From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Date: Fri, 25 Jun 2021 11:19:11 +0000 (+0900)
Subject: serial: zynq: Add support for serial parameters
X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=da1af52f751993cc34abf423497f48c713d633a2;p=u-boot.git

serial: zynq: Add support for serial parameters

This adds serial parameters that include stop bit mode, parity mode,
and character length. Mark parity and space parity modes are not
supported.

At the moment, the only path to call setconfig directly is DM testing,
however, this affects the size of SPL for DM testing, so it doesn't
apply to SPL.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---

diff --git a/drivers/serial/serial_zynq.c b/drivers/serial/serial_zynq.c
index 799d524047..2f49f594a4 100644
--- a/drivers/serial/serial_zynq.c
+++ b/drivers/serial/serial_zynq.c
@@ -28,7 +28,17 @@
 #define ZYNQ_UART_CR_TXRST	BIT(1) /* TX logic reset */
 #define ZYNQ_UART_CR_RXRST	BIT(0) /* RX logic reset */
 
+#define ZYNQ_UART_MR_STOPMODE_2_BIT	0x00000080  /* 2 stop bits */
+#define ZYNQ_UART_MR_STOPMODE_1_5_BIT	0x00000040  /* 1.5 stop bits */
+#define ZYNQ_UART_MR_STOPMODE_1_BIT	0x00000000  /* 1 stop bit */
+
 #define ZYNQ_UART_MR_PARITY_NONE	0x00000020  /* No parity mode */
+#define ZYNQ_UART_MR_PARITY_ODD		0x00000008  /* Odd parity mode */
+#define ZYNQ_UART_MR_PARITY_EVEN	0x00000000  /* Even parity mode */
+
+#define ZYNQ_UART_MR_CHARLEN_6_BIT	0x00000006  /* 6 bits data */
+#define ZYNQ_UART_MR_CHARLEN_7_BIT	0x00000004  /* 7 bits data */
+#define ZYNQ_UART_MR_CHARLEN_8_BIT	0x00000000  /* 8 bits data */
 
 struct uart_zynq {
 	u32 control; /* 0x0 - Control Register [8:0] */
@@ -137,6 +147,63 @@ static int zynq_serial_setbrg(struct udevice *dev, int baudrate)
 	return 0;
 }
 
+#if !defined(CONFIG_SPL_BUILD)
+static int zynq_serial_setconfig(struct udevice *dev, uint serial_config)
+{
+	struct zynq_uart_plat *plat = dev_get_plat(dev);
+	struct uart_zynq *regs = plat->regs;
+	u32 val = 0;
+
+	switch (SERIAL_GET_BITS(serial_config)) {
+	case SERIAL_6_BITS:
+		val |= ZYNQ_UART_MR_CHARLEN_6_BIT;
+		break;
+	case SERIAL_7_BITS:
+		val |= ZYNQ_UART_MR_CHARLEN_7_BIT;
+		break;
+	case SERIAL_8_BITS:
+		val |= ZYNQ_UART_MR_CHARLEN_8_BIT;
+		break;
+	default:
+		return -ENOTSUPP; /* not supported in driver */
+	}
+
+	switch (SERIAL_GET_STOP(serial_config)) {
+	case SERIAL_ONE_STOP:
+		val |= ZYNQ_UART_MR_STOPMODE_1_BIT;
+		break;
+	case SERIAL_ONE_HALF_STOP:
+		val |= ZYNQ_UART_MR_STOPMODE_1_5_BIT;
+		break;
+	case SERIAL_TWO_STOP:
+		val |= ZYNQ_UART_MR_STOPMODE_2_BIT;
+		break;
+	default:
+		return -ENOTSUPP; /* not supported in driver */
+	}
+
+	switch (SERIAL_GET_PARITY(serial_config)) {
+	case SERIAL_PAR_NONE:
+		val |= ZYNQ_UART_MR_PARITY_NONE;
+		break;
+	case SERIAL_PAR_ODD:
+		val |= ZYNQ_UART_MR_PARITY_ODD;
+		break;
+	case SERIAL_PAR_EVEN:
+		val |= ZYNQ_UART_MR_PARITY_EVEN;
+		break;
+	default:
+		return -ENOTSUPP; /* not supported in driver */
+	}
+
+	writel(val, &regs->mode);
+
+	return 0;
+}
+#else
+#define zynq_serial_setconfig NULL
+#endif
+
 static int zynq_serial_probe(struct udevice *dev)
 {
 	struct zynq_uart_plat *plat = dev_get_plat(dev);
@@ -198,6 +265,7 @@ static const struct dm_serial_ops zynq_serial_ops = {
 	.pending = zynq_serial_pending,
 	.getc = zynq_serial_getc,
 	.setbrg = zynq_serial_setbrg,
+	.setconfig = zynq_serial_setconfig,
 };
 
 static const struct udevice_id zynq_serial_ids[] = {