From: Denis 'GNUtoo' Carikli Date: Sat, 30 May 2020 03:24:25 +0000 (+0200) Subject: board: tbs2910: add documentation X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=f3767bcb31d0ce5c6381d5f6c33a951774ee6d41;p=u-boot.git board: tbs2910: add documentation This documents the u-boot installation procedure and the hardware in order to get started. Signed-off-by: Denis 'GNUtoo' Carikli [trini: Add MAINTAINERS entry for doc file per Soeren's request] --- diff --git a/board/tbs/tbs2910/MAINTAINERS b/board/tbs/tbs2910/MAINTAINERS index a3ad2f712a..1e3c0d0ece 100644 --- a/board/tbs/tbs2910/MAINTAINERS +++ b/board/tbs/tbs2910/MAINTAINERS @@ -4,4 +4,5 @@ S: Maintained F: arch/arm/dts/imx6q-tbs2910.dts F: board/tbs/tbs2910/ F: configs/tbs2910_defconfig +F: doc/board/tbs/ F: include/configs/tbs2910.h diff --git a/doc/board/index.rst b/doc/board/index.rst index 01b233f737..bb4473152a 100644 --- a/doc/board/index.rst +++ b/doc/board/index.rst @@ -18,5 +18,6 @@ Board-specific doc rockchip/index sifive/index st/index + tbs/index toradex/index xilinx/index diff --git a/doc/board/tbs/index.rst b/doc/board/tbs/index.rst new file mode 100644 index 0000000000..b677bc624f --- /dev/null +++ b/doc/board/tbs/index.rst @@ -0,0 +1,9 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +TBS +=== + +.. toctree:: + :maxdepth: 2 + + tbs2910 diff --git a/doc/board/tbs/tbs2910.rst b/doc/board/tbs/tbs2910.rst new file mode 100644 index 0000000000..e97f2b6e61 --- /dev/null +++ b/doc/board/tbs/tbs2910.rst @@ -0,0 +1,191 @@ +TBS2910 Matrix ARM miniPC +========================= + +Building +-------- +To build u-boot for the TBS2910 Matrix ARM miniPC, you can use the following +procedure: + +First add the ARM toolchain to your PATH + +Then setup the ARCH and cross compilation environment variables. + +When this is done you can then build u-boot for the TBS2910 Matrix ARM miniPC +with the following commands: + +.. code-block:: none + + make mrproper + make tbs2910_defconfig + make + +Once the build is complete, you can find the resulting image as u-boot.imx in +the current directory. + +UART +---- +The UART voltage is at 3.3V and its settings are 115200bps 8N1 + +BOOT/UPDATE boot switch: +------------------------ +The BOOT/UPDATE switch (SW11) is connected to the BOOT_MODE0 and +BOOT_MODE1 SoC pins. It has "BOOT" and "UPDATE" markings both on +the PCB and on the plastic case. + +When set to the "UPDATE" position, the SoC will use the "Boot From Fuses" +configuration, and since BT_FUSE_SEL is 0, this makes the SOC jump to serial +downloader. + +When set in the "BOOT" position, the SoC will use the "Internal boot" +configuration, and since BT_FUSE_SEL is 0, it will then use the GPIO pins +for the boot configuration. + +SW6 binary DIP switch array on the PCB revision 2.1: +---------------------------------------------------- +On that PCB revision, SW6 has 8 positions. + +Switching a position to ON sets the corresponding +register to 1. + +See the following table for a correspondence between the switch positions and +registers: + +=============== ============ +Switch position Register +=============== ============ +1 BOOT_CFG2[3] +2 BOOT_CFG2[4] +3 BOOT_CFG2[5] +4 BOOT_CFG2[6] +5 BOOT_CFG1[4] +6 BOOT_CFG1[5] +7 BOOT_CFG1[6] +8 BOOT_CFG1[7] +=============== ============ + +For example: + + - To boot from the eMMC: 1:ON , 2:ON, 3:ON, 4:OFF, 5:OFF, 6:ON, 7:ON, 8:OFF + - To boot from the microSD slot: 1: ON, 2: OFF, 3: OFF, 4: OFF, 5:OFF, 6:OFF, + 7:ON, 8:OFF + - To boot from the SD slot: 1: OFF, 2: ON, 3: OFF, 4: OFF, 5:OFF, 6:OFF, 7:ON, + 8:OFF + - To boot from SATA: 1: OFF, 2: OFF, 3: OFF, 4: OFF, 5:OFF, 6:ON, 7:OFF, 8:OFF + +You can refer to the BOOT_CFG registers in the I.MX6Q reference manual for +additional details. + +SW6 binary DIP switch array on the PCB revision 2.3: +---------------------------------------------------- +On that PCB revision, SW6 has only 4 positions. + +Switching a position to ON sets the corresponding +register to 1. + +See the following table for a correspondence between the switch positions and +registers: + +=============== ============ +Switch position Register +=============== ============ +1 BOOT_CFG2[3] +2 BOOT_CFG2[4] +3 BOOT_CFG2[5] +4 BOOT_CFG1[5] +=============== ============ + +For example: + +- To boot from the eMMC: 1:ON, 2:ON, 3:ON, 4:ON +- To boot from the microSD slot: 1:ON, 2:OFF, 3:OFF, 4:OFF +- To boot from the SD slot: 1:OFF, 2:ON, 3:OFF, 4:OFF + +You can refer to the BOOT_CFG registers in the I.MX6Q reference manual for +additional details. + +Loading u-boot from USB: +------------------------ +If you need to load u-boot from USB, you can use the following instructions: + +First build imx_usb_loader, as we will need it to load u-boot from USB. This +can be done with the following commands: + +.. code-block:: none + + git clone git://github.com/boundarydevices/imx_usb_loader.git + cd imx_usb_loader + make + +This will create the resulting imx_usb binary. + +When this is done, you can copy the u-boot.imx image that you built earlier +in in the imx_usb_loader directory. + +You will then need to power off the TBS2910 Matrix ARM miniPC and make sure that +the boot switch is set to "UPDATE" + +Once this is done you can connect an USB cable between the computer that will +run imx_usb and the TBS2910 Matrix ARM miniPC. + +If you also need to access the u-boot console, you will also need to connect an +UART cable between the computer running imx_usb and the TBS2910 Matrix ARM +miniPC. + +Once everything is connected you can finally power on the TBS2910 Matrix ARM +miniPC. The SoC will then jump to the serial download and wait for you. + +Finlay, you can load u-boot through USB with with the following command: + +.. code-block:: none + + sudo ./imx_usb -v u-boot.imx + +The u-boot boot messages will then appear in the serial console. + +Install u-boot on the eMMC: +--------------------------- +To install u-boot on the eMMC, you first need to boot the TBS2910 Matrix ARM +miniPC. + +Once booted, you can flash u-boot.imx to mmcblk0boot0 with the +following commands: + +.. code-block:: none + + sudo echo 0 >/sys/block/mmcblk0boot0/force_ro + sudo dd if=u-boot.imx of=/dev/mmcblk0boot0 bs=1k seek=1; sync + +Note that the eMMC card node may vary, so adjust this as needed. + +Once the new u-boot version is installed, to boot on it you then need to power +off the TBS2910 Matrix ARM miniPC. + +Once it is off, you need make sure that the boot switch is set to "BOOT" and +that the SW6 switch is set to boot on the eMMC as described in the previous +sections. + +If you also need to access the u-boot console, you will also need to connect an +UART cable between the computer running imx_usb and the TBS2910 Matrix ARM +miniPC. + +You can then power up the TBS2910 Matrix ARM miniPC and U-Boot messages will +appear in the serial console. + +Booting a distribution: +----------------------- +When booting on the TBS2910 Matrix ARM miniPC, by default U-Boot will first try +to boot from hardcoded offsets from the start of the eMMC. This is for +compatibility with the stock GNU/Linux distribution. + +If that fails it will then try to boot from several interfaces using +'distro_bootcmd': It will first try to boot from the microSD slot, then the +SD slot, then the internal eMMC, then the SATA interface and finally the USB +interface. For more information on how to configure your distribution to boot, +see 'README.distro'. + +Links: +------ + - https://www.tbsdtv.com/download/document/tbs2910/TBS2910-Matrix-ARM-mini-PC-SCH_rev2.1.pdf + - The schematics for the revision 2.1 of the TBS2910 Matrix ARM miniPC. + - https://cache.freescale.com/files/32bit/doc/ref_manual/IMX6DQRM.pdf - The + SoC reference manual for additional details on the BOOT_CFG registers.