Alex Marginean [Fri, 10 Jan 2020 23:05:40 +0000 (01:05 +0200)]
arch: armv8: fsl-layerscape: export serdes config to environment
Exports the serdes configuration as an environment variable for LS gen 3
SoCs, so it can be used in u-boot command line. It should particularly
be useful for applying Linux DT overlays for the given serdes
configuration.
This code is called from arch_misc_init and not from the existing
serdes_init function because it depends on U-Boot environment being set
up.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Alex Marginean [Fri, 10 Jan 2020 23:05:39 +0000 (01:05 +0200)]
board: fsl: ls1028a: free up arch_misc_init
Currently LS1028A board code uses arch_misc_init to set up the board mux
on QDS. Move this code to misc_init_r. This is consistent with LS gen 2
and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Alex Marginean [Fri, 10 Jan 2020 23:05:36 +0000 (01:05 +0200)]
board: fsl: lx2160a: free up arch_misc_init
Currently LX2 board code uses arch_misc_init to set up the board mux on
RDB and QDS. Move this code to misc_init_r. This is consistent with LS
gen 2 and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Alex Marginean [Fri, 10 Jan 2020 21:51:32 +0000 (23:51 +0200)]
armv8: ls1028a_serdes: Add few missing serdes protocols
Add serdes protocol 0x7777, 0x9999, 0xb998, 0xbb56 to supported list.
These protocols are supported and functional but they trigger a warning
in U-Boot console at boot because they are not on this list.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Alex Marginean [Fri, 10 Jan 2020 21:32:20 +0000 (23:32 +0200)]
drivers: net: fsl_enetc: fix SXGMII MAC configuration
Separate MAC and serdes configuration, MAC configuration must be applied
at each enetc_start() as FLR clears it.
This restores traffic for ENETC interfaces in USXGMII mode.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The linux kernel Image is growing quite quickly,
if kernel Image size grow beyond 36 MB then
kernel Image at load address 0x81000000
overlaps with the reserved memory region
at 0x83400000.
Adjust kernel load address(kernel_addr_r) from
0x81000000 to 0x96000000 to avoid kernel Image
overlapping with reserved memory region.
This change fixes the below U-Boot error while
booting uncompressed kernel Image through booti command,
ERROR: reserving fdt memory region failed (addr=83400000 size=c00000)
Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Biwen Li [Fri, 10 Jan 2020 09:16:04 +0000 (17:16 +0800)]
include/configs: ls1012ardb: adjust kernel_addr_r
The linux kernel Image is growing quite quickly,
if kernel Image size grow beyond 36 MB then
kernel Image at load address 0x81000000
overlaps with the reserved memory region
at 0x83400000.
Adjust kernel load address(kernel_addr_r) from
0x81000000 to 0x96000000 to avoid kernel Image
overlapping with reserved memory region.
This change fixes the below U-Boot error while
booting uncompressed kernel Image through booti command,
ERROR: reserving fdt memory region failed (addr=83400000 size=c00000)
Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pramod Kumar [Thu, 9 Jan 2020 08:53:16 +0000 (08:53 +0000)]
armv8: fsl-layerscape: LS1044A/1048A: enable Only 1x 10GE port
LS1088A has four personalities, LS1088A, LS1084A, LS1048A and LS1044A.
LS1044A, LS1048A are LS1088A personalities, which support only one
1x 10GE port.
MAC1 and MAC2 are associated with 1G SGMII, 2.5G SGMII, and XFI.
Disable MAC1 to have only one 1x 10GE port for LS1044A, LS1048A.
Xiaowei Bao [Wed, 8 Jan 2020 06:29:54 +0000 (14:29 +0800)]
board/lx2160aqds: Update the DSPI status fixup
The dts node of the DSPI controller in kernel is spi instead of dspi,
it is not correct if use "/soc/dspi@" to fix up the status of the dts
in kernel, so, modify it to "/soc/spi@".
The DSPI2 and I2C5 are muxed, and the status of DSPI2 node in kernel dts
default value is okay, So set the status of DSPI2 node in kernel dts to
disabled if it is muxed as I2C5.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Wasim Khan [Mon, 6 Jan 2020 12:06:02 +0000 (12:06 +0000)]
configs: lx2160a: enable CONFIG_OF_BOARD_FIXUP for SECURE_BOOT defconfig
lx2160a rev1 and rev2 SoC has different pcie controller.
The pcie controller device tree node fields "compatible"
and registers names needs to be updated accordingly.
Enable CONFIG_OF_BOARD_FIXUP to apply board_fix_fdt
which updates the "compatible" and registers names.
Wasim Khan [Mon, 6 Jan 2020 12:06:00 +0000 (12:06 +0000)]
pci: layerscape: device tree fixup based on SoC and
lx2160a rev1 requires layerscape_gen4 device tree fixup and
lx2160a rev2 requires layerscape device tree fixup.
Add device tree fixup for lx2160a based on SoC and Version.
Michael Walle [Fri, 20 Dec 2019 13:16:48 +0000 (14:16 +0100)]
drivers: net: fsl_enetc: add write_hwaddr() for LS1028A
The LS1028A SoC is special in the handling of the MAC addresses. We need
to write to the IERB version of the PSIPMAR0/1 register. This value will
be sampled into the corresponding port PSIPMAR0/1 register if the PCI
memory access is enabled.
Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pramod Kumar [Fri, 20 Dec 2019 11:19:55 +0000 (11:19 +0000)]
board: ls1046afwry: Disable sgmii support
LS1046A SoC serdes protocol 0x3040 supports both sgmi and qsgmii,
however ls1046afrwy supports only qsgmii on board.
So, disable unsupported sgmii on board.
Hou Zhiqiang [Tue, 17 Dec 2019 10:10:40 +0000 (10:10 +0000)]
pci: layerscape: Fix the disabling of Expansion ROM BAR
The software will still get non-zero Expansion ROM BAR size
even when the BAR_EN bit is cleared. The BAR_EN bit of
register EXP_ROM_BAR_MASK_RC is not working as expected,
so this patch changes to mask all the bits.
Fixes: 80afc63fc342 ("pci: layerscape: add pci driver based on DM") Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Alex Marginean [Tue, 10 Dec 2019 14:55:39 +0000 (16:55 +0200)]
drivers: net: fsl_enetc: Pass on primary MAC address to Linux
Passes on the primary address used by u-boot to Linux. The code does a DT
fix-up for ENETC PFs and sets the primary MAC address in IERB. The address
in IERB is restored on ENETC PCI functions at FLR.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Holger Brunck [Fri, 10 Jan 2020 11:55:42 +0000 (12:55 +0100)]
km/scripts: product env and auto-reset for ramfs
This patch adds the possibility in both debug and ramfs modes to
optionally load an env file from /tftpboot/$tftppath (this is ignored if
not present, so the change is backward compatible). This gives the debug
and ramfs scripts the possibility to set uboot environment variables
that were previously asked the users to manually set (nfs path in debug
and rootfs size in ramfs).
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> CC: Tom Rini <trini@konsulko.com>
Rainer Boschung [Fri, 10 Jan 2020 11:47:43 +0000 (12:47 +0100)]
km/common: fix for CPUWD reset reason
The CPUWD reset reason is used for kmp204x.
And the qrio cpu reset request is configured to operate in
core reset mode.
But for the evaluation of the qrio's reset reason register
the CPUWD figures as a unit reset source rather than a core
reset source. This patch defines the CPUWD reset as a core
reset source when evaluating the reset reason register.
removing fdt_high from default set of variables for, dragonboard410c config
When using fitImage in AARCH64, the fdt is only 4 byte aligned.
According to linux kernel -> Documentation/arm64/booting.txt, the
fdt *must* be 8 byte aligned. Therefore, it is somewhat random,
if you build a kernel that the fdt is 4 or 8 byte aligned.
Removing fdt_high (or changing it to a valid 8 byte aligned
address) solves this issue.
cmd: pxe: execute the cls command only when supported
Execute the command cls (for clear screen), when the "menu background"
keyword is present in extlinux.conf file, only if the command is supported.
This patch avoid the warning "Unknown command 'cls'"
with "menu background" in extlinux.conf when CONFIG_CMD_BMP is activated
and CONFIG_CMD_CLS not activated (default for CONFIG_DM_VIDEO).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Stephan Gerhold [Sat, 4 Jan 2020 17:45:19 +0000 (18:45 +0100)]
board: Add new Samsung "stemmy" board based on ST-Ericsson U8500
The ST-Ericsson U8500 SoC has been used in mass-production for
some Android smartphones released around 2012.
In particular, Samsung has released more than 5 different
smartphones based on U8500, e.g.
- Samsung Galaxy S III mini (GT-I8190) "golden"
- Samsung Galaxy S Advance (GT-I9070) "janice"
- Samsung Galaxy Xcover 2 (GT-S7710) "skomer"
and a few others.
Mainline Linux has great support for the Ux500 SoC, so these
smartphones can also run Linux mainline quite well.
Unfortunately, the original Samsung bootloader used on these devices
has limitations that prevent booting Linux mainline directly.
It keeps the L2 cache enabled, which causes Linux to crash very early,
shortly after decompressing the kernel.
Using U-Boot allows to circumvent these limitations. We can let the
Samsung bootloader chain-load U-Boot and U-Boot locks the L2 cache
before booting into Linux. U-Boot has several other advantages
- it supports device-trees directly and we are no longer limited to
flashing Android boot images through Samsung's proprietary download
mode.
The Samsung "stemmy" board covers all Samsung devices based on U8500.
Add minimal support for "stemmy". For now only UART is supported but
this will be extended later.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Stephan Gerhold [Sat, 4 Jan 2020 17:45:17 +0000 (18:45 +0100)]
arm: Add support for ST-Ericsson U8500 SoC
The NovaThor U8500 SoC was released by ST-Ericsson in 2011.
It was used for some development boards like the CALAO Systems
Snowball SBC, but mass production was primarily for Android
smartphones like the Samsung Galaxy S III mini.
Previous support for U8500 was removed in
commit 68282f55b846 ("arm: Remove unused ST-Ericsson u8500 arch")
since none of the boards were converted to generic boards
before the deadline.
The new code does not have much in common with the previous code.
I have completely rewritten everything, embracing the Driver Model
and device trees wherever possible.
The U8500 support is a bit more minimal for now - my primary
use case is to use U-Boot as alternative bootloader for some of the
U8500 Samsung smartphones. At the moment U-Boot is chain-loaded from
the original Samsung bootloader. A side effect of this is that we
can (temporarily) get away without implementing some functionality
- e.g. all clocks are already enabled by the original bootloader.
More functionality will be added in future patches.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: John Rigby <john.rigby@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
tried to fix, namely that the reference to env_flags_validate from
env_htab cannot be satisfied when flags.o is not built in. However,
that commit got reverted by
d90fc9c3de Revert "env: solve compilation error in SPL"
Necessary, but not sufficient conditions to see this are
CONFIG_SPL=y (obviously)
CONFIG_SPL_ENV_SUPPORT=n (so flags.o does not get compiled)
CONFIG_SPL_LIBCOMMON_SUPPORT=y (so env/built-in.o is part of the SPL link)
Now, these are satisfied for e.g. imx6q_logic_defconfig. But that
builds just fine, and spl/u-boot-spl.map lists .data.env_htab among
the discarded (garbage collected) sections. Yet, on our
mpc8309-derived board, we do see the build failure, so perhaps the
linker works a bit differently on ppc than on ARM, or there's yet some
other configuration option needed to observe the break.
This is another attempt at solving it, which also cleans up
env/Makefile a bit: Introduce a def_bool y symbol CONFIG_ENV_SUPPORT
which complements CONFIG_(SPL/TPL)_SUPPORT. Then use
CONFIG_$(SPL_TPL_)ENV_SUPPORT to decide whether to include the five
basic env/*.o files. For attr.o, flags.o and callback.o, this
shouldn't change anything. Also, common.o and env.o still get
unconditionally built for U-boot proper. But for TPL/SPL, those two
are only included if CONFIG_(SPL/TPL)_SUPPORT is set.
Having that symbol should also allow simplifying conditionals such as
Baruch Siach [Mon, 20 Jan 2020 12:20:14 +0000 (14:20 +0200)]
ARM: mvebu: clearfog: add Clearfog GTR support
Select the serdes configuration table based on the platform identity
read from EEPROM TLV data. Clearfog GTR needs a slightly different
serdes configuration.
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Baruch Siach [Mon, 20 Jan 2020 12:20:11 +0000 (14:20 +0200)]
ARM: mvebu: clearfog: read basic TLV data
Read RAM die capacity from the EEPROM TLV.
Follow the ONIE standard that defines the Vendor Extension entry type
for vendor specific data. We have no Private Enterprise Number at the
moment as the standard requires. Use the dummy all 0xff value for now.
Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de>
Keep only I2C EEPROM support. Use the generic eeprom driver. Fix
checkpatch issues.
Add support for multiple EEPROM TLV stores on the same system. This is
useful in case of SOM and carrier that both provide ID and hardware
configuration information.
Add option to enable for SPL. This allows selection of RAM configuration
based on EEPROM stored board identification.
Baruch Siach [Mon, 20 Jan 2020 12:20:06 +0000 (14:20 +0200)]
ddr: marvell: a38x: allow board specific clock out setup
DDR clock out might be unrelated to the number of active chip-select.
For example, the board might have two DDR components, but only one
chip-select. The clk_enable mask allows the board to enable DDR clocks
regardless of active chip-selects.
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Alifer Moraes [Tue, 14 Jan 2020 18:54:59 +0000 (15:54 -0300)]
imx8m: clock_imx8mm: Staticize functions
Functions fracpll_configure(), decode_intpll(), decode_fracpll(),
get_root_src_clk() and get_root_clk() are used only in the scope of this
file, so make them static to fix the following sparse warnings:
arch/arm/mach-imx/imx8m/clock_imx8mm.c:50:5: warning: no previous
prototype for ‘fracpll_configure’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:271:5: warning: no previous
prototype for ‘decode_intpll’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:418:5: warning: no previous
prototype for ‘decode_fracpll’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:483:5: warning: no previous
prototype for ‘get_root_src_clk’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:527:5: warning: no previous
prototype for ‘get_root_clk’ [-Wmissing-prototypes]
arm: dts: imx7ulp-evk: remove mux value from pad configuration
The mux mode is embedded in the PAD definition and therefore there is
no need to repeat it in the PAD configuration value (more over since
this information will be masked out when the configuration value is
applied).
On SPL enabled systems, the current s_init code (wdog, clock and ldo
init) is executed twice (by SPL and u-boot). This is not necessary and
might lead to boot issues (ie, starting PMC1 when it is already running).
Fabio Estevam [Fri, 17 Jan 2020 11:58:46 +0000 (08:58 -0300)]
mx7ulp_evk_plugin: Disable CONFIG_NET
Currently the following build warning is seen:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
===================================================
Since the mx7ulp-evk board does not have networking support, explicitly
disable networking.
Fix dtb building warnings:
Warning (cooling_device_property): /thermal-zones/cpu-thermal0/cooling-maps/map0:
Missing property '#cooling-cells' in node /cpus/cpu@0 or bad phandle (referred from cooling-device[0])
Arkadiusz Karas [Thu, 2 Jan 2020 18:31:21 +0000 (19:31 +0100)]
ARM: imx: mx6ull: Add iMX6ULL VisionSOM SoM and EVK
Add iMX6ULL VisionSOM SoM and VisionCB-RT-STD evaluation board support.
The SoM has an iMX6ULL, 512 MiB of DRAM and microSD slot. The carrier
board has Ethernet, USB host port, USB OTG port.
Signed-off-by: Arkadiusz Karas <arkadiusz.karas@somlabs.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
projects / u-boot.git / log