From: Simon Glass <sjg@chromium.org>
Date: Sat, 13 May 2017 03:09:49 +0000 (-0600)
Subject: i2c: Drop use of CONFIG_I2C_HARD
X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=eb5ba3aefdf0f6c;p=u-boot.git

i2c: Drop use of CONFIG_I2C_HARD

This option is pretty old. It predates CONFIG_SYS_I2C which is itself
deprecated in favour of driver model. Disable it for all boards.

Also drop I2C options which depend on this.

Signed-off-by: Simon Glass <sjg@chromium.org>
---

diff --git a/README b/README
index 2ca0102b57..86f0814f79 100644
--- a/README
+++ b/README
@@ -2213,22 +2213,9 @@ The following options need to be configured:
 		- approved multibus support
 		- better i2c mux support
 
-		** Please consider updating your I2C driver now. **
+		** CONFIG_HARD_I2C is now being removed **
 
-		These enable legacy I2C serial bus commands. Defining
-		CONFIG_HARD_I2C will include the appropriate I2C driver
-		for the selected CPU.
-
-		This will allow you to use i2c commands at the u-boot
-		command line (as long as you set CONFIG_CMD_I2C in
-		CONFIG_COMMANDS) and communicate with i2c based realtime
-		clock chips. See common/cmd_i2c.c for a description of the
-		command line interface.
-
-		CONFIG_HARD_I2C selects a hardware I2C controller.
-
-		There are several other quantities that must also be
-		defined when you define CONFIG_HARD_I2C.
+----under removal:
 
 		In both cases you will need to define CONFIG_SYS_I2C_SPEED
 		to be the frequency (in Hz) at which you wish your i2c bus
diff --git a/arch/arm/include/asm/arch-armada100/config.h b/arch/arm/include/asm/arch-armada100/config.h
index 6ebc759f4b..113e1c73f3 100644
--- a/arch/arm/include/asm/arch-armada100/config.h
+++ b/arch/arm/include/asm/arch-armada100/config.h
@@ -24,17 +24,5 @@
 #define MV_UART_CONSOLE_BASE	ARMD1_UART1_BASE
 #define CONFIG_SYS_NS16550_IER	(1 << 6)	/* Bit 6 in UART_IER register
 						represents UART Unit Enable */
-/*
- * I2C definition
- */
-#ifdef CONFIG_CMD_I2C
-#define CONFIG_I2C_MV		1
-#define CONFIG_MV_I2C_NUM	2
-#define CONFIG_I2C_MULTI_BUS	1
-#define CONFIG_MV_I2C_REG	{0xd4011000, 0xd4025000}
-#define CONFIG_HARD_I2C		1
-#define CONFIG_SYS_I2C_SPEED	0
-#define CONFIG_SYS_I2C_SLAVE	0xfe
-#endif
 
 #endif /* _ARMD1_CONFIG_H */
diff --git a/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c b/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c
index 31418a1f96..9205c22e0b 100644
--- a/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c
+++ b/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c
@@ -156,17 +156,7 @@ int board_init(void)
 
 int board_late_init(void)
 {
-	u8 mac[6];
-
-	/* Read Mac Address and set*/
-	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-	i2c_set_bus_num(CONFIG_SYS_I2C_MODULE);
-
-	/* Read MAC address */
-	i2c_read(0x50, 0x0, 0, mac, 6);
-
-	if (is_valid_ethaddr(mac))
-		eth_setenv_enetaddr("ethaddr", mac);
+	printf("Cannot use I2C to get MAC address\n");
 
 	return 0;
 }
diff --git a/board/cm5200/cm5200.c b/board/cm5200/cm5200.c
index 7b862355c8..2f55191caf 100644
--- a/board/cm5200/cm5200.c
+++ b/board/cm5200/cm5200.c
@@ -161,14 +161,7 @@ int dram_init(void)
  */
 static void read_hw_id(hw_id_t hw_id)
 {
-	int i;
-	for (i = 0; i < HW_ID_ELEM_COUNT; ++i)
-		if (i2c_read(CONFIG_SYS_I2C_EEPROM,
-				hw_id_format[i].offset,
-				2,
-				(uchar *)&hw_id[i][0],
-				hw_id_format[i].length) != 0)
-			printf("ERROR: can't read HW ID from EEPROM\n");
+	printf("ERROR: can't read HW ID from EEPROM\n");
 }
 
 
@@ -221,7 +214,7 @@ static void compose_module_name(hw_id_t hw_id, char *buf)
 	strcat(buf, tmp);
 }
 
-
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
 /*
  * Compose string with hostname.
  * buf is assumed to have enough space, and be null-terminated.
@@ -237,7 +230,7 @@ static void compose_hostname(hw_id_t hw_id, char *buf)
 		*p = tolower(*p);
 
 }
-
+#endif
 
 #ifdef CONFIG_OF_BOARD_SETUP
 /*
@@ -270,15 +263,6 @@ int checkboard(void)
 	hw_id_t hw_id_tmp;
 	char module_name_tmp[MODULE_NAME_MAXLEN] = "";
 
-	/*
-	 * We need I2C to access HW ID data from EEPROM, so we call i2c_init()
-	 * here despite the fact that it will be called again later on. We
-	 * also use a little trick to silence I2C-related output.
-	 */
-	gd->flags |= GD_FLG_SILENT;
-	i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-	gd->flags &= ~GD_FLG_SILENT;
-
 	read_hw_id(hw_id_tmp);
 	identify_module(hw_id_tmp);	/* this sets gd->board_type */
 	compose_module_name(hw_id_tmp, module_name_tmp);
@@ -334,16 +318,16 @@ int misc_init_r(void)
 			" device at address %02X:%04X\n", CONFIG_SYS_I2C_EEPROM,
 			CONFIG_MAC_OFFSET);
 	}
+	hostname[0] = 0x00;
+	/* set the hostname appropriate to the module we're running on */
+	compose_hostname(hw_id, hostname);
+	setenv("hostname", hostname);
+
 #endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) */
 	if (!getenv("ethaddr"))
 		printf(LOG_PREFIX "MAC address not set, networking is not "
 					"operational\n");
 
-	/* set the hostname appropriate to the module we're running on */
-	hostname[0] = 0x00;
-	compose_hostname(hw_id, hostname);
-	setenv("hostname", hostname);
-
 	return 0;
 }
 #endif /* CONFIG_MISC_INIT_R */
diff --git a/board/cm5200/cmd_cm5200.c b/board/cm5200/cmd_cm5200.c
index 9c40ad7b2a..60097dc8c7 100644
--- a/board/cm5200/cmd_cm5200.c
+++ b/board/cm5200/cmd_cm5200.c
@@ -13,34 +13,6 @@
 
 #ifdef CONFIG_CMD_BSP
 
-static int do_i2c_test(char * const argv[])
-{
-	unsigned char temp, temp1;
-
-	printf("Starting I2C Test\n"
-		"Please set Jumper:\nI2C SDA 2-3\nI2C SCL 2-3\n\n"
-		"Please press any key to start\n\n");
-	getc();
-
-	temp = 0xf0; /* set io 0-4 as output */
-	i2c_write(CONFIG_SYS_I2C_IO, 3, 1, (uchar *)&temp, 1);
-
-	printf("Press I2C4-7. LED I2C0-3 should have the same state\n\n"
-		"Press any key to stop\n\n");
-
-	while (!tstc()) {
-		i2c_read(CONFIG_SYS_I2C_IO, 0, 1, (uchar *)&temp, 1);
-		temp1 = (temp >> 4) & 0x03;
-		temp1 |= (temp >> 3) & 0x08; /* S302 -> LED303 */
-		temp1 |= (temp >> 5) & 0x04; /* S303 -> LED302 */
-		temp = temp1;
-		i2c_write(CONFIG_SYS_I2C_IO, 1, 1, (uchar *)&temp, 1);
-	}
-	getc();
-
-	return 0;
-}
-
 static int do_usb_test(char * const argv[])
 {
 	int i;
@@ -387,9 +359,7 @@ static int cmd_fkt(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 
 	switch (argc) {
 	case 2:
-		if (strncmp(argv[1], "i2c", 3) == 0)
-			rcode = do_i2c_test(argv);
-		else if (strncmp(argv[1], "led", 3) == 0)
+		if (strncmp(argv[1], "led", 3) == 0)
 			rcode = do_led_test(argv);
 		else if (strncmp(argv[1], "usb", 3) == 0)
 			rcode = do_usb_test(argv);
diff --git a/board/davedenx/aria/aria.c b/board/davedenx/aria/aria.c
index e3441cad4e..e389819e9d 100644
--- a/board/davedenx/aria/aria.c
+++ b/board/davedenx/aria/aria.c
@@ -29,9 +29,6 @@ int misc_init_r(void)
 {
 	u32 tmp;
 
-	/* we use I2C-2 for on-board eeprom */
-	i2c_set_bus_num(2);
-
 	tmp = in_be32((u32*)CONFIG_SYS_ARIA_FPGA_BASE);
 	printf("FPGA:  %u-%u.%u.%u\n",
 		(tmp & 0xFF000000) >> 24,
diff --git a/board/esd/mecp5123/mecp5123.c b/board/esd/mecp5123/mecp5123.c
index 66dc407bae..78a6b66110 100644
--- a/board/esd/mecp5123/mecp5123.c
+++ b/board/esd/mecp5123/mecp5123.c
@@ -18,17 +18,7 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int eeprom_write_enable(unsigned dev_addr, int state)
 {
-	volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
-
-	if (dev_addr != CONFIG_SYS_I2C_EEPROM_ADDR)
-		return -1;
-
-	if (state == 0)
-		setbits_be32(&im->gpio.gpdat, 0x00100000);
-	else
-		clrbits_be32(&im->gpio.gpdat, 0x00100000);
-
-	return 0;
+	return -ENOSYS;
 }
 
 int board_early_init_f(void)
diff --git a/board/freescale/mpc5121ads/mpc5121ads.c b/board/freescale/mpc5121ads/mpc5121ads.c
index f87579f193..d729056fd0 100644
--- a/board/freescale/mpc5121ads/mpc5121ads.c
+++ b/board/freescale/mpc5121ads/mpc5121ads.c
@@ -174,27 +174,6 @@ int dram_init(void)
 
 int misc_init_r(void)
 {
-	u8 tmp_val;
-
-	/* Using this for DIU init before the driver in linux takes over
-	 *  Enable the TFP410 Encoder (I2C address 0x38)
-	 */
-
-	i2c_set_bus_num(2);
-	tmp_val = 0xBF;
-	i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
-	/* Verify if enabled */
-	tmp_val = 0;
-	i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
-	debug("DVI Encoder Read: 0x%02x\n", tmp_val);
-
-	tmp_val = 0x10;
-	i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
-	/* Verify if enabled */
-	tmp_val = 0;
-	i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
-	debug("DVI Encoder Read: 0x%02x\n", tmp_val);
-
 	return 0;
 }
 
diff --git a/board/ifm/ac14xx/ac14xx.c b/board/ifm/ac14xx/ac14xx.c
index 348613736d..cd79e804a0 100644
--- a/board/ifm/ac14xx/ac14xx.c
+++ b/board/ifm/ac14xx/ac14xx.c
@@ -17,7 +17,6 @@
 #include <i2c.h>
 #endif
 
-static int eeprom_diag;
 static int mac_diag;
 static int gpio_diag;
 
@@ -136,7 +135,6 @@ struct __attribute__ ((__packed__)) eeprom_layout {
 #define HW_COMP_MAINCPU 2
 
 static struct eeprom_layout eeprom_content;
-static int eeprom_was_read;	/* has_been_read */
 static int eeprom_is_valid;
 static int eeprom_version;
 
@@ -153,53 +151,7 @@ static int eeprom_version;
 
 static int read_eeprom(void)
 {
-	int eeprom_datalen;
-	int ret;
-
-	if (eeprom_was_read)
-		return 0;
-
-	eeprom_is_valid = 0;
-	ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
-			CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
-			(uchar *)&eeprom_content, sizeof(eeprom_content));
-	if (eeprom_diag) {
-		printf("DIAG: %s() read rc[%d], size[%d]\n",
-			__func__, ret, sizeof(eeprom_content));
-	}
-
-	if (ret != 0)
-		return -1;
-
-	eeprom_was_read = 1;
-
-	/*
-	 * check validity of EEPROM content
-	 * (check version, length, optionally checksum)
-	 */
-	eeprom_is_valid = 1;
-	eeprom_datalen = get_eeprom_field_int(eeprom_content.len);
-	eeprom_version = get_eeprom_field_int(eeprom_content.version);
-
-	if (eeprom_diag) {
-		printf("DIAG: %s() magic[%c%c%c] len[%d] ver[%d] type[%d]\n",
-			__func__, eeprom_content.magic[0],
-			eeprom_content.magic[1], eeprom_content.magic[2],
-			eeprom_datalen, eeprom_version, eeprom_content.type);
-	}
-	if (strncmp(eeprom_content.magic, "ifm", strlen("ifm")) != 0)
-		eeprom_is_valid = 0;
-	if (eeprom_datalen < sizeof(struct eeprom_layout) - 5)
-		eeprom_is_valid = 0;
-	if ((eeprom_version != 1) && (eeprom_version != 2))
-		eeprom_is_valid = 0;
-	if (eeprom_content.type != HW_COMP_MAINCPU)
-		eeprom_is_valid = 0;
-
-	if (eeprom_diag)
-		printf("DIAG: %s() valid[%d]\n", __func__, eeprom_is_valid);
-
-	return ret;
+	return -ENOSYS;
 }
 
 int mac_read_from_eeprom(void)
@@ -324,9 +276,6 @@ int misc_init_r(void)
 	char *s;
 	int want_recovery;
 
-	/* we use bus I2C-0 for the on-board eeprom */
-	i2c_set_bus_num(0);
-
 	/* setup GPIO directions and initial values */
 	gpio_configure();
 
diff --git a/board/renesas/r0p7734/r0p7734.c b/board/renesas/r0p7734/r0p7734.c
index 360e0a1a6f..d0b4537513 100644
--- a/board/renesas/r0p7734/r0p7734.c
+++ b/board/renesas/r0p7734/r0p7734.c
@@ -44,17 +44,7 @@ int board_init(void)
 
 int board_late_init(void)
 {
-	u8 mac[6];
-
-	/* Read Mac Address and set*/
-	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-	i2c_set_bus_num(CONFIG_SYS_I2C_MODULE);
-
-	/* Read MAC address */
-	i2c_read(0x50, 0x10, 0, mac, 6);
-
-	if (is_valid_ethaddr(mac))
-		eth_setenv_enetaddr("ethaddr", mac);
+	printf("Cannot get MAC address from I2C\n");
 
 	return 0;
 }
diff --git a/board/tqc/tqm5200/tqm5200.c b/board/tqc/tqm5200/tqm5200.c
index 92db093dbf..c48ab11fc4 100644
--- a/board/tqc/tqm5200/tqm5200.c
+++ b/board/tqc/tqm5200/tqm5200.c
@@ -486,20 +486,14 @@ int board_early_init_f (void)
 
 static int tfp410_read_reg(int reg, uchar *buf)
 {
-	if (i2c_read(CONFIG_SYS_TFP410_ADDR, reg, 1, buf, 1) != 0) {
-		puts ("Error reading the chip.\n");
-		return 1;
-	}
-	return 0;
+	puts("Error reading the chip.\n");
+	return -ENOSYS;
 }
 
 static int tfp410_write_reg(int reg, uchar buf)
 {
-	if (i2c_write(CONFIG_SYS_TFP410_ADDR, reg, 1, &buf, 1) != 0) {
-		puts ("Error writing the chip.\n");
-		return 1;
-	}
-	return 0;
+	puts("Error writing the chip.\n");
+	return -ENOSYS;
 }
 
 typedef struct _tfp410_config {
@@ -525,12 +519,9 @@ static int charon_last_stage_init(void)
 {
 	volatile struct mpc5xxx_lpb *lpb =
 		(struct mpc5xxx_lpb *) MPC5XXX_LPB;
-	int	oldbus = i2c_get_bus_num();
 	uchar	buf;
 	int	i = 0;
 
-	i2c_set_bus_num(CONFIG_SYS_TFP410_BUS);
-
 	/* check version */
 	if (tfp410_read_reg(TFP410_REG_DEV_ID_H, &buf) != 0)
 		return -1;
@@ -551,7 +542,6 @@ static int charon_last_stage_init(void)
 		i++;
 	}
 	printf("TFP410 initialized.\n");
-	i2c_set_bus_num(oldbus);
 
 	/* set deadcycle for cs3 to 0 */
 	setbits_be32(&lpb->cs_deadcycle, 0xffffcfff);
diff --git a/configs/MiniFAP_defconfig b/configs/MiniFAP_defconfig
index 7d719f81f5..02ca577e28 100644
--- a/configs/MiniFAP_defconfig
+++ b/configs/MiniFAP_defconfig
@@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
@@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
 CONFIG_CMD_SNTP=y
 CONFIG_CMD_BMP=y
 CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_DIAG=y
diff --git a/configs/O2D300_defconfig b/configs/O2D300_defconfig
index 38101f05df..c0e9541b87 100644
--- a/configs/O2D300_defconfig
+++ b/configs/O2D300_defconfig
@@ -4,7 +4,6 @@ CONFIG_TARGET_O2D300=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_BOOTDELAY=5
 CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
diff --git a/configs/O2DNT2_RAMBOOT_defconfig b/configs/O2DNT2_RAMBOOT_defconfig
index 83006e5582..8cff44cf36 100644
--- a/configs/O2DNT2_RAMBOOT_defconfig
+++ b/configs/O2DNT2_RAMBOOT_defconfig
@@ -8,7 +8,6 @@ CONFIG_HUSH_PARSER=y
 CONFIG_AUTOBOOT_KEYED=y
 CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n"
 CONFIG_AUTOBOOT_STOP_STR="++++++++++"
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
diff --git a/configs/O2DNT2_defconfig b/configs/O2DNT2_defconfig
index 4202d85203..f29abb83bc 100644
--- a/configs/O2DNT2_defconfig
+++ b/configs/O2DNT2_defconfig
@@ -7,7 +7,6 @@ CONFIG_HUSH_PARSER=y
 CONFIG_AUTOBOOT_KEYED=y
 CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n"
 CONFIG_AUTOBOOT_STOP_STR="++++++++++"
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
diff --git a/configs/O2D_defconfig b/configs/O2D_defconfig
index b84a1c8839..534cfe12e2 100644
--- a/configs/O2D_defconfig
+++ b/configs/O2D_defconfig
@@ -4,7 +4,6 @@ CONFIG_TARGET_O2D=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_BOOTDELAY=5
 CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
diff --git a/configs/O2I_defconfig b/configs/O2I_defconfig
index efcc769ff4..acf42abe29 100644
--- a/configs/O2I_defconfig
+++ b/configs/O2I_defconfig
@@ -4,7 +4,6 @@ CONFIG_TARGET_O2I=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_BOOTDELAY=5
 CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
diff --git a/configs/O2MNT_O2M110_defconfig b/configs/O2MNT_O2M110_defconfig
index abdc53df21..de647c76b9 100644
--- a/configs/O2MNT_O2M110_defconfig
+++ b/configs/O2MNT_O2M110_defconfig
@@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
 CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M110\""
 CONFIG_BOOTDELAY=5
 CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
diff --git a/configs/O2MNT_O2M112_defconfig b/configs/O2MNT_O2M112_defconfig
index 06089fe3cf..b243e9cc0e 100644
--- a/configs/O2MNT_O2M112_defconfig
+++ b/configs/O2MNT_O2M112_defconfig
@@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
 CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M112\""
 CONFIG_BOOTDELAY=5
 CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
diff --git a/configs/O2MNT_O2M113_defconfig b/configs/O2MNT_O2M113_defconfig
index 1ea3f3a09b..1584058289 100644
--- a/configs/O2MNT_O2M113_defconfig
+++ b/configs/O2MNT_O2M113_defconfig
@@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
 CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M113\""
 CONFIG_BOOTDELAY=5
 CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
diff --git a/configs/O2MNT_defconfig b/configs/O2MNT_defconfig
index 0209085605..20bd31466e 100644
--- a/configs/O2MNT_defconfig
+++ b/configs/O2MNT_defconfig
@@ -4,7 +4,6 @@ CONFIG_TARGET_O2MNT=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_BOOTDELAY=5
 CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
diff --git a/configs/O3DNT_defconfig b/configs/O3DNT_defconfig
index 5ce4140859..ea769e7edc 100644
--- a/configs/O3DNT_defconfig
+++ b/configs/O3DNT_defconfig
@@ -4,7 +4,6 @@ CONFIG_TARGET_O3DNT=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_BOOTDELAY=5
 CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
diff --git a/configs/TQM5200S_HIGHBOOT_defconfig b/configs/TQM5200S_HIGHBOOT_defconfig
index d0cd50a63c..d07596add0 100644
--- a/configs/TQM5200S_HIGHBOOT_defconfig
+++ b/configs/TQM5200S_HIGHBOOT_defconfig
@@ -7,7 +7,6 @@ CONFIG_BOOTDELAY=5
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
@@ -15,7 +14,6 @@ CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_SNTP=y
 CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_DIAG=y
diff --git a/configs/TQM5200S_defconfig b/configs/TQM5200S_defconfig
index 5324a9a11c..af3225554b 100644
--- a/configs/TQM5200S_defconfig
+++ b/configs/TQM5200S_defconfig
@@ -7,7 +7,6 @@ CONFIG_BOOTDELAY=5
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
@@ -15,7 +14,6 @@ CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_SNTP=y
 CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_DIAG=y
diff --git a/configs/TQM5200_B_HIGHBOOT_defconfig b/configs/TQM5200_B_HIGHBOOT_defconfig
index 2f933e6cab..37d6767f28 100644
--- a/configs/TQM5200_B_HIGHBOOT_defconfig
+++ b/configs/TQM5200_B_HIGHBOOT_defconfig
@@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
@@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
 CONFIG_CMD_SNTP=y
 CONFIG_CMD_BMP=y
 CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_DIAG=y
diff --git a/configs/TQM5200_B_defconfig b/configs/TQM5200_B_defconfig
index f204484f59..5e0cf9ea47 100644
--- a/configs/TQM5200_B_defconfig
+++ b/configs/TQM5200_B_defconfig
@@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
@@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
 CONFIG_CMD_SNTP=y
 CONFIG_CMD_BMP=y
 CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_DIAG=y
diff --git a/configs/TQM5200_STK100_defconfig b/configs/TQM5200_STK100_defconfig
index db9bb8a30d..7b4b030d74 100644
--- a/configs/TQM5200_STK100_defconfig
+++ b/configs/TQM5200_STK100_defconfig
@@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
@@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
 CONFIG_CMD_SNTP=y
 CONFIG_CMD_BMP=y
 CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_DIAG=y
diff --git a/configs/TQM5200_defconfig b/configs/TQM5200_defconfig
index eec60f1be4..4792639653 100644
--- a/configs/TQM5200_defconfig
+++ b/configs/TQM5200_defconfig
@@ -9,7 +9,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
@@ -18,7 +17,6 @@ CONFIG_CMD_PING=y
 CONFIG_CMD_SNTP=y
 CONFIG_CMD_BMP=y
 CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_DIAG=y
diff --git a/configs/a4m072_defconfig b/configs/a4m072_defconfig
index ce5edcbf01..0054d4cddb 100644
--- a/configs/a4m072_defconfig
+++ b/configs/a4m072_defconfig
@@ -7,7 +7,6 @@ CONFIG_HUSH_PARSER=y
 CONFIG_AUTOBOOT_KEYED=y
 CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n"
 CONFIG_AUTOBOOT_DELAY_STR="asdfg"
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
diff --git a/configs/ac14xx_defconfig b/configs/ac14xx_defconfig
index e3b7793e04..930ec8acf2 100644
--- a/configs/ac14xx_defconfig
+++ b/configs/ac14xx_defconfig
@@ -5,7 +5,6 @@ CONFIG_FIT=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_SYS_PROMPT="ac14xx> "
 CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
diff --git a/configs/ap_sh4a_4a_defconfig b/configs/ap_sh4a_4a_defconfig
index 75cf53fe21..41c8be9120 100644
--- a/configs/ap_sh4a_4a_defconfig
+++ b/configs/ap_sh4a_4a_defconfig
@@ -13,7 +13,6 @@ CONFIG_VERSION_VARIABLE=y
 # CONFIG_CMD_ENV_EXISTS is not set
 # CONFIG_CMD_LOADB is not set
 # CONFIG_CMD_LOADS is not set
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_FPGA is not set
 # CONFIG_CMD_ECHO is not set
 # CONFIG_CMD_ITEST is not set
diff --git a/configs/apx4devkit_defconfig b/configs/apx4devkit_defconfig
index e2061a2cce..5c30fe3ce7 100644
--- a/configs/apx4devkit_defconfig
+++ b/configs/apx4devkit_defconfig
@@ -14,14 +14,12 @@ CONFIG_HUSH_PARSER=y
 # CONFIG_CMD_IMLS is not set
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_MMC=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_UBI=y
diff --git a/configs/aria_defconfig b/configs/aria_defconfig
index 963661ab2d..0f1432f9a8 100644
--- a/configs/aria_defconfig
+++ b/configs/aria_defconfig
@@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
 CONFIG_BOOTDELAY=5
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
diff --git a/configs/aspenite_defconfig b/configs/aspenite_defconfig
index 26654426ed..0ac39eabd2 100644
--- a/configs/aspenite_defconfig
+++ b/configs/aspenite_defconfig
@@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=3
 CONFIG_BOARD_EARLY_INIT_F=y
 # CONFIG_CMD_IMLS is not set
 # CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 # CONFIG_CMD_NET is not set
 # CONFIG_CMD_NFS is not set
diff --git a/configs/cam5200_defconfig b/configs/cam5200_defconfig
index 92985ab3d6..46a24f56ab 100644
--- a/configs/cam5200_defconfig
+++ b/configs/cam5200_defconfig
@@ -7,14 +7,12 @@ CONFIG_BOOTDELAY=5
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_SNTP=y
 CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
 CONFIG_MAC_PARTITION=y
 CONFIG_DOS_PARTITION=y
 CONFIG_ISO_PARTITION=y
diff --git a/configs/cam5200_niosflash_defconfig b/configs/cam5200_niosflash_defconfig
index 32bc58ee9b..6b9877ff21 100644
--- a/configs/cam5200_niosflash_defconfig
+++ b/configs/cam5200_niosflash_defconfig
@@ -7,14 +7,12 @@ CONFIG_BOOTDELAY=5
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_SNTP=y
 CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
 CONFIG_MAC_PARTITION=y
 CONFIG_DOS_PARTITION=y
 CONFIG_ISO_PARTITION=y
diff --git a/configs/charon_defconfig b/configs/charon_defconfig
index ec22a6368f..8a1429037a 100644
--- a/configs/charon_defconfig
+++ b/configs/charon_defconfig
@@ -9,7 +9,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
diff --git a/configs/cm5200_defconfig b/configs/cm5200_defconfig
index 7d8d01aaaa..d3369f4455 100644
--- a/configs/cm5200_defconfig
+++ b/configs/cm5200_defconfig
@@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=5
 CONFIG_SILENT_CONSOLE=y
 CONFIG_CMD_ASKENV=y
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
diff --git a/configs/digsy_mtc_RAMBOOT_defconfig b/configs/digsy_mtc_RAMBOOT_defconfig
index 0d11eec75a..86b2b0d804 100644
--- a/configs/digsy_mtc_RAMBOOT_defconfig
+++ b/configs/digsy_mtc_RAMBOOT_defconfig
@@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
 CONFIG_AUTOBOOT_DELAY_STR="d"
 CONFIG_AUTOBOOT_STOP_STR=" "
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
@@ -21,7 +20,6 @@ CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_BMP=y
 CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_DIAG=y
diff --git a/configs/digsy_mtc_defconfig b/configs/digsy_mtc_defconfig
index dc17ab4406..85b7f850f7 100644
--- a/configs/digsy_mtc_defconfig
+++ b/configs/digsy_mtc_defconfig
@@ -11,7 +11,6 @@ CONFIG_AUTOBOOT_KEYED=y
 CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n"
 CONFIG_AUTOBOOT_DELAY_STR=" "
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
@@ -19,7 +18,6 @@ CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_BMP=y
 CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_DIAG=y
diff --git a/configs/digsy_mtc_rev5_RAMBOOT_defconfig b/configs/digsy_mtc_rev5_RAMBOOT_defconfig
index 4ab11c755b..7ec8650aca 100644
--- a/configs/digsy_mtc_rev5_RAMBOOT_defconfig
+++ b/configs/digsy_mtc_rev5_RAMBOOT_defconfig
@@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
 CONFIG_AUTOBOOT_DELAY_STR="d"
 CONFIG_AUTOBOOT_STOP_STR=" "
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
@@ -21,7 +20,6 @@ CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_BMP=y
 CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_DIAG=y
diff --git a/configs/digsy_mtc_rev5_defconfig b/configs/digsy_mtc_rev5_defconfig
index 1f3f3c8bb6..b4b8533063 100644
--- a/configs/digsy_mtc_rev5_defconfig
+++ b/configs/digsy_mtc_rev5_defconfig
@@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
 CONFIG_AUTOBOOT_DELAY_STR="d"
 CONFIG_AUTOBOOT_STOP_STR=" "
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
@@ -21,7 +20,6 @@ CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_BMP=y
 CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_DIAG=y
diff --git a/configs/fo300_defconfig b/configs/fo300_defconfig
index b4f334a436..00418153be 100644
--- a/configs/fo300_defconfig
+++ b/configs/fo300_defconfig
@@ -12,7 +12,6 @@ CONFIG_BOARD_EARLY_INIT_F=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
@@ -21,7 +20,6 @@ CONFIG_CMD_PING=y
 CONFIG_CMD_SNTP=y
 CONFIG_CMD_BMP=y
 CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_DIAG=y
diff --git a/configs/gplugd_defconfig b/configs/gplugd_defconfig
index 97bb976803..f44b68dae8 100644
--- a/configs/gplugd_defconfig
+++ b/configs/gplugd_defconfig
@@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=3
 CONFIG_BOARD_EARLY_INIT_F=y
 # CONFIG_CMD_IMLS is not set
 # CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_FPGA is not set
 # CONFIG_CMD_SETEXPR is not set
diff --git a/configs/ipek01_defconfig b/configs/ipek01_defconfig
index cac9326b6c..690bc0f461 100644
--- a/configs/ipek01_defconfig
+++ b/configs/ipek01_defconfig
@@ -7,13 +7,11 @@ CONFIG_BOOTDELAY=5
 # CONFIG_CONSOLE_MUX is not set
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_FAT=y
 # CONFIG_MMC is not set
 CONFIG_MTD_NOR_FLASH=y
diff --git a/configs/m28evk_defconfig b/configs/m28evk_defconfig
index 6acbd77d5f..0ab7f6bb3c 100644
--- a/configs/m28evk_defconfig
+++ b/configs/m28evk_defconfig
@@ -22,7 +22,6 @@ CONFIG_CMD_GREPENV=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_SF=y
 CONFIG_CMD_SPI=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 CONFIG_CMD_GPIO=y
 CONFIG_CMD_DHCP=y
diff --git a/configs/mecp5123_defconfig b/configs/mecp5123_defconfig
index ebf5415464..db52077e1a 100644
--- a/configs/mecp5123_defconfig
+++ b/configs/mecp5123_defconfig
@@ -6,12 +6,10 @@ CONFIG_BOOTDELAY=5
 CONFIG_BOARD_EARLY_INIT_F=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_FAT=y
 # CONFIG_MMC is not set
 CONFIG_MTD_NOR_FLASH=y
diff --git a/configs/motionpro_defconfig b/configs/motionpro_defconfig
index 91384a6259..5040ea5742 100644
--- a/configs/motionpro_defconfig
+++ b/configs/motionpro_defconfig
@@ -8,12 +8,10 @@ CONFIG_AUTOBOOT_KEYED=y
 CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
 CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b"
 CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_BEDBUG=y
 CONFIG_LED_STATUS=y
diff --git a/configs/mpc5121ads_defconfig b/configs/mpc5121ads_defconfig
index c0af8127b5..47c4e5ace7 100644
--- a/configs/mpc5121ads_defconfig
+++ b/configs/mpc5121ads_defconfig
@@ -6,13 +6,11 @@ CONFIG_BOOTDELAY=5
 CONFIG_BOARD_EARLY_INIT_F=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_MAC_PARTITION=y
diff --git a/configs/mpc5121ads_rev2_defconfig b/configs/mpc5121ads_rev2_defconfig
index ad46e02e94..ef700d0773 100644
--- a/configs/mpc5121ads_rev2_defconfig
+++ b/configs/mpc5121ads_rev2_defconfig
@@ -7,13 +7,11 @@ CONFIG_BOOTDELAY=5
 CONFIG_BOARD_EARLY_INIT_F=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_MAC_PARTITION=y
diff --git a/configs/pcm030_LOWBOOT_defconfig b/configs/pcm030_LOWBOOT_defconfig
index d19908ca8f..2933326e5d 100644
--- a/configs/pcm030_LOWBOOT_defconfig
+++ b/configs/pcm030_LOWBOOT_defconfig
@@ -4,11 +4,9 @@ CONFIG_TARGET_PCM030=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF000000"
 CONFIG_BOOTDELAY=3
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
-CONFIG_CMD_DATE=y
 # CONFIG_MMC is not set
 CONFIG_MTD_NOR_FLASH=y
 CONFIG_USB=y
diff --git a/configs/pcm030_defconfig b/configs/pcm030_defconfig
index ef5c85888c..ff9f4e9f4f 100644
--- a/configs/pcm030_defconfig
+++ b/configs/pcm030_defconfig
@@ -4,11 +4,9 @@ CONFIG_TARGET_PCM030=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_BOOTDELAY=3
 CONFIG_SYS_PROMPT="uboot> "
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
-CONFIG_CMD_DATE=y
 # CONFIG_MMC is not set
 CONFIG_MTD_NOR_FLASH=y
 CONFIG_USB=y
diff --git a/configs/pdm360ng_defconfig b/configs/pdm360ng_defconfig
index f45a90caf9..4ef0df1aa8 100644
--- a/configs/pdm360ng_defconfig
+++ b/configs/pdm360ng_defconfig
@@ -10,13 +10,11 @@ CONFIG_SILENT_CONSOLE=y
 # CONFIG_CONSOLE_MUX is not set
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
 # CONFIG_MMC is not set
 CONFIG_MTD_NOR_FLASH=y
 # CONFIG_PCI is not set
diff --git a/configs/r0p7734_defconfig b/configs/r0p7734_defconfig
index c5c3d52718..91b08dc24f 100644
--- a/configs/r0p7734_defconfig
+++ b/configs/r0p7734_defconfig
@@ -13,7 +13,6 @@ CONFIG_VERSION_VARIABLE=y
 # CONFIG_CMD_ENV_EXISTS is not set
 # CONFIG_CMD_LOADB is not set
 # CONFIG_CMD_LOADS is not set
-CONFIG_CMD_I2C=y
 # CONFIG_CMD_FPGA is not set
 # CONFIG_CMD_ECHO is not set
 # CONFIG_CMD_ITEST is not set
diff --git a/configs/v38b_defconfig b/configs/v38b_defconfig
index db4c47c3d2..18dc039d93 100644
--- a/configs/v38b_defconfig
+++ b/configs/v38b_defconfig
@@ -3,13 +3,11 @@ CONFIG_MPC5xxx=y
 CONFIG_TARGET_V38B=y
 CONFIG_BOOTDELAY=3
 CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_DIAG=y
 CONFIG_MAC_PARTITION=y
diff --git a/include/common.h b/include/common.h
index 83e4037a86..45f190a600 100644
--- a/include/common.h
+++ b/include/common.h
@@ -499,9 +499,19 @@ void	reset_phy     (void);
 void	fdc_hw_init   (void);
 
 /* $(BOARD)/eeprom.c */
+#ifdef CONFIG_CMD_EEPROM
 void eeprom_init  (int bus);
 int  eeprom_read  (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
 int  eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
+#else
+/*
+ * Some EEPROM code is depecated because it used the legacy I2C interface. Add
+ * some macros here so we don't have to touch every one of those uses
+ */
+#define eeprom_init(bus)
+#define eeprom_read(dev_addr, offset, buffer, cnt) ((void)-ENOSYS)
+#define eeprom_write(dev_addr, offset, buffer, cnt) ((void)-ENOSYS)
+#endif
 
 /*
  * Set this up regardless of board
diff --git a/include/configs/M54418TWR.h b/include/configs/M54418TWR.h
index 1817571efe..7b162cccef 100644
--- a/include/configs/M54418TWR.h
+++ b/include/configs/M54418TWR.h
@@ -166,7 +166,6 @@
 
 /* I2c */
 #undef CONFIG_SYS_FSL_I2C
-#undef CONFIG_HARD_I2C		/* I2C with hardware support */
 #undef	CONFIG_SYS_I2C_SOFT	/* I2C bit-banged */
 /* I2C speed and slave address  */
 #define CONFIG_SYS_I2C_SPEED		80000
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index 13f4ef67e1..19e0b1be1b 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -124,8 +124,7 @@
 #ifndef CONFIG_CAM5200
 /* POST support */
 #define CONFIG_POST		(CONFIG_SYS_POST_MEMORY   | \
-				 CONFIG_SYS_POST_CPU	   | \
-				 CONFIG_SYS_POST_I2C)
+				 CONFIG_SYS_POST_CPU)
 #endif
 
 #ifdef CONFIG_POST
@@ -144,7 +143,6 @@
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_REGINFO
 
@@ -278,54 +276,6 @@
 #define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2	/* define for 66MHz speed */
 #endif
 
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#ifdef CONFIG_TQM5200_REV100
-#define CONFIG_SYS_I2C_MODULE		1	/* Select I2C module #1 for rev. 100 board */
-#else
-#define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #2 for all other revs */
-#endif
-
-/*
- * I2C clock frequency
- *
- * Please notice, that the resulting clock frequency could differ from the
- * configured value. This is because the I2C clock is derived from system
- * clock over a frequency divider with only a few divider values. U-Boot
- * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
- * approximation allways lies below the configured value, never above.
- */
-#define CONFIG_SYS_I2C_SPEED		100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*
- * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
- * also). For other EEPROMs configuration should be verified. On Mini-FAP the
- * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
- * same configuration could be used.
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5	/* =32 Bytes per write */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	20
-
-/*
- * HW-Monitor configuration on Mini-FAP
- */
-#if defined (CONFIG_MINIFAP)
-#define CONFIG_SYS_I2C_HWMON_ADDR		0x2C
-#endif
-
-/* List of I2C addresses to be verified by POST */
-#if defined (CONFIG_MINIFAP)
-#undef CONFIG_SYS_POST_I2C_ADDRS
-#define CONFIG_SYS_POST_I2C_ADDRS	{CONFIG_SYS_I2C_EEPROM_ADDR,	\
-					 CONFIG_SYS_I2C_HWMON_ADDR,	\
-					 CONFIG_SYS_I2C_SLAVE}
-#endif
-
 /*
  * Flash configuration
  */
@@ -544,18 +494,6 @@
 #endif
 #endif
 
-/*
- * RTC configuration
- */
-#if defined (CONFIG_STK52XX) && !defined (CONFIG_STK52XX_REV100)
-# define CONFIG_RTC_M41T11 1
-# define CONFIG_SYS_I2C_RTC_ADDR 0x68
-# define CONFIG_SYS_M41T11_BASE_YEAR	1900    /* because Linux uses the same base
-					   year */
-#else
-# define CONFIG_RTC_MPC5200	1	/* use internal MPC5200 RTC */
-#endif
-
 /*
  * Miscellaneous configurable options
  */
diff --git a/include/configs/a4m072.h b/include/configs/a4m072.h
index 79099518e7..2ea43ffce1 100644
--- a/include/configs/a4m072.h
+++ b/include/configs/a4m072.h
@@ -81,7 +81,6 @@
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_IDE
 
 #if defined(CONFIG_PCI)
@@ -145,25 +144,6 @@
  */
 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
 
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C			1	/* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED		100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x52	/* 1010010x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
-#define CONFIG_SYS_EEPROM_WREN			1
-#define CONFIG_SYS_EEPROM_WP			GPIO_PSC2_4
-
 /*
  * Flash configuration
  */
diff --git a/include/configs/ac14xx.h b/include/configs/ac14xx.h
index ee015bb83d..2a46e9b864 100644
--- a/include/configs/ac14xx.h
+++ b/include/configs/ac14xx.h
@@ -336,28 +336,11 @@
 
 #define CONFIG_CMDLINE_EDITING		1	/* command line history */
 
-/* I2C */
-#define CONFIG_HARD_I2C			/* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-
-/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
 /*
  * IIM - IC Identification Module
  */
 #undef CONFIG_FSL_IIM
 
-/*
- * EEPROM configuration for Atmel AT24C01:
- * 8-bit addresses, 30ms write delay, 32-Byte Page Write Mode
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x52
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	30
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5
-
 /*
  * Ethernet configuration
  */
@@ -384,7 +367,6 @@
 #define CONFIG_LOADS_ECHO		1
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1
 
-#define CONFIG_CMD_EEPROM
 #undef CONFIG_CMD_FUSE
 #undef CONFIG_CMD_IDE
 #define CONFIG_CMD_JFFS2
diff --git a/include/configs/ap_sh4a_4a.h b/include/configs/ap_sh4a_4a.h
index 5f5882dc8e..d3d72b634d 100644
--- a/include/configs/ap_sh4a_4a.h
+++ b/include/configs/ap_sh4a_4a.h
@@ -35,20 +35,6 @@
 #define CONFIG_BITBANGMII
 #define CONFIG_BITBANGMII_MULTI
 
-/* I2C */
-#define CONFIG_SH_SH7734_I2C	1
-#define CONFIG_HARD_I2C			1
-#define CONFIG_I2C_MULTI_BUS	1
-#define CONFIG_SYS_MAX_I2C_BUS	2
-#define CONFIG_SYS_I2C_MODULE	0
-#define CONFIG_SYS_I2C_SPEED	400000 /* 400 kHz */
-#define CONFIG_SYS_I2C_SLAVE	0x50
-#define CONFIG_SH_I2C_DATA_HIGH	4
-#define CONFIG_SH_I2C_DATA_LOW	5
-#define CONFIG_SH_I2C_CLOCK		500000000
-#define CONFIG_SH_I2C_BASE0		0xFFC70000
-#define CONFIG_SH_I2C_BASE1		0xFFC71000
-
 /* undef to save memory	*/
 #define CONFIG_SYS_LONGHELP
 /* Monitor Command Prompt */
diff --git a/include/configs/apx4devkit.h b/include/configs/apx4devkit.h
index a4c7847dab..cce39f27c7 100644
--- a/include/configs/apx4devkit.h
+++ b/include/configs/apx4devkit.h
@@ -79,12 +79,6 @@
 #define CONFIG_USB_MAX_CONTROLLER_COUNT	1
 #endif
 
-/* RTC */
-#ifdef CONFIG_CMD_DATE
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR		0x51
-#endif
-
 /* Boot Linux */
 #define CONFIG_BOOTFILE			"uImage"
 #define CONFIG_BOOTCOMMAND		"run bootcmd_nand"
diff --git a/include/configs/aria.h b/include/configs/aria.h
index 94f6605d46..4d946fc44a 100644
--- a/include/configs/aria.h
+++ b/include/configs/aria.h
@@ -340,31 +340,11 @@
 
 #endif
 
-/* I2C */
-#define CONFIG_HARD_I2C			/* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-
-/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-#if 0
-#define CONFIG_SYS_I2C_NOPROBES	{{0,0x69}}	/* Don't probe these addrs */
-#endif
-
 /*
  * IIM - IC Identification Module
  */
 #undef CONFIG_FSL_IIM
 
-/*
- * EEPROM configuration for Atmel AT24C32A-10TQ-2.7:
- * 16-bit addresses, 10ms write delay, 32-Byte Page Write Mode
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5
-
 /*
  * Ethernet configuration
  */
@@ -392,7 +372,6 @@
 #define CONFIG_LOADS_ECHO		1
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1
 
-#define CONFIG_CMD_EEPROM
 #undef CONFIG_CMD_FUSE
 #undef CONFIG_CMD_IDE
 #define CONFIG_CMD_JFFS2
diff --git a/include/configs/axs10x.h b/include/configs/axs10x.h
index 768e8fbfa4..66e8cd5e9a 100644
--- a/include/configs/axs10x.h
+++ b/include/configs/axs10x.h
@@ -100,7 +100,7 @@
 /*
  * Environment settings
  */
-#define CONFIG_ENV_IS_IN_EEPROM
+#define CONFIG_ENV_IS_NOWHERE
 #define CONFIG_ENV_SIZE			SZ_512
 #define CONFIG_ENV_OFFSET		0
 
diff --git a/include/configs/cm5200.h b/include/configs/cm5200.h
index 0073cb5373..3a7d826837 100644
--- a/include/configs/cm5200.h
+++ b/include/configs/cm5200.h
@@ -44,7 +44,7 @@
 /*
  * POST support
  */
-#define CONFIG_POST		(CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C)
+#define CONFIG_POST		(CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU)
 #define MPC5XXX_SRAM_POST_SIZE	(MPC5XXX_SRAM_SIZE - 4)
 /* List of I2C addresses to be verified by POST */
 #define CONFIG_SYS_POST_I2C_ADDRS	{CONFIG_SYS_I2C_SLAVE,	\
@@ -199,16 +199,6 @@
 					"2m(kernel),27904k(rootfs),"	\
 					"-(config)"
 
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #2 */
-#define CONFIG_SYS_I2C_SPEED		40000	/* 40 kHz */
-#define CONFIG_SYS_I2C_SLAVE		0x0
-#define CONFIG_SYS_I2C_IO		0x38	/* PCA9554AD I2C I/O port address */
-#define CONFIG_SYS_I2C_EEPROM		0x53	/* I2C EEPROM device address */
-
 /*
  * RTC configuration
  */
diff --git a/include/configs/digsy_mtc.h b/include/configs/digsy_mtc.h
index 2b56945dd9..ab546c50cd 100644
--- a/include/configs/digsy_mtc.h
+++ b/include/configs/digsy_mtc.h
@@ -85,7 +85,6 @@
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_IDE
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_PCI
@@ -205,36 +204,6 @@
 
 #define CONFIG_BOOTCOMMAND	"run mtcb_start"
 
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C		1
-#define CONFIG_SYS_I2C_MODULE	1
-#define CONFIG_SYS_I2C_SPEED	100000
-#define CONFIG_SYS_I2C_SLAVE	0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 	1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	70
-
-/*
- * RTC configuration
- */
-#if defined(CONFIG_DIGSY_REV5)
-#define CONFIG_SYS_I2C_RTC_ADDR	0x56
-#define CONFIG_RTC_RV3029
-/* Enable 5k Ohm trickle charge resistor */
-#define CONFIG_SYS_RV3029_TCR	0x20
-#else
-#define CONFIG_RTC_DS1337
-#define CONFIG_SYS_I2C_RTC_ADDR	0x68
-#define CONFIG_SYS_DS1339_TCR_VAL	0xAB	/* diode + 4k resistor */
-#endif
-
 /*
  * Flash configuration
  */
diff --git a/include/configs/ids8313.h b/include/configs/ids8313.h
index 6b6bbbd5c0..7ffc9d1dd9 100644
--- a/include/configs/ids8313.h
+++ b/include/configs/ids8313.h
@@ -165,7 +165,6 @@
 #define CONFIG_TSEC2
 #define CONFIG_TSEC_ENET
 #define CONFIG_HARD_SPI
-#define CONFIG_HARD_I2C
 
 /*
  * NOR FLASH setup
diff --git a/include/configs/ipek01.h b/include/configs/ipek01.h
index aff4adf5d0..ece72c6aa1 100644
--- a/include/configs/ipek01.h
+++ b/include/configs/ipek01.h
@@ -150,29 +150,6 @@
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
 
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE	2	/* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED	100000	/* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE	0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x53
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR		0x51
-
 #define CONFIG_SYS_FLASH_BASE		0xFC000000
 #define CONFIG_SYS_FLASH_SIZE		0x01000000
 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + \
diff --git a/include/configs/jupiter.h b/include/configs/jupiter.h
index 0d97317c7f..4461623118 100644
--- a/include/configs/jupiter.h
+++ b/include/configs/jupiter.h
@@ -127,25 +127,6 @@
 #define OF_STDOUT_PATH		"/soc5200@f0000000/serial@2000"
 #endif
 
-#if 0
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED		100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	70
-#endif
-
 /*
  * Flash configuration
  */
diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h
index f6fa599e6b..c4717238bb 100644
--- a/include/configs/m28evk.h
+++ b/include/configs/m28evk.h
@@ -16,7 +16,6 @@
 /* U-Boot Commands */
 #define CONFIG_FAT_WRITE
 
-#define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_NAND_TRIMFFS
 
@@ -63,11 +62,6 @@
 #define CONFIG_FEC_MXC
 #endif
 
-/* EEPROM */
-#ifdef CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2
-#endif
-
 /* RTC */
 #ifdef CONFIG_CMD_DATE
 /* Use the internal RTC in the MXS chip */
diff --git a/include/configs/manroland/mpc5200-common.h b/include/configs/manroland/mpc5200-common.h
new file mode 100644
index 0000000000..68874dc029
--- /dev/null
+++ b/include/configs/manroland/mpc5200-common.h
@@ -0,0 +1,176 @@
+/*
+ * (C) Copyright 2009
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __MANROLAND_MPC52XX__COMMON_H
+#define __MANROLAND_MPC52XX__COMMON_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MPC5200		1	/* MPC5200 CPU */
+
+/* ... running at 33.000000MHz	*/
+#define CONFIG_SYS_MPC5XXX_CLKIN	33000000
+
+#define CONFIG_HIGH_BATS	1	/* High BATs supported		*/
+
+/*
+ * Serial console configuration
+ */
+#define CONFIG_PSC_CONSOLE	1	/* console is on PSC1	*/
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200,\
+					 230400 }
+
+#if (CONFIG_SYS_TEXT_BASE == 0xFFF00000) /* Boot low */
+#   define CONFIG_SYS_LOWBOOT		1
+#endif
+
+/*
+ * IPB Bus clocking configuration.
+ */
+#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
+
+/*
+ * Flash configuration
+ */
+#define CONFIG_SYS_FLASH_BASE		0xFF800000
+
+#define CONFIG_SYS_FLASH_SIZE		0x00800000 /* 8 MByte */
+
+#define CONFIG_ENV_ADDR	(CONFIG_SYS_TEXT_BASE+0x40000) /* second sector */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of flash banks
+					   (= chip selects) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout [ms]*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout [ms]*/
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET
+
+/*
+ * Environment settings
+ */
+#define CONFIG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_SIZE		0x4000
+#define CONFIG_ENV_OFFSET_REDUND   (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND     (CONFIG_ENV_SIZE)
+
+/*
+ * Memory map
+ */
+#define CONFIG_SYS_MBAR		0xF0000000
+#define CONFIG_SYS_DEFAULT_MBAR	0x80000000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE -\
+					 GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_SRAM_BASE	0x80100000	/* CS 1 */
+#define CONFIG_SYS_DISPLAY_BASE	0x80600000	/* CS 3 */
+
+/* Settings for XLB = 132 MHz */
+#define SDRAM_DDR	 1
+#define SDRAM_MODE      0x018D0000
+#define SDRAM_EMODE     0x40090000
+#define SDRAM_CONTROL   0x714f0f00
+#define SDRAM_CONFIG1   0x73722930
+#define SDRAM_CONFIG2   0x47770000
+#define SDRAM_TAPDELAY  0x10000000
+
+/* Use ON-Chip SRAM until RAM will be available */
+#define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
+#ifdef CONFIG_POST
+/* preserve space for the post_word at end of on-chip SRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_POST_SIZE
+#else
+#define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#   define CONFIG_SYS_RAMBOOT		1
+#endif
+
+#define CONFIG_SYS_MONITOR_LEN		(192 << 10)
+#define CONFIG_SYS_MALLOC_LEN		(512 << 10)
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
+
+/*
+ * Ethernet configuration
+ */
+#define CONFIG_MPC5xxx_FEC	1
+#define CONFIG_MPC5xxx_FEC_MII100
+#define CONFIG_PHY_ADDR		0x00
+#define CONFIG_MII		1
+
+/*use  Hardware WDT */
+#define CONFIG_HW_WATCHDOG
+
+#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs	*/
+#if defined(CONFIG_CMD_KGDB)
+#  define CONFIG_SYS_CACHELINE_SHIFT	5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Various low-level settings
+ */
+#define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL		HID0_ICE
+
+#define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
+#define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE
+
+/* 8Mbit SRAM @0x80100000 */
+#define CONFIG_SYS_CS1_START		CONFIG_SYS_SRAM_BASE
+
+#define CONFIG_SYS_CS_BURST		0x00000000
+#define CONFIG_SYS_CS_DEADCYCLE	0x33333333
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff Supports IDE harddisk
+ *-----------------------------------------------------------------------
+ */
+
+#undef  CONFIG_IDE_8xx_PCCARD		/* Use IDE with PC Card	Adapter	*/
+
+#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
+#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
+
+#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus	*/
+
+#define CONFIG_IDE_PREINIT	1
+
+#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
+
+#define CONFIG_SYS_ATA_BASE_ADDR	MPC5XXX_ATA
+
+/* Offset for data I/O			*/
+#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0060)
+
+/* Offset for normal register accesses	*/
+#define CONFIG_SYS_ATA_REG_OFFSET	(CONFIG_SYS_ATA_DATA_OFFSET)
+
+/* Offset for alternate registers	*/
+#define CONFIG_SYS_ATA_ALT_OFFSET	(0x005C)
+
+/* Interval between registers	*/
+#define CONFIG_SYS_ATA_STRIDE          4
+
+#define CONFIG_ATAPI            1
+
+#define OF_CPU			"PowerPC,5200@0"
+#define OF_SOC			"soc5200@f0000000"
+#define OF_TBCLK		(bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH		"/soc5200@f0000000/serial@2000"
+#define CONFIG_OF_IDE_FIXUP
+
+#endif /* __MANROLAND_MPC52XX__COMMON_H */
diff --git a/include/configs/mecp5123.h b/include/configs/mecp5123.h
index 1a9cb675df..fe94e663c5 100644
--- a/include/configs/mecp5123.h
+++ b/include/configs/mecp5123.h
@@ -241,26 +241,11 @@
 
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 
-/* I2C */
-#define CONFIG_HARD_I2C			/* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE		0x7F	/* slave address */
-
 /*
  * IIM - IC Identification Module
  */
 #undef CONFIG_FSL_IIM
 
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2	/* 16-bit EEPROM address */
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* Atmel: AT24C32A-10TQ-2.7 */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10	/* 10ms of delay */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5	/* 32-Byte Page Write Mode */
-#define CONFIG_SYS_EEPROM_WREN			/* Use EEPROM write protect */
-
 /*
  * Ethernet configuration
  */
@@ -280,7 +265,7 @@
 /*
  * Environment
  */
-#define CONFIG_ENV_IS_IN_EEPROM		/* Store env in I2C EEPROM	*/
+#define CONFIG_ENV_IS_NOWHERE		/* Store env in I2C EEPROM	*/
 #define CONFIG_ENV_SIZE		0x1000
 #define CONFIG_ENV_OFFSET       0x0000	/* environment starts here	*/
 
@@ -288,7 +273,6 @@
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change	*/
 
 #define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_EEPROM
 #undef CONFIG_CMD_FUSE
 #undef CONFIG_CMD_IDE
 #define CONFIG_CMD_JFFS2
diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h
index 136db0dd26..cb5c346807 100644
--- a/include/configs/motionpro.h
+++ b/include/configs/motionpro.h
@@ -34,7 +34,6 @@
  * Command line configuration.
  */
 #define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_IDE
 #define CONFIG_CMD_IMMAP
 #define CONFIG_CMD_JFFS2
@@ -255,21 +254,6 @@
 #define CONFIG_SYS_ATA_REG_OFFSET	CONFIG_SYS_ATA_DATA_OFFSET
 #define CONFIG_SYS_ATA_STRIDE		4
 
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE		2	/* select I2C module #2 */
-#define CONFIG_SYS_I2C_SPEED		100000	/* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	1	/* 2 bytes per write cycle */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5	/* 2ms/cycle + 3ms extra */
-
 /*
  * RTC configuration
  */
@@ -283,12 +267,6 @@
 #define ENABLE_GPIO_OUT		0x00000024
 #define LED_ON			0x00000010
 
-/*
- * Temperature sensor
- */
-#define CONFIG_DTT_LM75		1
-#define CONFIG_DTT_SENSORS	{ 0x49 }
-
 /*
  * Environment settings
  */
diff --git a/include/configs/mpc5121ads.h b/include/configs/mpc5121ads.h
index dafb724e3f..f3961a6f35 100644
--- a/include/configs/mpc5121ads.h
+++ b/include/configs/mpc5121ads.h
@@ -327,28 +327,11 @@
 
 #endif
 
-/* I2C */
-#define CONFIG_HARD_I2C			/* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-#if 0
-#define CONFIG_SYS_I2C_NOPROBES	{{0,0x69}}	/* Don't probe these addrs */
-#endif
-
 /*
  * IIM - IC Identification Module
  */
 #undef CONFIG_FSL_IIM
 
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2	/* 16-bit EEPROM address */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* Atmel: AT24C32A-10TQ-2.7 */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* 10ms of delay */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5	/* 32-Byte Page Write Mode */
-
 /*
  * Ethernet configuration
  */
@@ -396,7 +379,6 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
-#define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_IDE
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_REGINFO
diff --git a/include/configs/mxs.h b/include/configs/mxs.h
index fdf596f82f..c403dda483 100644
--- a/include/configs/mxs.h
+++ b/include/configs/mxs.h
@@ -126,16 +126,6 @@
 #endif
 #endif
 
-/* I2C */
-#ifdef CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXS
-#define CONFIG_HARD_I2C
-#ifndef CONFIG_SYS_I2C_SPEED
-#define CONFIG_SYS_I2C_SPEED		400000
-#endif
-#endif
-
 /* LCD */
 #ifdef CONFIG_VIDEO
 #define CONFIG_VIDEO_MXS
diff --git a/include/configs/o2dnt-common.h b/include/configs/o2dnt-common.h
index e2881a7177..1b4200bcbf 100644
--- a/include/configs/o2dnt-common.h
+++ b/include/configs/o2dnt-common.h
@@ -68,7 +68,6 @@
 /*
  * Supported commands
  */
-#define CONFIG_CMD_EEPROM
 #ifdef CONFIG_PCI
 #define CONFIG_CMD_PCI
 #endif
@@ -172,27 +171,6 @@
 #define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2	/* define for 66MHz speed */
 #endif
 
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C			1	/* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE		1	/* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED		100000	/* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*
- * EEPROM configuration:
- *
- * O2DNT board is equiped with Ramtron FRAM device FM24CL16
- * 16 Kib Ferroelectric Nonvolatile serial RAM memory
- * organized as 2048 x 8 bits and addressable as eight I2C devices
- * 0x50 ... 0x57 each 256 bytes in size
- *
- */
-#define CONFIG_SYS_I2C_FRAM
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
 /*
  * There is no write delay with FRAM, write operations are performed at bus
  * speed. Thus, no status polling or write delay is needed.
diff --git a/include/configs/pcm030.h b/include/configs/pcm030.h
index 6d8a2338a2..406f3e547a 100644
--- a/include/configs/pcm030.h
+++ b/include/configs/pcm030.h
@@ -49,7 +49,6 @@ Serial console configuration
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_PCI
 
@@ -120,31 +119,6 @@ IPB Bus clocking configuration.
 #define CONFIG_PCI_IO_SIZE		0x01000000
 #define CONFIG_SYS_XLB_PIPELINING	1
 
-/*---------------------------------------------------------------------------
- I2C configuration
----------------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*---------------------------------------------------------------------------
- EEPROM CAT24WC32 configuration
----------------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x52	/* 1010100x */
-#define CONFIG_SYS_I2C_FACT_ADDR	0x52	/* EEPROM CAT24WC32 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2	/* Bytes of address */
-#define CONFIG_SYS_EEPROM_SIZE		2048
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15
-
-/*---------------------------------------------------------------------------
-RTC configuration
----------------------------------------------------------------------------*/
-#define RTC
-#define CONFIG_RTC_PCF8563		1
-#define CONFIG_SYS_I2C_RTC_ADDR		0x51
-
 /*---------------------------------------------------------------------------
  Flash configuration
 ---------------------------------------------------------------------------*/
@@ -172,11 +146,10 @@ RTC configuration
  Environment settings
 ---------------------------------------------------------------------------*/
 
-/* pcm030 ships with environment is EEPROM by default */
-#define CONFIG_ENV_IS_IN_EEPROM	1
+#define CONFIG_ENV_IS_NOWHERE
 #define CONFIG_ENV_OFFSET	0x00	/* environment starts at the */
 					/*beginning of the EEPROM */
-#define CONFIG_ENV_SIZE		CONFIG_SYS_EEPROM_SIZE
+#define CONFIG_ENV_SIZE		2048
 
 #define CONFIG_ENV_OVERWRITE	1
 
diff --git a/include/configs/pdm360ng.h b/include/configs/pdm360ng.h
index 501611dde7..4bd8236b33 100644
--- a/include/configs/pdm360ng.h
+++ b/include/configs/pdm360ng.h
@@ -301,34 +301,11 @@
 #define CONFIG_SYS_PDM360NG_COPROC_READ_DELAY	5000
 #define CONFIG_SYS_PDM360NG_COPROC_BAUDRATE	38400
 
-/*
- * I2C
- */
-#define CONFIG_HARD_I2C			/* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
 /*
  * IIM - IC Identification Module
  */
 #undef CONFIG_FSL_IIM
 
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2	/* 16-bit EEPROM addr */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* ST AT24C01 */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* 10ms of delay */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4	/* 16-Byte Write Mode */
-
-/*
- * MAC addr in EEPROM
- */
-#define CONFIG_SYS_I2C_EEPROM_BUS_NUM		0
-#define CONFIG_SYS_I2C_EEPROM_MAC_OFFSET	0x10
 /*
  * Enabled only to delete "ethaddr" before testing
  * "ethaddr" setting from EEPROM
@@ -344,12 +321,6 @@
 #define CONFIG_FEC_AN_TIMEOUT	1
 #define CONFIG_HAS_ETH0
 
-/*
- * Configure on-board RTC
- */
-#define CONFIG_RTC_M41T62			/* use M41T00 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR		0x68	/* at address 0x68	*/
-
 /*
  * Environment
  */
@@ -367,7 +338,6 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
-#define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_REGINFO
 
 #undef CONFIG_CMD_FUSE
diff --git a/include/configs/r0p7734.h b/include/configs/r0p7734.h
index 642572fc95..b159b1ed8d 100644
--- a/include/configs/r0p7734.h
+++ b/include/configs/r0p7734.h
@@ -40,20 +40,6 @@
 # define CONFIG_SMC911X_BASE (0x84000000)
 #endif
 
-/* I2C */
-#define CONFIG_SH_SH7734_I2C	1
-#define CONFIG_HARD_I2C			1
-#define CONFIG_I2C_MULTI_BUS	1
-#define CONFIG_SYS_MAX_I2C_BUS	2
-#define CONFIG_SYS_I2C_MODULE	0
-#define CONFIG_SYS_I2C_SPEED	100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE	0x50
-#define CONFIG_SH_I2C_DATA_HIGH	4
-#define CONFIG_SH_I2C_DATA_LOW	5
-#define CONFIG_SH_I2C_CLOCK		500000000
-#define CONFIG_SH_I2C_BASE0		0xFFC70000
-#define CONFIG_SH_I2C_BASE1		0xFFC7100
-
 /* undef to save memory	*/
 #define CONFIG_SYS_LONGHELP
 /* Monitor Command Prompt */
diff --git a/include/configs/s32v234evb.h b/include/configs/s32v234evb.h
index 398b3aa343..33487cd86f 100644
--- a/include/configs/s32v234evb.h
+++ b/include/configs/s32v234evb.h
@@ -97,16 +97,6 @@
 #define CONFIG_PHY_MICREL
 #endif
 
-#if 0				/* Disable until the I2C driver will be updated */
-
-/* I2C Configs */
-#define CONFIG_CMD_I2C
-#define CONFIG_HARD_I2C
-#define CONFIG_I2C_MXC
-#define CONFIG_SYS_I2C_BASE		I2C0_BASE_ADDR
-#define CONFIG_SYS_I2C_SPEED		100000
-#endif
-
 #if 0				/* Disable until the FLASH will be implemented */
 #define CONFIG_SYS_USE_NAND
 #endif
diff --git a/include/configs/v38b.h b/include/configs/v38b.h
index cc0007827d..0bc0ae517a 100644
--- a/include/configs/v38b.h
+++ b/include/configs/v38b.h
@@ -134,27 +134,6 @@
  */
 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK			/* define for 133MHz speed */
 
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED		100000	/* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	70
-
-/*
- * RTC configuration
- */
-#define CONFIG_SYS_I2C_RTC_ADDR		0x51
-
 /*
  * Flash configuration - use CFI driver
  */