Michael Walle [Thu, 17 Nov 2011 12:52:29 +0000 (12:52 +0000)]
mvgbe: remove setting of ethaddr within the driver
A network driver should not touch the environment at all. This patch fixes
this behaviour by removing the code for setting a default/randomized MAC
address.
Signed-off-by: Michael Walle <michael@walle.cc> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Eric Cooper <ecc@cmu.edu> Cc: Jason Cooper <u-boot@lakedaemon.net> Cc: Siddarth Gore <gores@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Simon Guinot <simon.guinot@sequanux.org> Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Gabe Black [Mon, 5 Dec 2011 12:09:27 +0000 (12:09 +0000)]
x86: Add support for specifying an initrd with the zboot command
This change finishes plumbing the initrd support built into the zboot
mechanism out to the command interface.
It also fixes a bug in the command declaration where the kernel size could
be passed as an optional second parameter but not enough arguments were
allowed.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Gabe Black [Mon, 5 Dec 2011 12:09:26 +0000 (12:09 +0000)]
x86: Refactor the zboot innards so they can be reused with a vboot image
If vboot successfully verifies a kernel, it will leave it in place and
basically ready to boot. The zeropage table which is part of the x86 boot
protocol is at the end of the kernel, though, instead of the beginning, and
because the image is already in place there's no need to copy it around.
This change refactors the code which implements the zboot command so that
the configuration of the zeropage table and loading the pieces of the
kernel into memory are done separately. Also, because the command line goes
before the zeropage table in vboot which is somewhat incompatible with the
normal protocol, where to put the command line is a now a parameter instead
of being hard coded.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Gabe Black [Mon, 5 Dec 2011 12:09:25 +0000 (12:09 +0000)]
x86: Add infrastructure to extract an e820 table from the coreboot tables
Also approximate the size of RAM using the largest RAM address available
in the tables. There may be areas which are marked as reserved which are
actually at the end of RAM.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Gabe Black [Mon, 5 Dec 2011 12:09:24 +0000 (12:09 +0000)]
x86: Add support for booting Linux using the 32 bit boot protocol
This change conditionally modifies the zboot command so that it can use the
32 bit boot protocol. This is necessary because the 16 bit realmode entry
point assumes that it can call BIOS services which neither coreboot nor
u-boot provide.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Gabe Black [Mon, 5 Dec 2011 12:09:23 +0000 (12:09 +0000)]
x86: Clean up the x86 zimage code in preparation to extend it
This change cleans up some formatting issues in the zimage handling code, and
converts it from using offsets added to a base pointer to using the available
structure definitions which were already being included.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Gabe Black [Mon, 5 Dec 2011 12:09:22 +0000 (12:09 +0000)]
x86: Import code from coreboot's libpayload to parse the coreboot table
This change also forces the lib_sysinfo structure to be in the .data
section. Otherwise it ends up in the .bss section. U-boot assumes that it
doesn't need to copy it over during relocation, and instead fills that
whole section with zeroes. If we really were booting from ROM that would be
appropriate, but we need some information from the coreboot tables (memory
size) before then and have to fill that structure before relocation. We
skirt u-boot's assumption by putting this in .data where it assumes there
is still read only but non-zero data.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Gabe Black [Tue, 29 Nov 2011 18:05:07 +0000 (18:05 +0000)]
x86: Initial commit for running as a coreboot payload
Add a target for running u-boot as a coreboot payload in boards.cfg, a
board, CPU and a config. This is a skeleton implementation which always
reports the size of memory as 64 MB.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Andreas Bießmann [Thu, 15 Dec 2011 08:56:55 +0000 (09:56 +0100)]
avr32:mmu.c: fix printf() length modifier
avr32 uses unsigned long addresses, fix the printf() length modifier for that
fact.
Before this patch following warning occours:
---8<---
mmu.c: In function 'mmu_init_r':
mmu.c:25: warning: format '%08x' expects type 'unsigned int', but argument 2 has type 'uintptr_t'
--->8---
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
cc: Mike Frysinger <vapier@gentoo.org>
cc: Thomas Chou <thomas@wytron.com.tw>
cc: Reinhard Meyer <u-boot@emk-elektronik.de> Acked-by: Mike Frysinger <vapier@gentoo.org>
Andreas Bießmann [Thu, 15 Dec 2011 08:56:54 +0000 (09:56 +0100)]
fat.c: fix printf() length modifier
The DIRENTSPERBLOCK utilizes sizeof() which will return a size_t which has no
fixed size. Therefor use correct length modifer for printf() statement to
prevent compiler warnings.
This patch fixes following warning:
---8<---
fat.c: In function 'do_fat_read':
fat.c:879: warning: format '%d' expects type 'int', but argument 4 has type 'long unsigned int'
--->8---
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
cc: Mike Frysinger <vapier@gentoo.org>
cc: Thomas Chou <thomas@wytron.com.tw>
cc: rjones@nexus-tech.net
cc: kharris@nexus-tech.net Acked-by: Mike Frysinger <vapier@gentoo.org>
Andreas Bießmann [Thu, 15 Dec 2011 08:56:53 +0000 (09:56 +0100)]
cmd_sf.c: fix printf() length modifier
size_t is not always 'unsigned int', use corret length modifer.
This patch fixes following warning:
---8<---
cmd_sf.c: In function 'spi_flash_update_block':
cmd_sf.c:130: warning: format '%#x' expects type 'unsigend int', but argument 4 has type 'size_t'
cmd_sf.c:135: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'size_t'
--->8---
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
cc: Mike Frysinger <vapier@gentoo.org>
cc: Thomas Chou <thomas@wytron.com.tw> Acked-by: Mike Frysinger <vapier@gentoo.org>
Sonny Rao [Mon, 10 Oct 2011 09:22:31 +0000 (09:22 +0000)]
Make printf and vprintf safe from buffer overruns
From: Sonny Rao <sonnyrao@chromium.org>
utilize the added vscnprintf functions to avoid buffer overruns
The implementation is fairly dumb in that it doesn't detect
that the buffer is too small, but at least will not cause crashes.
Sonny Rao [Wed, 2 Nov 2011 09:52:08 +0000 (09:52 +0000)]
Add safe vsnprintf and snprintf library functions
From: Sonny Rao <sonnyrao@chromium.org>
These functions are useful in U-Boot because they allow a graceful failure
rather than an unpredictable stack overflow when printf() buffers are
exceeded.
Mostly copied from the Linux kernel. I copied vscnprintf and
scnprintf so we can change printf and vprintf to use the safe
implementation but still return the correct values.
(Simon Glass <sjg@chromium.org> modified this commit a little)
Kyle Moffett [Fri, 16 Dec 2011 11:14:40 +0000 (11:14 +0000)]
tools/setlocalversion: Update from the Linux Kernel
Several bugfixes have occurred upstream since this script was imported
into U-Boot. In particular, the script currently in U-Boot does not
describe commit f8bbb4dad0e9d91b7a51d6cc54dcf66d142f50fe correctly,
resulting in a version of "2011.09" instead of "2011.09-01460-gf8bbb4d".
With that commit checked out, the command "git name-rev --tags HEAD"
gives this result:
HEAD tags/v2011.12-rc1~30^2
Then the "changes" regex does not match because of the trailing '^2':
grep -E '^HEAD[[:space:]]+(.*~[0-9]*|undefined)$'
The new version of tools/setlocalversion in the kernel correctly handles
those situations by using different plumbing commands.
The version from the kernel is not directly usable as it does not append
the full GIT version that U-Boot expects unless the right config options
are set (CONFIG_LOCALVERSION_AUTO=y). Other than a few minor changes
for Kconfig, the imported version is very similar to Linux v3.2-rc4.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Sat, 17 Dec 2011 19:51:16 +0000 (20:51 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
* 'master' of git://git.denx.de/u-boot-usb:
USB: Use (get|put)_unaligned for accessing wMaxPacketSize
usb:gadget:s5p Enable the USB Gadget framework at Exynos4210 (C210 Universal)
README: add documentation for CONFIG_USB_ULPI*
USB: ULPI: increase error case verbosity
USB: ULPI: clean a mixup of return types
USB: ULPI: switch argument type from u8 to unsigned
Tom Rini [Thu, 15 Dec 2011 15:40:51 +0000 (08:40 -0700)]
USB: Use (get|put)_unaligned for accessing wMaxPacketSize
In 9792987721c7980453fe6447c3fa6593b44f8458 Stefan describes a usecase
where the previous behavior of leaving wMaxPacketSize be unaligned
caused fatal problems. The initial fix for this problem was incomplete
however as it showed another cases of non-aligned access that previously
worked implicitly. This switches to making sure that all access of
wMaxPacketSize are done via (get|put)_unaligned.
In order to maintain a level of readability to the code in some cases
we now use a variable for the value of wMaxPacketSize and in others, a
macro.
Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Remy Bohmer <linux@bohmer.net>
OpenRISC: Tested-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Beagleboard xM, Pandaboard run-tested, s5p_goni build-tested. Signed-off-by: Tom Rini <trini@ti.com>
Jerry Huang [Thu, 17 Nov 2011 02:15:38 +0000 (10:15 +0800)]
powerpc/mpc83xx: set TXEQA/TXEQE value for mpc837XE sata
In the current u-boot code, the value of these fields are the reserved
value (0b100), through the signal integrity measurement on freescale's
board with these reserved setting, the signal eye is out of the recommended
spec for non-transition amplitude at 500mV nominal.
According to the errata for MPC8379E, we should make a change to the
recommended setting from essentially nothing at this time to 0b001 for SATA.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Wolfgang Denk [Mon, 12 Dec 2011 13:51:16 +0000 (14:51 +0100)]
Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-staging
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
pm9g45: init serial console before relocation
pm9261: init serial console before relocation
pm9263: init serial console before relocation
Fix:
reiserfs.c: In function 'reiserfs_mount':
reiserfs.c:360:22: warning: dereferencing type-punned pointer
will break strict-aliasing rules [-Wstrict-aliasing]
Fix:
../common/isa.c: In function 'handle_isa_int':
../common/isa.c:385:21: warning: variable 'isr2' set but not used
[-Wunused-but-set-variable]
../common/isa.c:385:16: warning: variable 'isr1' set but not used
[-Wunused-but-set-variable]
Signed-off-by: David Mueller <d.mueller@elsoft.ch>
Kumar Gala [Wed, 7 Dec 2011 04:42:58 +0000 (04:42 +0000)]
powerpc/bootm: Flush ramdisk and device tree image when booting on MP
We already flush the kernel image after we've loaded it to ensure
visiblity to the other cores. We need to do the same thing for the
ramdisk and device tree images. In AMP boot scenarios we might not be
HW cache coherent with the secondary core that we are loading and
setting the ramdisk and device tree up for. Thus we need to ensure
we've flushed the regions of memory utilized by ramdisk and device tree
so the loadding and any modifications (from decompression or fdt updates)
are made visible to the secondary cores.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Switch to extension board detection using pci_find_device()
instead of detecting by i2c access to EEPROM device on
extension board.
This is a cleaner detection method since EEPROM addresses
can be different on different board revisions. This also
avoids "i2c_read: failed to address chip" error messages
in the boot log on boards without extension board which
may confuse users.
Wolfgang Denk [Mon, 12 Dec 2011 06:58:58 +0000 (07:58 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
* 'master' of git://git.denx.de/u-boot-usb:
USB: efikamx: Enable USB on EfikaMX and EfikaSB
USB: Add generic ULPI layer and a viewport
USB: EHCI: Allow EHCI post-powerup configuration in board files
USB: mx51evk: add end enable USB host support on port 1
USB: mx53loco: add end enable USB host support on port 1
USB: MX5: Add MX5 usb post-init callback
USB: MX5: Abstract out mx51 USB pixmux configuration
USB: MX5: add generic USB EHCI support for mx51 and mx53
USB: MX5: add helper functions to enable USB clocks
usb:gadget:s5p Enable the USB Gadget framework at GONI
usb:gadget:s5p USB Device Controller (UDC) implementation
ehci: speed up initialization
usb: add help for missing start subcommand
cosmetic: remove excess whitespace from usb command help
usb: align usb_endpoint_descriptor to 16-bit boundary
usbtty: init endpoints prior to startup events
pxa: convert pxa27x_udc to use read and write functions
pxa: activate the first usb host port on pxa27x by default
pxa: fix usb host register mismatch
ehci-fsl: correct size of ehci caplength
USB: Add usb_event_poll() to get keyboards working with EHCI
USB: gadaget: add Marvell controller support
USB: Fix complaints about strict aliasing in OHCI-HCD
USB: Drop dead code from usb_kbd.c
USB: Rework usb_kbd.c
USB: Add functionality to poll the USB keyboard via control EP
Wolfgang Denk [Mon, 12 Dec 2011 06:56:41 +0000 (07:56 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
arm: add __aeabi_unwind_cpp_pr1() function to avoid linker complaints
post: fix compile issue for post tests on kirkwood
Marek Vasut [Fri, 24 Jun 2011 19:46:07 +0000 (21:46 +0200)]
USB: efikamx: Enable USB on EfikaMX and EfikaSB
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com>
Jana Rapava [Mon, 5 Dec 2011 09:07:00 +0000 (11:07 +0200)]
USB: Add generic ULPI layer and a viewport
Add partial ULPI specification implementation that should be enough to
interface the ULPI PHYs in the boot loader context.
Add a viewport implementation for Chipidea/ARC based controllers.
Signed-off-by: Jana Rapava <fermata7@gmail.com> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Cc: Remy Bohmer <linux@bohmer.net> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Simon Glass <sjg@chromium.org>
Marek Vasut [Mon, 11 Jul 2011 00:37:01 +0000 (02:37 +0200)]
USB: EHCI: Allow EHCI post-powerup configuration in board files
This patch allows USB to work on some hosts, which need additional frobing after
the host was powered up via regular USB powerup sequence.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com>
USB: mx51evk: add end enable USB host support on port 1
Signed-off-by: Wolfgang Grandegger <wg@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com>
USB: mx53loco: add end enable USB host support on port 1
Signed-off-by: Wolfgang Grandegger <wg@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com>
Marek Vasut [Thu, 24 Nov 2011 04:14:00 +0000 (05:14 +0100)]
USB: MX5: Add MX5 usb post-init callback
This is useful for USB Transceivers init etc.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com>
Marek Vasut [Thu, 24 Nov 2011 03:22:17 +0000 (04:22 +0100)]
USB: MX5: Abstract out mx51 USB pixmux configuration
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com>
USB: MX5: add generic USB EHCI support for mx51 and mx53
It's derived from ehci-mxc and uses the header files of the
ehci-fsl interface. The callback board_ehci_hcd_init() has
been introduced to allow for board-specific setup when USB
is started.
USB: MX5: add helper functions to enable USB clocks
Signed-off-by: Wolfgang Grandegger <wg@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com>
V2: Fix spacing in crm_regs.h
Vincent Palatin [Mon, 5 Dec 2011 22:52:22 +0000 (14:52 -0800)]
ehci: speed up initialization
According to EHCI specification v1.0, the controller should stabilize
the power on a port at most 20 ms after the port power bit transition.
So, we put this setting in the virtual descriptor corresponding field,
(bPwrOn2PwrGood = 10 => 10 x 2ms = 20ms), this saves about 500ms at each
controller initialization/enumeration.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
usb: align usb_endpoint_descriptor to 16-bit boundary
The usb_endpoint_descriptor struct is 7 bytes large and is
defined as an array (ep_desc[USB_MAXENDPOINTS])
in the usb_interface struct in include/usb.h
This fact will result in that every odd index in that
array will start at an uneven address, this in
turn makes accesses to u16 wMaxPacketSize unaligned.
Such accesses are illegal on the OpenRISC architecture
(as well as other architectures) and will render a bus error.
Setting the aligned(2) attribute on usb_endpoint_descriptor
will force wMaxPacketSize to a 16-bit boundary.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Marek Vasut [Mon, 10 Oct 2011 15:34:27 +0000 (17:34 +0200)]
USB: Drop dead code from usb_kbd.c
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Denk <wd@denx.de>
Marek Vasut [Mon, 10 Oct 2011 15:34:26 +0000 (16:34 +0100)]
USB: Rework usb_kbd.c
* Support dynamic allocation of devices
* Passing data via usb device privptr
* Reorder functions to avoid forward declarations
* Introduce generic polling mechanism to fix musb and ehci-hcd breakage
due to using "extern new;" to access keyboard driver data!
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Denk <wd@denx.de>
Marek Vasut [Sun, 25 Sep 2011 19:00:37 +0000 (20:00 +0100)]
USB: Add functionality to poll the USB keyboard via control EP
This allows the keyboard to avoid requests via Interrupt Endpoint altogether and
run all requests via Control Endpoint. This uses the Get_Report request.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Remy Bohmer <linux@bohmer.net>
Rebased on current code.
This patch fixes the issue similar to commit d442b6e7ad6a86e2fd0e6297291fe8872ff26fc6 but I don't know if it's
general enough or if it does harm when using other toolchains.
Holger Brunck [Thu, 24 Nov 2011 03:09:10 +0000 (03:09 +0000)]
post: fix compile issue for post tests on kirkwood
commit f31a911fe (arm, post: add missing post_time_ms for arm)
enables get_ticks and get_tbclk for all arm based boards,
but kirkwood has currently no implementation for this. So
undefine this for kirkwood boards.
U-boot itself generally builds with -nostdinc. This is because the
bootloader needs to be completely standalone. In the sandbox arch
though, we need a little bit of code to glue the u-boot world to the
host operating system, and we need to be able to access the host
libc's headers in order to do so.
Currently, we're using -I/usr/include to workaround the global
-nostdinc, but that doesn't work for everyone and for all headers.
Instead, let's filter out -nostdinc when building the os.c code.
Without this patch, some distros hit errors such as:
---8<---
In file included from /usr/include/fcntl.h:27:0,
from os.c:22:
/usr/include/features.h:323:26: fatal error:
bits/predefs.h: No such file or directory
--->8---
Signed-off-by: Andreas Bießmann <biessmann@corscience.de> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Tom Rini <trini@ti.com> Cc: Heiko Schocher <hs@denx.de> Cc: Wolfgang Denk <wd@denx.de>
arm, davinci: Use lldiv for the 64-bit divisions in timer.c
Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Tom Rini <trini@ti.com> Cc: Heiko Schocher <hs@denx.de> Cc: Wolfgang Denk <wd@denx.de>
Fix:
flash.c: In function 'flash_get_offsets':
flash.c:122:10: warning: variable 'pOrgDef' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'flash_erase':
flash.c:263:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:439:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Dave Peverley <dpeverley@mpc-data.co.uk> Acked-by: Tom Rini <trini@ti.com>
projects / u-boot.git / log