Stefan Roese [Fri, 3 May 2019 06:42:17 +0000 (08:42 +0200)]
arm: mvebu: clearfog: Enable BLK and DM support
This patch enables CONFIG_BLK and some DM enabled drivers on clearfog
to remove these compile warnings:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does use CONFIG_LIBATA but has CONFIG_AHCI not
enabled. Please update the storage controller driver to use
CONFIG_AHCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Chen-Yu Tsai [Fri, 3 May 2019 02:27:41 +0000 (10:27 +0800)]
sunxi: Enable EMAC on the Bananapi M3
The Bananapi M3 has an RTL8211E PHY connected to the EMAC using
RGMII. The PHY is powered by DCDC1 through SW @ 3.3V.
The board is designed to use 3.3V with RGMII, instead of the standard
reduced voltage of 2.5V we see everywhere. DLDO3, which provides the
I/O voltages, is raised to match.
This patch enables the EMAC and Realtek PHY drivers in the defconfig.
The device tree file already has the EMAC enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Chen-Yu Tsai [Fri, 3 May 2019 02:27:40 +0000 (10:27 +0800)]
sunxi: Enable EMAC on the Cubietruck Plus
The Cubietruck Plus has an RTL8211E PHY connected to the EMAC using
RGMII. The PHY is powered by DLDO4 @ 3.3V, while the I/O pins are
powered by DLDO3 @ 2.5V.
This patch enables the EMAC and Realtek PHY drivers in the defconfig.
The device tree file already has the EMAC enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Known broken:
- Internal keyboard (seems to be because the keyboard firmware loads a
bootloader first, and then disconnects bootloader and connect real
keyboard). External ones connected to the USB port work fine.
This patch enables support for the A64-Teres-I board to u-boot,
including enabling screen backlight (lacking from Linux device-tree).
Linux commit details about the sun50i-a64-teres-i.dts sync:
"arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins"
(sha1: d91ebb95b96c8840932dc3a10c9f243712555467)
Cosmetic warnings regarding whitespace and placement of SPDX notice for
dts file was ignored.
config and .dtsi file are adapted from pinebook files.
Tested-by: Jonas Smedegaard <dr@jones.dk> Signed-off-by: Jonas Smedegaard <dr@jones.dk> Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: move board entry in MAINTAINERS file at proper position] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 27 Feb 2019 18:56:55 +0000 (00:26 +0530)]
reset: Get the RESET by index without device
Getting a RESET by index with device is not straight forward
for some use-cases like handling clock operations for child
node in parent driver. So we need to process the child node
in parent probe via ofnode and process RESET operation for child
without udevice but with ofnode.
So add reset_get_by_index_nodev() and move the common code
in reset_get_by_index_tail() to use for reset_get_by_index()
Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Jagan Teki [Wed, 27 Feb 2019 18:56:52 +0000 (00:26 +0530)]
clk: Get the CLK by index without device
Getting a CLK by index with device is not straight forward
for some use-cases like handling clock operations for child
node in parent driver. So we need to process the child node
in parent probe via ofnode and process CLK operation for child
without udevice but with ofnode.
So add clk_get_by_index_nodev() and move the common code
in clk_get_by_index_tail() to use for clk_get_by_index()
Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Jagan Teki [Wed, 8 May 2019 14:26:16 +0000 (19:56 +0530)]
serial: sifive: Change include order
Like clk_get_by_index, there is requirement for
clk_get_by_index_nodev. In this case to make common
code functionalities for dev and nodev, clk_get_by_index
is trying to get the index of clock by passing ofnode
instead of actual dev like current gpio uclass does.
In these scenarios with current order of include files
the serial_sifive driver is unable to find CONFIG_ENV_SIZE.
In file included from arch/riscv/include/asm/u-boot.h:23:0,
from include/dm/of.h:10,
from include/dm/ofnode.h:12,
from include/clk.h:11,
from drivers/serial/serial_sifive.c:6:
include/environment.h:145:19: error: 'CONFIG_ENV_SIZE'
undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'?
#define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE)
So, fix consists of changing the order of include files
in serial_sifive.c to include first common.h file.
Cc: Anup Patel <Anup.Patel@wdc.com> Cc: Rick Chen <rick@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 8 May 2019 14:22:18 +0000 (19:52 +0530)]
clk: sifive: fu540-prci: Change include order
Like clk_get_by_index, there is requirement for
clk_get_by_index_nodev. In this case to make common
code functionalities for dev and nodev, clk_get_by_index
is trying to get the index of clock by passing ofnode
instead of actual dev like current gpio uclass does.
In these scenarios with current order of include files
the fu540-prci driver is unable to find CONFIG_ENV_SIZE.
In file included from arch/riscv/include/asm/u-boot.h:23:0,
from include/dm/of.h:10,
from include/dm/ofnode.h:12,
from include/clk.h:11,
from include/clk-uclass.h:13,
from drivers/clk/sifive/fu540-prci.c:32:
include/environment.h:145:19: error: 'CONFIG_ENV_SIZE'
undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'?
#define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE)
So, fix consists of changing the order of include files
in fu540-prci.c to include first common.h file.
Cc: Anup Patel <Anup.Patel@wdc.com> Cc: Rick Chen <rick@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 8 May 2019 14:12:16 +0000 (19:42 +0530)]
spi: atcspi200: Change include order
Like clk_get_by_index, there is requirement for
clk_get_by_index_nodev. In this case to make common
code functionalities for dev and nodev, clk_get_by_index
is trying to get the index of clock by passing ofnode
instead of actual dev like current gpio uclass does.
In these scenarios with current order of include files
the atcspi200_spi driver is unable to find CONFIG_ENV_SIZE.
In file included from arch/nds32/include/asm/u-boot.h:24,
from include/dm/of.h:10,
from include/dm/ofnode.h:12,
from include/clk.h:11,
from drivers/spi/atcspi200_spi.c:9:
include/environment.h:145:19: error: 'CONFIG_ENV_SIZE'
undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'?
#define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE)
So, fix consists of changing the order of include files
in atcspi200_spi.c to include first common.h file.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tom Rini [Wed, 8 May 2019 13:20:19 +0000 (09:20 -0400)]
Merge git://git.denx.de/u-boot-x86
- Allow x86 boards to use TPL, SPL and U-Boot proper
- Update sysreset x86 driver to utilize ACPI registers to do power off
- Add a new chromebook_samus_tpl board for TPL support
- Several minor changes in binman tool
Simon Glass [Wed, 8 May 2019 03:41:16 +0000 (21:41 -0600)]
x86: samus: Add a target to boot through TPL
Add a version of samus which supports booting from TPL to SPL and then
to U-Boot. This allows TPL to select from an A or B SPL to support
verified boot with field upgrade.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 2 May 2019 16:52:20 +0000 (10:52 -0600)]
x86: Update device tree for Chromium OS verified boot
The standard image generated by U-Boot on x86 is u-boot.rom. Add a
separate image called image.bin for verified boot. This supports
verification in TPL of which SPL/U-Boot to start, then jumping to the
correct one, with SPL setting up the SDRAM and U-Boot proper providing
the user interface if needed.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 2 May 2019 16:52:19 +0000 (10:52 -0600)]
x86: Update device tree for TPL
Add TPL binaries to the device x86 binman desciption. When enabled, TPL
will start first, doing the 16-bit init, then jump to SPL and finally
U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 2 May 2019 16:52:16 +0000 (10:52 -0600)]
x86: Add documentation on the samus flashmap
There are quite a few variables which control where things appear in the
final ROM image. Add a flashmap in the documentation to make this easier
to figure out.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: squashed "x86: Update the memory map a little" in]
[bmeng: fixed typo of 'documentation' in the commit title] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 26 Apr 2019 03:59:08 +0000 (21:59 -0600)]
x86: Support PCI VGA ROM when TPL is used
When TPL is in use, U-Boot proper should support initing the VGA ROM even
though the 32-bit init portion is in SPL. Update the condition to handle
this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 2 May 2019 16:52:15 +0000 (10:52 -0600)]
x86: sysreset: Implement the get_last() method
Add a default implementation of this method which always indicates that
the last reset was a power-on reset. This is the most likely type of reset
and without a PCH-specific driver we cannot determine any other type.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 2 May 2019 16:52:13 +0000 (10:52 -0600)]
x86: sysreset: Separate out the EFI code
The EFI implementation of reset sits inside the driver and is called
directly from outside the driver, breaking the normal driver-model
conventions. Worse, it passed NULL as the device pointer, hoping that
the called function won't use it, which breaks as soon as code is added
to use it.
Separate out the implementation to improve the situation enough to allow
a future patch to add new sysreset features.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 26 Apr 2019 03:58:57 +0000 (21:58 -0600)]
x86: Support saving MRC data from SPL
When SPL is used to set up the memory controller we want to save the MRC
data in SPL to avoid needing to pass it up to U-Boot proper to save. Add a
function to handle that.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 26 Apr 2019 03:58:54 +0000 (21:58 -0600)]
x86: broadwell: Allow booting from SPL
At present broadwell only supports booting straight into U-Boot proper.
Add a separate init file to boot from SPL into U-Boot proper, and select
it when SPL is in use.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 26 Apr 2019 03:58:51 +0000 (21:58 -0600)]
x86: broadwell: Split CPU init
Split the CPU init into two parts - the 'full' init which happens in the
first U-Boot phase, and the rest of the init that happens on subsequent
stages.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 26 Apr 2019 03:58:50 +0000 (21:58 -0600)]
x86: broadwell: Move init of debug UART to cpu.c
At present the debug UART is set up in sdram.c which is not the best place
since it has nothing in particular to do with SDRAM. Since we want to
support initing this in SPL too, move it to a common file.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: added 'broadwell' tag in the commit title] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 26 Apr 2019 03:58:49 +0000 (21:58 -0600)]
x86: broadwell: Allow SDRAM init from SPL
At present, for broadwell, SDRAM is always set up in U-Boot proper since
the 64-bit mode (which uses SDRAM init in SPL) is not supported.
Update the code to allow SDRAM init in SPL instead so that U-Boot proper
can be loaded into SDRAM and run from there. This allows U-Boot to be
compressed to reduce space, since it is not necessary to run it directly
from flash. It could later allow us to support 64-bit U-Boot on broadwell.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 26 Apr 2019 03:58:46 +0000 (21:58 -0600)]
x86: Support booting with TPL
Some boards want to use TPL as the first phase of U-Boot. This allows
selection of A or B SPL phases, thus allowing the memory init to be
upgraded in the field.
Add a new Kconfig option for this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 26 Apr 2019 03:58:42 +0000 (21:58 -0600)]
x86: Add a way to reinit the cpu
We cannot init the CPU fully both than once during a boot. Add a new
function which can be called to figure out the CPU identity, but which
does not change anything. For x86_64, this is empty for now.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Unfortunately this has a dramatic impact on the pre-relocation memory
used on x86 platforms (increasing it by 2KB) since it increases the
overhead for each PCI device from 220 bytes to 412 bytes.
This means that all PCI devices have the controller struct associated
with them. The solution is to move the regions[] member out of the array,
makes its size dynamic, or split UCLASS_PCI into controllers and
non-controllers, as the comment suggests.
For now, revert the commit to get things running again.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 26 Apr 2019 03:58:38 +0000 (21:58 -0600)]
spl: Allow sandbox to build a device-tree file
At present only OF_SEPARATE is considered valid for building a device-tree
file in SPL. However sandbox uses OF_HOSTFILE instead. Update the logic to
handle this and make it easier to understand.
Note that the new logic is not quite the same as the old logic. It was
previously assumed that checking for:
producing 'yy' meant that the first two were 'y' and the last was empty.
Strictly speaking it would be possible for any two of the three to be 'y'
and still yield the same result. However, that was not the intention of
the new logic, since OF_PLATDATA always ensures that no device-tree file
is included. So in effect the new logic is the same, with the addition of
OF_HOSTFILE as an option for OP_SEPARATE.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 26 Apr 2019 03:58:39 +0000 (21:58 -0600)]
binman: Allow sections to have an offset
At present sections are always placed automatically. Even if an 'offset'
property is provided it is ignored. Update the logic to support an offset
for sections.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 26 Apr 2019 03:58:34 +0000 (21:58 -0600)]
binman: Don't show image-skip message by default
This message is not very important since it is simply indicating that the
user's instructions are being followed. Only show it when the verbosity
level is above the default.
Also drop the unnecessary extra newline on this message, which causes two
line breaks.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 26 Apr 2019 03:58:33 +0000 (21:58 -0600)]
binman: Don't generate an error in 'text' entry constructor
It is not good practice to raise an exception in a constructor. In this
case the 'text' entry may not actually be used, if -i is used to filter
out the images that get built.
Move the exception to where the data is actually used.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Chris Brandt [Wed, 23 Aug 2017 19:53:59 +0000 (14:53 -0500)]
ARM: dts: renesas: Add RZ/A1 GR-Peach board
Add board code and DTs for Renesas RZ/A1 SoC-based GR-Peach,
which is a cheap development platform with RZ/A1H SoC. The
DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Currently supported are UART, ethernet and RPC SPI. The board
can be booted from RPC SPI by writing the u-boot.bin binary
to the beginning of the SPI NOR, e.g. using the "sf" command.
The board can also be booted via JTAG by setting text base to
0x20020000, loading u-boot.bin there via JTAG and executing it
from that address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Chris Brandt <chris.brandt@renesas.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
projects / u-boot.git / log