LPC32xx MAC and clock control configuration requires some minor quirks
to deal with a phy connected by RMII.
It's worth to mention that the kernel and legacy BSP from NXP sets
SUPP_RESET_RMII == (1 << 11) bit, however the description of this bit is
missing in shared LPC32x0 User Manual UM10326 Rev. 3, July 22, 2011
and in LPC32x0 Draft User Mannual Rev. 00.27, November 20, 2008, also
in my tests an SMSC LAN8700 phy device connected over RMII seems to
work correctly without touching this bit.
Add support of RMII, if CONFIG_RMII is defined, this option is aligned
with a number of boards, which already define the same config value.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
net: lpc32xx: improve MAC configuration on reset and initialization
This change rearranges general MAC configuration and PHY specific
configuration of MAC registers (duplex mode and speed), before this
change set bits related to PHY configuration in MAC2 and COMMAND
registers are rewritten by the following writing to the registers.
Without the change auto negotiation on boot quite often is not
completed in reasonable time:
Waiting for PHY auto negotiation to complete......... TIMEOUT !
Additionally MAC1_SOFT_RESET clear bit is removed since it is done in
preceding lpc32xx_eth_initialize() and in lpc32xx_eth_halt(), instead
added missing MCFG_RESET_MII_MGMT on device initialization.
net: lpc32xx: connect MAC to phy with CONFIG_PHY_ADDR id
The lpc32xx_eth_phylib_init() function is capable to connect LPC32XX
MAC to some specified phy by phy id, by chance the single user of
lpc32xx_eth has CONFIG_PHY_ADDR set to 0, however other boards may
have non-zero CONFIG_PHY_ADDR value, fix it.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net: lpc32xx: correct command register reset value
According to LPC32x0 User Manual the following bits in Command
register 0x3106_0100 are defined:
Bit Symbol
2 - Unused
3 RegReset
4 TxReset
5 RxReset
Fix wrong (1-bit shifted right) COMMAND_RESETS value, which sets
an unused bit, but neglects RxReset.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tearing down an unitialized rx channel causes a pending address hole
event to be queued. When booting linux it will report this pending
as something like "Address Hole seen by USB_OTG at address 57fff584",
since u-boot did not handled this interrupt. Prevent that by not
tearing down the rx channel, when not receiving.
Support the 88E1510 PHY which is very similar to the 88E1518.
I also set the INTn output and configured the LEDs.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Hao Zhang <hzhang@ti.com> Cc: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Clemens Gruber [Sat, 6 Jun 2015 12:44:57 +0000 (14:44 +0200)]
net: Improve 88E151x PHY initialization
- The EEE fixup magic should also be enabled for RGMII
- Improved comments
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Hao Zhang <hzhang@ti.com> Cc: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tim Harvey [Tue, 19 May 2015 17:01:20 +0000 (10:01 -0700)]
e1000: remove unnecessary clearing of SWSM.SWSM_SMBI
remove unnecessary clearing of SWSM.SWSM_SMBI when obtaining the SW
semaphore. This was introduced in 951860634fdb557bbb58e0f99215391bc0c29779
while adding i210 support and should be now resolved by releasing the
semaphore when no longer needed.
Cc: Marcel Ziswiler <marcel@ziswiler.com> Cc: Marek Vasut <marex@denx.de> Cc: Aneesh Bansal <aneesh.bansal@freescale.com> Cc: Naveen Burmi <NaveenBurmi@freescale.com> Cc: Po Liu <po.liu@freescale.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Alison Wang <alison.wang@freescale.com> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com> Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com> Cc: York Sun <yorksun@freescale.com> Signed-off-by: Tim Harvey <tharvey@gateworks.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tim Harvey [Tue, 19 May 2015 17:01:18 +0000 (10:01 -0700)]
e1000: releasing semaphore once no longer needed
Once the hwsw semaphore is acquired, it must be released when access to the
hw is completed. Without this subsequent calls to acquire will timeout
obtaining the semaphore.
Cc: Marcel Ziswiler <marcel@ziswiler.com> Cc: Marek Vasut <marex@denx.de> Cc: Aneesh Bansal <aneesh.bansal@freescale.com> Cc: Naveen Burmi <NaveenBurmi@freescale.com> Cc: Po Liu <po.liu@freescale.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Alison Wang <alison.wang@freescale.com> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com> Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com> Cc: York Sun <yorksun@freescale.com> Signed-off-by: Tim Harvey <tharvey@gateworks.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Hans de Goede [Sat, 8 Aug 2015 15:45:18 +0000 (17:45 +0200)]
dm: serial: Add a REQUIRE_SERIAL_CONSOLE option for boards with no serial port
Currently the serial code assumes that there is always at least one serial
port (and panics / crashes due to null pointer dereferences when there is
none).
This makes it impossible to use u-boot on boards where there is no (debug)
serial port, because e.g. all uart pins are muxed to another function.
This commit adds a CONFIG_REQUIRE_SERIAL_CONSOLE Kconfig option, which
defaults to y (preserving existing behavior), which can be set to n on
such boards to make them work.
This commit only implements this for CONFIG_DM_SERIAL=y configs, as allowing
running without a serial port for CONFIG_DM_SERIAL=n configs is non trivial,
and is not necessary at this moment.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Simon Glass <sjg@chromium.org>
Hans de Goede [Mon, 3 Aug 2015 17:45:37 +0000 (19:45 +0200)]
sunxi: display: Add a few extra register and constant defines
Add a few extra sunxi display registers and constant defines.
Also rename some existing defines (e.g. dropping _GCTRL) and make
some more generic (e.g. dropping the 2x scaling from
SUNXI_LCDC_TCON1_TIMING_V_TOTAL).
This is a preparation patch for adding composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Mon, 3 Aug 2015 21:01:38 +0000 (23:01 +0200)]
sunxi: display: Replace #ifdef-ery with helper functions
All the #ifdef-ery in selecting the default and fallback monitor type is
becoming unyielding and makes the code hard to read, replace it with a few
helper functions.
This will also be useful with the upcoming CHIP board which has display
adapter daughterboards which should be runtime detectable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 1 Aug 2015 12:44:29 +0000 (14:44 +0200)]
sunxi: Do not add a stdout-path alias to dts on boards without a serial port
Do not add a bogus (pointing to a non existing serial port) stdout-path
alias to dts on boards without a serial port.
Note that we still define CONS_INDEX as this is used by the SPL where we do
not use DM_SERIAL and thus CONFIG_REQUIRE_SERIAL_CONSOLE is not honored.
We are getting away with this because the sun5i die actually has
an uart0, which in the A13 package is not routed to the outside,
so we are simply sending SPL bootup messages to the tx pin at the
edge of the die, and they go no further from there...
And sofar we only have one A13 board which does not have a serial
port, all others do have a serial port. This kinda makes sense since
the A13 is a much lower pincount package compared to all the other
sunxi SoCs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 8 Jul 2015 14:44:22 +0000 (16:44 +0200)]
sunxi: usb-phy: Never power off the usb ports
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.
Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.
This patch removes the powering off calls, fixing the undesirable power
bouncing.
Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Piotr Zierhoffer [Thu, 23 Jul 2015 12:33:03 +0000 (14:33 +0200)]
sunxi: nand: Add board configuration options
When SPL_NAND_SUNXI option is selected in config, set some configuration
options for sunxi NAND.
This commit also introduces the configurable options in Kconfig.
Signed-off-by: Peter Gielda <pgielda@antmicro.com> Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com> Signed-off-by: Mateusz Holenko <mholenko@antmicro.com> Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com> Signed-off-by: Karol Gugala <kgugala@antmicro.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Piotr Zierhoffer [Thu, 23 Jul 2015 12:33:02 +0000 (14:33 +0200)]
sunxi: nand: Add basic sunxi NAND driver for SPL with DMA support
This driver adds NAND support to SPL.
It was tested on Allwinner A20.
Signed-off-by: Peter Gielda <pgielda@antmicro.com> Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com> Signed-off-by: Mateusz Holenko <mholenko@antmicro.com> Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com> Signed-off-by: Karol Gugala <kgugala@antmicro.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Karol Gugala [Thu, 23 Jul 2015 12:33:01 +0000 (14:33 +0200)]
sunxi: nand: Add pinmux and clock settings for NAND support
To enable NAND flash in sunxi SPL,
pins 0-6, 8-22 and 24 on port C are configured.
Signed-off-by: Karol Gugala <kgugala@antmicro.com> Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Dinh Nguyen [Sat, 1 Aug 2015 01:42:10 +0000 (03:42 +0200)]
arm: socfpga: misc: Add support for printing FPGA type
Add code which uses the new functions for obtaining FPGA ID from
the scan manager. This new code prints the FPGA model attached to
the SoCFPGA during boot and sets environment variable "fpgatype",
which can be used to determine the FPGA model in U-Boot scripts.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com> Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 01:18:50 +0000 (03:18 +0200)]
arm: socfpga: scan: Clean up horrible macros
Clean up the horrible macros present in the scan_manager.h . Firstly,
the function scan_mgr_io_scan_chain_prg() is static, yet all the macros
are used only within it, thus there is no point in having them in the
header file. Moreover, the macros are just making the code much less
readable, so remove them instead.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce generic function for accessing the JTAG scan chains in the
SCC manager. Make use of this function throughout the SCC manager to
replace the ad-hoc writes to registers and make the code less cryptic.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sat, 1 Aug 2015 00:48:03 +0000 (02:48 +0200)]
arm: socfpga: scan: Clean up scan_chain_engine_is_idle()
Rework this function so it's clear that it is only polling for certain
bits to be cleared. Add kerneldoc. Fix it's return value to be either
0 on success and -ETIMEDOUT on error and propagate this through the
scan manager code.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
board/altera/socfpga/wrap_sdram_config.c:245:26: error: ‘RW_MGR_MEM_NUMBER_OF_RANKS’ undeclared here (not in a function)
make[2]: *** [spl/board/altera/socfpga/wrap_sdram_config.o] Error 1
Marek Vasut [Sun, 2 Aug 2015 17:47:01 +0000 (19:47 +0200)]
ddr: altera: sequencer: Clean checkpatch issues
Fix most of the dangling checkpatch issues, no functional change.
There are still 7 warnings, 1 checks , but those are left in place
for the sake of readability of the code.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 17:26:55 +0000 (19:26 +0200)]
ddr: altera: sequencer: Pluck out misc macros from code
Actually convert the sequencer code to use socfpga_sdram_misc_config
instead of the various macros. This is just an sed exercise here, no
manual coding needed.
This patch actually removes the need to include any board-specific
files in sequencer.c , so sequencer.c namespace is now no longer
poluted by QTS-generated macros.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This is another macro used to obfuscate the real code. The
T(INIT|RESET)_CNTR._VAL is always defined, so this indirection
is unnecessary. Get rid of this.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_misc_config to wrap the remaining
misc configuration values in board file. Again, introduce a function,
socfpga_get_sdram_misc_config(), which returns this the structure. This
is almost the final step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 17:10:58 +0000 (19:10 +0200)]
ddr: altera: sequencer: Pluck out IO_* macros from code
Actually convert the sequencer code to use socfpga_sdram_io_config
instead of the IO_* macros. This is just an sed excercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 17:00:23 +0000 (19:00 +0200)]
ddr: altera: sequencer: Wrap IO_* macros
Introduce structure socfpga_sdram_io_config to wrap the IO configuration
values in board file. Introduce socfpga_get_sdram_io_config() function,
which returns this the structure. This is another step toward wrapping
the nasty QTS generated macros in board files and reducing the pollution
of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 16:44:06 +0000 (18:44 +0200)]
ddr: altera: sequencer: Pluck out RW_MGR_* macros from code
Actually convert the sequencer code to use socfpga_sdram_rw_mgr_config
instead of the RW_MGR_* macros. This is just an sed exercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 16:12:08 +0000 (18:12 +0200)]
ddr: altera: sequencer: Wrap RW_MGR_* macros
Introduce structure socfpga_sdram_rw_mgr_config to wrap the RW manager
configuration values in board file. Introduce a complementary function,
socfpga_get_sdram_rwmgr_config(), which returns this the structure.
This is another step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 15:15:19 +0000 (17:15 +0200)]
ddr: altera: sequencer: Wrap ac_rom_init and inst_rom_init
Introduce two wrapper functions, socfpga_get_seq_ac_init() and
socfpga_get_seq_inst_init() to avoid direct inclusion of the
sequencer_auto_ac_init.h and sequencer_auto_inst_init.h QTS
generated files. This reduces namespace pollution again.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sat, 1 Aug 2015 21:12:11 +0000 (23:12 +0200)]
ddr: altera: sdram: Make sdram_start and sdram_end into u32
Originally, both sdram_start and sdram_end were 64b values. The
sdram_start had no reason for being so, since our address space
is only 32b, so switching sdram_start to u32 is simple.
The sdram_end is a bit more complex, since it can actually be
set to (1 << 32) if someone really wanted to use an SoCFPGA with
4 GiB of DRAM and fixed the code around a little. But, the code
handling the protection rules internally decrements the sdram_end
variable anyway. Thus, instead of calling the code and passing in
the address of the SDRAM end, pass in the address already decremented
by one. This lets the sdram_end be 32b as well.
Marek Vasut [Sat, 1 Aug 2015 20:26:11 +0000 (22:26 +0200)]
ddr: altera: sdram: Clean up sdram_write_verify()
Clean the function up so that it's obvious what it is doing,
fix the formating strings in debug outputs, add kerneldoc.
Make the function return proper errno-compliant return values
and propagate this change throughout sdram.c
Marek Vasut [Sat, 1 Aug 2015 19:47:16 +0000 (21:47 +0200)]
ddr: altera: sdram: Clean up sdram_calculate_size() part 2
Clean up coding style, mostly clean up comments, add kerneldoc.
Also, zap assignment of the "cs" variable, which is outright
dead code, so just remove it.
Marek Vasut [Sat, 1 Aug 2015 19:44:00 +0000 (21:44 +0200)]
ddr: altera: sdram: Clean up sdram_calculate_size() part 1
Pluck out all of the CONFIG_HPS_SDR_CTRLCFG_* macros. This change
makes sdram.c completely clear of these macros and allows removing
of the ugly include of sdram.h . The namespace is now a much nicer
place!
Introduce socfpga_sdram_get_config() function implement in a board file,
which returns the socfpga_sdram_config structure. This is the last step
in cleaning up the socfpga_mmr_init_full(), but not the last step which
allows removing the inclusion of sdram.h from drivers/ddr/altera/sdram.c
thus far.
Marek Vasut [Sat, 1 Aug 2015 19:24:31 +0000 (21:24 +0200)]
ddr: altera: sdram: Clean up sdram_mmr_init_full() part 5
Rework remaining two register setting functions such that they only
return the final register value. Move the register setting into the
block of register I/O in sdram_mmr_init_full().
Marek Vasut [Sat, 1 Aug 2015 19:21:21 +0000 (21:21 +0200)]
ddr: altera: sdram: Clean up sdram_mmr_init_full() part 4
Merge sdr_set_*() functions which are just setting registers among
the sea of register setting in sdram_mmr_init_full(). There is no
need to keep them separate this way, there is nothing special about
them.
Marek Vasut [Sat, 1 Aug 2015 18:58:44 +0000 (20:58 +0200)]
ddr: altera: sdram: Clean up sdram_mmr_init_full() part 2
Suck out all the CONFIG_HPS_SDR_CTRLCFG_* from sdram_mmr_init_full()
into the socfpga_sdram_config structure. There is still one ugly
macro left behind, but this will be taken care of in subsequent patch.
Introduce this seemingly massive structure, which holds required values
of all the registers of the SDRAM controller. The idea here is to avoid
including the sdram.h header file, which is full of ad-hoc macros that
polute the global namespace. Once the cleanup of sdram.c would be complete
and all registers would be loaded from this new socfpga_sdram_config, a
board file will only pass this structure into the sdram.c . This will
hide all the horrors generated by QTS in the board directory.
Marek Vasut [Sat, 1 Aug 2015 17:45:24 +0000 (19:45 +0200)]
ddr: altera: sdram: Clean up set_sdr_dram_timing*()
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Merge set_sdr_dram_timing{1,2,3,4,lowpwr}() into single function
set_sdr_dram_timing() , since there's no point in keeping all this
stuff separate anymore.
Marek Vasut [Sat, 1 Aug 2015 17:33:40 +0000 (19:33 +0200)]
ddr: altera: sdram: Clean up set_sdr_ctrlcfg()
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
The big plan here is to remove all the CONFIG_HPS_SDR_ macros, hide
them in QTS compatibility layer in board implementation and pass only
a small structure into the driver.
Marek Vasut [Sat, 1 Aug 2015 17:20:19 +0000 (19:20 +0200)]
ddr: altera: sdram: Clean up compute_errata_rows() part 2
Remove all parameters of this function, since they are only constants
passed in from another function, so make them local. Also, rename the
function to get_errata_rows() as this is closer to what it does.
Marek Vasut [Mon, 3 Aug 2015 16:31:51 +0000 (18:31 +0200)]
arm: socfpga: Add temporary workaround for missing SD/MMC patches
Add a small workaround into the platform code which forces the SDMMC
into 8-bit mode (the default configuration for all socfpga platforms)
to work around breakage caused by missing patches in mainline which
switch the probing of SD/MMC to OF instead of static configuraiton.
The patches will hit mainline after the SPL series, so to avoid build
issues, add this small temporary workaround.
Marek Vasut [Sat, 18 Jul 2015 03:58:44 +0000 (05:58 +0200)]
ddr: altera: Clean up rw_mgr_mem_calibrate_vfifo_end()
This function is implementing the DDR calibration Stage 3 as
described in Altera EMI_RM 2015.05.04 . The main body of this
function is almost identical to Stage 1.3 (DQ/DQS centering)
for all but two flags -- use_read_test and update_fom. Convert
this function to call rw_mgr_mem_calibrate_dq_dqs_centering()
with the correct flags set to trim down the code duplication.
Moreover, reorder the remnants in the function a little and
convert the function to return either 0 or -EIO in case of
success and failure respectively, to match the common return
value convention.
Marek Vasut [Sat, 18 Jul 2015 18:44:28 +0000 (20:44 +0200)]
ddr: altera: Clean up rw_mgr_mem_calibrate_vfifo_center() part 10
Fix the return value of the function to match common convention
where 0 means success and negative means error. Fix the return
values in case of an error to use errno.h codes.
Marek Vasut [Sat, 18 Jul 2015 18:42:27 +0000 (20:42 +0200)]
ddr: altera: Clean up rw_mgr_mem_calibrate_vfifo_center() part 9
The read_group and write_group arguments are the same in all
cases when this function is invoked, just merge them into one
rw_group argument. Also, clean up the function argument data
types and constify them.
Marek Vasut [Sat, 18 Jul 2015 18:34:00 +0000 (20:34 +0200)]
ddr: altera: Clean up rw_mgr_mem_calibrate_vfifo_center() part 8
The search_stop_check() always resets the bit_chk to a new value,
so bit_chk will never survive between search_left_edge() and
search_right_edge() invocation. There is thus no need to pass
it into these functions, so make bit_chk local to them.
projects / u-boot.git / log