From: Frieder Schrempf Date: Wed, 29 Sep 2021 14:42:41 +0000 (+0200) Subject: imx: imx6ul: Add support for Kontron Electronics SL/BL i.MX6UL/ULL boards (N63xx... X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=e6f48aad153ae901ca3340b3207968e2f9c47f66;p=u-boot.git imx: imx6ul: Add support for Kontron Electronics SL/BL i.MX6UL/ULL boards (N63xx/N64xx) This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by Kontron Electronics GmbH. Currently there are the following SoM flavors (SoM-Line): * N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND * N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND * N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND And the according evaluation boards (Board-Line): * N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ... * N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ... * N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ... Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config options at compile-time. Though the differences are so minor, that for the scope of these SoMs we just use a single defconfig that is compatible with both SoCs. Signed-off-by: Frieder Schrempf Reviewed-by: Stefano Babic --- diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 45740a48e0..a0b95d75e9 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -815,7 +815,9 @@ dtb-$(CONFIG_MX6UL) += \ imx6ul-liteboard.dtb \ imx6ul-phytec-segin-ff-rdk-nand.dtb \ imx6ul-pico-hobbit.dtb \ - imx6ul-pico-pi.dtb + imx6ul-pico-pi.dtb \ + imx6ul-kontron-n631x-s.dtb \ + imx6ull-kontron-n641x-s.dtb dtb-$(CONFIG_MX6ULL) += \ imx6ull-14x14-evk.dtb \ diff --git a/arch/arm/dts/imx6ul-kontron-n631x-s-u-boot.dtsi b/arch/arm/dts/imx6ul-kontron-n631x-s-u-boot.dtsi new file mode 100644 index 0000000000..d3f013c58c --- /dev/null +++ b/arch/arm/dts/imx6ul-kontron-n631x-s-u-boot.dtsi @@ -0,0 +1,7 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + */ + +#include "imx6ul-kontron-n6x1x-s-u-boot.dtsi" diff --git a/arch/arm/dts/imx6ul-kontron-n631x-s.dts b/arch/arm/dts/imx6ul-kontron-n631x-s.dts new file mode 100644 index 0000000000..407d2b1dab --- /dev/null +++ b/arch/arm/dts/imx6ul-kontron-n631x-s.dts @@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + * Copyright (c) 2019 Krzysztof Kozlowski + */ + +/dts-v1/; + +#include "imx6ul-kontron-n631x-som.dtsi" +#include "imx6ul-kontron-n6x1x-s.dtsi" + +/ { + model = "Kontron N631X S"; + compatible = "kontron,imx6ul-n631x-s", "kontron,imx6ul-n631x-som", + "fsl,imx6ul"; +}; diff --git a/arch/arm/dts/imx6ul-kontron-n631x-som.dtsi b/arch/arm/dts/imx6ul-kontron-n631x-som.dtsi new file mode 100644 index 0000000000..9a1179814b --- /dev/null +++ b/arch/arm/dts/imx6ul-kontron-n631x-som.dtsi @@ -0,0 +1,14 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + * Copyright (c) 2019 Krzysztof Kozlowski + */ + +#include "imx6ul.dtsi" +#include "imx6ul-kontron-n6x1x-som-common.dtsi" + +/ { + model = "Kontron N631X SOM"; + compatible = "kontron,imx6ul-n631x-som", "fsl,imx6ul"; +}; diff --git a/arch/arm/dts/imx6ul-kontron-n6x1x-s-u-boot.dtsi b/arch/arm/dts/imx6ul-kontron-n6x1x-s-u-boot.dtsi new file mode 100644 index 0000000000..39cc6d05d3 --- /dev/null +++ b/arch/arm/dts/imx6ul-kontron-n6x1x-s-u-boot.dtsi @@ -0,0 +1,63 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + */ + +#if defined(CONFIG_FIT) + +/ { + binman: binman { + filename = "flash.bin"; + pad-byte = <0x00>; + + spl: blob-ext@1 { + offset = <0x0>; + filename = "SPL"; + }; + + uboot: blob-ext@2 { + offset = <0x11000>; + filename = "u-boot.img"; + }; + }; +}; + +#endif /* CONFIG_FIT */ + +/* + * To make the PHYs work, we need to set the reset pin once. Afterwards + * in Linux we can't assign the shared reset GPIO to the PHYs, as this + * would cause Linux to reset both PHYs every time one of them gets + * reinitialized. + * + * Also we disable the second ethernet as it currently doesn't work with + * the devicetree setup in U-Boot. + */ + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>; + phy-mode = "rmii"; + phy-handle = <ðphy1>; + phy-reset-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + reg = <1>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET_REF>; + clock-names = "rmii-ref"; + }; + }; +}; + +&fec2 { + status = "disabled"; + /delete-property/ phy-handle; + /delete-node/ mdio; +}; diff --git a/arch/arm/dts/imx6ul-kontron-n6x1x-s.dts b/arch/arm/dts/imx6ul-kontron-n6x1x-s.dts new file mode 100644 index 0000000000..84d8a717ab --- /dev/null +++ b/arch/arm/dts/imx6ul-kontron-n6x1x-s.dts @@ -0,0 +1,423 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + * Copyright (c) 2019 Krzysztof Kozlowski + */ + +/dts-v1/; + +#include +#include "imx6ul-kontron-n6x1x-som.dtsi" + +/ { + gpio-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + led1 { + label = "debug-led1"; + gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; + default-state = "off"; + linux,default-trigger = "heartbeat"; + }; + + led2 { + label = "debug-led2"; + gpios = <&gpio5 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led3 { + label = "debug-led3"; + gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + pwm-beeper { + compatible = "pwm-beeper"; + pwms = <&pwm8 0 5000>; + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_5v: regulator-5v { + compatible = "regulator-fixed"; + regulator-name = "5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_usb_otg1_vbus: regulator-usb-otg1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_vref_adc: regulator-vref-adc { + compatible = "regulator-fixed"; + regulator-name = "vref-adc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&adc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc1>; + num-channels = <3>; + vref-supply = <®_vref_adc>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + status = "okay"; +}; + +&ecspi1 { + cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + eeprom@0 { + compatible = "anvo,anv32e61w", "atmel,at25"; + reg = <0>; + spi-max-frequency = <20000000>; + spi-cpha; + spi-cpol; + pagesize = <1>; + size = <8192>; + address-width = <16>; + }; +}; + +&fec1 { + pinctrl-0 = <&pinctrl_enet1>; + /delete-node/ mdio; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>; + phy-mode = "rmii"; + phy-handle = <ðphy2>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + reg = <1>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET_REF>; + clock-names = "rmii-ref"; + }; + + ethphy2: ethernet-phy@2 { + reg = <2>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET2_REF>; + clock-names = "rmii-ref"; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; +}; + +&i2c4 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + rtc@32 { + compatible = "epson,rx8900"; + reg = <0x32>; + }; +}; + +&pwm8 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm8>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + linux,rs485-enabled-at-boot-time; + rs485-rx-during-tx; + rs485-rts-active-low; + uart-has-rtscts; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbotg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg1>; + dr_mode = "otg"; + srp-disable; + hnp-disable; + adp-disable; + over-current-active-low; + vbus-supply = <®_usb_otg1_vbus>; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + disable-over-current; + vbus-supply = <®_5v>; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; + keep-power-in-suspend; + wakeup-source; + vmmc-supply = <®_3v3>; + voltage-ranges = <3300 3300>; + bus-width = <4>; + no-1-8-v; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; + non-removable; + keep-power-in-suspend; + wakeup-source; + vmmc-supply = <®_3v3>; + voltage-ranges = <3300 3300>; + bus-width = <4>; + no-1-8-v; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>; + + pinctrl_adc1: adc1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0 + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0 + MX6UL_PAD_GPIO1_IO08__GPIO1_IO08 0xb0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x100b1 + MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x100b1 + MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x100b1 + MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x100b1 /* ECSPI1-CS1 */ + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0 + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b009 + >; + }; + + pinctrl_enet2_mdio: enet2mdiogrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0 + MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0 + >; + }; + + pinctrl_flexcan2: flexcan2grp{ + fsl,pins = < + MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020 + MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020 + >; + }; + + pinctrl_gpio: gpiogrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0 /* DOUT1 */ + MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x1b0b0 /* DIN1 */ + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x1b0b0 /* DOUT2 */ + MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x1b0b0 /* DIN2 */ + >; + }; + + pinctrl_gpio_leds: gpioledsgrp { + fsl,pins = < + MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x1b0b0 /* LED H14 */ + MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* LED H15 */ + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* LED H16 */ + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0 + MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001f8b0 + MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001f8b0 + >; + }; + + pinctrl_pwm8: pwm8grp { + fsl,pins = < + MX6UL_PAD_CSI_HSYNC__PWM8_OUT 0x110b0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1 + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6UL_PAD_NAND_DATA04__UART2_DCE_TX 0x1b0b1 + MX6UL_PAD_NAND_DATA05__UART2_DCE_RX 0x1b0b1 + MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS 0x1b0b1 + /* + * mux unused RTS to make sure it doesn't cause + * any interrupts when it is undefined + */ + MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS 0x1b0b1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1 + MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1 + MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b0b1 + MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x1b0b1 + MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_usbotg1: usbotg1 { + fsl,pins = < + MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x1b0b0 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059 + MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x100b1 /* SD1_CD */ + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10059 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x30b0 + >; + }; +}; diff --git a/arch/arm/dts/imx6ul-kontron-n6x1x-s.dtsi b/arch/arm/dts/imx6ul-kontron-n6x1x-s.dtsi new file mode 100644 index 0000000000..4682a79f5b --- /dev/null +++ b/arch/arm/dts/imx6ul-kontron-n6x1x-s.dtsi @@ -0,0 +1,420 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + * Copyright (c) 2019 Krzysztof Kozlowski + */ + +#include + +/ { + gpio-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + led1 { + label = "debug-led1"; + gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; + default-state = "off"; + linux,default-trigger = "heartbeat"; + }; + + led2 { + label = "debug-led2"; + gpios = <&gpio5 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led3 { + label = "debug-led3"; + gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + pwm-beeper { + compatible = "pwm-beeper"; + pwms = <&pwm8 0 5000>; + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_5v: regulator-5v { + compatible = "regulator-fixed"; + regulator-name = "5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_usb_otg1_vbus: regulator-usb-otg1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_vref_adc: regulator-vref-adc { + compatible = "regulator-fixed"; + regulator-name = "vref-adc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&adc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc1>; + num-channels = <3>; + vref-supply = <®_vref_adc>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + status = "okay"; +}; + +&ecspi1 { + cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + eeprom@0 { + compatible = "anvo,anv32e61w", "atmel,at25"; + reg = <0>; + spi-max-frequency = <20000000>; + spi-cpha; + spi-cpol; + pagesize = <1>; + size = <8192>; + address-width = <16>; + }; +}; + +&fec1 { + pinctrl-0 = <&pinctrl_enet1>; + /delete-node/ mdio; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>; + phy-mode = "rmii"; + phy-handle = <ðphy2>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + reg = <1>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET_REF>; + clock-names = "rmii-ref"; + }; + + ethphy2: ethernet-phy@2 { + reg = <2>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET2_REF>; + clock-names = "rmii-ref"; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; +}; + +&i2c4 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + rtc@32 { + compatible = "epson,rx8900"; + reg = <0x32>; + }; +}; + +&pwm8 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm8>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + linux,rs485-enabled-at-boot-time; + rs485-rx-during-tx; + rs485-rts-active-low; + uart-has-rtscts; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbotg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg1>; + dr_mode = "otg"; + srp-disable; + hnp-disable; + adp-disable; + over-current-active-low; + vbus-supply = <®_usb_otg1_vbus>; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + disable-over-current; + vbus-supply = <®_5v>; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; + keep-power-in-suspend; + wakeup-source; + vmmc-supply = <®_3v3>; + voltage-ranges = <3300 3300>; + bus-width = <4>; + no-1-8-v; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; + non-removable; + keep-power-in-suspend; + wakeup-source; + vmmc-supply = <®_3v3>; + voltage-ranges = <3300 3300>; + bus-width = <4>; + no-1-8-v; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>; + + pinctrl_adc1: adc1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0 + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0 + MX6UL_PAD_GPIO1_IO08__GPIO1_IO08 0xb0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x100b1 + MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x100b1 + MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x100b1 + MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x100b1 /* ECSPI1-CS1 */ + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0 + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b009 + >; + }; + + pinctrl_enet2_mdio: enet2mdiogrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0 + MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0 + >; + }; + + pinctrl_flexcan2: flexcan2grp{ + fsl,pins = < + MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020 + MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020 + >; + }; + + pinctrl_gpio: gpiogrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0 /* DOUT1 */ + MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x1b0b0 /* DIN1 */ + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x1b0b0 /* DOUT2 */ + MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x1b0b0 /* DIN2 */ + >; + }; + + pinctrl_gpio_leds: gpioledsgrp { + fsl,pins = < + MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x1b0b0 /* LED H14 */ + MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* LED H15 */ + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* LED H16 */ + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0 + MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001f8b0 + MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001f8b0 + >; + }; + + pinctrl_pwm8: pwm8grp { + fsl,pins = < + MX6UL_PAD_CSI_HSYNC__PWM8_OUT 0x110b0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1 + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6UL_PAD_NAND_DATA04__UART2_DCE_TX 0x1b0b1 + MX6UL_PAD_NAND_DATA05__UART2_DCE_RX 0x1b0b1 + MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS 0x1b0b1 + /* + * mux unused RTS to make sure it doesn't cause + * any interrupts when it is undefined + */ + MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS 0x1b0b1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1 + MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1 + MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b0b1 + MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x1b0b1 + MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_usbotg1: usbotg1 { + fsl,pins = < + MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x1b0b0 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059 + MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x100b1 /* SD1_CD */ + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10059 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x30b0 + >; + }; +}; diff --git a/arch/arm/dts/imx6ul-kontron-n6x1x-som-common.dtsi b/arch/arm/dts/imx6ul-kontron-n6x1x-som-common.dtsi new file mode 100644 index 0000000000..e9ec6b7891 --- /dev/null +++ b/arch/arm/dts/imx6ul-kontron-n6x1x-som-common.dtsi @@ -0,0 +1,124 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + * Copyright (c) 2019 Krzysztof Kozlowski + */ + +#include + +/ { + chosen { + stdout-path = &uart4; + }; + + memory@80000000 { + reg = <0x80000000 0x10000000>; + device_type = "memory"; + }; +}; + +&ecspi2 { + cs-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + status = "okay"; + + spi-flash@0 { + compatible = "mxicy,mx25v8035f", "jedec,spi-nor"; + spi-max-frequency = <50000000>; + reg = <0>; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>; + phy-mode = "rmii"; + phy-handle = <ðphy1>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + reg = <1>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET_REF>; + clock-names = "rmii-ref"; + }; + }; +}; + +&fec2 { + phy-mode = "rmii"; + status = "disabled"; +}; + +&qspi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi>; + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + spi-max-frequency = <104000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + reg = <0>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reset_out>; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x100b1 + MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x100b1 + MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x100b1 + MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x100b1 + >; + }; + + pinctrl_enet1: enet1grp { + fsl,pins = < + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0 + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b009 + >; + }; + + pinctrl_enet1_mdio: enet1mdiogrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0 + MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0 + >; + }; + + pinctrl_qspi: qspigrp { + fsl,pins = < + MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1 + MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1 + MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1 + MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1 + MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1 + MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1 + >; + }; + + pinctrl_reset_out: rstoutgrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x1b0b0 + >; + }; +}; diff --git a/arch/arm/dts/imx6ull-kontron-n641x-s-u-boot.dtsi b/arch/arm/dts/imx6ull-kontron-n641x-s-u-boot.dtsi new file mode 100644 index 0000000000..d3f013c58c --- /dev/null +++ b/arch/arm/dts/imx6ull-kontron-n641x-s-u-boot.dtsi @@ -0,0 +1,7 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + */ + +#include "imx6ul-kontron-n6x1x-s-u-boot.dtsi" diff --git a/arch/arm/dts/imx6ull-kontron-n641x-s.dts b/arch/arm/dts/imx6ull-kontron-n641x-s.dts new file mode 100644 index 0000000000..01aeea4085 --- /dev/null +++ b/arch/arm/dts/imx6ull-kontron-n641x-s.dts @@ -0,0 +1,16 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2019 Kontron Electronics GmbH + */ + +/dts-v1/; + +#include "imx6ull-kontron-n641x-som.dtsi" +#include "imx6ul-kontron-n6x1x-s.dtsi" + +/ { + model = "Kontron N641X S"; + compatible = "kontron,imx6ull-n641x-s", "kontron,imx6ull-n641x-som", + "fsl,imx6ull"; +}; diff --git a/arch/arm/dts/imx6ull-kontron-n641x-som.dtsi b/arch/arm/dts/imx6ull-kontron-n641x-som.dtsi new file mode 100644 index 0000000000..8a64aa9a27 --- /dev/null +++ b/arch/arm/dts/imx6ull-kontron-n641x-som.dtsi @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + */ + +#include "imx6ull.dtsi" +#include "imx6ul-kontron-n6x1x-som-common.dtsi" + +/ { + model = "Kontron N641X SOM"; + compatible = "kontron,imx6ull-n641x-som", "fsl,imx6ull"; +}; diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig index ee73006ae8..b4c8511cb8 100644 --- a/arch/arm/mach-imx/mx6/Kconfig +++ b/arch/arm/mach-imx/mx6/Kconfig @@ -230,6 +230,15 @@ config TARGET_GW_VENTANA imply CMD_SATA imply CMD_SPL +config TARGET_KONTRON_MX6UL + bool "Kontron Electronics SL/BL i.MX6UL/ULL (N63xx/N64xx)" + depends on MX6UL + select BINMAN + select DM + select DM_THERMAL + select SUPPORT_SPL + imply CMD_DM + config TARGET_KOSAGI_NOVENA bool "Kosagi Novena" select BOARD_LATE_INIT @@ -668,6 +677,7 @@ source "board/grinn/liteboard/Kconfig" source "board/phytec/pcm058/Kconfig" source "board/phytec/pcl063/Kconfig" source "board/gateworks/gw_ventana/Kconfig" +source "board/kontron/sl-mx6ul/Kconfig" source "board/kosagi/novena/Kconfig" source "board/softing/vining_2000/Kconfig" source "board/liebherr/display5/Kconfig" diff --git a/board/kontron/sl-mx6ul/Kconfig b/board/kontron/sl-mx6ul/Kconfig new file mode 100644 index 0000000000..4e58de2094 --- /dev/null +++ b/board/kontron/sl-mx6ul/Kconfig @@ -0,0 +1,15 @@ +if TARGET_KONTRON_MX6UL + +config SYS_BOARD + string + default "sl-mx6ul" + +config SYS_VENDOR + string + default "kontron" + +config SYS_CONFIG_NAME + string + default "kontron-sl-mx6ul" + +endif diff --git a/board/kontron/sl-mx6ul/MAINTAINERS b/board/kontron/sl-mx6ul/MAINTAINERS new file mode 100644 index 0000000000..0f8b5512d6 --- /dev/null +++ b/board/kontron/sl-mx6ul/MAINTAINERS @@ -0,0 +1,9 @@ +Kontron SL/BL i.MX6UL/ULL Boards (N63xx/N64xx) +M: Frieder Schrempf +S: Maintained +F: arch/arm/dts/imx6ul-kontron-n6* +F: arch/arm/dts/imx6ull-kontron-n6* +F: board/kontron/sl-mx6ul +F: configs/kontron-sl-mx6ul_defconfig +F: doc/board/kontron/sl-mx6ul.rst +F: include/configs/kontron-sl-mx6ul.h diff --git a/board/kontron/sl-mx6ul/Makefile b/board/kontron/sl-mx6ul/Makefile new file mode 100644 index 0000000000..cae273c930 --- /dev/null +++ b/board/kontron/sl-mx6ul/Makefile @@ -0,0 +1,8 @@ +# SPDX-License-Identifier: GPL-2.0+ +# (C) Copyright 2018 Kontron Electronics GmbH + +ifdef CONFIG_SPL_BUILD +obj-y := spl.o +else +obj-y := sl-mx6ul.o +endif diff --git a/board/kontron/sl-mx6ul/sl-mx6ul.c b/board/kontron/sl-mx6ul/sl-mx6ul.c new file mode 100644 index 0000000000..79d4d8753b --- /dev/null +++ b/board/kontron/sl-mx6ul/sl-mx6ul.c @@ -0,0 +1,85 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 Kontron Electronics GmbH + */ + +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +int dram_init(void) +{ + gd->ram_size = imx_ddr_size(); + + return 0; +} + +int ft_board_setup(void *blob, struct bd_info *bd) +{ + /* + * Overwrite the memory size in the devicetree that is + * passed to the kernel with the actual size detected. + */ + return fdt_fixup_memory(blob, PHYS_SDRAM, gd->ram_size); +} + +static int setup_fec(void) +{ + struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; + int ret; + + /* + * Use 50M anatop loopback REF_CLK1 for ENET1, + * clear gpr1[13], set gpr1[17]. + */ + clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK, + IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK); + + /* + * Use 50M anatop loopback REF_CLK2 for ENET2, + * clear gpr1[14], set gpr1[18]. + */ + clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK, + IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK); + + ret = enable_fec_anatop_clock(0, ENET_50MHZ); + if (ret) + return ret; + + ret = enable_fec_anatop_clock(1, ENET_50MHZ); + if (ret) + return ret; + + return 0; +} + +int board_phy_config(struct phy_device *phydev) +{ + phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190); + + if (phydev->drv->config) + phydev->drv->config(phydev); + + return 0; +} + +int board_early_init_f(void) +{ + enable_qspi_clk(0); + + return 0; +} + +int board_init(void) +{ + /* Address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + + setup_fec(); + + return 0; +} diff --git a/board/kontron/sl-mx6ul/spl.c b/board/kontron/sl-mx6ul/spl.c new file mode 100644 index 0000000000..12b0352146 --- /dev/null +++ b/board/kontron/sl-mx6ul/spl.c @@ -0,0 +1,377 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 Kontron Electronics GmbH + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +enum { + BOARD_TYPE_KTN_N631X = 1, + BOARD_TYPE_KTN_N641X, + BOARD_TYPE_MAX +}; + +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_CD_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) + +#include +#include + +static iomux_v3_cfg_t const usdhc1_pads[] = { + MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + + /* CD */ + MX6_PAD_UART1_RTS_B__GPIO1_IO19 | MUX_PAD_CTRL(USDHC_CD_PAD_CTRL), +}; + +#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 19) + +static iomux_v3_cfg_t const usdhc2_pads[] = { + MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + /* RST */ + MX6_PAD_NAND_ALE__GPIO4_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +#define USDHC2_PWR_GPIO IMX_GPIO_NR(4, 10) + +static struct fsl_esdhc_cfg usdhc_cfg[2] = { + {USDHC1_BASE_ADDR, 0, 4}, + {USDHC2_BASE_ADDR, 0, 4}, +}; + +int board_mmc_getcd(struct mmc *mmc) +{ + struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; + int ret = 0; + + switch (cfg->esdhc_base) { + case USDHC1_BASE_ADDR: + ret = !gpio_get_value(USDHC1_CD_GPIO); + break; + case USDHC2_BASE_ADDR: + // This SDHC interface does not use a CD pin + ret = 1; + break; + } + + return ret; +} + +int board_mmc_init(struct bd_info *bis) +{ + int i, ret; + + /* + * According to the board_mmc_init() the following map is done: + * (U-boot device node) (Physical Port) + * mmc0 USDHC1 + * mmc1 USDHC2 + */ + for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { + switch (i) { + case 0: + imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads)); + gpio_direction_input(USDHC1_CD_GPIO); + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); + break; + case 1: + imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); + gpio_direction_output(USDHC2_PWR_GPIO, 0); + udelay(500); + gpio_direction_output(USDHC2_PWR_GPIO, 1); + usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); + break; + default: + printf("Warning: you configured more USDHC controllers (%d) than supported by the board\n", + i + 1); + return -EINVAL; + } + + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); + if (ret) { + printf("Warning: failed to initialize mmc dev %d\n", i); + return ret; + } + } + return 0; +} + +iomux_v3_cfg_t const ecspi2_pads[] = { + MX6_PAD_CSI_DATA00__ECSPI2_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_CSI_DATA02__ECSPI2_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_CSI_DATA03__ECSPI2_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_CSI_DATA01__GPIO4_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +int board_spi_cs_gpio(unsigned int bus, unsigned int cs) +{ + return (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS) + ? (IMX_GPIO_NR(4, 22)) : -1; +} + +static void setup_spi(void) +{ + gpio_request(IMX_GPIO_NR(4, 22), "spi2_cs0"); + gpio_direction_output(IMX_GPIO_NR(4, 22), 1); + imx_iomux_v3_setup_multiple_pads(ecspi2_pads, ARRAY_SIZE(ecspi2_pads)); + + enable_spi_clk(true, 1); +} + +static iomux_v3_cfg_t const uart4_pads[] = { + MX6_PAD_UART4_TX_DATA__UART4_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_UART4_RX_DATA__UART4_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static void setup_iomux_uart(void) +{ + imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads)); +} + +// DDR 256MB (Hynix H5TQ2G63DFR) +static struct mx6_ddr3_cfg mem_256M_ddr = { + .mem_speed = 800, + .density = 2, + .width = 16, + .banks = 8, + .rowaddr = 14, + .coladdr = 10, + .pagesz = 2, + .trcd = 1350, + .trcmin = 4950, + .trasmin = 3600, +}; + +static struct mx6_mmdc_calibration mx6_mmcd_256M_calib = { + .p0_mpwldectrl0 = 0x00000000, + .p0_mpdgctrl0 = 0x01340134, + .p0_mprddlctl = 0x40405052, + .p0_mpwrdlctl = 0x40404E48, +}; + +// DDR 512MB (Hynix H5TQ4G63DFR) +static struct mx6_ddr3_cfg mem_512M_ddr = { + .mem_speed = 800, + .density = 4, + .width = 16, + .banks = 8, + .rowaddr = 15, + .coladdr = 10, + .pagesz = 2, + .trcd = 1350, + .trcmin = 4950, + .trasmin = 3600, +}; + +static struct mx6_mmdc_calibration mx6_mmcd_512M_calib = { + .p0_mpwldectrl0 = 0x00000000, + .p0_mpdgctrl0 = 0X01440144, + .p0_mprddlctl = 0x40405454, + .p0_mpwrdlctl = 0x40404E4C, +}; + +// Common DDR parameters (256MB and 512MB) +static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = { + .grp_addds = 0x00000028, + .grp_ddrmode_ctl = 0x00020000, + .grp_b0ds = 0x00000028, + .grp_ctlds = 0x00000028, + .grp_b1ds = 0x00000028, + .grp_ddrpke = 0x00000000, + .grp_ddrmode = 0x00020000, + .grp_ddr_type = 0x000c0000, +}; + +static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = { + .dram_dqm0 = 0x00000028, + .dram_dqm1 = 0x00000028, + .dram_ras = 0x00000028, + .dram_cas = 0x00000028, + .dram_odt0 = 0x00000028, + .dram_odt1 = 0x00000028, + .dram_sdba2 = 0x00000000, + .dram_sdclk_0 = 0x00000028, + .dram_sdqs0 = 0x00000028, + .dram_sdqs1 = 0x00000028, + .dram_reset = 0x00000028, +}; + +struct mx6_ddr_sysinfo ddr_sysinfo = { + .dsize = 0, + .cs_density = 20, + .ncs = 1, + .cs1_mirror = 0, + .rtt_wr = 2, + .rtt_nom = 1, /* RTT_Nom = RZQ/2 */ + .walat = 1, /* Write additional latency */ + .ralat = 5, /* Read additional latency */ + .mif3_mode = 3, /* Command prediction working mode */ + .bi_on = 1, /* Bank interleaving enabled */ + .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ + .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ + .ddr_type = DDR_TYPE_DDR3, + .refsel = 0, /* Refresh cycles at 64KHz */ + .refr = 1, /* 2 refresh commands per refresh cycle */ +}; + +static void ccgr_init(void) +{ + struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + writel(0xFFFFFFFF, &ccm->CCGR0); + writel(0xFFFFFFFF, &ccm->CCGR1); + writel(0xFFFFFFFF, &ccm->CCGR2); + writel(0xFFFFFFFF, &ccm->CCGR3); + writel(0xFFFFFFFF, &ccm->CCGR4); + writel(0xFFFFFFFF, &ccm->CCGR5); + writel(0xFFFFFFFF, &ccm->CCGR6); + writel(0xFFFFFFFF, &ccm->CCGR7); +} + +static void spl_dram_init(void) +{ + unsigned int size; + + // DDR RAM connection is always 16 bit wide. Init IOs. + mx6ul_dram_iocfg(16, &mx6_ddr_ioregs, &mx6_grp_ioregs); + + // Try to detect the 512MB RAM chip first. + mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_512M_calib, &mem_512M_ddr); + + // Get the available RAM size + size = get_ram_size((void *)PHYS_SDRAM, SZ_512M); + + gd->ram_size = size; + + if (size == SZ_512M) { + // 512MB RAM was detected + return; + } else if (size == SZ_256M) { + // 256MB RAM was detected, use correct config and calibration + mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_256M_calib, &mem_256M_ddr); + } else { + printf("Invalid DDR RAM size detected: %x\n", size); + } +} + +static int do_board_detect(void) +{ + if (is_mx6ul()) + gd->board_type = BOARD_TYPE_KTN_N631X; + else if (is_mx6ull()) + gd->board_type = BOARD_TYPE_KTN_N641X; + + printf("Kontron SL i.MX6UL%s (N6%s1x) module, %lu MB RAM detected\n", + is_mx6ull() ? "L" : "", is_mx6ull() ? "4" : "3", gd->ram_size / SZ_1M); + + return 0; +} + +void board_init_f(ulong dummy) +{ + ccgr_init(); + + /* setup AIPS and disable watchdog */ + arch_cpu_init(); + + /* iomux and setup of UART and SPI */ + board_early_init_f(); + + /* setup GP timer */ + timer_init(); + + /* UART clocks enabled and gd valid - init serial console */ + preloader_console_init(); + + /* DDR initialization */ + spl_dram_init(); + + /* Clear the BSS. */ + memset(__bss_start, 0, __bss_end - __bss_start); + + /* Detect the board type */ + do_board_detect(); + + /* load/boot image from boot device */ + board_init_r(NULL, 0); +} + +void board_boot_order(u32 *spl_boot_list) +{ + u32 bootdev = spl_boot_device(); + + /* + * The default boot fuse settings use the SD card (MMC1) as primary + * boot device, but allow SPI NOR as a fallback boot device. + * We can't detect the fallback case and spl_boot_device() will return + * BOOT_DEVICE_MMC1 despite the actual boot device being SPI NOR. + * Therefore we try to load U-Boot proper vom SPI NOR after loading + * from MMC has failed. + */ + spl_boot_list[0] = bootdev; + + switch (bootdev) { + case BOOT_DEVICE_MMC1: + case BOOT_DEVICE_MMC2: + spl_boot_list[1] = BOOT_DEVICE_SPI; + break; + } +} + +int board_early_init_f(void) +{ + setup_iomux_uart(); + setup_spi(); + + return 0; +} + +int board_fit_config_name_match(const char *name) +{ + if (gd->board_type == BOARD_TYPE_KTN_N631X && is_mx6ul() && + !strcmp(name, "imx6ul-kontron-n631x-s")) + return 0; + + if (gd->board_type == BOARD_TYPE_KTN_N641X && is_mx6ull() && + !strcmp(name, "imx6ull-kontron-n641x-s")) + return 0; + + return -1; +} diff --git a/configs/kontron-sl-mx6ul_defconfig b/configs/kontron-sl-mx6ul_defconfig new file mode 100644 index 0000000000..28b5d0d671 --- /dev/null +++ b/configs/kontron-sl-mx6ul_defconfig @@ -0,0 +1,109 @@ +CONFIG_ARM=y +CONFIG_ARCH_MX6=y +CONFIG_SYS_TEXT_BASE=0x87800000 +CONFIG_SPL_GPIO=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_SYS_MEMTEST_START=0x80000000 +CONFIG_SYS_MEMTEST_END=0x90000000 +CONFIG_ENV_SIZE=0x10000 +CONFIG_ENV_OFFSET=0xF0000 +CONFIG_ENV_SECT_SIZE=0x10000 +CONFIG_MX6UL=y +CONFIG_TARGET_KONTRON_MX6UL=y +CONFIG_SYS_MALLOC_LEN=0x4000000 +CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="imx6ul-kontron-n631x-s" +CONFIG_SPL_TEXT_BASE=0x00908000 +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_BOOTCOUNT_BOOTLIMIT=3 +CONFIG_SPL=y +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI_SUPPORT=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_FIT=y +CONFIG_SPL_LOAD_FIT=y +# CONFIG_USE_SPL_FIT_GENERATOR is not set +CONFIG_OF_BOARD_SETUP=y +CONFIG_IMX_CONFIG="arch/arm/mach-imx/spl_sd.cfg" +CONFIG_SYS_CONSOLE_IS_IN_ENV=y +CONFIG_BOARD_TYPES=y +CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_SPL_RAW_IMAGE_SUPPORT=y +CONFIG_SPL_LEGACY_IMAGE_SUPPORT=y +CONFIG_SPL_LEGACY_IMAGE_CRC_CHECK=y +CONFIG_SPL_SEPARATE_BSS=y +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x8A +CONFIG_SPL_SPI_LOAD=y +CONFIG_SYS_SPI_U_BOOT_OFFS=0x11400 +CONFIG_SPL_USB_HOST=y +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_USB_SDP_SUPPORT=y +CONFIG_SPL_WATCHDOG=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_MTD=y +CONFIG_CMD_SF_TEST=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_SDP=y +CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_FS_UUID=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nor0=spi1.0,spi-nand0=spi4.0" +CONFIG_MTDPARTS_DEFAULT="mtdparts=spi1.0:128k(spl),832k(u-boot),64k(env);spi4.0:-(UBI)" +CONFIG_CMD_UBI=y +CONFIG_OF_CONTROL=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIST="imx6ul-kontron-n631x-s imx6ull-kontron-n641x-s" +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_USE_ENV_SPI_BUS=y +CONFIG_ENV_SPI_BUS=2 +CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_BOOTCOUNT_ENV=y +CONFIG_DM_I2C=y +CONFIG_FSL_USDHC=y +CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_MTD_SPI_NAND=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SF_DEFAULT_BUS=1 +CONFIG_SF_DEFAULT_MODE=0 +CONFIG_SF_DEFAULT_SPEED=10000000 +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_PHYLIB=y +CONFIG_PHY_MICREL=y +CONFIG_PHY_MICREL_KSZ8XXX=y +CONFIG_DM_ETH=y +CONFIG_DM_ETH_PHY=y +CONFIG_FEC_MXC=y +CONFIG_MII=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_IMX6=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_CONS_INDEX=4 +CONFIG_MXC_UART=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_FSL_QSPI=y +CONFIG_MXC_SPI=y +CONFIG_IMX_THERMAL=y +CONFIG_USB=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_CI_UDC=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_FDT_FIXUP_PARTITIONS=y diff --git a/doc/board/kontron/index.rst b/doc/board/kontron/index.rst index 543b22e2f5..c3fadcef76 100644 --- a/doc/board/kontron/index.rst +++ b/doc/board/kontron/index.rst @@ -7,3 +7,4 @@ Kontron :maxdepth: 2 sl28 + sl-mx6ul diff --git a/doc/board/kontron/sl-mx6ul.rst b/doc/board/kontron/sl-mx6ul.rst new file mode 100644 index 0000000000..b0b0f44db2 --- /dev/null +++ b/doc/board/kontron/sl-mx6ul.rst @@ -0,0 +1,43 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Kontron Electronics SL i.MX6UL/ULL SoM +====================================== + +The Kontron SoM-Line i.MX6UL/ULL (N6x1x) by Kontron Electronics GmbH is a SoM module +with either an i.MX6UL or i.MX6ULL SoC, 256/512 MB DDR3 RAM, SPI NOR, SPI NAND and Ethernet PHY. + +The matching evaluation boards (Board-Line) have two Ethernet ports, USB 2.0, +RGB, SD card, CAN, RS485, RS232 and much more. + +Quick Start +----------- + +- Build U-Boot +- Boot + +Build U-Boot +^^^^^^^^^^^^ + +.. code-block:: bash + + $ make kontron-sl-mx6ul_defconfig + $ make + +Burn the flash.bin to SD card at an offset of 1 KiB: + +.. code-block:: bash + + $ dd if=flash.bin of=/dev/sd[x] bs=1K seek=1 conv=notrunc + +Boot +^^^^ + +Put the SD card in the slot on the board and apply power. + +Further Information +------------------- + +The bootloader configuration is setup to be used with kernel FIT images. Legacy +images might not be working out of the box. + +Please see https://docs.kontron-electronics.de for further vendor documentation. diff --git a/include/configs/kontron-sl-mx6ul.h b/include/configs/kontron-sl-mx6ul.h new file mode 100644 index 0000000000..65aa250894 --- /dev/null +++ b/include/configs/kontron-sl-mx6ul.h @@ -0,0 +1,77 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2018 Kontron Electronics GmbH + * + * Configuration settings for the Kontron i.MX6UL boards/SoMs. + */ +#ifndef __KONTRON_MX6UL_CONFIG_H +#define __KONTRON_MX6UL_CONFIG_H + +#include +#include + +#include "mx6_common.h" +#ifdef CONFIG_SPL_BUILD +#include "imx6_spl.h" +#endif + +/* RAM */ +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM + +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +#define CONFIG_SYS_UBOOT_BASE CONFIG_SYS_TEXT_BASE + +/* Board and environment settings */ +#define CONFIG_MXC_UART_BASE UART4_BASE +#define CONFIG_HOSTNAME "kontron-mx6ul" +#define CONFIG_ETHPRIME "eth0" + +#ifdef CONFIG_USB_EHCI_HCD +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) +#define CONFIG_MXC_USB_FLAGS 0 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 +#endif + +/* Boot order for distro boot */ +#ifndef CONFIG_SPL_BUILD +#define BOOT_TARGET_DEVICES(func) \ + func(MMC, mmc, 1) \ + func(MMC, mmc, 0) \ + func(UBIFS, ubifs, 0) \ + func(USB, usb, 0) \ + func(PXE, pxe, na) \ + func(DHCP, dhcp, na) +#include +#else +#define BOOTENV +#endif + +/* MMC Configs */ +#ifdef CONFIG_FSL_USDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC1_BASE_ADDR +#define CONFIG_SYS_FSL_USDHC_NUM 2 +#define CONFIG_SYS_MMC_IMG_LOAD_PART 1 +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "kernel_addr_r=0x82000000\0" \ + "ramdisk_addr_r=0x88080000\0" \ + "pxefile_addr_r=0x80100000\0" \ + "scriptaddr=0x80100000\0" \ + "bootdelay=3\0" \ + "ethact=" CONFIG_ETHPRIME "\0" \ + "hostname=" CONFIG_HOSTNAME "\0" \ + BOOTENV + +#endif /* __KONTRON_MX6UL_CONFIG_H */