From: Timur Tabi Date: Thu, 4 Aug 2011 23:03:41 +0000 (-0500) Subject: powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=e46fedfeb214d118b9983d11fcc929ed49f5ccd7;p=u-boot.git powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS. This is necessary for the assembly-language code that relocates CCSR, since the assembler does not understand 64-bit constants. CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it should not be defined in a board header file. Similarly, CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so it should also not be defined in the board header file. CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT, and so CCSR will not be relocated. Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot builds (e.g. NAND) are required to relocate CCSR only during the last stage (i.e. the "real" U-Boot). All other stages should define CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated. README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala --- diff --git a/README b/README index a43da97a41..91b6695cf9 100644 --- a/README +++ b/README @@ -2862,6 +2862,43 @@ Low Level (hardware related) configuration options: and RPXsuper) to be able to adjust the position of the IMMR register after a reset. +- CONFIG_SYS_CCSRBAR_DEFAULT: + Default (power-on reset) physical address of CCSR on Freescale + PowerPC SOCs. + +- CONFIG_SYS_CCSRBAR: + Virtual address of CCSR. On a 32-bit build, this is typically + the same value as CONFIG_SYS_CCSRBAR_DEFAULT. + + CONFIG_SYS_DEFAULT_IMMR must also be set to this value, + for cross-platform code that uses that macro instead. + +- CONFIG_SYS_CCSRBAR_PHYS: + Physical address of CCSR. CCSR can be relocated to a new + physical address, if desired. In this case, this macro should + be set to that address. Otherwise, it should be set to the + same value as CONFIG_SYS_CCSRBAR_DEFAULT. For example, CCSR + is typically relocated on 36-bit builds. It is recommended + that this macro be defined via the _HIGH and _LOW macros: + + #define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH + * 1ull) << 32 | CONFIG_SYS_CCSRBAR_PHYS_LOW) + +- CONFIG_SYS_CCSRBAR_PHYS_HIGH: + Bits 33-36 of CONFIG_SYS_CCSRBAR_PHYS. This value is typically + either 0 (32-bit build) or 0xF (36-bit build). This macro is + used in assembly code, so it must not contain typecasts or + integer size suffixes (e.g. "ULL"). + +- CONFIG_SYS_CCSRBAR_PHYS_LOW: + Lower 32-bits of CONFIG_SYS_CCSRBAR_PHYS. This macro is + used in assembly code, so it must not contain typecasts or + integer size suffixes (e.g. "ULL"). + +- CONFIG_SYS_CCSR_DO_NOT_RELOCATE: + If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be + forced to a value that ensures that CCSR is not relocated. + - Floppy Disk Support: CONFIG_SYS_FDC_DRIVE_NUMBER diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h index 7de8f744e5..691c075582 100644 --- a/arch/powerpc/include/asm/config_mpc85xx.h +++ b/arch/powerpc/include/asm/config_mpc85xx.h @@ -23,6 +23,10 @@ /* SoC specific defines for Freescale MPC85xx (PQ3) and QorIQ processors */ +#ifdef CONFIG_SYS_CCSRBAR_DEFAULT +#error "Do not define CONFIG_SYS_CCSRBAR_DEFAULT in the board header file." +#endif + /* Number of TLB CAM entries we have on FSL Book-E chips */ #if defined(CONFIG_E500MC) #define CONFIG_SYS_NUM_TLBCAMS 64 @@ -34,34 +38,41 @@ #define CONFIG_MAX_CPUS 1 #define CONFIG_SYS_FSL_NUM_LAWS 12 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #elif defined(CONFIG_MPC8540) #define CONFIG_MAX_CPUS 1 #define CONFIG_SYS_FSL_NUM_LAWS 8 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #elif defined(CONFIG_MPC8541) #define CONFIG_MAX_CPUS 1 #define CONFIG_SYS_FSL_NUM_LAWS 8 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #elif defined(CONFIG_MPC8544) #define CONFIG_MAX_CPUS 1 #define CONFIG_SYS_FSL_NUM_LAWS 10 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #elif defined(CONFIG_MPC8548) #define CONFIG_MAX_CPUS 1 #define CONFIG_SYS_FSL_NUM_LAWS 10 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #elif defined(CONFIG_MPC8555) #define CONFIG_MAX_CPUS 1 #define CONFIG_SYS_FSL_NUM_LAWS 8 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #elif defined(CONFIG_MPC8560) #define CONFIG_MAX_CPUS 1 #define CONFIG_SYS_FSL_NUM_LAWS 8 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #elif defined(CONFIG_MPC8568) #define CONFIG_MAX_CPUS 1 @@ -70,6 +81,7 @@ #define QE_MURAM_SIZE 0x10000UL #define MAX_QE_RISC 2 #define QE_NUM_OF_SNUM 28 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #elif defined(CONFIG_MPC8569) #define CONFIG_MAX_CPUS 1 @@ -78,11 +90,13 @@ #define QE_MURAM_SIZE 0x20000UL #define MAX_QE_RISC 4 #define QE_NUM_OF_SNUM 46 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #elif defined(CONFIG_MPC8572) #define CONFIG_MAX_CPUS 2 #define CONFIG_SYS_FSL_NUM_LAWS 12 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_DDR_115 #define CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 @@ -106,6 +120,7 @@ #define CONFIG_TSECV2 #define CONFIG_FSL_PCIE_DISABLE_ASPM #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 @@ -116,6 +131,7 @@ #define CONFIG_TSECV2 #define CONFIG_FSL_PCIE_DISABLE_ASPM #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define QE_MURAM_SIZE 0x6000UL @@ -128,6 +144,7 @@ #define CONFIG_SYS_FSL_NUM_LAWS 12 #define CONFIG_TSECV2 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_FSL_SATA_ERRATUM_A001 @@ -151,6 +168,7 @@ #define CONFIG_TSECV2 #define CONFIG_FSL_PCIE_DISABLE_ASPM #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 @@ -166,6 +184,7 @@ #define QE_MURAM_SIZE 0x6000UL #define MAX_QE_RISC 1 #define QE_NUM_OF_SNUM 28 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* P1017 is single core version of P1023 */ #elif defined(CONFIG_P1017) @@ -179,6 +198,7 @@ #define CONFIG_SYS_BMAN_NUM_PORTALS 3 #define CONFIG_SYS_FM_MURAM_SIZE 0x10000 #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff600000 #elif defined(CONFIG_P1020) #define CONFIG_MAX_CPUS 2 @@ -186,6 +206,7 @@ #define CONFIG_TSECV2 #define CONFIG_FSL_PCIE_DISABLE_ASPM #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 @@ -195,6 +216,7 @@ #define CONFIG_TSECV2 #define CONFIG_FSL_PCIE_DISABLE_ASPM #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define QE_MURAM_SIZE 0x6000UL @@ -206,6 +228,7 @@ #define CONFIG_SYS_FSL_NUM_LAWS 12 #define CONFIG_TSECV2 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_FSL_SATA_ERRATUM_A001 @@ -221,6 +244,7 @@ #define CONFIG_SYS_BMAN_NUM_PORTALS 3 #define CONFIG_SYS_FM_MURAM_SIZE 0x10000 #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff600000 /* P1024 is lower end variant of P1020 */ #elif defined(CONFIG_P1024) @@ -229,6 +253,7 @@ #define CONFIG_TSECV2 #define CONFIG_FSL_PCIE_DISABLE_ASPM #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 @@ -239,6 +264,7 @@ #define CONFIG_TSECV2 #define CONFIG_FSL_PCIE_DISABLE_ASPM #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define QE_MURAM_SIZE 0x6000UL @@ -250,6 +276,7 @@ #define CONFIG_MAX_CPUS 1 #define CONFIG_SYS_FSL_NUM_LAWS 12 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ERRATUM_ESDHC_A001 @@ -257,6 +284,7 @@ #define CONFIG_MAX_CPUS 2 #define CONFIG_SYS_FSL_NUM_LAWS 12 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ERRATUM_ESDHC_A001 @@ -271,6 +299,7 @@ #define CONFIG_SYS_FM_MURAM_SIZE 0x28000 #define CONFIG_SYS_FSL_TBCLK_DIV 32 #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 #define CONFIG_SYS_FSL_USB1_PHY_ENABLE #define CONFIG_SYS_FSL_USB2_PHY_ENABLE #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY @@ -288,6 +317,7 @@ #define CONFIG_SYS_FM_MURAM_SIZE 0x28000 #define CONFIG_SYS_FSL_TBCLK_DIV 32 #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 #define CONFIG_SYS_FSL_USB1_PHY_ENABLE #define CONFIG_SYS_FSL_USB2_PHY_ENABLE #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY @@ -305,6 +335,7 @@ #define CONFIG_SYS_FM_MURAM_SIZE 0x28000 #define CONFIG_SYS_FSL_TBCLK_DIV 32 #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 #define CONFIG_SYS_FSL_USB1_PHY_ENABLE #define CONFIG_SYS_FSL_USB2_PHY_ENABLE #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY @@ -318,6 +349,7 @@ #define CONFIG_SYS_FM_MURAM_SIZE 0x28000 #define CONFIG_SYS_FSL_TBCLK_DIV 16 #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,p4080-pcie" +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 #elif defined(CONFIG_PPC_P4080) #define CONFIG_MAX_CPUS 8 @@ -333,6 +365,7 @@ #define CONFIG_SYS_FM_MURAM_SIZE 0x28000 #define CONFIG_SYS_FSL_TBCLK_DIV 16 #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,p4080-pcie" +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 #define CONFIG_SYS_FSL_ERRATUM_CPC_A002 #define CONFIG_SYS_FSL_ERRATUM_CPC_A003 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003 @@ -359,6 +392,7 @@ #define CONFIG_SYS_FM_MURAM_SIZE 0x28000 #define CONFIG_SYS_FSL_TBCLK_DIV 32 #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 #define CONFIG_SYS_FSL_USB1_PHY_ENABLE #define CONFIG_SYS_FSL_USB2_PHY_ENABLE #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY @@ -376,6 +410,7 @@ #define CONFIG_SYS_FM_MURAM_SIZE 0x28000 #define CONFIG_SYS_FSL_TBCLK_DIV 32 #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 #define CONFIG_SYS_FSL_USB1_PHY_ENABLE #define CONFIG_SYS_FSL_USB2_PHY_ENABLE #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY @@ -385,4 +420,8 @@ #error Processor type not defined for this platform #endif +#ifndef CONFIG_SYS_CCSRBAR_DEFAULT +#error "CONFIG_SYS_CCSRBAR_DEFAULT is not defined for this platform." +#endif + #endif /* _ASM_MPC85xx_CONFIG_H_ */ diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h index 783ed518e5..f3d325a0c9 100644 --- a/include/configs/MPC8536DS.h +++ b/include/configs/MPC8536DS.h @@ -127,22 +127,11 @@ #define CONFIG_SYS_L2_SIZE (512 << 10) #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull /* physical addr of CCSRBAR */ -#else -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR -#endif -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xffe00000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR #if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL) -#define CONFIG_SYS_CCSRBAR_DEFAULT CONFIG_SYS_CCSRBAR -#else -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE #endif /* DDR Setup */ diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h index e1d933ec49..fc0edacede 100644 --- a/include/configs/MPC8540ADS.h +++ b/include/configs/MPC8540ADS.h @@ -89,15 +89,8 @@ #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ #define CONFIG_SYS_MEMTEST_END 0x00400000 - -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xe0000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ #define CONFIG_FSL_DDR1 diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index 5918e644d1..ae19036d87 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -62,14 +62,8 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00400000 -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xe0000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ #define CONFIG_FSL_DDR1 diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index b25fb55a46..6b03d27410 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -74,14 +74,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_MEMTEST_END 0x00400000 #define CONFIG_PANIC_HANG /* do not reset board on panic */ -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xe0000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ #define CONFIG_FSL_DDR2 diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h index c9a0f60580..aca77ff6b9 100644 --- a/include/configs/MPC8548CDS.h +++ b/include/configs/MPC8548CDS.h @@ -77,14 +77,8 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00400000 -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xe0000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ #define CONFIG_FSL_DDR2 diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h index 4c580a37e3..93d4c3e5fb 100644 --- a/include/configs/MPC8555CDS.h +++ b/include/configs/MPC8555CDS.h @@ -62,14 +62,8 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00400000 -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xe0000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ #define CONFIG_FSL_DDR1 diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index f55ef9d796..e03fea3cc9 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -86,15 +86,8 @@ #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ #define CONFIG_SYS_MEMTEST_END 0x00400000 - -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xe0000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ #define CONFIG_FSL_DDR1 diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index f7df7f0388..cf0ea47e7a 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -71,14 +71,8 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00400000 -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xe0000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ #define CONFIG_FSL_DDR2 diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h index fa626bb977..dd7278c4b8 100644 --- a/include/configs/MPC8569MDS.h +++ b/include/configs/MPC8569MDS.h @@ -105,20 +105,11 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SYS_L2_SIZE (512 << 10) #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR - /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR - /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xe0000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR #if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL) -#define CONFIG_SYS_CCSRBAR_DEFAULT CONFIG_SYS_CCSRBAR -#else -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE #endif /* DDR Setup */ diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index bb8fb669c3..6067e60852 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -112,22 +112,11 @@ #define CONFIG_SYS_L2_SIZE (512 << 10) #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull /* physical addr of CCSRBAR */ -#else -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#endif -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xffe00000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR #if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL) -#define CONFIG_SYS_CCSRBAR_DEFAULT CONFIG_SYS_CCSRBAR -#else -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE #endif /* DDR Setup */ diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h index a118975528..a3cccf4c3f 100644 --- a/include/configs/P1022DS.h +++ b/include/configs/P1022DS.h @@ -64,18 +64,8 @@ #define CONFIG_SYS_MEMTEST_START 0x00000000 #define CONFIG_SYS_MEMTEST_END 0x7fffffff -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull -#else -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR -#endif -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR +#define CONFIG_SYS_CCSRBAR 0xffe00000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ #define CONFIG_DDR_SPD diff --git a/include/configs/P1023RDS.h b/include/configs/P1023RDS.h index 95f3a2c181..24042dfb65 100644 --- a/include/configs/P1023RDS.h +++ b/include/configs/P1023RDS.h @@ -99,15 +99,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SYS_LBC_LBCR 0x00000000 /* Implement conversion of addresses in the LBC */ -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff600000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xff600000 /* relocated CCSRBAR */ -/* physical addr of CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ /* DDR Setup */ #define CONFIG_VERY_BIG_RAM diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h index df88b79bbe..3ffdb1a02a 100644 --- a/include/configs/P1_P2_RDB.h +++ b/include/configs/P1_P2_RDB.h @@ -148,24 +148,11 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_L2_SIZE (512 << 10) #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull -#else -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR -#endif - /* CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */ - /* CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xffe00000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR #if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL) -#define CONFIG_SYS_CCSRBAR_DEFAULT CONFIG_SYS_CCSRBAR -#else -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE #endif /* DDR Setup */ diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h index 90fe7c4047..f6b788e578 100644 --- a/include/configs/P2020DS.h +++ b/include/configs/P2020DS.h @@ -118,18 +118,8 @@ #define CONFIG_SYS_L2_SIZE (512 << 10) #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull /* physical addr of CCSRBAR */ -#else -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#endif -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xffe00000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ #define CONFIG_VERY_BIG_RAM diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h index 638dbe7a6d..03dbe55c3b 100644 --- a/include/configs/P2041RDB.h +++ b/include/configs/P2041RDB.h @@ -138,20 +138,6 @@ #define CONFIG_SYS_L3_SIZE (1024 << 10) #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xfe000000 /* relocated CCSRBAR */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_CCSRBAR_PHYS 0xffe000000ull -#else -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR -#endif -/* PQII uses CONFIG_SYS_IMMR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR - #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_DCSRBAR 0xf0000000 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h index 72559c0c02..b5612d66ca 100644 --- a/include/configs/SBC8540.h +++ b/include/configs/SBC8540.h @@ -94,20 +94,6 @@ #error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC." #endif -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ - -#if XXX - #define CONFIG_SYS_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */ -#else - #define CONFIG_SYS_CCSRBAR 0xff700000 /* default CCSRBAR */ -#endif -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ - #define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */ /* DDR Setup */ diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h index b336723f55..fe6b728104 100644 --- a/include/configs/TQM85xx.h +++ b/include/configs/TQM85xx.h @@ -130,18 +130,12 @@ #define CONFIG_SYS_MEMTEST_START 0x00000000 #define CONFIG_SYS_MEMTEST_END 0x10000000 -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ #ifdef CONFIG_TQM_BIGFLASH -#define CONFIG_SYS_CCSRBAR 0xA0000000 /* relocated CCSRBAR */ -#else /* !CONFIG_TQM_BIGFLASH */ -#define CONFIG_SYS_CCSRBAR 0xE0000000 /* relocated CCSRBAR */ -#endif /* CONFIG_TQM_BIGFLASH */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xA0000000 +#else +#define CONFIG_SYS_CCSRBAR 0xE0000000 +#endif +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* * DDR Setup diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h index adf9906bce..eb89b30b36 100644 --- a/include/configs/corenet_ds.h +++ b/include/configs/corenet_ds.h @@ -144,19 +144,6 @@ #define CONFIG_SYS_L3_SIZE (1024 << 10) #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xfe000000 /* relocated CCSRBAR */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_CCSRBAR_PHYS 0xffe000000ull /* physical addr of CCSRBAR */ -#else -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#endif -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ - #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_DCSRBAR 0xf0000000 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull diff --git a/include/configs/mpq101.h b/include/configs/mpq101.h index e76ca73d47..f0ed4d1083 100644 --- a/include/configs/mpq101.h +++ b/include/configs/mpq101.h @@ -64,20 +64,8 @@ #define CONFIG_SYS_CLK_FREQ 33000000 /* sysclk for MPC85xx */ -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 -#define CONFIG_SYS_CCSRBAR 0xe0000000 - -#ifdef CONFIG_PHYS_64BIT -# define CONFIG_SYS_CCSRBAR_PHYS 0xfe0000000ull -#else -# define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR -#endif - -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR +#define CONFIG_SYS_CCSRBAR 0xe0000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ #define CONFIG_FSL_DDR2 diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h index 7bf9fc76c2..4ec323ecec 100644 --- a/include/configs/sbc8548.h +++ b/include/configs/sbc8548.h @@ -103,14 +103,8 @@ #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00400000 -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xe0000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ #define CONFIG_FSL_DDR2 diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h index 435b148f3c..e0af0d26a8 100644 --- a/include/configs/sbc8560.h +++ b/include/configs/sbc8560.h @@ -92,20 +92,6 @@ #error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC." #endif -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ - -#if XXX - #define CONFIG_SYS_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */ -#else - #define CONFIG_SYS_CCSRBAR 0xff700000 /* default CCSRBAR */ -#endif -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ - #define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */ /* DDR Setup */ diff --git a/include/configs/socrates.h b/include/configs/socrates.h index 5f2fb1e927..af62aea7a6 100644 --- a/include/configs/socrates.h +++ b/include/configs/socrates.h @@ -91,14 +91,8 @@ #define CONFIG_SYS_MEMTEST_START 0x00400000 #define CONFIG_SYS_MEMTEST_END 0x00C00000 -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xE0000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xE0000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ #define CONFIG_FSL_DDR2 diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h index fc3881d22b..66738d5953 100644 --- a/include/configs/stxgp3.h +++ b/include/configs/stxgp3.h @@ -109,12 +109,9 @@ #ifdef CONFIG_SYS_RAMBOOT #define CONFIG_SYS_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */ -#else -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #endif -#define CONFIG_SYS_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xfdf00000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ #define CONFIG_FSL_DDR1 diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h index 141da26473..a421ba43b2 100644 --- a/include/configs/stxssa.h +++ b/include/configs/stxssa.h @@ -121,12 +121,10 @@ #ifdef CONFIG_SYS_RAMBOOT #define CONFIG_SYS_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */ -#else -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #endif -#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ + +#define CONFIG_SYS_CCSRBAR 0xe0000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ #define CONFIG_FSL_DDR1 diff --git a/include/configs/xpedite520x.h b/include/configs/xpedite520x.h index b6b391f89f..42517c9da8 100644 --- a/include/configs/xpedite520x.h +++ b/include/configs/xpedite520x.h @@ -78,14 +78,8 @@ #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_ENABLE_36BIT_PHYS 1 -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xef000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* * Diagnostics diff --git a/include/configs/xpedite537x.h b/include/configs/xpedite537x.h index a74766dcec..202f209a7b 100644 --- a/include/configs/xpedite537x.h +++ b/include/configs/xpedite537x.h @@ -96,14 +96,8 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_ENABLE_36BIT_PHYS 1 -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xef000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* * Diagnostics diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h index 6588867b87..0c2e7edb23 100644 --- a/include/configs/xpedite550x.h +++ b/include/configs/xpedite550x.h @@ -93,14 +93,8 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_ENABLE_36BIT_PHYS 1 -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xef000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* * Diagnostics diff --git a/include/mpc85xx.h b/include/mpc85xx.h index 2495b99c31..11d898527b 100644 --- a/include/mpc85xx.h +++ b/include/mpc85xx.h @@ -26,4 +26,46 @@ #define SCCR_DFBRG10 0x00000002 /* BRGCLK division by 64 */ #define SCCR_DFBRG11 0x00000003 /* BRGCLK division by 256 */ +/* + * Define default values for some CCSR macros to make header files cleaner* + * + * To completely disable CCSR relocation in a board header file, define + * CONFIG_SYS_CCSR_DO_NOT_RELOCATE. This will force CONFIG_SYS_CCSRBAR_PHYS + * to a value that is the same as CONFIG_SYS_CCSRBAR. + */ + +#ifdef CONFIG_SYS_CCSRBAR_PHYS +#error "Do not define CONFIG_SYS_CCSRBAR_PHYS directly. Use \ +CONFIG_SYS_CCSRBAR_PHYS_LOW and/or CONFIG_SYS_CCSRBAR_PHYS_HIGH instead." +#endif + +#ifdef CONFIG_SYS_CCSR_DO_NOT_RELOCATE +#undef CONFIG_SYS_CCSRBAR_PHYS_HIGH +#undef CONFIG_SYS_CCSRBAR_PHYS_LOW +#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0 +#endif + +#ifndef CONFIG_SYS_CCSRBAR +#define CONFIG_SYS_CCSRBAR CONFIG_SYS_CCSRBAR_DEFAULT +#endif + +#ifndef CONFIG_SYS_CCSRBAR_PHYS_HIGH +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0xf +#else +#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0 +#endif +#endif + +#ifndef CONFIG_SYS_CCSRBAR_PHYS_LOW +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR_DEFAULT +#endif + +#define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH * 1ull) << 32 | \ + CONFIG_SYS_CCSRBAR_PHYS_LOW) + +#ifndef CONFIG_SYS_IMMR +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR +#endif + #endif /* __MPC85xx_H__ */