From: Simon Glass Date: Wed, 17 May 2017 14:22:43 +0000 (-0600) Subject: samsung: mmc: Drop s3c_sdi driver X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=ebf925051f13481f9574d52344615c80593442e6;p=u-boot.git samsung: mmc: Drop s3c_sdi driver This is no-longer used in U-Boot. Drop it. Signed-off-by: Simon Glass Reviewed-by: Jaehoon Chung --- diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile index a078649899..2d781c38a6 100644 --- a/drivers/mmc/Makefile +++ b/drivers/mmc/Makefile @@ -40,7 +40,6 @@ obj-$(CONFIG_MMC_MXS) += mxsmmc.o obj-$(CONFIG_MMC_PCI) += pci_mmc.o obj-$(CONFIG_PXA_MMC_GENERIC) += pxa_mmc_gen.o obj-$(CONFIG_SUPPORT_EMMC_RPMB) += rpmb.o -obj-$(CONFIG_S3C_SDI) += s3c_sdi.o obj-$(CONFIG_MMC_SANDBOX) += sandbox_mmc.o obj-$(CONFIG_SH_MMCIF) += sh_mmcif.o obj-$(CONFIG_SH_SDHI) += sh_sdhi.o diff --git a/drivers/mmc/s3c_sdi.c b/drivers/mmc/s3c_sdi.c deleted file mode 100644 index faf7b83a14..0000000000 --- a/drivers/mmc/s3c_sdi.c +++ /dev/null @@ -1,323 +0,0 @@ -/* - * S3C24xx SD/MMC driver - * - * Based on OpenMoko S3C24xx driver by Harald Welte - * - * Copyright (C) 2014 Marek Vasut - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include -#include - -#define S3C2440_SDICON_SDRESET (1 << 8) -#define S3C2410_SDICON_FIFORESET (1 << 1) -#define S3C2410_SDICON_CLOCKTYPE (1 << 0) - -#define S3C2410_SDICMDCON_LONGRSP (1 << 10) -#define S3C2410_SDICMDCON_WAITRSP (1 << 9) -#define S3C2410_SDICMDCON_CMDSTART (1 << 8) -#define S3C2410_SDICMDCON_SENDERHOST (1 << 6) -#define S3C2410_SDICMDCON_INDEX 0x3f - -#define S3C2410_SDICMDSTAT_CRCFAIL (1 << 12) -#define S3C2410_SDICMDSTAT_CMDSENT (1 << 11) -#define S3C2410_SDICMDSTAT_CMDTIMEOUT (1 << 10) -#define S3C2410_SDICMDSTAT_RSPFIN (1 << 9) - -#define S3C2440_SDIDCON_DS_WORD (2 << 22) -#define S3C2410_SDIDCON_TXAFTERRESP (1 << 20) -#define S3C2410_SDIDCON_RXAFTERCMD (1 << 19) -#define S3C2410_SDIDCON_BLOCKMODE (1 << 17) -#define S3C2410_SDIDCON_WIDEBUS (1 << 16) -#define S3C2440_SDIDCON_DATSTART (1 << 14) -#define S3C2410_SDIDCON_XFER_RXSTART (2 << 12) -#define S3C2410_SDIDCON_XFER_TXSTART (3 << 12) -#define S3C2410_SDIDCON_BLKNUM 0x7ff - -#define S3C2410_SDIDSTA_FIFOFAIL (1 << 8) -#define S3C2410_SDIDSTA_CRCFAIL (1 << 7) -#define S3C2410_SDIDSTA_RXCRCFAIL (1 << 6) -#define S3C2410_SDIDSTA_DATATIMEOUT (1 << 5) -#define S3C2410_SDIDSTA_XFERFINISH (1 << 4) - -#define S3C2410_SDIFSTA_TFHALF (1 << 11) -#define S3C2410_SDIFSTA_COUNTMASK 0x7f - -/* - * WARNING: We only support one SD IP block. - * NOTE: It's not likely there will ever exist an S3C24xx with two, - * at least not in this universe all right. - */ -static int wide_bus; - -static int -s3cmmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data) -{ - struct s3c24x0_sdi *sdi_regs = s3c24x0_get_base_sdi(); - uint32_t sdiccon, sdicsta, sdidcon, sdidsta, sdidat, sdifsta; - uint32_t sdicsta_wait_bit = S3C2410_SDICMDSTAT_CMDSENT; - unsigned int timeout = 100000; - int ret = 0, xfer_len, data_offset = 0; - const uint32_t sdidsta_err_mask = S3C2410_SDIDSTA_FIFOFAIL | - S3C2410_SDIDSTA_CRCFAIL | S3C2410_SDIDSTA_RXCRCFAIL | - S3C2410_SDIDSTA_DATATIMEOUT; - - - writel(0xffffffff, &sdi_regs->sdicsta); - writel(0xffffffff, &sdi_regs->sdidsta); - writel(0xffffffff, &sdi_regs->sdifsta); - - /* Set up data transfer (if applicable). */ - if (data) { - writel(data->blocksize, &sdi_regs->sdibsize); - - sdidcon = data->blocks & S3C2410_SDIDCON_BLKNUM; - sdidcon |= S3C2410_SDIDCON_BLOCKMODE; -#if defined(CONFIG_S3C2440) - sdidcon |= S3C2440_SDIDCON_DS_WORD | S3C2440_SDIDCON_DATSTART; -#endif - if (wide_bus) - sdidcon |= S3C2410_SDIDCON_WIDEBUS; - - if (data->flags & MMC_DATA_READ) { - sdidcon |= S3C2410_SDIDCON_RXAFTERCMD; - sdidcon |= S3C2410_SDIDCON_XFER_RXSTART; - } else { - sdidcon |= S3C2410_SDIDCON_TXAFTERRESP; - sdidcon |= S3C2410_SDIDCON_XFER_TXSTART; - } - - writel(sdidcon, &sdi_regs->sdidcon); - } - - /* Write CMD arg. */ - writel(cmd->cmdarg, &sdi_regs->sdicarg); - - /* Write CMD index. */ - sdiccon = cmd->cmdidx & S3C2410_SDICMDCON_INDEX; - sdiccon |= S3C2410_SDICMDCON_SENDERHOST; - sdiccon |= S3C2410_SDICMDCON_CMDSTART; - - /* Command with short response. */ - if (cmd->resp_type & MMC_RSP_PRESENT) { - sdiccon |= S3C2410_SDICMDCON_WAITRSP; - sdicsta_wait_bit = S3C2410_SDICMDSTAT_RSPFIN; - } - - /* Command with long response. */ - if (cmd->resp_type & MMC_RSP_136) - sdiccon |= S3C2410_SDICMDCON_LONGRSP; - - /* Start the command. */ - writel(sdiccon, &sdi_regs->sdiccon); - - /* Wait for the command to complete or for response. */ - for (timeout = 100000; timeout; timeout--) { - sdicsta = readl(&sdi_regs->sdicsta); - if (sdicsta & sdicsta_wait_bit) - break; - - if (sdicsta & S3C2410_SDICMDSTAT_CMDTIMEOUT) - timeout = 1; - } - - /* Clean the status bits. */ - setbits_le32(&sdi_regs->sdicsta, 0xf << 9); - - if (!timeout) { - puts("S3C SDI: Command timed out!\n"); - ret = -ETIMEDOUT; - goto error; - } - - /* Read out the response. */ - if (cmd->resp_type & MMC_RSP_136) { - cmd->response[0] = readl(&sdi_regs->sdirsp0); - cmd->response[1] = readl(&sdi_regs->sdirsp1); - cmd->response[2] = readl(&sdi_regs->sdirsp2); - cmd->response[3] = readl(&sdi_regs->sdirsp3); - } else { - cmd->response[0] = readl(&sdi_regs->sdirsp0); - } - - /* If there are no data, we're done. */ - if (!data) - return 0; - - xfer_len = data->blocksize * data->blocks; - - while (xfer_len > 0) { - sdidsta = readl(&sdi_regs->sdidsta); - sdifsta = readl(&sdi_regs->sdifsta); - - if (sdidsta & sdidsta_err_mask) { - printf("S3C SDI: Data error (sdta=0x%08x)\n", sdidsta); - ret = -EIO; - goto error; - } - - if (data->flags & MMC_DATA_READ) { - if ((sdifsta & S3C2410_SDIFSTA_COUNTMASK) < 4) - continue; - sdidat = readl(&sdi_regs->sdidat); - put_unaligned_le32(sdidat, data->dest + data_offset); - } else { /* Write */ - /* TX FIFO half full. */ - if (!(sdifsta & S3C2410_SDIFSTA_TFHALF)) - continue; - - /* TX FIFO is below 32b full, write. */ - sdidat = get_unaligned_le32(data->src + data_offset); - writel(sdidat, &sdi_regs->sdidat); - } - data_offset += 4; - xfer_len -= 4; - } - - /* Wait for the command to complete or for response. */ - for (timeout = 100000; timeout; timeout--) { - sdidsta = readl(&sdi_regs->sdidsta); - if (sdidsta & S3C2410_SDIDSTA_XFERFINISH) - break; - - if (sdidsta & S3C2410_SDIDSTA_DATATIMEOUT) - timeout = 1; - } - - /* Clear status bits. */ - writel(0x6f8, &sdi_regs->sdidsta); - - if (!timeout) { - puts("S3C SDI: Command timed out!\n"); - ret = -ETIMEDOUT; - goto error; - } - - writel(0, &sdi_regs->sdidcon); - - return 0; -error: - return ret; -} - -static int s3cmmc_set_ios(struct mmc *mmc) -{ - struct s3c24x0_sdi *sdi_regs = s3c24x0_get_base_sdi(); - uint32_t divider = 0; - - wide_bus = (mmc->bus_width == 4); - - if (!mmc->clock) - return 0; - - divider = DIV_ROUND_UP(get_PCLK(), mmc->clock); - if (divider) - divider--; - - writel(divider, &sdi_regs->sdipre); - mdelay(125); - - return 0; -} - -static int s3cmmc_init(struct mmc *mmc) -{ - struct s3c24x0_clock_power *clk_power = s3c24x0_get_base_clock_power(); - struct s3c24x0_sdi *sdi_regs = s3c24x0_get_base_sdi(); - - /* Start the clock. */ - setbits_le32(&clk_power->clkcon, 1 << 9); - -#if defined(CONFIG_S3C2440) - writel(S3C2440_SDICON_SDRESET, &sdi_regs->sdicon); - mdelay(10); - writel(0x7fffff, &sdi_regs->sdidtimer); -#else - writel(0xffff, &sdi_regs->sdidtimer); -#endif - writel(MMC_MAX_BLOCK_LEN, &sdi_regs->sdibsize); - writel(0x0, &sdi_regs->sdiimsk); - - writel(S3C2410_SDICON_FIFORESET | S3C2410_SDICON_CLOCKTYPE, - &sdi_regs->sdicon); - - mdelay(125); - - return 0; -} - -struct s3cmmc_priv { - struct mmc_config cfg; - int (*getcd)(struct mmc *); - int (*getwp)(struct mmc *); -}; - -static int s3cmmc_getcd(struct mmc *mmc) -{ - struct s3cmmc_priv *priv = mmc->priv; - if (priv->getcd) - return priv->getcd(mmc); - else - return 0; -} - -static int s3cmmc_getwp(struct mmc *mmc) -{ - struct s3cmmc_priv *priv = mmc->priv; - if (priv->getwp) - return priv->getwp(mmc); - else - return 0; -} - -static const struct mmc_ops s3cmmc_ops = { - .send_cmd = s3cmmc_send_cmd, - .set_ios = s3cmmc_set_ios, - .init = s3cmmc_init, - .getcd = s3cmmc_getcd, - .getwp = s3cmmc_getwp, -}; - -int s3cmmc_initialize(bd_t *bis, int (*getcd)(struct mmc *), - int (*getwp)(struct mmc *)) -{ - struct s3cmmc_priv *priv; - struct mmc *mmc; - struct mmc_config *cfg; - - priv = calloc(1, sizeof(*priv)); - if (!priv) - return -ENOMEM; - cfg = &priv->cfg; - - cfg->name = "S3C MMC"; - cfg->ops = &s3cmmc_ops; - cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34; - cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_HS; - cfg->f_min = 400000; - cfg->f_max = get_PCLK() / 2; - cfg->b_max = 0x80; - -#if defined(CONFIG_S3C2410) - /* - * S3C2410 has some bug that prevents reliable - * operation at higher speed - */ - cfg->f_max /= 2; -#endif - - mmc = mmc_create(cfg, priv); - if (!mmc) { - free(priv); - return -ENOMEM; - } - - return 0; -} diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index 8554941f4c..0ae397fbb7 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -2299,7 +2299,6 @@ CONFIG_S3C2400 CONFIG_S3C2410 CONFIG_S3C2410_NAND_BBT CONFIG_S3C2410_NAND_HWECC -CONFIG_S3C2440 CONFIG_S3C24X0 CONFIG_S3C24XX_TACLS CONFIG_S3C24XX_TWRPH0