York Sun [Wed, 29 Feb 2012 12:36:51 +0000 (12:36 +0000)]
powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
P1010RDB and p1_pc_rdb_pc has incorrect configuration for
CONFIG_DDR_RAW_TIMING. It should be CONFIG_SYS_DDR_RAW_TIMING.
Incorrect setting causes DDR failure in case of SPD absent.
Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
powerpc/85xx:Avoid hardcoded vector address for IVORs
For e500 and e500v2 architecturees processor IVPR address should be alinged on
64K boundary.
in start.S, CONFIG_SYS_MONITOR_BASE is stored blindly in IVPR assuming it to be
64K aligned. It may not be true always. If it is not aligned, IVPR + IVORs may
not point to an exception handler.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Chunhe Lan [Wed, 18 Apr 2012 20:58:56 +0000 (15:58 -0500)]
powerpc/p1023rds: Disable nor flash node and enable nand flash node
In the p1023rds, when system boots from nor flash, kernel only accesses nor
flash and can not access nand flash with BR0/OR0; when system boots from
nand flash, kernel only accesses nand flash and can not access nor flash
with BR0/OR0.
Default device tree nor and nand node should have the following structure:
Stephen Warren [Thu, 19 Apr 2012 11:09:49 +0000 (11:09 +0000)]
arm: restore fdt_fixup_ethernet call to do_bootm_linux
Commit 0a672d4 "arm: Add Prep subcommand support to bootm" re-organized
do_bootm_linux for ARM. During the re-organization, the call to
fdt_fixup_ethernet() was removed. I assume this was useful, so add it
back.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Tom Rini <trini@ti.com>
Stephen Warren [Thu, 19 Apr 2012 11:34:00 +0000 (11:34 +0000)]
arm: fix bootm with device tree
Commit 0a672d4 "arm: Add Prep subcommand support to bootm" re-organized
do_bootm_linux() for ARM. During the re-organization, the code to pass
the device tree to the kernel was removed. Add it back. This restores
the ability to boot a kernel using device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Tom Rini <trini@ti.com> Acked-by: Allen Martin <amartin@nvidia.com> Tested-by: Allen Martin <amartin@nvidia.com>
Timo Ketola [Sun, 22 Apr 2012 23:57:27 +0000 (23:57 +0000)]
Fix the behaviour of the 'run' command
If one command fails, 'run' command should terminate and not execute
any remaining variables.
Signed-off-by: Timo Ketola <timo@exertus.fi> Tested-by: Wolfgang Denk <wd@denx.de> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
Stephan Linz [Tue, 10 Apr 2012 06:20:57 +0000 (06:20 +0000)]
net: ll_temac: drop obsolete "NAMESIZE" define
... after commit "net/miiphy/serial: drop duplicate NAMESIZE
define" (sha1:f6add13) was applied. The building of the new
LL TEMAC network driver fails with error below:
xilinx_ll_temac.c: In function 'xilinx_ll_temac_initialize':
xilinx_ll_temac.c:301: error: 'NAMESIZE' undeclared (first use in this function)
xilinx_ll_temac.c:301: error: (Each undeclared identifier is reported only once
xilinx_ll_temac.c:301: error: for each function it appears in.)
Signed-off-by: Stephan Linz <linz@li-pro.net> Acked-by: Mike Frysinger <vapier@gentoo.org>
Simon Glass [Sat, 14 Jan 2012 15:12:45 +0000 (15:12 +0000)]
Add 'patman' patch generation, checking and submission script
What is this?
=============
This tool is a Python script which:
- Creates patch directly from your branch
- Cleans them up by removing unwanted tags
- Inserts a cover letter with change lists
- Runs the patches through checkpatch.pl and its own checks
- Optionally emails them out to selected people
It is intended to automate patch creation and make it a less
error-prone process. It is useful for U-Boot and Linux work so far,
since it uses the checkpatch.pl script.
It is configured almost entirely by tags it finds in your commits.
This means that you can work on a number of different branches at
once, and keep the settings with each branch rather than having to
git format-patch, git send-email, etc. with the correct parameters
each time. So for example if you put:
in one of your commits, the series will be sent there.
This is just a patch for the problem reported here:
http://lists.denx.de/pipermail/u-boot/2012-February/117580.html originally reported by Igor.
"Looks like this is copy paste error from my side,(for port2/3 it should have been bypass
for port2/3 rather its port1 set in bypass mode)"
I only submit the patch since it is missing in 2012.04-rc3 while the twister board
depends on it. Maybe it is already somewhere in the reposistory, but I cannot find it.
note: the twister boards still needs an additional `usb reset`, don't know why.
U-Boot 2012.04-rc3-dirty (Apr 19 2012 - 21:38:38)
AM35XX-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 600 Mhz
TAM3517 TWISTER Board + LPDDR/NAND
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: OMAP SD/MMC: 0
In: serial
Out: serial
Err: serial
Die ID #746c0000000000000155dc1405011024
Net: DaVinci-EMAC, smc911x-0
Hit any key to stop autoboot: 0
twister => usb start
(Re)start USB...
USB: Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
twister => usb reset
(Re)start USB...
USB: Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
twister => usb reset
(Re)start USB...
USB: Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
twister => usb reset
(Re)start USB...
USB: Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Wolfgang Denk [Thu, 19 Apr 2012 02:36:44 +0000 (02:36 +0000)]
fdt: avoid bad MAKEALL status
Current versions of dtc always print a message like
DTC: dts->dtb on file "dt.dtb.tmp"
which cannot even be suppressed with "-qqq". To avoid incorrect
MAKEALL status, we manually filter out this message. This is a bit
complicated, as we have to make sure to set a correct return code.
Also, get rid of the temp file: dtc accepts "-" for stdin.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
Wolfgang Denk [Thu, 19 Apr 2012 01:14:17 +0000 (01:14 +0000)]
GCC4.6: Squash warnings in onenand_base.c
Fix gcc 4.6 build warnings:
onenand_base.c: In function 'onenand_probe':
onenand_base.c:2577:6: warning: variable 'maf_id' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Wolfgang Denk [Wed, 18 Apr 2012 20:41:06 +0000 (22:41 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
* 'master' of git://git.denx.de/u-boot-sh:
sh: ecovec: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
sh: Fix rsk7264 pin setup for on-board ethernet
sh: ecovec: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
When calling board_late_init, we need to define CONFIG_BOARD_LATE_INIT.
The latest ecovec config defines BOARD_LATE_INIT, board_late_init is not called.
Do the same AXI cache and Qos settings done already in the
SabreLite imximage.cfg for the ARM2 board, too.
It fixes a display flash issue caused by low priority of
the display IDMA channel.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Jason Chen <b02280@freescale.com> CC: Jason Liu <r64343@freescale.com> CC: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <festevam@gmail.com> Acked-by: Jason Liu <r64343@freescale.com>
Wolfgang Denk [Mon, 16 Apr 2012 21:01:12 +0000 (23:01 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
ARM926EJS: Fix cache.c to comply with checkpatch.pl
ARM926EJS: Make asm routines volatile in cache ops
MX35: mx35pdk: wrong board revision
ARM1136: MX35: Make asm routines volatile in cache ops
ARM: add u-boot.imx as target for i.MX SOCs
M28: Pull out CONFIG_APBH_DMA so it's always enabled
DMA: Split the APBH DMA init into block and channel init
imx: Return gpio_set_value in gpio_direction_output
imx: Use GPIO_TO_PORT macro in the gpio driver instead of (gpio >> 5)
imx: Add GPIO_TO_PORT macro in the mxc_gpio driver
imx: Remove unneeded/repititive definitions from imx headers
i.MX28: Allow coexistence of PIO and DMA mode for SD/MMC
MX31: mx31pdk: drop enable_caches from board file
i.MX28: Fix initial stack pointer position
mx35: mx35pdk: fix when cache functions are linked
mx35: flea3: fix when cache functions are linked
ARM: 926ejs: use debug() for misaligned addresses
ARM1136: add cache flush and invalidate operations
mx6qsabrelite: Fix the serial console port
mx6qsabrelite: Add boot switch setting information into the README
i.MX6: mx6qsabrelite: add cache commands if cache is enabled
i.MX6: implement enable_caches()
i.MX6: define CACHELINE_SIZE
MX53: DDR: Fix ZQHWCTRL field TZQ_CS
mx28evk: Add a README file
mx28: Split the README into a common part and a m28 specific part
tricorder: Load kernel from ubifs
tricorder: Add UBIFS
cm-t35: fix Ethernet reset timing
hawkboard: Add CONFIG_SPL_LIBGENERIC_SUPPORT
BeagleBoard: Remove userbutton command and use gpio command instead
OMAP: Move omap1510inn to Unmaintained / Orphaned
Marek Vasut [Sun, 8 Apr 2012 17:34:46 +0000 (17:34 +0000)]
DMA: Split the APBH DMA init into block and channel init
This fixes the issue where mxs_dma_init() was called either twice or never,
without introducing any new init hooks.
The idea is to allow each and every device using the APBH DMA block to
configure and request only the channels it uses, instead of making it call init
for all the channels as is now.
The common DMA block init part, which only configures the block, is then called
from CPUs arch_cpu_init() call.
NOTE: This patch depends on:
http://patchwork.ozlabs.org/patch/150957/
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Marek Vasut [Thu, 5 Apr 2012 03:30:35 +0000 (03:30 +0000)]
i.MX28: Allow coexistence of PIO and DMA mode for SD/MMC
This SD DMA function of i.MX28 is still apparently too experimental to be
enabled by default in 2012.04 release. Enable this feature only if the user
plans to tinker with DCache or explicitly enables it.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
introduced usage of GENERATED_GBL_DATA_SIZE and calculation of initial stack
pointer position defived from that. Due to a small typo, the SP position moved
to 0x21f80, which is past the SRAM area. This didn't manifest on the real
hardware as the SRAM repeats there (address bits in the CPU being ignored).
Though this was caught in QEMU, where it crashed the emulator.
Misaligned warnings are useful to debug faulty drivers.
A misaligned warning is printed also when the driver
is correct - use debug() instead of printf().
Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Albert Aribaud <albert.u.boot@aribaud.net> CC: Mike Frysinger <vapier@gentoo.org> CC: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de>
ARM1136: add cache flush and invalidate operations
Since commit 5c1ad3e6f8ae578bbe30e09652f1531e9bc22031
(net: fec_mxc: allow use with cache enabled) the FEC_MXC
driver uses flush_dcache_range() and invalidate_dcache_range()
functions. This driver is also configured for ARM1136 based
'flea3' and 'mx35pdk' boards which currently do not build
as there are no ARM1136 specific flush_dcache_range() and
invalidate_dcache_range() functions. Add various ARM1136
cache functions to fix building for 'flea3' and 'mx35pdk'.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> CC: Mike Frysinger <vapier@gentoo.org> CC: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de>
Bernhard Walle [Tue, 3 Apr 2012 00:37:03 +0000 (00:37 +0000)]
tricorder: Add UBIFS
Since kernel should be in a ubifs partition, we need UBIFS.
The greater malloc size is needed for UBIFS.
Signed-off-by: Bernhard Walle <walle@corscience.de>
Squashed two commits (UBIFS enabled and malloc size increased) into one. Signed-off-by: Thomas Weber <weber@corscience.de>
Tom Rini [Wed, 28 Mar 2012 06:26:19 +0000 (06:26 +0000)]
OMAP: Move omap1510inn to Unmaintained / Orphaned
After removing omap1610inn for not building, move omap1510inn to
orphaned. Also update boards.cfg to note it's part of the 'omap' SoC to
make sure the board is built more often and future breakage noticed
quicker.
Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
mkenvimage.c: In function ‘main’:
mkenvimage.c:218: warning: format ‘%ld’ expects type ‘long int’, but argument 3 has type ‘unsigned int’
mkenvimage.c:226: warning: format ‘%ld’ expects type ‘long int’, but argument 3 has type ‘unsigned int’
Wolfgang Denk [Mon, 9 Apr 2012 19:34:27 +0000 (21:34 +0200)]
Merge branch 'marek.vasut@gmail.com' of git://git.denx.de/u-boot-staging
* 'marek.vasut@gmail.com' of git://git.denx.de/u-boot-staging:
LMB: Fix undefined lmb_reserve() on non-lmb platforms
MIPS: fix endianess handling
MIPS: fix inconsistency in config option for cache operation mode
MIPS: board.c: fix init of flash data in bd_info
Wolfgang Denk [Mon, 9 Apr 2012 15:10:01 +0000 (17:10 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-net
* 'master' of git://git.denx.de/u-boot-net:
net/designware: Change timeout loop implementation
net/designware: Set ANAR to 0x1e1
net/designware: Program phy registers when auto-negotiation is ON
net/designware: Try configuring phy on each dw_eth_init
net/designware: Consecutive writes must have delay
net/designware: Phy address fix
net/designware: Fix the max frame length size
net/designware: Fix to restore hw mac address
microblaze: Wire up LL_TEMAC driver initialization
microblaze: Add faked LL_TEMAC driver configuration
microblaze: Enable several ethernet driver compilation
net: ll_temac: Add LL TEMAC driver to u-boot
Update net subsystem maintainer in doc/git-mailrc
net/eth.c: fix eth_write_hwaddr() to use dev->enetaddr as fall back
mvgbe: remove warning for unused methods
Wolfgang Denk [Mon, 9 Apr 2012 15:07:50 +0000 (17:07 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-onenand
* 'master' of git://git.denx.de/u-boot-onenand:
onenand: samsung: Enable OneNAND support at Samsung's Exynos4210
onenand: Replace ONENAND_IS_MLC() with ONENAND_HAS_4KB()
onenand:samsung OneNAND chip probe functions added for GONI and Exynos4210
onenand:samsung Target dependent OneNAND chip probe function
Wolfgang Denk [Mon, 9 Apr 2012 15:00:45 +0000 (17:00 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-nios
* 'master' of git://git.denx.de/u-boot-nios:
nios2 - adjust gbl data off to account for bd_info
nios2: implement get_ticks and get_tbclk
nios2: add flush_dcache_range function
Marek Vasut [Sun, 1 Apr 2012 03:59:46 +0000 (03:59 +0000)]
LMB: Fix undefined lmb_reserve() on non-lmb platforms
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: Graeme Russ <graeme.russ@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
Vikas Manocha [Mon, 26 Mar 2012 00:09:57 +0000 (00:09 +0000)]
net/designware: Program phy registers when auto-negotiation is ON
If AN(auto-negotiation) is ON, speed bit of control register are not
applicable. Also phy registers were not getting programmed as per the
result of AN. This patch sets only AN bit & restart AN bit for AN ON
selection & programs PHY registers as per AN result.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
Vipin Kumar [Mon, 26 Mar 2012 00:09:56 +0000 (00:09 +0000)]
net/designware: Try configuring phy on each dw_eth_init
Phy autonegotiation works only when the ethernet cable is plugged in.
Since the phy was configured only at the init time, a plugged in cable
was necessary to initialize the phy properly.
This patch keeps a flag to check if the phy initialization has
succeeded, and calls configure_phy routine at every init if this flag
reports otherwise.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
Armando Visconti [Mon, 26 Mar 2012 00:09:55 +0000 (00:09 +0000)]
net/designware: Consecutive writes must have delay
This patch solves a TX/RX problem which happens at 10Mbps, due to the
fact that we are not respecting 4 cyles of the phy_clk (2.5MHz) between
two consecutive writes on the same register.
Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
Vipin KUMAR [Mon, 26 Mar 2012 00:09:53 +0000 (00:09 +0000)]
net/designware: Fix the max frame length size
The max frame length for normal descriptor can be 0x7FF i.e 2047. It was wrongly
specified as 2048. Currently, the max descriptor length is around 1500, so
redefining the mask to 1600
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
Vipin KUMAR [Mon, 26 Mar 2012 00:09:52 +0000 (00:09 +0000)]
net/designware: Fix to restore hw mac address
The network controller mac resets hardware address stored in MAC_HI and MAC_LO
registers if mac is resetted. So, hw mac address needs to be restored in case
mac is explicitly resetted from driver.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
Expand the specific configuration for the microblaze-generic
board in xparameters.h with a faked setup to enable the
LL_TEMAC driver.
Note: From now the microblaze-generic board is no longer a
valid board configuration for a real piece of hardware. Rather
than, we use the file config.mk and xparameters.h as a faked
board configuration to force the compilation of all potential
driver code for Microblaze systems.
Eric Miao [Wed, 18 Jan 2012 22:56:33 +0000 (22:56 +0000)]
net/eth.c: fix eth_write_hwaddr() to use dev->enetaddr as fall back
Ignore the return value of eth_getenv_enetaddr_by_index(), and if it
fails, fall back to use dev->enetaddr, which could be filled up by
the ethernet device driver:
With the current code, introduced with below commit, eth_write_hwaddr()
will fail immediately if there is no eth<n>addr in the environment variables.
However, e.g. for an overo based product that uses the SMSC911x ethernet
chip (with the MAC address set via EEPROM connected to the SMSC911x chip),
the MAC address is still OK.
On mx28 boards that are depending on the OCOTP bits to set the MAC address
(like the Denx m28 board), the OCOTP bits should be used instead of
failing on the environment variables.
Signed-off-by: Eric Miao <eric.miao@linaro.org> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Stefan Roese <sr@denx.de> CC: Eric Miao <eric.miao@linaro.org> CC: Wolfgang Denk <wd@denx.de> CC: Philip Balister <philip@balister.org> CC: Zach Sadecki <zach@itwatchdogs.com>
Stefan Bigler [Mon, 26 Mar 2012 00:02:13 +0000 (00:02 +0000)]
mvgbe: remove warning for unused methods
Some baords may use the GBE interface but they have no
phy connected to the interface and a direct MAC/MAC interface.
For them we need to get rid of compiler warnings.
Marek Vasut [Sun, 1 Apr 2012 03:59:46 +0000 (03:59 +0000)]
LMB: Fix undefined lmb_reserve() on non-lmb platforms
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: Graeme Russ <graeme.russ@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
Boards with CONFIG_SYS_NO_FLASH should not forced to define
CONFIG_SYS_FLASH_BASE. In this case the flash data in bd_info
should be initialized with 0 like the other archs do.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
net/altera_tse: use flush_dcache_range instead of flush_dcache
flush_dcache is not declared in the common.h API,
flush_dcache_range however is
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Thomas Chou <thomas@wytron.com.tw> Acked-by: Thomas Chou <thomas@wytron.com.tw>
net/ethoc: use flush_dcache_range instead of flush_dcache
flush_dcache is not declared in the common.h API,
flush_dcache_range however is
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Thomas Chou <thomas@wytron.com.tw> Acked-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: albert.u.boot@aribaud.net Cc: afleming@gmail.com Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@nvidia.com> Cc: Nicolas Pitre <nico@fluxnic.net> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
projects / u-boot.git / log