21:13:01 +0000 (02:43 +0530)]
icorem6: Add mmc_late_init
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 6 May 2017 21:13:00 +0000 (02:43 +0530)]
icorem6: Add modeboot env via board_late_init
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Peng Fan [Tue, 18 Apr 2017 12:41:52 +0000 (20:41 +0800)]
imx: thermal: update imx6 thermal driver according new equation
>From IC guys:
"
After a thorough accuracy study of the Temp sense circuit,
we found that with our current equation, an average part can
read 7 degrees lower than a known forced temperature.
We also found out that the standard variance was around 2C;
which is the tightest distribution that we could create.
We need to change the temp sense equation to center the average
part around the target temperature.
"
Peng Fan [Mon, 10 Apr 2017 11:44:33 +0000 (19:44 +0800)]
net: fec: do not access reserved register for i.MX6ULL
The MIB RAM and FIFO receive start register does not exist on
i.MX6ULL. Accessing these register will cause enet not work well or
cause system report fault.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
Tom Rini [Wed, 17 May 2017 18:13:58 +0000 (14:13 -0400)]
Merge git://git.denx.de/u-boot-uniphier
- Add workaround code to make LD20 SoC boot from ARM Trusted Firmware
- Sync DT with Linux to fix DTC warnings
- Add new SoC support code
- Misc fix, updates
Masahiro Yamada [Tue, 16 May 2017 05:35:15 +0000 (14:35 +0900)]
ARM: uniphier: move kernel physical base to 0x82080000
Reserve enough space below the kernel base.
The assumed address map is: 80000000 - 80ffffff : for IPP 81000000 - 81ffffff : for ARM secure 82000000 - : for Linux
Masahiro Yamada [Mon, 15 May 2017 05:23:46 +0000 (14:23 +0900)]
ARM: dts: uniphier: sync DT with Linux
Fix the following DTC warnings:
Warning (simple_bus_reg): Node /soc/system-bus@58c00000/support_card@1,1f00000/ethernet@00000000 simple-bus unit address format error, expected "0"
Warning (simple_bus_reg): Node /soc/system-bus@58c00000/support_card@1,1f00000/uart@000b0000 simple-bus unit address format error, expected "b0000"
Warning (simple_bus_reg): Node /soc/smpctrl@59800000 simple-bus unit address format error, expected "59801000"
Masahiro Yamada [Fri, 12 May 2017 13:49:02 +0000 (22:49 +0900)]
ARM: uniphier: add weird workaround code for LD20
When booting from ARM Trusted Firmware, U-Boot runs in EL1-NS.
The boot flow is as follows:
BL1 -> BL2 -> BL31 -> BL33 (i.e. U-Boot)
This boot sequence works fine for LD11 SoC (Cortex-A53), but LD20
SoC (Cortex-A72) hangs in U-Boot. The solution I found is to
read sctlr_el1 and write back the value as-is. This should be
no effect, but surprisingly fixes the problem for LD20 to boot.
I do not know why.
Bin Meng [Mon, 8 May 2017 02:52:30 +0000 (19:52 -0700)]
x86: minnowmax: Remove incorrect pad-offset of several pins
Remove 'pad-offset' of soc_gpio_s5_0, soc_gpio_s5_1, soc_gpio_s5_2,
pin_usb_host_en0 and pin_usb_host_en1. These offsets are actually
wrong. Correct value should be added by 0x2000, but since they
are supposed to be 'mode-gpio', 'pad-offset' is not needed at all.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 8 May 2017 02:52:29 +0000 (19:52 -0700)]
x86: ich6_gpio: Add use-lvl-write-cache for I/O access mode
Add a device-tree property use-lvl-write-cache that will cause
writes to lvl to be cached instead of read from lvl before each
write. This is required on some platforms that have the register
implemented as dual read/write (such as Baytrail).
Prior to this fix the blue USB port on the Minnowboard Max was
unusable since USB_HOST_EN0 was set high then immediately set
low when USB_HOST_EN1 was written.
This also resolves the 'gpio clear | set' command warning like:
"Warning: value of pin is still 0"
Signed-off-by: George McCollister <george.mccollister@gmail.com>
<rebased on latest origin/master, fixed all baytrail boards> Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Mon, 24 Apr 2017 07:48:04 +0000 (09:48 +0200)]
spi: ich: Configure SPI BIOS parameters for Linux upon U-Boot exit
This patch adds a remove function to the Intel ICH SPI driver, that will
be called upon U-Boot exit, directly before the OS (Linux) is started.
This function takes care of configuring the BIOS registers in the SPI
controller (similar to what a "standard" BIOS or coreboot does), so that
the Linux MTD device driver is able to correctly read/write to the SPI
NOR chip. Without this, the chip is not detected at all.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Jagan Teki <jteki@openedev.com>
Stefan Roese [Mon, 24 Apr 2017 07:48:03 +0000 (09:48 +0200)]
x86: bootm: Add dm_remove_devices_flags() call to bootm_announce_and_cleanup()
This patch adds a call to dm_remove_devices_flags() to
bootm_announce_and_cleanup() so that drivers that have one of the removal
flags set (e.g. DM_FLAG_ACTIVE_DMA_REMOVE) in their driver struct, may
do some last-stage cleanup before the OS is started.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Mon, 24 Apr 2017 07:48:02 +0000 (09:48 +0200)]
dm: core: Add DM_FLAG_OS_PREPARE flag
This new flag can be added to DM device drivers, which need to do some
final configuration before U-Boot exits and the OS (e.g. Linux) is
started. The remove functions of those drivers will get called at
this stage to do these last-stage configuration steps.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com>
Stefan Roese [Mon, 24 Apr 2017 07:48:01 +0000 (09:48 +0200)]
serial: serial-uclass: Use force parameter in stdio_deregister_dev()
On my x86 platform I've noticed, that calling dm_uninit() or the new
function dm_remove_devices_flags() does not remove the desired device at
all. Debugging showed, that the serial uclass returns -EPERM in
serial_pre_remove(). This patch sets the force parameter when calling
stdio_deregister_dev() resulting in a removal of the device.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Fri, 21 Apr 2017 14:24:47 +0000 (07:24 -0700)]
x86: acpi: Fix Windows S3 resume failure
U-Boot sets up the real mode interrupt handler stubs starting from
address 0x1000. In most cases, the first 640K (0x00000 - 0x9ffff)
system memory is reported as system RAM in E820 table to the OS.
(see install_e820_map() implementation for each platform). So OS
can use these memories whatever it wants.
If U-Boot is in an S3 resume path, care must be taken not to corrupt
these memorie otherwise OS data gets lost. Testing shows that, on
Microsoft Windows 10 on Intel Baytrail its wake up vector happens to
be installed at the same address 0x1000. While on Linux its wake up
vector does not overlap this memory range, but after resume kernel
checks low memory range per config option CONFIG_X86_RESERVE_LOW
which is 64K by default to see whether a memory corruption occurs
during the suspend/resume (it's harmless, but warnings are shown
in the kernel dmesg logs).
We cannot simply mark the these memory as reserved in E820 table
because such configuration makes GRUB complain: unable to allocate
real mode page. Hence we choose to back up these memories to the
place where we reserved on our stack for our S3 resume work.
Before jumping to OS wake up vector, we need restore the original
content there.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Fri, 21 Apr 2017 14:24:44 +0000 (07:24 -0700)]
x86: acpi: Refactor acpi_resume()
To do something more in acpi_resume() like turning on ACPI mode,
we need locate ACPI FADT table pointer first. But currently this
is done in acpi_find_wakeup_vector().
This changes acpi_resume() signature to accept ACPI FADT pointer
as the parameter. A new API acpi_find_fadt() is introduced, and
acpi_find_wakeup_vector() is updated to use FADT pointer as the
parameter as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Fri, 21 Apr 2017 14:24:42 +0000 (07:24 -0700)]
x86: apci: Change PM1_CNT register access to RMW
In enter_acpi_mode() PM1_CNT register is changed to PM1_CNT_SCI_EN
directly without preserving its previous value. Update to change
the register access to read-modify-write (RMW).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Fri, 21 Apr 2017 14:24:41 +0000 (07:24 -0700)]
x86: Adjust board_final_cleanup() order
Call board_final_cleanup() before write_tables(), so that anything
done in board_final_cleanup() on a normal boot path is also done
on an S3 resume path.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Fri, 21 Apr 2017 14:24:40 +0000 (07:24 -0700)]
x86: Do not clear high table area for S3
When SeaBIOS is being used, U-Boot reserves a memory area to be
used for configuration tables like ACPI. But it should not be
cleared otherwise ACPI table will be missing.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Stefan Roese <sr@denx.de>
projects / u-boot.git / log