From: Stefan Roese Date: Thu, 19 Nov 2015 06:46:15 +0000 (+0100) Subject: net: mvneta: Convert to driver model X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=e3b9c98a23ca9;p=u-boot.git net: mvneta: Convert to driver model Update this driver to support driver model. As all MVEBU boards using this driver are converted with this patch, the non-driver-model code can be removed completely. This is also the reason why this patch is quite big and includes a) the driver change and b) the platform change. As its not git-bisect save otherwise. With this conversion, some parameters are now extracted from the DT instread of using the config header defines. The supported properties right now are: PHY-mode ("phy-mode") and PHY-address ("reg"). The base addresses for the ethernet controllers can be removed from the header files as well. Please note that this patch also removes the E1000 network driver from some MVEBU config headers. This is necessary, as with DM_ETH configured and the e1000 driver enabled, the PCI driver also needs to support DM. But the MVEBU PCI(e) driver still needs to get ported to DM. When this is done, the E1000 driver can be enabled again. Signed-off-by: Stefan Roese Cc: Luka Perkov Cc: Dirk Eibach Cc: Joe Hershberger Cc: Simon Glass --- diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 68ae6b6d06..ab621cca7d 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -117,6 +117,7 @@ config ARCH_MVEBU select OF_CONTROL select OF_SEPARATE select DM + select DM_ETH select DM_SERIAL select DM_SPI select DM_SPI_FLASH diff --git a/arch/arm/mach-mvebu/cpu.c b/arch/arm/mach-mvebu/cpu.c index 895ad929b1..751dabc5a6 100644 --- a/arch/arm/mach-mvebu/cpu.c +++ b/arch/arm/mach-mvebu/cpu.c @@ -326,30 +326,6 @@ int arch_misc_init(void) } #endif /* CONFIG_ARCH_MISC_INIT */ -#ifdef CONFIG_MVNETA -int cpu_eth_init(bd_t *bis) -{ - u32 enet_base[] = { MVEBU_EGIGA0_BASE, MVEBU_EGIGA1_BASE, - MVEBU_EGIGA2_BASE, MVEBU_EGIGA3_BASE }; - u8 phy_addr[] = CONFIG_PHY_ADDR; - int i; - - /* - * Only Armada XP supports all 4 ethernet interfaces. A38x has - * slightly different base addresses for its 2-3 interfaces. - */ - if (mvebu_soc_family() != MVEBU_SOC_AXP) { - enet_base[1] = MVEBU_EGIGA2_BASE; - enet_base[2] = MVEBU_EGIGA3_BASE; - } - - for (i = 0; i < ARRAY_SIZE(phy_addr); i++) - mvneta_initialize(bis, enet_base[i], i, phy_addr[i]); - - return 0; -} -#endif - #ifdef CONFIG_MV_SDHCI int board_mmc_init(bd_t *bis) { diff --git a/arch/arm/mach-mvebu/include/mach/soc.h b/arch/arm/mach-mvebu/include/mach/soc.h index 3cdb1f24d7..2be8cbac3f 100644 --- a/arch/arm/mach-mvebu/include/mach/soc.h +++ b/arch/arm/mach-mvebu/include/mach/soc.h @@ -57,13 +57,9 @@ #define MVEBU_CPU_WIN_BASE (MVEBU_REGISTER(0x20000)) #define MVEBU_SDRAM_BASE (MVEBU_REGISTER(0x20180)) #define MVEBU_TIMER_BASE (MVEBU_REGISTER(0x20300)) -#define MVEBU_EGIGA2_BASE (MVEBU_REGISTER(0x30000)) -#define MVEBU_EGIGA3_BASE (MVEBU_REGISTER(0x34000)) #define MVEBU_REG_PCIE_BASE (MVEBU_REGISTER(0x40000)) #define MVEBU_AXP_USB_BASE (MVEBU_REGISTER(0x50000)) #define MVEBU_USB20_BASE (MVEBU_REGISTER(0x58000)) -#define MVEBU_EGIGA0_BASE (MVEBU_REGISTER(0x70000)) -#define MVEBU_EGIGA1_BASE (MVEBU_REGISTER(0x74000)) #define MVEBU_AXP_SATA_BASE (MVEBU_REGISTER(0xa0000)) #define MVEBU_SATA0_BASE (MVEBU_REGISTER(0xa8000)) #define MVEBU_NAND_BASE (MVEBU_REGISTER(0xd0000)) diff --git a/board/Marvell/db-mv784mp-gp/db-mv784mp-gp.c b/board/Marvell/db-mv784mp-gp/db-mv784mp-gp.c index d7aa1499ad..9305284117 100644 --- a/board/Marvell/db-mv784mp-gp/db-mv784mp-gp.c +++ b/board/Marvell/db-mv784mp-gp/db-mv784mp-gp.c @@ -87,40 +87,32 @@ int board_eth_init(bd_t *bis) return pci_eth_init(bis); } -#ifdef CONFIG_RESET_PHY_R -/* Configure and enable MV88E1545 PHY */ -void reset_phy(void) +int board_phy_config(struct phy_device *phydev) { - u8 phy_addr[] = CONFIG_PHY_ADDR; - u16 devadr = phy_addr[0]; - char *name = "neta0"; u16 reg; - if (miiphy_set_current_dev(name)) - return; - /* Enable QSGMII AN */ /* Set page to 4 */ - miiphy_write(name, devadr, 0x16, 4); + phy_write(phydev, MDIO_DEVAD_NONE, 0x16, 4); /* Enable AN */ - miiphy_write(name, devadr, 0x0, 0x1140); + phy_write(phydev, MDIO_DEVAD_NONE, 0x0, 0x1140); /* Set page to 0 */ - miiphy_write(name, devadr, 0x16, 0); + phy_write(phydev, MDIO_DEVAD_NONE, 0x16, 0); /* Phy C_ANEG */ - miiphy_read(name, devadr, 0x4, ®); + reg = phy_read(phydev, MDIO_DEVAD_NONE, 0x4); reg |= 0x1E0; - miiphy_write(name, devadr, 0x4, reg); + phy_write(phydev, MDIO_DEVAD_NONE, 0x4, reg); /* Soft-Reset */ - miiphy_write(name, devadr, 22, 0x0000); - miiphy_write(name, devadr, 0, 0x9140); + phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x0000); + phy_write(phydev, MDIO_DEVAD_NONE, 0, 0x9140); /* Power up the phy */ - miiphy_read(name, devadr, ETH_PHY_CTRL_REG, ®); + reg = phy_read(phydev, MDIO_DEVAD_NONE, ETH_PHY_CTRL_REG); reg &= ~(ETH_PHY_CTRL_POWER_DOWN_MASK); - miiphy_write(name, devadr, ETH_PHY_CTRL_REG, reg); + phy_write(phydev, MDIO_DEVAD_NONE, ETH_PHY_CTRL_REG, reg); - printf("88E1545 Initialized on %s\n", name); + printf("88E1545 Initialized\n"); + return 0; } -#endif /* CONFIG_RESET_PHY_R */ diff --git a/board/maxbcm/maxbcm.c b/board/maxbcm/maxbcm.c index 119ba4c6c8..db6ad99efe 100644 --- a/board/maxbcm/maxbcm.c +++ b/board/maxbcm/maxbcm.c @@ -138,17 +138,15 @@ int checkboard(void) return 0; } -#ifdef CONFIG_RESET_PHY_R /* Configure and enable MV88E6185 switch */ -void reset_phy(void) +int board_phy_config(struct phy_device *phydev) { - char *name = "neta0"; - - if (miiphy_set_current_dev(name)) - return; - - /* todo: fill this with the real setup / config code */ - - printf("88E6185 Initialized on %s\n", name); + /* + * todo: + * Fill this with the real setup / config code. + * Please see board/Marvell/db-mv784mp-gp/db-mv784mp-gp.c + * for details. + */ + printf("88E6185 Initialized\n"); + return 0; } -#endif /* CONFIG_RESET_PHY_R */ diff --git a/drivers/net/mvneta.c b/drivers/net/mvneta.c index 38ad14eff9..fa20f548e5 100644 --- a/drivers/net/mvneta.c +++ b/drivers/net/mvneta.c @@ -2,7 +2,7 @@ * Driver for Marvell NETA network card for Armada XP and Armada 370 SoCs. * * U-Boot version: - * Copyright (C) 2014 Stefan Roese + * Copyright (C) 2014-2015 Stefan Roese * * Based on the Linux version which is: * Copyright (C) 2012 Marvell @@ -14,6 +14,7 @@ */ #include +#include #include #include #include @@ -28,6 +29,8 @@ #include #include +DECLARE_GLOBAL_DATA_PTR; + #if !defined(CONFIG_PHYLIB) # error Marvell mvneta requires PHYLIB #endif @@ -1115,9 +1118,9 @@ static void mvneta_start_dev(struct mvneta_port *pp) mvneta_port_enable(pp); } -static void mvneta_adjust_link(struct eth_device *dev) +static void mvneta_adjust_link(struct udevice *dev) { - struct mvneta_port *pp = dev->priv; + struct mvneta_port *pp = dev_get_priv(dev); struct phy_device *phydev = pp->phydev; int status_change = 0; @@ -1171,9 +1174,9 @@ static void mvneta_adjust_link(struct eth_device *dev) } } -static int mvneta_open(struct eth_device *dev) +static int mvneta_open(struct udevice *dev) { - struct mvneta_port *pp = dev->priv; + struct mvneta_port *pp = dev_get_priv(dev); int ret; ret = mvneta_setup_rxqs(pp); @@ -1192,7 +1195,7 @@ static int mvneta_open(struct eth_device *dev) } /* Initialize hw */ -static int mvneta_init(struct mvneta_port *pp) +static int mvneta_init2(struct mvneta_port *pp) { int queue; @@ -1314,23 +1317,22 @@ static int mvneta_port_power_up(struct mvneta_port *pp, int phy_mode) } /* Device initialization routine */ -static int mvneta_probe(struct eth_device *dev) +static int mvneta_init(struct udevice *dev) { - struct mvneta_port *pp = dev->priv; + struct eth_pdata *pdata = dev_get_platdata(dev); + struct mvneta_port *pp = dev_get_priv(dev); int err; pp->tx_ring_size = MVNETA_MAX_TXD; pp->rx_ring_size = MVNETA_MAX_RXD; - err = mvneta_init(pp); + err = mvneta_init2(pp); if (err < 0) { dev_err(&pdev->dev, "can't init eth hal\n"); return err; } - mvneta_conf_mbus_windows(pp); - - mvneta_mac_addr_set(pp, dev->enetaddr, rxq_def); + mvneta_mac_addr_set(pp, pdata->enetaddr, rxq_def); err = mvneta_port_power_up(pp, pp->phy_interface); if (err < 0) { @@ -1367,25 +1369,24 @@ static int smi_wait_ready(struct mvneta_port *pp) } /* - * smi_reg_read - miiphy_read callback function. + * mvneta_mdio_read - miiphy_read callback function. * * Returns 16bit phy register value, or 0xffff on error */ -static int smi_reg_read(const char *devname, u8 phy_adr, u8 reg_ofs, u16 *data) +static int mvneta_mdio_read(struct mii_dev *bus, int addr, int devad, int reg) { - struct eth_device *dev = eth_get_dev_by_name(devname); - struct mvneta_port *pp = dev->priv; + struct mvneta_port *pp = bus->priv; u32 smi_reg; u32 timeout; /* check parameters */ - if (phy_adr > MVNETA_PHY_ADDR_MASK) { - printf("Error: Invalid PHY address %d\n", phy_adr); + if (addr > MVNETA_PHY_ADDR_MASK) { + printf("Error: Invalid PHY address %d\n", addr); return -EFAULT; } - if (reg_ofs > MVNETA_PHY_REG_MASK) { - printf("Err: Invalid register offset %d\n", reg_ofs); + if (reg > MVNETA_PHY_REG_MASK) { + printf("Err: Invalid register offset %d\n", reg); return -EFAULT; } @@ -1394,14 +1395,14 @@ static int smi_reg_read(const char *devname, u8 phy_adr, u8 reg_ofs, u16 *data) return -EFAULT; /* fill the phy address and regiser offset and read opcode */ - smi_reg = (phy_adr << MVNETA_SMI_DEV_ADDR_OFFS) - | (reg_ofs << MVNETA_SMI_REG_ADDR_OFFS) + smi_reg = (addr << MVNETA_SMI_DEV_ADDR_OFFS) + | (reg << MVNETA_SMI_REG_ADDR_OFFS) | MVNETA_SMI_OPCODE_READ; /* write the smi register */ mvreg_write(pp, MVNETA_SMI, smi_reg); - /*wait till read value is ready */ + /* wait till read value is ready */ timeout = MVNETA_SMI_TIMEOUT; do { @@ -1417,31 +1418,29 @@ static int smi_reg_read(const char *devname, u8 phy_adr, u8 reg_ofs, u16 *data) for (timeout = 0; timeout < MVNETA_SMI_TIMEOUT; timeout++) ; - *data = (u16)(mvreg_read(pp, MVNETA_SMI) & MVNETA_SMI_DATA_MASK); - - return 0; + return mvreg_read(pp, MVNETA_SMI) & MVNETA_SMI_DATA_MASK; } /* - * smi_reg_write - imiiphy_write callback function. + * mvneta_mdio_write - miiphy_write callback function. * * Returns 0 if write succeed, -EINVAL on bad parameters * -ETIME on timeout */ -static int smi_reg_write(const char *devname, u8 phy_adr, u8 reg_ofs, u16 data) +static int mvneta_mdio_write(struct mii_dev *bus, int addr, int devad, int reg, + u16 value) { - struct eth_device *dev = eth_get_dev_by_name(devname); - struct mvneta_port *pp = dev->priv; + struct mvneta_port *pp = bus->priv; u32 smi_reg; /* check parameters */ - if (phy_adr > MVNETA_PHY_ADDR_MASK) { - printf("Error: Invalid PHY address %d\n", phy_adr); + if (addr > MVNETA_PHY_ADDR_MASK) { + printf("Error: Invalid PHY address %d\n", addr); return -EFAULT; } - if (reg_ofs > MVNETA_PHY_REG_MASK) { - printf("Err: Invalid register offset %d\n", reg_ofs); + if (reg > MVNETA_PHY_REG_MASK) { + printf("Err: Invalid register offset %d\n", reg); return -EFAULT; } @@ -1450,9 +1449,9 @@ static int smi_reg_write(const char *devname, u8 phy_adr, u8 reg_ofs, u16 data) return -EFAULT; /* fill the phy addr and reg offset and write opcode and data */ - smi_reg = (data << MVNETA_SMI_DATA_OFFS); - smi_reg |= (phy_adr << MVNETA_SMI_DEV_ADDR_OFFS) - | (reg_ofs << MVNETA_SMI_REG_ADDR_OFFS); + smi_reg = value << MVNETA_SMI_DATA_OFFS; + smi_reg |= (addr << MVNETA_SMI_DEV_ADDR_OFFS) + | (reg << MVNETA_SMI_REG_ADDR_OFFS); smi_reg &= ~MVNETA_SMI_OPCODE_READ; /* write the smi register */ @@ -1461,9 +1460,9 @@ static int smi_reg_write(const char *devname, u8 phy_adr, u8 reg_ofs, u16 data) return 0; } -static int mvneta_init_u_boot(struct eth_device *dev, bd_t *bis) +static int mvneta_start(struct udevice *dev) { - struct mvneta_port *pp = dev->priv; + struct mvneta_port *pp = dev_get_priv(dev); struct phy_device *phydev; mvneta_port_power_up(pp, pp->phy_interface); @@ -1483,7 +1482,7 @@ static int mvneta_init_u_boot(struct eth_device *dev, bd_t *bis) } /* Full init on first call */ - mvneta_probe(dev); + mvneta_init(dev); pp->init = 1; } else { /* Upon all following calls, this is enough */ @@ -1494,9 +1493,9 @@ static int mvneta_init_u_boot(struct eth_device *dev, bd_t *bis) return 0; } -static int mvneta_send(struct eth_device *dev, void *ptr, int len) +static int mvneta_send(struct udevice *dev, void *packet, int length) { - struct mvneta_port *pp = dev->priv; + struct mvneta_port *pp = dev_get_priv(dev); struct mvneta_tx_queue *txq = &pp->txqs[0]; struct mvneta_tx_desc *tx_desc; int sent_desc; @@ -1505,9 +1504,9 @@ static int mvneta_send(struct eth_device *dev, void *ptr, int len) /* Get a descriptor for the first part of the packet */ tx_desc = mvneta_txq_next_desc_get(txq); - tx_desc->buf_phys_addr = (u32)ptr; - tx_desc->data_size = len; - flush_dcache_range((u32)ptr, (u32)ptr + len); + tx_desc->buf_phys_addr = (u32)packet; + tx_desc->data_size = length; + flush_dcache_range((u32)packet, (u32)packet + length); /* First and Last descriptor */ tx_desc->command = MVNETA_TX_L4_CSUM_NOT | MVNETA_TXD_FLZ_DESC; @@ -1525,28 +1524,25 @@ static int mvneta_send(struct eth_device *dev, void *ptr, int len) /* txDone has increased - hw sent packet */ mvneta_txq_sent_desc_dec(pp, txq, sent_desc); - return 0; return 0; } -static int mvneta_recv(struct eth_device *dev) +static int mvneta_recv(struct udevice *dev, int flags, uchar **packetp) { - struct mvneta_port *pp = dev->priv; + struct mvneta_port *pp = dev_get_priv(dev); int rx_done; - int packets_done; struct mvneta_rx_queue *rxq; + int rx_bytes = 0; /* get rx queue */ rxq = mvneta_rxq_handle_get(pp, rxq_def); rx_done = mvneta_rxq_busy_desc_num_get(pp, rxq); - packets_done = rx_done; - while (packets_done--) { + if (rx_done) { struct mvneta_rx_desc *rx_desc; unsigned char *data; u32 rx_status; - int rx_bytes; /* * No cache invalidation needed here, since the desc's are @@ -1559,7 +1555,7 @@ static int mvneta_recv(struct eth_device *dev) (rx_status & MVNETA_RXD_ERR_SUMMARY)) { mvneta_rx_error(pp, rx_desc); /* leave the descriptor untouched */ - continue; + return -EIO; } /* 2 bytes for marvell header. 4 bytes for crc */ @@ -1571,40 +1567,24 @@ static int mvneta_recv(struct eth_device *dev) * No cache invalidation needed here, since the rx_buffer's are * located in a uncached memory region */ - net_process_received_packet(data, rx_bytes); - } + *packetp = data; - /* Update rxq management counters */ - if (rx_done) mvneta_rxq_desc_num_update(pp, rxq, rx_done, rx_done); + } - return 0; -} - -static void mvneta_halt(struct eth_device *dev) -{ - struct mvneta_port *pp = dev->priv; - - mvneta_port_down(pp); - mvneta_port_disable(pp); + return rx_bytes; } -int mvneta_initialize(bd_t *bis, int base_addr, int devnum, int phy_addr) +static int mvneta_probe(struct udevice *dev) { - struct eth_device *dev; - struct mvneta_port *pp; + struct eth_pdata *pdata = dev_get_platdata(dev); + struct mvneta_port *pp = dev_get_priv(dev); + void *blob = (void *)gd->fdt_blob; + int node = dev->of_offset; + struct mii_dev *bus; + unsigned long addr; void *bd_space; - dev = calloc(1, sizeof(*dev)); - if (dev == NULL) - return -ENOMEM; - - pp = calloc(1, sizeof(*pp)); - if (pp == NULL) - return -ENOMEM; - - dev->priv = pp; - /* * Allocate buffer area for descs and rx_buffers. This is only * done once for all interfaces. As only one interface can @@ -1625,28 +1605,82 @@ int mvneta_initialize(bd_t *bis, int base_addr, int devnum, int phy_addr) MVNETA_MAX_RXD * sizeof(struct mvneta_rx_desc)); } - sprintf(dev->name, "neta%d", devnum); + pp->base = (void __iomem *)pdata->iobase; - pp->base = (void __iomem *)base_addr; - dev->iobase = base_addr; - dev->init = mvneta_init_u_boot; - dev->halt = mvneta_halt; - dev->send = mvneta_send; - dev->recv = mvneta_recv; - dev->write_hwaddr = NULL; + /* Configure MBUS address windows */ + mvneta_conf_mbus_windows(pp); - /* - * The PHY interface type is configured via the - * board specific CONFIG_SYS_NETA_INTERFACE_TYPE - * define. - */ - pp->phy_interface = CONFIG_SYS_NETA_INTERFACE_TYPE; + /* PHY interface is already decoded in mvneta_ofdata_to_platdata() */ + pp->phy_interface = pdata->phy_interface; + + /* Now read phyaddr from DT */ + addr = fdtdec_get_int(blob, node, "phy", 0); + addr = fdt_node_offset_by_phandle(blob, addr); + pp->phyaddr = fdtdec_get_int(blob, addr, "reg", 0); + + bus = mdio_alloc(); + if (!bus) { + printf("Failed to allocate MDIO bus\n"); + return -ENOMEM; + } + + bus->read = mvneta_mdio_read; + bus->write = mvneta_mdio_write; + snprintf(bus->name, sizeof(bus->name), dev->name); + bus->priv = (void *)pp; + pp->bus = bus; - eth_register(dev); + return mdio_register(bus); +} - pp->phyaddr = phy_addr; - miiphy_register(dev->name, smi_reg_read, smi_reg_write); - pp->bus = miiphy_get_dev_by_name(dev->name); +static void mvneta_stop(struct udevice *dev) +{ + struct mvneta_port *pp = dev_get_priv(dev); - return 1; + mvneta_port_down(pp); + mvneta_port_disable(pp); } + +static const struct eth_ops mvneta_ops = { + .start = mvneta_start, + .send = mvneta_send, + .recv = mvneta_recv, + .stop = mvneta_stop, +}; + +static int mvneta_ofdata_to_platdata(struct udevice *dev) +{ + struct eth_pdata *pdata = dev_get_platdata(dev); + const char *phy_mode; + + pdata->iobase = dev_get_addr(dev); + + /* Get phy-mode / phy_interface from DT */ + pdata->phy_interface = -1; + phy_mode = fdt_getprop(gd->fdt_blob, dev->of_offset, "phy-mode", NULL); + if (phy_mode) + pdata->phy_interface = phy_get_interface_by_name(phy_mode); + if (pdata->phy_interface == -1) { + debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode); + return -EINVAL; + } + + return 0; +} + +static const struct udevice_id mvneta_ids[] = { + { .compatible = "marvell,armada-370-neta" }, + { .compatible = "marvell,armada-xp-neta" }, + { } +}; + +U_BOOT_DRIVER(mvneta) = { + .name = "mvneta", + .id = UCLASS_ETH, + .of_match = mvneta_ids, + .ofdata_to_platdata = mvneta_ofdata_to_platdata, + .probe = mvneta_probe, + .ops = &mvneta_ops, + .priv_auto_alloc_size = sizeof(struct mvneta_port), + .platdata_auto_alloc_size = sizeof(struct eth_pdata), +}; diff --git a/include/configs/db-88f6820-gp.h b/include/configs/db-88f6820-gp.h index 55ba7d30a6..a6ecba3bd1 100644 --- a/include/configs/db-88f6820-gp.h +++ b/include/configs/db-88f6820-gp.h @@ -99,8 +99,6 @@ #define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */ #define CONFIG_PHY_MARVELL /* there is a marvell phy */ -#define CONFIG_PHY_ADDR { 1, 0 } -#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII #define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ /* PCIe support */ @@ -109,7 +107,6 @@ #define CONFIG_PCI_MVEBU #define CONFIG_PCI_PNP #define CONFIG_PCI_SCAN_SHOW -#define CONFIG_E1000 /* enable Intel E1000 support for testing */ #endif #define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */ diff --git a/include/configs/db-mv784mp-gp.h b/include/configs/db-mv784mp-gp.h index d0f9f897b3..6c3f444743 100644 --- a/include/configs/db-mv784mp-gp.h +++ b/include/configs/db-mv784mp-gp.h @@ -64,10 +64,7 @@ #define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */ #define CONFIG_PHY_MARVELL /* there is a marvell phy */ -#define CONFIG_PHY_ADDR { 0x10, 0x11, 0x12, 0x13 } -#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_QSGMII #define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ -#define CONFIG_RESET_PHY_R #define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */ #define CONFIG_SYS_ALT_MEMTEST @@ -106,7 +103,6 @@ #define CONFIG_PCI_MVEBU #define CONFIG_PCI_PNP #define CONFIG_PCI_SCAN_SHOW -#define CONFIG_E1000 /* enable Intel E1000 support for testing */ #endif /* NAND */ diff --git a/include/configs/maxbcm.h b/include/configs/maxbcm.h index 682ce765f7..ada5267d34 100644 --- a/include/configs/maxbcm.h +++ b/include/configs/maxbcm.h @@ -55,10 +55,7 @@ #define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */ #define CONFIG_PHY_MARVELL /* there is a marvell phy */ -#define CONFIG_PHY_ADDR { 0x0, 0x1, 0x2, 0x3 } -#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII #define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ -#define CONFIG_RESET_PHY_R #define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */ #define CONFIG_SYS_ALT_MEMTEST