sh: define CONFIG_DISPLAY_BOARDINFO to print board information
All SH boards define a checkboard() function which outputs basic board
information on boot, however generic board support requires to define
CONFIG_DISPLAY_BOARDINFO to do that, so define it for the boards.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
sh: remove undefined DEBUG preprocessor token from board config files
By default this undef is a noop, moreover at this point when the
platform support is broken is prevents debugging of U-boot by manual
insertion of #define DEBUG into common files, so it makes sense to
remove the option from all SH boards as a harmful one.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
At the moment in runtime all defined sections are copied into or
created in RAM, specify this explicitly to assert potential out of RAM
placements of the sections.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
sh: define entry point and reloc_dst inside a linker script
No functional change, concentrate linker script commands in one
place for convenience. Entry point is set to CONFIG_SYS_TEXT_BASE by
default on build, so this option can be omitted from being added to
the linker script.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
sh: place board lowlevel_init code in the beginning of .text
Reference lowlevel_init of all supported SH2A/SH3/SH4/SH4A boards
from a shared linker script, the lowlevel_init function will be called
by a relative address.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
sh4: use single u-boot linker script for all boards
Three supported SH4/SH4A boards with the bootloader image stored on
SPI flash have own flavour of a linker script, in turn they are equal
among each other. The only difference is that the text from
lowlevel_init.o is placed right after start.o, which makes sense.
Note that .bss section is not marked as NOLOAD, because for about
10 years this is a default option of a GNU linker, either the
attribute is found or not the resulting image file is the same.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Since a platform conversion to generic board support has not been
accomplished some architecture specific bits are missing from board_f
init sequence, the change adds a number of basic expected callbacks
into early init sequence.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_RTL8139 was moved to a board defconfig by a commit 86e9dc86b1a2
("net: Move CONFIG_RTL8139 to Kconfig"), however it was done
incorrectly due to a missing CONFIG_NETDEVICES selection, thus
virtually it was just a removal of the driver compilation.
As an unlucky consequence the option was completely removed by a purge
commit adad96e60d0e ("configs: Re-sync HUSH options"), restore the
driver inclusion back.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
r2dplus: use P1 area space for text base and PCI system memory
While both options are acceptable use P1 area physical addresses
instead of external memory space of text base and PCI system memory
for unification purposes, all other supported superh boards have the
same selection.
This allows to easily ensure that CONFIG_SYS_TEXT_BASE is located
within available DRAM.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
For ease of use and accounting a condition that on SH4
pci_phys_to_bus() and pci_bus_to_phys() are one in one mappings due to
unimplemented __iomem() conversion, this change fixes access to SDRAM
memory by PCI devices.
This change also generalizes PCI system memory configuration, which is
taken from board specific defines rather than hardcoded in the PCI
host driver.
The change actually maps PCI I/O window to the same address on PCI bus
as it is stated by a comment, before the change transfers to the PCI I/O
space are failed due to misconfiguration of the most significant 14 bits
of the PCI address in PCIIOBR (note that it is set to 0x0).
Most probably the problem remained unnoticed, because communcation
to all tested PCI devices is done over PCI memory space only.
sh4: cache: move exported cache manipulation functions into cache.c
No functional change, moving cache manipulation functions into cache.c
allows to collect all of them in a single location and as a pleasant
side effect cache_control() function can be unexported now.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
cache_wback_all() is a local function and it is called from
cache_control() only, which is in turn jumps to P2 area.
The change fixes an issue when cache_wback_all() returns from P2 to
P1, however cache_control() continues to manipulate with CCR
register, according to the User's Manual this is restricted.
The change is similar to commit 994b56616bae ("sh: delete an unused
source file") for SH2, however here the removed cache.c file was
built and included into an image as a dead code.
If it is needed in future the contents can be reused from a similar
arch/sh/cpu/sh4/cache.c file, which is in turn will be moved to
a shared among all core flavours location at arch/sh/lib/cache.c.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
sh4: cache: correct flush_cache() to writeback and invalidate
In common usecases flush_cache() assumes both cache invalidation and
write-back to memory, instead of doing cache invalidation only with
the wrapped 'ocbi' instruction pin flush_cache() to cache invalidation
with memory write-back done by 'ocbp'.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
sh4: cache: correct dcache flush to invalidate with write-back
In common usecases flush_cache() assumes both cache invalidation and
write-back to memory, thus in flush_dcache_range() implementation
change SH4 cache write-back only instruction 'ocbwb' with cache purge
instruction 'ocbp', according to the User's Manual there should be no
performance penalty for that.
Note that under circumstances only cache invalidation is expected from
flush_cache() call, in these occasional cases the current version of
flush_cache() works, which is a wrapper over invalidate_dcache_range()
at the moment, this will be fixed in the following change.
Jonathan Gray [Sat, 26 Nov 2016 04:18:00 +0000 (15:18 +1100)]
compiler.h: use u-boot endian macros on OpenBSD
When building u-boot on sparc64 and powerpc hosts it became clear that
u-boot expects endian conversion defines to be macros:
lib/crc32.c:87: error: braced-group within expression allowed only inside a function
For OpenBSD switch from using system definitions equivalent to the u-boot ones
and define glibc __BYTE_ORDER __BIG_ENDIAN __LITTLE_ENDIAN names, as at least
some parts of the non-cross build assumes those names are present (ie crc32.c).
Michal Simek [Wed, 30 Nov 2016 11:50:58 +0000 (12:50 +0100)]
scsi: Separate SCSI private block description initialization
When blk_create_device() is called some parameters in blk_desc are
automatically filled. Separate SCSI private initialization and SCSI full
block device initialization not to rewrite already prepared data.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Wed, 30 Nov 2016 11:12:31 +0000 (12:12 +0100)]
scsi: Change scsi_scan() to be able to return value
With DM_SCSI this function will return more than one return value to
cover errors.
Suggested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Fri, 18 Nov 2016 15:22:42 +0000 (16:22 +0100)]
scsi: Simplify scsi_read/scsi_write()
There is no reason to directly point to static allocated array
when we have proper block_dev pointer available via parameter
in !CONFIG_BLK. For CONFIG_BLK this is read directly from uclass
platdata.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Wed, 16 Nov 2016 07:41:01 +0000 (08:41 +0100)]
common: miiphyutil: Work and report phy address in hex in mdio cmd
It is confusing that mdio commands work and report phy id as
decimal value when mii is working with hex values.
For example:
ZynqMP> mdio list
gem:
21 - TI DP83867 <--> ethernet@ff0e0000
ZynqMP> mdio read ethernet@ff0e0000 0
Reading from bus gem
PHY at address 21:
0 - 0x1140
ZynqMP> mii dump 21 0
Incorrect PHY address. Range should be 0-31
...
ZynqMP> mii dump 15
0. (1140) -- PHY control register --
(8000:0000) 0.15 = 0 reset
U-Boot normally takes hex values that's why this patch is changing mdio
command to handle hex instead of changing mii command to handle decimal
values.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Michal Simek [Wed, 26 Oct 2016 07:24:32 +0000 (09:24 +0200)]
ARM64: zynqmp: List secondary software boot modes
Using alternative bootmode field to support automatic secondary boot
modes. It is purely software setting where SW modes are using free
bootmode combinations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 29 Nov 2016 11:03:51 +0000 (12:03 +0100)]
ARM64: zynqmp: Use DTS name for different psu_init_gpl* files in SPL
CONFIG_SYS_CONFIG_NAME is not proper config option for different low
level init files because different board revisions requires different
psu_init_gpl* files.
Also at the end of moving drivers to DM all board specific configuration
files should be removed.
Michal Simek [Tue, 30 Aug 2016 14:17:27 +0000 (16:17 +0200)]
ARM64: zynqmp: Force certain bootmode for SPL
ZynqMP provides an option to overwrite bootmode setting which
can change SPL behavior.
For example: boot SPL via JTAG and then SPL loads images from SD.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Chris Packham [Wed, 9 Nov 2016 09:21:45 +0000 (22:21 +1300)]
tools/kwbimage: add DEBUG option
Offset 0x1 in the generated kwb image file is a set of flags, bit 0
enables debug output from the BootROM firmware. Allow a DEBUG option in
the kwb configuration to request debug output from the BootROM firmware.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Wed, 9 Nov 2016 09:07:45 +0000 (22:07 +1300)]
tools/kwbimage: add BAUDRATE option
Offset 0x18 in some Marvell datasheets this field is redacted as
"reserved". This offset is actually a set of options and bits 2:0 allow
the selection of the UART baudrate.
Allow a BAUDRATE option to set the UART baudrate for any messages coming
from the BootROM firmware.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Marek Vasut [Thu, 1 Dec 2016 01:06:33 +0000 (02:06 +0100)]
mmc: Tinification of the mmc code
Add new configuration option CONFIG_MMC_TINY which strips away all
memory allocation within the MMC code and code for handling multiple
cards. This allows extremely space-constrained SPL code use the MMC
framework.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Jaehoon Chung <jh80.chung@samsung.com>
Marek Vasut [Thu, 1 Dec 2016 01:06:32 +0000 (02:06 +0100)]
mmc: Fix warning if debug() is not used
If debug() is not used, then the whole content of debug(...) will
be removed by the preprocessor, which will result in the following
warning. This patch adds __maybe_unused annotation to fix this.
drivers/mmc/mmc.c: In function ‘mmc_init’:
drivers/mmc/mmc.c:1685:11: warning: variable ‘start’ set but not used [-Wunused-but-set-variable]
unsigned start;
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Jaehoon Chung <jh80.chung@samsung.com>
Tom Rini [Wed, 30 Nov 2016 19:14:47 +0000 (14:14 -0500)]
ts4600: Disable CONFIG_DISPLAY_CPUINFO
Without this change we see:
../arch/arm/cpu/arm926ejs/mxs/mxs.c: In function ‘print_cpuinfo’:
../arch/arm/cpu/arm926ejs/mxs/mxs.c:181:23: warning: unused variable ‘data’ [-Wunused-variable]
../arch/arm/cpu/arm926ejs/mxs/mxs.c:180:6: warning: variable ‘cpurev’ set but not used [-Wunused-but-set-variable]
So the easy solution is to disable CONFIG_DISPLAY_CPUINFO
Reviewed-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 30 Nov 2016 19:05:08 +0000 (14:05 -0500)]
travis.yml: Split Freescale ARM job up more
In order to avoid running into the time limit, split the 32bit and 64bit
Freescale boards into separate jobs. We could either pass
"freescale & armv8" to buildman or exclude all of the 32bit CPUs. While
the former is shorter I fear the amount of possible escaping required
would make things less readable.
Paul Burton [Mon, 26 Sep 2016 18:28:57 +0000 (19:28 +0100)]
MIPS: Fix map_physmem for cached mappings
map_physmem should return a pointer that can be used by the CPU to
access the given memory - on MIPS simply returning the physical address
as it does prior to this patch doesn't achieve that. Instead return a
pointer to the memory within (c)kseg0, which matches up consistently
with the (c)kseg1 pointer that uncached mappings return via ioremap.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Mon, 26 Sep 2016 18:28:56 +0000 (19:28 +0100)]
MIPS: Use ram_top, not bi_memsize, in arch_lmb_reserve
When calculating the region to reserve for the stack in
arch_lmb_reserve, make use of ram_top instead of adding bi_memsize to
CONFIG_SYS_SDRAM_BASE. This avoids overflow if the system has enough
memory to reach the end of the address space.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
MIPS: add handling for generic and EJTAG exceptions
Add exception handlers for generic and EJTAG exceptions. Most of
the assembly code is imported from Linux kernel and adapted to U-Boot.
The exception vector table will be reserved above the stack before
U-Boot is relocated. The exception handlers will be installed and
activated after relocation in the initr_traps hook function.
Generic exceptions are handled by showing a CPU register dump similar
to Linux kernel. For example:
EJTAG exceptions are checked for SDBBP and delegated to the SDBBP handler
if necessary. Otherwise the debug mode will simply be exited. The SDBBP
handler currently prints the contents of registers c0_depc and c0_debug.
This could be extended in the future to handle semi-hosting according to
the MIPS UHI specification.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Tested-by: Paul Burton <paul.burton@imgtec.com>
In order to set own exception handlers, a table with the exception
vectors must be built in DRAM and the CPU EBase register must be
set to the base address of this table.
Reserve the space above the stack and use gd->irq_sp as storage
for the exception base address.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
MIPS: add possibility to setup initial stack and global data in SRAM
This adds a new Kconfig option CONFIG_MIPS_INIT_STACK_IN_SRAM which
a SoC can select if it supports some kind of SRAM. Together with
CONFIG_SYS_INIT_SP_ADDR the initial stack and global data can be
set up in that SRAM. This can be used to provide a C environment
also for lowlevel_init().
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Clear cp0 status while preserving implementation specific bits.
Set bits BEV and ERL as the arch specification requires after
a reset or soft-reset exception.
Extend and fix initialization of watch registers. Check if additional
watch register sets are implemented and initialize them too.
Initialize cp0 count as early as possible to get the most
accurate boot timing.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
When booting from ROM, early exceptions can't be handled
properly. Instead of busy-looping give the developer the
possibilty to examine the situation. Invoke an UHI
exception operation which can be read as unhandled exception
by a hardware debugger if one is attached. If the debugger
doesn't support UHI, the exception is read as unexpected
breakpoint.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
MIPS: make inclusion of ROM exception vectors configurable
This adds a compile time option to include code for static
exception vectors. Static exception vectors are only needed,
when the U-Boot entry point is equal to the CPU reset exception
vector address. For instance this is the case when U-Boot is
used as ROM in Qemu or booted from parallel NOR flash. When
U-Boot is booted from RAM (e.g. loaded there by SPL), the
exception vectors need to be setup dynamically, which is done
in follow-up commits.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch extends the imx6 clock code to enable or disable the EIM
slow clock, which in necessary when one wants to use EIM interface t
o read/write from external memory (e.g. NOR).
Tom Rini [Tue, 29 Nov 2016 17:41:19 +0000 (12:41 -0500)]
travis.yml: Add samsung and rockchip builds
The catch-all job is failing due to time limits depending on factors out
of our control, so move Samsung and Rockchip boards into their own jobs
and then exclude them from the general ARM and AArch64 jobs.
Angus Ainslie [Fri, 11 Nov 2016 18:31:39 +0000 (11:31 -0700)]
imx7: SPI: add suport for SPI flash in mikroBUS slot
Enable the escpi3 nets attached to the mikroBUS slot
on the i.MX7 Sabre evalution board. Also enble the SPI flash
commands to work with the "flash click" board.
This is V2 of this patch with changes recommended by the maintainer
Stefan Agner [Tue, 15 Nov 2016 18:38:23 +0000 (10:38 -0800)]
arm: mx6: specify SPL padding
Specify standard padding for payload to 68KB. This is derived from
the maximum header size plus maximum SPL size. It matches the
already defined offset for SD/eMMC devices (69KB) too. This allows
to use the u-boot-with-spl.imx build target to generate a directly
flashable image which can be flashed using:
While the patch has been created with SD/eMMC in mind, this also
works with other boot media. The board file needs to configure the
media specific (absolute) payload offset accordingly. Especially
the IVT offset is boot media specific and can be retrieved from the
reference manual (Table 8-25. Image Vector Table Offset and Initial
Load Region Size). For NAND boot a define like this should do the
job:
Breno Lima [Fri, 25 Nov 2016 18:56:57 +0000 (16:56 -0200)]
mx6sx: Add initial support for UDOO Neo Board
UDOO Neo Board is a development board from Seco that has three models:
- UDOO Neo Basic
- UDOO Neo Basic Kick Starter
- UDOO Neo Extended
- UDOO Neo Full
All versions are based on the i.MX6 SoloX processor.
For more details about the UDOO Neo board, please refer to:
http://www.udoo.org/udoo-neo/
This work is based on a previous commit of Francesco Montefoschi
<francesco.monte@gmail.com>:
https://github.com/fmntf/u-boot/commit/877b71184a5105e708024f232d36aed574961844
Only tested on the UDOO Neo Full board.
Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Sanchayan Maity [Fri, 25 Nov 2016 10:49:17 +0000 (16:19 +0530)]
colibri_vf: Read kernel and device tree from static UBI volumes
Our update scripts write the kernel and device tree in seperate
UBI volumes. This allows to use a lot less UBI/UBIFS support in
U-Boot, which should lower the risk of hitting bugs in this area.
Eric Nelson [Sun, 30 Oct 2016 23:33:50 +0000 (16:33 -0700)]
ARM: mx6: ddr: use Kconfig for inclusion of DDR calibration routines
The DDR calibration routines are gated by conditionals for the
i.MX6DQ SOCs, but with the use of the sysinfo parameter, these
are usable on at least i.MX6SDL and i.MX6SL variants with DDR3.
Also, since only the Novena board currently uses the dynamic
DDR calibration routines, these routines waste space on other
boards using SPL.
Add a KConfig entry to allow boards to selectively include the
DDR calibration routines.
Eric Nelson [Sun, 30 Oct 2016 23:33:49 +0000 (16:33 -0700)]
mx6: ddr: add routine to return DDR calibration data
Add routine mmdc_read_calibration() to return the output of DDR
calibration. This can be used for debugging or to aid in construction
of static memory configuration.
This routine will be used in a subsequent patch set adding a virtual
"mx6memcal" board, but could also be useful when gathering statistics
during an initial production run.
Eric Nelson [Sun, 30 Oct 2016 23:33:48 +0000 (16:33 -0700)]
mx6: ddr: pass mx6_ddr_sysinfo to calibration routines
The DDR calibration routines have scattered support for bus
widths other than 64-bits:
-- The mmdc_do_write_level_calibration() routine assumes the
presence of PHY1, and
-- The mmdc_do_dqs_calibration() routine tries to determine
whether one or two DDR PHYs are active by reading MDCTL.
Since a caller of these routines must have a valid struct mx6_ddr_sysinfo
for use in calling mx6_dram_cfg(), and the bus width is available in the
"dsize" field, use this structure to inform the calibration routines which
PHYs are active.
This allows the use of the DDR calibration routines on CPU variants
like i.MX6SL that only have a single MMDC port.
Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Marek Vasut <marex@denx.de>
Eric Nelson [Fri, 28 Oct 2016 17:13:57 +0000 (10:13 -0700)]
imx: mx6: ddr: add register MPZQLP2CTL for LPDDR2
Add constants for the MPZQLP2CTL DDR register for both
banks to allow setting the LPDDR2 timing values in
.cfg files using a named constant instead of hex addresses
as is currently done in mx6slevk and other board files.
Sven Ebenfeld [Fri, 25 Nov 2016 20:42:53 +0000 (21:42 +0100)]
arm: imx: wandboard: fix compile error if CONFIG_VIDEO is deactivated
When I tried to deactivate VIDEO support for the Wandboard, it still
tried to initialize the Framebuffer and so on. That is the reason for
the added ifdefs. CONFIG_VIDEO is enabled in the configuration as default
and therefore nothing changes for the default user.
The structs mx6dl_i2c2_pad_info and mx6q_i2c2_pad_info are only available
when CONFIG_IPUV3 are set and should not be tried to access, when that
define is not defined.
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Soeren Moch [Sun, 27 Nov 2016 15:02:19 +0000 (16:02 +0100)]
tbs2910: Make Ethernet functional again
Configure the PHY to output a 125MHz clk from CLK_25M and set tx clock delay.
This patch is similar to commit 4b6035da482cccda06aeb419634f99937c9fc783
("mx6sabresd: Make Ethernet functional again").
The ipu has two display interfaces. Make the used one a parameter
in struct display_info_t instead of using unconditionally DI0.
DI0 is the default setting.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Eric Nelson <eric@nelint.com>
If CONFIG_SPL_LIBCOMMON_SUPPORT is not defined there is a lone case statement
at the end of the switch leading to a compile error.
Remove the offending case statement.
| common/spl/spl_mmc.c:339:7: error: label at end of compound statement
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Marek Vasut <marex@denx.de>
Marcin Niestroj [Fri, 21 Oct 2016 11:53:54 +0000 (13:53 +0200)]
ARM: mx6: add MMC2 boot device detection support in SPL
Check BOOT_CFG2[3:4] to determine which SD/MMC port is selected to boot
from. If MMC2 is selected return BOOT_DEVICE_MMC2. In all other cases
return BOOT_DEVICE_MMC1, as we do not have corresponding macro for MMC3
and MMC4.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Peng Fan [Tue, 22 Nov 2016 11:41:09 +0000 (19:41 +0800)]
armv7: psci: cpu_off: flush D-Cache before disable D-Cache
Before disable cache, need to first flush cache.
There maybe dirty data in D-Cache before disable D-Cache.
After disable D-Cache, the first store instructions in
psci_v7_flush_dcache_all will directly store registers
{r4-r5, r7, r9-r11, lr} to memory.
If there is dirty data before disable D-Cache,
psci_v7_flush_dcache_all will flush data to memory,
and may overwrite the memory that hold the registers
{r4-r5, r7, r9-r11, lr}.
So before disable cache, first flush D-Cache.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Hongbo Zhang <hongbo.zhang@nxp.com> Cc: York Sun <york.sun@nxp.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Tom Rini <trini@konsulko.com>
Liviu Dudau [Tue, 22 Nov 2016 11:19:18 +0000 (11:19 +0000)]
vexpress64: Juno: Change PCI buss addresses for IO to start from zero.
Juno uses a 1:1 mapping between CPU and PCI addresses for IO. First,
that will trip devices that cannot use more than 16 bits of addresses
for IO, second it is un-necessary as the system can handle zero-based
PCI addresses just fine.
Change the mapping to start IO bus addresses from zero.
Mugunthan V N [Thu, 11 Aug 2016 14:34:03 +0000 (20:04 +0530)]
drivers: net: keystone_net: add rgmii link type support when parsing dt
Add support to detect RGMII link interface from link-interface
device tree entry. Also rename the existing link type enums so
that it provides meaningful interface like SGMII.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reported-by: Sekhar Nori <nsekhar@ti.com> Tested-by: Sekhar Nori <nsekhar@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When using OF_CONTROL, the disabled value of the mini UART platdata
gets reset after board_early_init_f. So move detection and disabling
to board_init and remove board_early_init_f.
This uses the first device using the mini uart driver, as this method
works reliably with different device trees or even no device tree at all.
Signed-off-by: Fabian Vogt <fvogt@suse.com> Reviewed-by: Simon Glass <sjg@chromium.org>
serial: bcm283x_mu: support disabling after initialization
For the Raspberry Pi 3 it needs to be possible to disable the serial
device after initialization happens, as only after the GPIO device is available
it is known whether the mini uart is usable.
Signed-off-by: Fabian Vogt <fvogt@suse.com> Reviewed-by: Simon Glass <sjg@chromium.org>
The information currently set via platdata has to be represented in the
device tree now. bcm283x-uboot.dtsi adds the u-boot specific "skip-init"
property to the serial nodes and enables initialization in the pre-reloc phase.
Cc: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Fabian Vogt <fvogt@suse.com> Reviewed-by: Simon Glass <sjg@chromium.org>
serial: pl01x: expose skip_init platdata option in DT
To be able to represent the skip-init platdata element with OF_CONTROL,
it needs to be read from the device tree as well and put into the platform data.
Cc: Eric Anholt <eric@anholt.net> Signed-off-by: Fabian Vogt <fvogt@suse.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log