Mark Tomlinson [Tue, 28 Aug 2018 22:51:14 +0000 (10:51 +1200)]
tools: mkimage: Ensure munmap unmaps the same length that was mapped
The set_header call in kwbimage.c adds a checksum to the end of the
image in addition to setting up the header. It 'helpfully' updates the
st_size to match the fact that the file is now longer. However, mkimage
uses this length in the munmap call. This can lead to unmapping an extra
page, of perhaps required data. When this happens, a SEGV can occur.
To prevent this from happening, the munmap call now uses the same length
that was passed to mmap. This could also have been fixed by not changing
the length in kwbimage.c, however changing it in the main file means
that other plugins will also not fall for the same trap.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by: Chris Packham <judge.packham@gmail.com>
[cp: resolve checkpatch complaints] Tested-by: Chris Packham <judge.packham@gmail.com>
Add support for loading U-Boot on the Broadcom 7260 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Change the configured serial console index to reflect that it is the
first physical UART, reorder some defconfig lines and move some
environment configuration from bcmstb.h to bcm7445.h.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org> Cc: Florian Fainelli <f.fainelli@gmail.com>
Adam Ford [Thu, 16 Aug 2018 18:23:11 +0000 (13:23 -0500)]
ARM: CPU: arm926ejs: Consolidate cache routines to common file
Four different boards had different options for enabling cache
that were virtually all the same. This consolidates these
common functions into arch/arm/cpu/arm926ejs/cache.c
This also has the positive side-effect of enabling cache on
the Davinci (da850) boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add mach-at91 to the list of consolidations] Signed-off-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Thu, 16 Aug 2018 13:11:49 +0000 (18:41 +0530)]
pinctrl: Fix build warning with ARM64
Following build warning appears when pinctrl-single is built for ARM64:
In file included from drivers/pinctrl/pinctrl-single.c:10:0:
drivers/pinctrl/pinctrl-single.c: In function ‘single_configure_pins’:
./arch/arm/include/asm/io.h:43:28: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
#define __arch_getw(a) (*(volatile unsigned short *)(a))
Fix this by using phys_addr_t for variable reg instead of u32
Lokesh Vutla [Thu, 16 Aug 2018 12:56:55 +0000 (18:26 +0530)]
dm: omap-timer: Update clock rate only if not populated
timer_pre_probe() tries to populate the clock rate from DT. omap
timer driver tries to overwrite this value irrespective of the value
populated fro DT. So update this value only when DT doesn't populate
the clock rate.
Peng Fan [Fri, 10 Aug 2018 06:07:55 +0000 (14:07 +0800)]
mmc: fsl_esdhc: enable HS400 feature
The strobe dll code is ported from Linux Kernel:
drivers/mmc/host/sdhci-esdhc-imx.c
The comments are from the above file,
"For HS400 eMMC, there is a data_strobe line. This signal is generated
by the device and used for data output and CRC status response output
in HS400 mode. The frequency of this signal follows the frequency of
CLK generated by host. The host receives the data which is aligned to the
edge of data_strobe line. Due to the time delay between CLK line and
data_strobe line, if the delay time is larger than one clock cycle,
then CLK and data_strobe line will be misaligned, read error shows up.
So when the CLK is higher than 100MHz, each clock cycle is short enough,
host should configure the delay target. "
Peng Fan [Fri, 10 Aug 2018 06:07:54 +0000 (14:07 +0800)]
mmc: add HS400 support
Add HS400 support.
Selecting HS400 needs first select HS200 according to spec, so use
a dedicated function for HS400.
Add HS400 related macros.
Remove the restriction of only using the low 6 bits of
EXT_CSD_CARD_TYPE, using all the 8 bits.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Jean-Jacques Hiblot <jjhiblot@ti.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Marek Vasut <marex@denx.de> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Eugen Hristev [Thu, 9 Aug 2018 11:12:01 +0000 (14:12 +0300)]
at91: fix devicetree warnings
This commit fixes various devicetree warnings in the at91 devicetrees
like:
arch/arm/dts/sama5d36ek_cmp.dtb: Warning (avoid_unnecessary_addr_size): /gpio_keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
These warnings make buildman report failed builds for most of at91 boards.
Thus, fixing it.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Patrice Chotard [Thu, 9 Aug 2018 09:57:57 +0000 (11:57 +0200)]
gpio: stm32f7: replace ODR update by BSRR write
Replace clrsetbits on ODR register (2 operations: one read + one write)
by writing on the correct bit (SET or RESET) of the BSRR register
(only 1 write operation).
Moreover this register if safe for simultaneous access by 2 master on
the bus.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Neil Armstrong [Mon, 6 Aug 2018 12:49:20 +0000 (14:49 +0200)]
clk: clk_meson: Add mux and div support for reparent and rate setting
This patch adds support for :
- Rate calculation through muxes and generic dividers
- Basic gate setting propagation
- Reparenting for muxes
- Clock rate setting through generic dividers without reparenting
Support is only added to the Composite VPU and VAPB clocks in order
to support the Video Processing Unit Power Domain clock setup.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Mon, 6 Aug 2018 12:49:19 +0000 (14:49 +0200)]
power: domain: Add the VPU Power Domain driver
The Amlogic Meson SoCs embeds a specific Power Domain dedicated to the
Video Processing Unit.
This patch implements support for this power domain in preparation of the
future support for the Video display support in U-Boot.
This driver will depend on changes in the clock driver to handle the setup
of the VPU and VAPB clocks configured from DT using assigned-clocks entries.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Masahiro Yamada [Mon, 6 Aug 2018 11:47:39 +0000 (20:47 +0900)]
arch: types.h: factor out fixed width typedefs to int-ll64.h
All architectures have the same definition for s8/16/32/64
and u8/16/32/64.
Factor out the duplicated code into <asm-generic/int-ll64.h>.
BTW, Linux unified the kernel space definition into int-ll64.h
a few years ago as you see in Linux commit 0c79a8e29b5f
("asm/types.h: Remove include/asm-generic/int-l64.h").
Masahiro Yamada [Mon, 6 Aug 2018 11:47:38 +0000 (20:47 +0900)]
Remove CONFIG_USE_STDINT
You do not need to use the typedefs provided by compiler.
Our compilers are either IPL32 or LP64. Hence, U-Boot can/should
always use int-ll64.h typedefs like Linux kernel, whatever the
typedefs the compiler internally uses.
Adam Ford [Sat, 4 Aug 2018 21:34:54 +0000 (16:34 -0500)]
arm: armv7-a: Compile and tune for armv7-a instead of armv5
arch/arm/Makefile references armv5 for backwards compatibility with
older compilers. This patch removes those references to armv5,
since by now newer compilers are required which should have armv7
support enabled.
The Makefile also also has a list of options for mtune, but the
entry for CONFIG_CPU_V7A is empty, so this patch tunes the
CPU_V7A architecture to generic-armv7-a.
The following size changed apply to omap3_logic using GCC.
Stock
text data bss dec hex filename
50910 429 67580 118919 1d087 spl/u-boot-spl
540713 22700 327072 890485 d9675 u-boot
Without Armv5
text data bss dec hex filename
50916 429 67580 118925 1d08d spl/u-boot-spl
540719 22700 327064 890483 d9673 u-boot
mtune=generic-armv7-a
text data bss dec hex filename
50932 429 67580 118941 1d09d spl/u-boot-spl
540519 22700 327080 890299 d95bb u-boot
Patrice Chotard [Fri, 3 Aug 2018 13:07:39 +0000 (15:07 +0200)]
serial: stm32: Replace setparity by setconfig
Replace stm32_serial_setparity by stm32_serial_setconfig
which allows to set serial bits number, parity and stop
bits number.
Only parity setting is implemented.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
console: unify fgetc function when console MUX is deactivated
Unify the fgetc function when MUX is activated or not:
- always call tstc() : it is the normal behavior expected
by serial uclass (call tstc then getc) and that avoids
issue when SERIAL_RX_BUFFER is activated
- reload WATCHDOG in the char waiting loop
This patch allow to have the same behavior when CONSOLE_MUX is activated
or not and avoid regression when this feature is deactivated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Matt Weber [Fri, 27 Jul 2018 03:37:53 +0000 (22:37 -0500)]
include/version.h: workaround sysroot inc order
On some systems the host system or even the cross sysroot can
contain a version.h. This leads to the wrong file being picked
up and a PLAIN_VERSION undefined error.
This workaround symlinks the version.h into the tool folder to
allow reordering of search folders.
Fixes
http://autobuild.buildroot.net/results/770/7702d5df36a6532aafdbe6e9e62709bbfa058b54/build-end.log
http://autobuild.buildroot.net/results/e34/e3401027d2fb3ce565ca9e2456a427afd3610a87/build-end.log
... additional can be found with these queries ...
http://autobuild.buildroot.net/?reason=uboot-tools-2018.03
http://autobuild.buildroot.net/?reason=uboot-tools-2018.05
Upstream: pending
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
mtd: nand: denali: fix unaligned cache operations on ARMv7 SoCs
If the OOB size is not multiple of the cache line size, the ARMv7
cache operation still prints "Misaligned operation at range".
=> nand info
Device 0: nand0, sector size 256 KiB
Page size 4096 b
OOB size 224 b
Erase size 262144 b
subpagesize 4096 b
options 0x00104200
bbt options 0x00060000
=> nand dump 0
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
...
The cache flushing operations won't happen in this case to cover all of
the range to fix this by making sure we have things aligned.
Reported-by: Marek Vasut <marex@denx.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Reword the commit message to be clear this is a direct problem
rather than just a warning]
Marek Vasut [Sun, 9 Sep 2018 14:30:11 +0000 (16:30 +0200)]
fdt: fix get_next_memory_node()
The get_next_memory_node() always sets mem to -1 , which is incorrect,
because then every iteration of memory bank parsing will start from the
first memory bank instead of the previous one.
On systems with 1 memory bank defined in DT and CONFIG_NR_DRAM_BANKS=4 ,
like ie. r8a77965-salvator-x , this will result in U-Boot incorrectly
reporting four identical memory banks with the same memory configuration.
Fix this by setting mem to startoffset value, which restores the behavior
before the fixed patch was applied.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Jens Wiklander <jens.wiklander@linaro.org> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Fixes: 452bc121027d ("fdt: fix fdtdec_setup_memory_banksize()") Tested-by: Michal Simek <michal.simek@xilinx.com> [on ZynqMP}
ARM: Specify aligned address for secure section instead of using attributes
In commit a1274cc94a20 ("ARM: Page align secure section only when it is
executed in situ"), we used output section attributes (the "ALIGN"
keyword after the colon) to specify the alignment requirements. Using
the constant "COMMONPAGE" there was recently broken in binutils 2.31 [1].
Binutils maintainer Alan Modra suggested the former method would still
work. Since both methods achieve the same result, this patch does just
that. This fixes the "reboot after bootm" issue we've been seeing on
sunxi when booting non-secure.
ARM: qemu-arm: Fix qemu_arm64_defconfig for QEMU 3.0
QEMU 3.0 introduced additional memory-mapped regions for PCI-E ECAM and
MMIO. Thus we need to add them to our MMU map or U-Boot will crash with
a Synchronous Abort during PCI-E probing when it tries to access the
unmapped ECAM memory area.
Reported-by: Jonathan Gray <jsg@jsg.id.au> Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi> Tested-by: Jonathan Gray <jsg@jsg.id.au>
When re-syncing the DTS files from the kernel, something caused
the MMC driver to no longer detect the MMC card. Undoing the
CD-invert appears to fix the issue.
Fixes: e6ea2390cde3 ("ARM: DTS: Resync LogicPD-Torpedo-37xx-devkit
with Linux 4.18-RC4")
Stefan Agner [Mon, 6 Aug 2018 07:19:19 +0000 (09:19 +0200)]
colibri_imx7_emmc: add Colibri iMX7D 1GB (eMMC) module support
This commit adds support for the Toradex Colibri iMX7D 1GB Computer
on Module. The module is very similar to the Colibri iMX7D 512MB
but uses eMMC instead of raw NAND. This patch introduces a new
board specific Kconfig symbol to select between the two flash
options.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The resume entry function has to initialize stack pointer before calling
C code, otherwise there will be an external abort occur, in additional,
invalidate L1 cache must be done in secure section as well, so this
patch also adds assembly code back and keep it as simple as possible.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Acked-by: Stefan Agner <stefan@agner.ch> Tested-by: Stefan Agner <stefan@agner.ch>
Anson Huang [Wed, 8 Aug 2018 01:17:48 +0000 (09:17 +0800)]
imx: mx7: psci: improve cpu hotplug flow
This patch improves cpu hotplug, previous cpu_off
implementation is NOT safe, a CPU can NOT power down
itself in runtime, it will cause system bus hang due
to pending transaction. So need to use other online
CPU to kill it when it is ready for killed.
Here use SRC parameter register and a magic number
of ~0 as handshake for killing a offline CPU,
when the online CPU checks the psci_affinity_info,
it will help kill the offline CPU according to
the magic number stored in SRC parameter register.
Alex Kiernan [Tue, 24 Jul 2018 07:29:40 +0000 (07:29 +0000)]
Cleanup CONFIG_BOOTDELAY on cl-som-imx7
CONFIG_BOOTDELAY has been migrated to Kconfig, but cl-som-imx7 was
missed. We can just delete the assignments as the config already has
the correct value.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Martin Kaiser [Sat, 21 Jul 2018 17:47:03 +0000 (19:47 +0200)]
watchdog: mx25: use the imx_watchdog driver for mx25
The existing imx_watchdog driver is compatible with mx25 chipsets.
Add a WDOG1_BASE_ADDR define for the base address and enable the driver
in watchdog's Makefile.
To use the driver, a board must define CONFIG_IMX_WATCHDOG and
CONFIG_HW_WATCHDOG.
This fixes an issue when booting an mx25 chip via usb/serial. In this
case, the boot rom will always enable the watchdog. If u-boot is running
in interactive mode and the watchdog is not serviced, the system is
rebooted when the watchdog expires.
Signed-off-by: Martin Kaiser <martin@kaiser.cx> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Ye Li [Thu, 28 Jun 2018 02:30:53 +0000 (19:30 -0700)]
imx: imx7d-sdb: Add DM QSPI support
On iMX7D SabreSD board, the QSPI has pins conflict with EPDC (default).
To use QSPI, users have to rework the board (de-populate R388-R391, R396-R399
populate R392-R395, R299, R300). So we add new DTS file and new defconfig
dedicated for QSPI.
Other changes to support the DM QSPI:
- Add QSPI node and alias spi0.
- Modify spi4 (spi-gpio) node and add alias spi5 for it to avoid req
conflict
- Add EPDC node in imx7d.dtsi and disable it in imx7d-sdb-qspi.dts to
align with kernel and also present the conflict.
- Add -u-boot.dtsi to modify compatible string of mx25l51245g@0 to
"spi-flash"
- Remove iomux settings of qspi in board codes which is not needed
for DM driver.
Ye Li [Thu, 28 Jun 2018 02:27:00 +0000 (19:27 -0700)]
imx: imx6sx-sabreauto: convert to use DM QSPI driver
To support DM QSPI driver:
- Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
to "spi-flash" and add "num-cs" property.
- Enable DM SPI and DM SPI FLASH configurations
- Remove iomux settings of qspi1 in board codes which is not needed
for DM driver.
Ye Li [Thu, 28 Jun 2018 02:26:59 +0000 (19:26 -0700)]
imx: imx6sx-sdb: Enable DM QSPI driver
To support DM QSPI driver
- Add spi0 and spi1 alias for qspi1 and qspi2.
- Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
to "spi-flash" and add "num-cs" property.
- Enable DM SPI/QSPI relavent configurations
- Remove iomux settings of qspi2 in board codes which is not needed
for DM driver.
- Add sf default settings. So running "sf probe" can detect the flash
Masahiro Yamada [Fri, 24 Aug 2018 10:30:15 +0000 (19:30 +0900)]
Make kmalloc'ed memory really DMA-safe
In Linux, the memory returned by kmalloc() is DMA-capable.
However, it is not true in U-Boot.
At a glance, kmalloc() in U-Boot returns address aligned with
ARCH_DMA_MINALIGN. However, it never pads the allocated memory.
This half-way house is completely useless because calling kmalloc()
and malloc() in this order causes a cache sharing problem.
Change the implementation to call malloc_cache_aligned(), which
allocates really DMA-capable memory.
hisilicon: hikey: Update instructions based on latest source
Update the HiKey board instructions based on the latest source
available. These instructions are derived from the ATF platform doc.
While updating the instructions, some comments on ATF issue has been
removed since it is fixed in latest ATF source.
Bin Meng [Fri, 24 Aug 2018 04:28:58 +0000 (21:28 -0700)]
x86: zimage: Remove acpi_rsdp_addr propagation to kernel boot parameters
As of today, the proposal of adding "acpi_rsdp_addr" to the kernel
boot protocol does not make its way to the kernel mainline. This
creates some confusion if we leave it in the U-Boot code base.
Remove it for now until we have a clear picture with kernel upstream.
Note this eventually does a partial revert to commit 3469bf427454
("x86: zImage: Propagate acpi_rsdp_addr to kernel via boot parameters")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 23 Aug 2018 15:24:10 +0000 (08:24 -0700)]
x86: zimage: Support booting Linux kernel from an EFI payload
At present Linux kernel loaded from U-Boot as an EFI payload does
not boot. This fills in kernel's boot params structure with the
required critical EFI information like system table address and
memory map stuff so that kernel can obtain essential data like
runtime services and ACPI table to boot.
With this patch, now U-Boot as an EFI payload becomes much more
practical: it is another option of kernel bootloader, ie, can be
a replacement for grub.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Ley Foon Tan [Tue, 28 Aug 2018 16:08:48 +0000 (00:08 +0800)]
usb: dwc2: Add reset ctrl to driver
Add code to reset all reset signals as in usb DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Marek Vasut [Fri, 24 Aug 2018 19:03:14 +0000 (21:03 +0200)]
pci: rmobile: Filter out device 1 and 2
Only PCI device 1 and 2 is populated on the R-Car Gen2 internal
PCIe controller. Ignore all other devices. This fix prevents a
duplication of OHCI controller response on slot 0 and 1.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Tue, 7 Aug 2018 10:27:10 +0000 (12:27 +0200)]
usb: ehci: Add PHY support to ehci-pci
Add support for operating a PHY attached to ehci-pci. There are
systems where the EHCI controller is internally wired to a PCI
bus and has a PHY connected to it as well, ie. the R-Car Gen2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Thu, 16 Aug 2018 12:37:03 +0000 (14:37 +0200)]
phy: Fix warning due to missing definition of structure
Fix this sort of warning if generic-phy.h is included:
include/generic-phy.h:52:42: warning: ‘struct ofnode_phandle_args’ declared inside parameter list will not be visible outside of this definition or declaration
int (*of_xlate)(struct phy *phy, struct ofnode_phandle_args *args);
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Copy missing Kernel patch to make SLEWCTRL_SLOW available in device tree
and to correct the value of SLEWCTRL_FAST.
After this patch, the Kernel and U-boot device tree settings for
SLEWCTRL have the same effect.
"
According to AM335x TRM, Document spruh73l, Revised February 2015,
Section 9.2.2 Pad Control Registers, setting bit 6 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness. Current users of the macro (i2c and mdio) are left
unmodified as SLEWCTRL_FAST was the macro used and actual desired state.
Tested on am335x-gp-evm with no difference in software performance seen. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
"
Signed-off-by: Christian Amann <Christian.Amann@de.bosch.com>
Marek Vasut [Tue, 21 Aug 2018 13:53:33 +0000 (15:53 +0200)]
env: ubi: Add missing ENV_NAME
Add missing environment name for UBI, to prevent this NULL in output:
Loading Environment from <NULL>...
and rather have a valid UBI there:
Loading Environment from UBI...
Neil Stainton [Mon, 20 Aug 2018 15:46:19 +0000 (15:46 +0000)]
u-boot: align cache flushes in load_elf_image_shdr to line boundaries
Prevent cache warning messages when using the 'bootelf' command on an
Arm target. Round down each section start address and round up the
respective section end to the nearest cache line.
Currently when using bootelf to load an image on Arm, several warnings
such as the following appear in the console:
CACHE: Misaligned operation at range [87800000, 8783c5e0]
CACHE: Misaligned operation at range [8783c5e0, 8784b3e0]
Signed-off-by: Neil Stainton <nstainton@asl-control.co.uk>
[trini: Reword commit message to include the info after the --- which
included the Signed-off-by line, and change ' at ' to '@'] Signed-off-by: Tom Rini <trini@konsulko.com>
In an earlier proposed patch, bcmstb.c implemented timer_read_counter,
but it was updated to implement get_ticks instead. This patch updates
the declaration in timer.h accordingly.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
[common/avb_verify.c:738] -> [common/avb_verify.c:741]: (warning) \
Either the condition 'ops' is redundant or there is possible null \
pointer dereference: ops.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>