Peng Fan [Tue, 16 Oct 2018 04:50:30 +0000 (04:50 +0000)]
tools: add i.MX8/8X image support
i.MX8/8X bootable image type is container type.
The bootable image, containers a container set which supports two
container. The 1st container is for SECO firmware, the 2nd container
needs to include scfw, m4_0/1 image, ACore images per your requirement.
Peng Fan [Thu, 18 Oct 2018 22:26:23 +0000 (00:26 +0200)]
serial: lpuart: support uclass clk api
Modify most APIs to use udevice as the first parameter, then
it will be easy to get the clk reference by using udevice pointer.
Use uclass api to get lpuart clk when CONFIG_CLK is enabled.
Peng Fan [Thu, 18 Oct 2018 12:28:31 +0000 (14:28 +0200)]
serial_lpuart: Update lpuart driver to support i.MX8
Add i.MX8 compatible string and cpu type support to lpuart driver,
to use little endian 32 bits configurations.
Also, according to RM, the Receive FIFO Enable (RXFE) field in LPUART
FIFO register is bit 3, so this definition should change to 0x08
(not 0x40) for i.MX8, otherwise the Receive FIFO is not disabled.
Peng Fan [Thu, 18 Oct 2018 12:28:29 +0000 (14:28 +0200)]
power: Add power domain driver for i.MX8
Add the power domain DM driver for i.MX8, that it depends on the DTB
power domain trees to generate the power domain provider devices. Users
need to add power domain trees with property "compatible = "nxp,imx8-pd";"
When power on a PD device, the driver will power on its ancestor PD
devices in power domain tree.
When power off a PD device, the driver will check its child PD devices
first. Only if all child PD devices are off, then power off the current PD
device. Then the driver checks sibling PD devices. If sibling PD devices
are off, then it will power off parent PD device.
There is no counter maintained in this driver, but a state to hold current
on/off state. So the request and free functions are empty.
The power domain implementation in i.MX8 DTB set the "#power-domain-cells"
to 0, so there is no ID binding with each PD device. We don't use "id"
variable in struct power_domain. At the same time, we have to set of_xlate
to empty to bypass standard of_xlate in uclass driver.
Peng Fan [Thu, 18 Oct 2018 12:28:28 +0000 (14:28 +0200)]
pinctrl: Add pinctrl driver for i.MX8
Add pinctrl driver for i.MX8. The pads configuration is controlled
by SCU, so need to ask SCU to configure pads through scfw API.
Add pinctrl-scu to invoke sc_pad_set to configure pads.
Add a new flag IMX8_USE_SCU to differentiate i.MX8 from other platforms
which could directly configure pads from Acore side.
Add CONFIG_PINCTRL_IMX8 as the built gate.
print_cpuinfo() in board init code requires uclass CPU driver,
add it to be able to display CPU info when CONFIG_DISPLAY_CPUINFO
option is enabled. CPU node in DT will have to include 'clocks'
and 'u-boot,dm-pre-reloc' properties for generic print_cpuinfo()
to work as expected. The driver outputs info for i.MX8QXP Rev A
and Rev B CPUs.
Commit 9faa43c4b5e5 ("ARM: dts: i.MX6UL: U-Boot specific dts for u-boot,
dm-spl") removes the u-boot,dm-spl properties from the imx6ul.dtsi file
and breaks the OPOS6UL board.
Add the u-boot,dm-spl properties into *-u-boot.dts files to make the
board boot again.
Fixes: commit 9faa43c4b5e5 ("ARM: dts: i.MX6UL: U-Boot specific dts for u-boot, dm-spl") Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
colibri_imx7: prime get_ram_size() using imx_ddr_size()
Rather than passing a hardcoded maxsize to the generic get_ram_size()
function use the i.MX 7 specific imx_ddr_size() function, which extracts
the memory size at runtime by reading the DDR controller registers.
This is a purely cosmetic change as the generic get_ram_size() function
already took care of properly automatically detecting 256MB, 512MB or 1GB
modules.
imx: mx7: fix potential overflow in imx_ddr_size()
The imx_ddr_size() function may overflow as it is possible to kind of
over provision the DDR controller. Fix this by capping it to 2 GB which
is the maximum allowed size as per reference manual.
Otavio Salvador [Fri, 28 Sep 2018 14:22:37 +0000 (11:22 -0300)]
pico-imx6ul, pico-imx7d: Enable USB and PXE boot support
This allow the use of a USB storage or PXE network booting as
fallback, allowing for example for manufacturing installation of eMMC
storage in an easy way.
Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Otavio Salvador [Fri, 28 Sep 2018 14:22:36 +0000 (11:22 -0300)]
pico-imx6ul, pico-imx7d: Use eMMC user partition by default
After discussing with TechNexion about how its default setting, it is
better to install on the eMMC user partition by default, when using
DFU, so it works out of box for majority of users.
Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
test_avb: Update pymark.buildconfigspec information for the AVB tests
Update the pymark.buildconfigspec to depend on 'cmd_mmc' in addition to
'cmd_avb' for those tests that needs more a more complete MMC
implementation or the "mmc" command.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
[trini: initialize session to 0 in dm_test_tee] Signed-off-by: Tom Rini <trini@konsulko.com>
Adds a sandbox tee driver which emulates a generic TEE with the OP-TEE
AVB TA.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Fix printf warnings in ta_avb_invoke_func, slots is uint] Signed-off-by: Tom Rini <trini@konsulko.com>
Adds configuration option OPTEE_TA_AVB and a header file describing the
interface to the Android Verified Boot 2.0 (AVB) trusted application
provided by OP-TEE.
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org> Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
* Targets ARM and ARM64
* Supports using any U-Boot memory as shared memory
* Probes OP-TEE version using SMCs
* Uses OPTEE message protocol version 2 to communicate with secure world
Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Adds a uclass to interface with a TEE (Trusted Execution Environment).
A TEE driver is a driver that interfaces with a trusted OS running in
some secure environment, for example, TrustZone on ARM cpus, or a
separate secure co-processor etc.
The TEE subsystem can serve a TEE driver for a Global Platform compliant
TEE, but it's not limited to only Global Platform TEEs.
The over all design is based on the TEE subsystem in the Linux kernel,
tailored for U-Boot.
Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Prior to this patch was do_avb_write_rb() reading supplied rb_idx as a
hexadecimal number while do_avb_read_rb() printed the read out rb_idx as
decimal number. For consistency change do_avb_read_rb() to print rb_idx
as a hexadecimal number too.
Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Michal Simek [Thu, 4 Oct 2018 07:29:20 +0000 (09:29 +0200)]
spl: ram: Fix u_boot_pos calculation
The patch:
"spl: Weed out CONFIG_SYS_TEXT_BASE usage"
(sha1: 04ce5427bd3914cab8be78513275a20ab878520a)
introduced bug where assigning to u_boot_pos variable wasn't done
which end up in situation where SPL wasn't able to find out
image on the selected address.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With there now being four device tree files, and 4 separate
defconfig files, the code necessary to determine which board is
being used is no longer necessary as the corresponding pin-muxing
and board names are determined by the device tree.
Adam Ford [Sat, 29 Sep 2018 19:10:18 +0000 (14:10 -0500)]
ARM: DTS: Add Logic PD OMAP35/DM37 SOM-LV and OMAP35 Torpedo
With the device trees doing most of the work of pin-muxing and
DM doing much of the peripheral initialization, this creates
new defconfig files for each of the Logic PD variants with
proper register settings/pin-muxing.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update MAINTAINERS entry] Signed-off-by: Tom Rini <trini@konsulko.com>
Adam Ford [Sat, 29 Sep 2018 19:10:17 +0000 (14:10 -0500)]
ARM: DTS: Add support for Logic PD OMAP35 Torpedo & SOM-LV
The baseboards and SOM's are virtually identical to their DM37
counterparts, but OMAP36/37 and OMAP3 have some minor register
differences. With the boards being mostly driven by device trees
now, this synchronizes their respective device trees with linux-omap
for-next branch destined for 4.20 (or whatever the version after 4.19
will be called)
Adam Ford [Sat, 29 Sep 2018 19:10:16 +0000 (14:10 -0500)]
ARM: DTS: Remove unnecessary u-boot.dtsi options from omap3/36xx
With the introduction of the omap serial driver, the need for some
of these U-Boot specific modifications is gone. This cleans up
this unnneeded stuff.
misc: Add support for the Arm Versatile Express config bus
Add support for the Arm Versatile Express config bus that is
being used for exposing various subsystems via a generic
configuration bus. This driver adds support for generating
transactions on this configuration bus and can be used by
other drivers to abstract the communication with the actual
function providers.
Instead of manually specifying CONFIG_SYS_EXTRA_ENV_RELOC
for every board that needs it, it shouldn't hurt to let
initr_reloc_global_data() always relocate gd->env_addr
unless we know this pointer is outside the initial binary.
To achieve this, the relocation is omitted if
CONFIG_ENV_ADDR is defined (and ENV_IS_EMBEDDED is not).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Stephen Warren [Thu, 20 Sep 2018 22:55:03 +0000 (16:55 -0600)]
test/py: ignore console read exceptions after test failure
After a test has failed, test/py drains the U-Boot console log to ensure
that any relevant output is captured. At this point, we don't care about
detecting any additional errors, since the test is already known to have
failed, and U-Boot will be restarted. To ensure that the test cleanup code
is not interrupted, and can correctly terminate the log sections for the
failed test, ignore any exception that occurs while reading the U-Boot
console output during this limited period of time.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tom Rini [Fri, 5 Oct 2018 14:16:46 +0000 (10:16 -0400)]
Merge tag 'rockchip-for-v2018.11-rc2' of git://git.denx.de/u-boot-rockchip
Rockchip-focused changes for v2018.11-rc2:
- fixes to rkimage for SPL boot via USB
- fixes to make_fit_atf.py, incl. entry-point calculation and python3
compatibility
- OP-TEE support for ARMv7-based SoCs
- fixes to RGMII/GMII selection on the RK3328
Tom Rini [Fri, 5 Oct 2018 14:16:31 +0000 (10:16 -0400)]
Merge tag 'arc-updates-for-2018.11-rc2' of git://git.denx.de/u-boot-arc
Here we do a couple of impovements for all ARC boards
as well as introduce yet another developemnt board.
1. Now for ARC boards we print CPU and board info
which is useful for users and helps with
analysis of logs "post-mortem".
2. Synopsys IoT development kit support is added
This one might bw a bit too late as we're past RC1
but:
1) This doesn't affect any other arches etc
as we change purely ARC code.
2) I've got a chance to talk about U-Boot on
IoT platforms during ELCE (my proposal was on
a wait list and only this week I've got
an update and invitation to talk) so it would
be good to have this board as a primer in upstream
code-base by the time of ELCE 2018.
3) For complete support of IoT devkit I'm yet to
significantly rework regmap subsystem in U-Boot
but that's a different topic and hopefully it will
be done sometime soon... though not this release
cycle for sure.
Alexey Brodkin [Wed, 24 Jan 2018 18:37:14 +0000 (21:37 +0300)]
arc: Add support for IoT development kit
The DesignWare ARC IoT Development Kit is a versatile platform
that includes the necessary hardware and software to accelerate
software development and debugging of sensor fusion,
voice recognition and face detection designs.
More information is avaialble here [1] and here [2].
The board is based on real silicon with
ARC EM9D-based Data Fusion IP Subsystem.
It sports a rich set of I/O including
* DW USB OTG
* DW MobileStorage (used for micro SD-card)
* GPIO
* multiple serial interface including DW APB UART
* ADC, PWM and eFlash, SRAM and SPI Flash memory
* Real-Time Clock (RTC)
* Bluetooth module with worldwide regulatory compliance
(FCC, IC, CE, ETSI, TELEC)
* On-board 9-axis sensor (gyro, accelerometer and compass)
Extensible with Arduino, Pmod, mikroBUS connectors and a 2x18
extension header.
One of the most interesting features for developers is built-in
Digilent USB JTAG probe so only micro-USB cable is needed!
Alexey Brodkin [Mon, 1 Oct 2018 08:48:47 +0000 (11:48 +0300)]
ARC: Don't pre-define CROSS_COMPILE
Even though arc-linux- prefix is used in ARC prebuilt tools and
in Buildroot there're other options like Linux distro cross-tools
etc where prefix is different so let's not rely on this default.
Daniel Gröber [Thu, 4 Oct 2018 13:32:42 +0000 (15:32 +0200)]
rockchip: Fix rkimage format for SPL boot over USB
The 'rkimage' format used for booting rockchip boards over USB seems to
have been broken since commit 7bf274b9caab ("rockchip: mkimage: use
imagename to select spl hdr & spl size"). That commit adds an offset of
RK_SPL_HDR_START(=2048) to the location the 'RKxx' header is written
at. However the bootrom expects this header to be the first four bytes of
the image, not at offset 2048. This appears to have been a copy paste
error since the 'rksd' and 'rkspi' image types do require this offset.
Furthermore commit 111bcc4fb6cb ("rockchip: mkimage: pad the header to
8-bytes (using a 'nop') for RK3399"), commit 3d54eabcafec9 ("rockchip:
spl: RK3399: use boot0 hook to create space for SPL magic") and
commit 308277569229 ("rockchip: mkimage: update rkimage to support
pre-padded payloads") changed the way the space for the 'RKxx' header is
allocated and written to the image without adjusting 'rkimage'.
This commit fixes those mistakes and makes it possible to load u-boot SPL
over USB once more.
(Tested on RK3399)
Signed-off-by: Daniel Gröber <daniel@dps.uibk.ac.at> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Andreas Färber [Sun, 3 Jun 2018 05:23:58 +0000 (07:23 +0200)]
rockchip: make_fit_atf.py depends on u-boot
u-boot.itb depends on u-boot-nodtb.bin, which in turn depends on u-boot.
u-boot.its from Rockchip make_fit_atf.py (used by {evb,firefly}-rk3399)
wants to read u-boot but is lacking this dependency, so that u-boot.itb
cannot be built in one go. Detect its use and add the missing dependency.
Reported-by: Yousaf Kaukab <yousaf.kaukab@suse.com> Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Janine Hagemann [Tue, 28 Aug 2018 06:25:04 +0000 (08:25 +0200)]
net: gmac_rockchip: Fix a register write in rk3328_gmac_set_to_rgmii
We have to use RK3328_RXCLK_DLY_ENA_GMAC_ENABLE instead of
RK3328_RXCLK_DLY_ENA_GMAC_MASK in rk3328_gmac_set_to_rgmii()
to enable the RX delay.
The MASK was used in a wrong way.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de> Reviewed-by: Philipp Tomisch <philipp.tomisch@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
make_fit_atf.py uses physical address of first segment as the
entry point to bl31. It is incorrect and causes following abort
when bl31_entry() is called:
Kever Yang [Thu, 23 Aug 2018 09:18:00 +0000 (17:18 +0800)]
rockchip: add fit source file for pack itb with op-tee
We package U-Boot and OP-TEE into one itb file for SPL,
so that we can support OP-TEE in SPL.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Thu, 23 Aug 2018 09:17:59 +0000 (17:17 +0800)]
spl: add support to booting with OP-TEE
OP-TEE is an open source trusted OS, in armv7, its loading and
running are like this:
loading:
- SPL load both OP-TEE and U-Boot
running:
- SPL run into OP-TEE in secure mode;
- OP-TEE run into U-Boot in non-secure mode;
To make code simple, it would be fine to use IH_OS_TEE for the
os tyle in TPL(just like IH_OS_LINUX is using both in SPL and U-Boot).
Here is the diagram for SPL loading OP-TEE,
IH_OS_TEE:(make u-boot.itb for SPL)
Non-Secure Secure
BootROM
|
v
SPL
|
v
--------- OP-TEE
|
v
U-Boot
|
V
Linux
For other two king of OP-TEE loading/booting, see commit message: 45b55712d4 image: Add IH_OS_TEE for TEE chain-load boot
More detail:
https://github.com/OP-TEE/optee_os
and search for 'boot arguments' for detail entry parameter in:
core/arch/arm/kernel/generic_entry_a32.S
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Patch fix warning:
/builddir/BUILD/u-boot-2018.05-rc2/"arch/arm/mach-rockchip/make_fit_atf.py" \
arch/arm/dts/rk3399-firefly.dtb > u-boot.its
./tools/mkimage -f u-boot.its -E u-boot.itb >/dev/null && cat
/dev/null
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/uboot@1
has a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@1 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@2 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@3 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/fdt@1 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node
/configurations/config@1 has a unit name, but no reg property
make[1]: Leaving directory
'/builddir/BUILD/u-boot-2018.05-rc2/builds/firefly-rk3399'
Reported-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
projects / u-boot.git / log