From: Fabio Estevam Date: Thu, 18 Jun 2020 23:21:20 +0000 (-0300) Subject: mx6cuboxi: Convert to DM_ETH X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=d8da22c5dbdc7bc61b575278ea0e02919ffbe734;p=u-boot.git mx6cuboxi: Convert to DM_ETH Migration to DM_ETH is mandatory, so convert mx6cuboxi to Ethernet Driver Model. This also brings the benefit of restoring Ethernet functionality. Reported-by: Tom Rini Signed-off-by: Fabio Estevam Tested-by: Tom Rini --- diff --git a/board/solidrun/mx6cuboxi/mx6cuboxi.c b/board/solidrun/mx6cuboxi/mx6cuboxi.c index 94707bccb2..59e8b1dca1 100644 --- a/board/solidrun/mx6cuboxi/mx6cuboxi.c +++ b/board/solidrun/mx6cuboxi/mx6cuboxi.c @@ -17,7 +17,6 @@ #include #include #include -#include #include #include #include @@ -33,8 +32,6 @@ #include #include #include -#include -#include #include #include #include @@ -52,16 +49,6 @@ DECLARE_GLOBAL_DATA_PTR; PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ PAD_CTL_SRE_FAST | PAD_CTL_HYS) -#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) - -#define ENET_PAD_CTRL_PD (PAD_CTL_PUS_100K_DOWN | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) - -#define ENET_PAD_CTRL_CLK ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) - -#define ETH_PHY_RESET IMX_GPIO_NR(4, 15) #define USB_H1_VBUS IMX_GPIO_NR(1, 0) enum board_type { @@ -237,110 +224,6 @@ int board_mmc_init(bd_t *bis) return 0; } -static iomux_v3_cfg_t const enet_pads[] = { - IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)), - /* AR8035 reset */ - IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)), - /* AR8035 interrupt */ - IOMUX_PADS(PAD_DI0_PIN2__GPIO4_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL)), - /* GPIO16 -> AR8035 25MHz */ - IOMUX_PADS(PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(NO_PAD_CTRL)), - IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(NO_PAD_CTRL)), - IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)), - /* AR8035 CLK_25M --> ENET_REF_CLK (V22) */ - IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK)), - IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)), - IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)), - IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)), - IOMUX_PADS(PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)), - IOMUX_PADS(PAD_ENET_RXD1__GPIO1_IO26 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)), -}; - -static void setup_iomux_enet(void) -{ - struct gpio_desc desc; - int ret; - - SETUP_IOMUX_PADS(enet_pads); - - ret = dm_gpio_lookup_name("GPIO4_15", &desc); - if (ret) { - printf("%s: phy reset lookup failed\n", __func__); - return; - } - - ret = dm_gpio_request(&desc, "phy-reset"); - if (ret) { - printf("%s: phy reset request failed\n", __func__); - return; - } - - gpio_direction_output(ETH_PHY_RESET, 0); - mdelay(10); - gpio_set_value(ETH_PHY_RESET, 1); - udelay(100); - - gpio_free_list_nodev(&desc, 1); -} - -int board_phy_config(struct phy_device *phydev) -{ - if (phydev->drv->config) - phydev->drv->config(phydev); - - return 0; -} - -/* On Cuboxi Ethernet PHY can be located at addresses 0x0 or 0x4 */ -#define ETH_PHY_MASK ((1 << 0x0) | (1 << 0x4)) - -int board_eth_init(bd_t *bis) -{ - struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; - struct mii_dev *bus; - struct phy_device *phydev; - - int ret = enable_fec_anatop_clock(0, ENET_25MHZ); - if (ret) - return ret; - - /* set gpr1[ENET_CLK_SEL] */ - setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK); - - setup_iomux_enet(); - - bus = fec_get_miibus(IMX_FEC_BASE, -1); - if (!bus) - return -EINVAL; - - phydev = phy_find_by_mask(bus, ETH_PHY_MASK, PHY_INTERFACE_MODE_RGMII); - if (!phydev) { - ret = -EINVAL; - goto free_bus; - } - - debug("using phy at address %d\n", phydev->addr); - ret = fec_probe(bis, -1, IMX_FEC_BASE, bus, phydev); - if (ret) - goto free_phydev; - - return 0; - -free_phydev: - free(phydev); -free_bus: - free(bus); - return ret; -} - #ifdef CONFIG_VIDEO_IPUV3 static void do_enable_hdmi(struct display_info_t const *dev) { @@ -433,6 +316,21 @@ static int setup_display(void) } #endif /* CONFIG_VIDEO_IPUV3 */ +static int setup_fec(void) +{ + struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; + int ret; + + ret = enable_fec_anatop_clock(0, ENET_25MHZ); + if (ret) + return ret; + + /* set gpr1[ENET_CLK_SEL] */ + setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK); + + return 0; +} + int board_early_init_f(void) { setup_iomux_uart(); @@ -440,6 +338,8 @@ int board_early_init_f(void) #ifdef CONFIG_CMD_SATA setup_sata(); #endif + setup_fec(); + return 0; } diff --git a/configs/mx6cuboxi_defconfig b/configs/mx6cuboxi_defconfig index df7e4611a0..568cfce4c0 100644 --- a/configs/mx6cuboxi_defconfig +++ b/configs/mx6cuboxi_defconfig @@ -50,6 +50,9 @@ CONFIG_DM_MMC=y CONFIG_FSL_USDHC=y CONFIG_PHYLIB=y CONFIG_PHY_ATHEROS=y +CONFIG_DM_ETH=y +CONFIG_FEC_MXC=y +CONFIG_RGMII=y CONFIG_MII=y CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX6=y diff --git a/include/configs/mx6cuboxi.h b/include/configs/mx6cuboxi.h index 2ccf44e573..96f79e6b58 100644 --- a/include/configs/mx6cuboxi.h +++ b/include/configs/mx6cuboxi.h @@ -29,12 +29,6 @@ #define CONFIG_LBA48 #endif -/* Ethernet Configuration */ -#define CONFIG_FEC_MXC -#define IMX_FEC_BASE ENET_BASE_ADDR -#define CONFIG_FEC_XCV_TYPE RGMII -#define CONFIG_FEC_MXC_PHYADDR 0 - /* Framebuffer */ #define CONFIG_VIDEO_BMP_RLE8 #define CONFIG_SPLASH_SCREEN