From: Tuomas Tynkkynen Date: Tue, 20 Mar 2018 00:02:28 +0000 (+0200) Subject: net: Drop CONFIG_ENC28J60 X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=d04791dfa5e14183148c4b966a392de7a9869a10;p=u-boot.git net: Drop CONFIG_ENC28J60 Last user of this driver went away in October 2014 in commit d58a9451e7339ed4 ("ppc/arm: zap EMK boards"). Signed-off-by: Tuomas Tynkkynen Acked-by: Joe Hershberger --- diff --git a/drivers/net/Makefile b/drivers/net/Makefile index 95cb7bb271..2687fbbdb2 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -23,7 +23,6 @@ obj-$(CONFIG_E1000_SPI) += e1000_spi.o obj-$(CONFIG_EEPRO100) += eepro100.o obj-$(CONFIG_SUN4I_EMAC) += sunxi_emac.o obj-$(CONFIG_SUN8I_EMAC) += sun8i_emac.o -obj-$(CONFIG_ENC28J60) += enc28j60.o obj-$(CONFIG_EP93XX) += ep93xx_eth.o obj-$(CONFIG_ETHOC) += ethoc.o obj-$(CONFIG_FEC_MXC) += fec_mxc.o diff --git a/drivers/net/enc28j60.c b/drivers/net/enc28j60.c deleted file mode 100644 index 588a84d7a9..0000000000 --- a/drivers/net/enc28j60.c +++ /dev/null @@ -1,959 +0,0 @@ -/* - * (C) Copyright 2010 - * Reinhard Meyer, EMK Elektronik, reinhard.meyer@emk-elektronik.de - * Martin Krause, Martin.Krause@tqs.de - * reworked original enc28j60.c - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include -#include "enc28j60.h" - -/* - * IMPORTANT: spi_claim_bus() and spi_release_bus() - * are called at begin and end of each of the following functions: - * enc_miiphy_read(), enc_miiphy_write(), enc_write_hwaddr(), - * enc_init(), enc_recv(), enc_send(), enc_halt() - * ALL other functions assume that the bus has already been claimed! - * Since net_process_received_packet() might call enc_send() in return, the bus - * must be released, net_process_received_packet() called and claimed again. - */ - -/* - * Controller memory layout. - * We only allow 1 frame for transmission and reserve the rest - * for reception to handle as many broadcast packets as possible. - * Also use the memory from 0x0000 for receiver buffer. See errata pt. 5 - * 0x0000 - 0x19ff 6656 bytes receive buffer - * 0x1a00 - 0x1fff 1536 bytes transmit buffer = - * control(1)+frame(1518)+status(7)+reserve(10). - */ -#define ENC_RX_BUF_START 0x0000 -#define ENC_RX_BUF_END 0x19ff -#define ENC_TX_BUF_START 0x1a00 -#define ENC_TX_BUF_END 0x1fff -#define ENC_MAX_FRM_LEN 1518 -#define RX_RESET_COUNTER 1000 - -/* - * For non data transfer functions, like phy read/write, set hwaddr, init - * we do not need a full, time consuming init including link ready wait. - * This enum helps to bring the chip through the minimum necessary inits. - */ -enum enc_initstate {none=0, setupdone, linkready}; -typedef struct enc_device { - struct eth_device *dev; /* back pointer */ - struct spi_slave *slave; - int rx_reset_counter; - u16 next_pointer; - u8 bank; /* current bank in enc28j60 */ - enum enc_initstate initstate; -} enc_dev_t; - -/* - * enc_bset: set bits in a common register - * enc_bclr: clear bits in a common register - * - * making the reg parameter u8 will give a compile time warning if the - * functions are called with a register not accessible in all Banks - */ -static void enc_bset(enc_dev_t *enc, const u8 reg, const u8 data) -{ - u8 dout[2]; - - dout[0] = CMD_BFS(reg); - dout[1] = data; - spi_xfer(enc->slave, 2 * 8, dout, NULL, - SPI_XFER_BEGIN | SPI_XFER_END); -} - -static void enc_bclr(enc_dev_t *enc, const u8 reg, const u8 data) -{ - u8 dout[2]; - - dout[0] = CMD_BFC(reg); - dout[1] = data; - spi_xfer(enc->slave, 2 * 8, dout, NULL, - SPI_XFER_BEGIN | SPI_XFER_END); -} - -/* - * high byte of the register contains bank number: - * 0: no bank switch necessary - * 1: switch to bank 0 - * 2: switch to bank 1 - * 3: switch to bank 2 - * 4: switch to bank 3 - */ -static void enc_set_bank(enc_dev_t *enc, const u16 reg) -{ - u8 newbank = reg >> 8; - - if (newbank == 0 || newbank == enc->bank) - return; - switch (newbank) { - case 1: - enc_bclr(enc, CTL_REG_ECON1, - ENC_ECON1_BSEL0 | ENC_ECON1_BSEL1); - break; - case 2: - enc_bset(enc, CTL_REG_ECON1, ENC_ECON1_BSEL0); - enc_bclr(enc, CTL_REG_ECON1, ENC_ECON1_BSEL1); - break; - case 3: - enc_bclr(enc, CTL_REG_ECON1, ENC_ECON1_BSEL0); - enc_bset(enc, CTL_REG_ECON1, ENC_ECON1_BSEL1); - break; - case 4: - enc_bset(enc, CTL_REG_ECON1, - ENC_ECON1_BSEL0 | ENC_ECON1_BSEL1); - break; - } - enc->bank = newbank; -} - -/* - * local functions to access SPI - * - * reg: register inside ENC28J60 - * data: 8/16 bits to write - * c: number of retries - * - * enc_r8: read 8 bits - * enc_r16: read 16 bits - * enc_w8: write 8 bits - * enc_w16: write 16 bits - * enc_w8_retry: write 8 bits, verify and retry - * enc_rbuf: read from ENC28J60 into buffer - * enc_wbuf: write from buffer into ENC28J60 - */ - -/* - * MAC and MII registers need a 3 byte SPI transfer to read, - * all other registers need a 2 byte SPI transfer. - */ -static int enc_reg2nbytes(const u16 reg) -{ - /* check if MAC or MII register */ - return ((reg >= CTL_REG_MACON1 && reg <= CTL_REG_MIRDH) || - (reg >= CTL_REG_MAADR1 && reg <= CTL_REG_MAADR4) || - (reg == CTL_REG_MISTAT)) ? 3 : 2; -} - -/* - * Read a byte register - */ -static u8 enc_r8(enc_dev_t *enc, const u16 reg) -{ - u8 dout[3]; - u8 din[3]; - int nbytes = enc_reg2nbytes(reg); - - enc_set_bank(enc, reg); - dout[0] = CMD_RCR(reg); - spi_xfer(enc->slave, nbytes * 8, dout, din, - SPI_XFER_BEGIN | SPI_XFER_END); - return din[nbytes-1]; -} - -/* - * Read a L/H register pair and return a word. - * Must be called with the L register's address. - */ -static u16 enc_r16(enc_dev_t *enc, const u16 reg) -{ - u8 dout[3]; - u8 din[3]; - u16 result; - int nbytes = enc_reg2nbytes(reg); - - enc_set_bank(enc, reg); - dout[0] = CMD_RCR(reg); - spi_xfer(enc->slave, nbytes * 8, dout, din, - SPI_XFER_BEGIN | SPI_XFER_END); - result = din[nbytes-1]; - dout[0]++; /* next register */ - spi_xfer(enc->slave, nbytes * 8, dout, din, - SPI_XFER_BEGIN | SPI_XFER_END); - result |= din[nbytes-1] << 8; - return result; -} - -/* - * Write a byte register - */ -static void enc_w8(enc_dev_t *enc, const u16 reg, const u8 data) -{ - u8 dout[2]; - - enc_set_bank(enc, reg); - dout[0] = CMD_WCR(reg); - dout[1] = data; - spi_xfer(enc->slave, 2 * 8, dout, NULL, - SPI_XFER_BEGIN | SPI_XFER_END); -} - -/* - * Write a L/H register pair. - * Must be called with the L register's address. - */ -static void enc_w16(enc_dev_t *enc, const u16 reg, const u16 data) -{ - u8 dout[2]; - - enc_set_bank(enc, reg); - dout[0] = CMD_WCR(reg); - dout[1] = data; - spi_xfer(enc->slave, 2 * 8, dout, NULL, - SPI_XFER_BEGIN | SPI_XFER_END); - dout[0]++; /* next register */ - dout[1] = data >> 8; - spi_xfer(enc->slave, 2 * 8, dout, NULL, - SPI_XFER_BEGIN | SPI_XFER_END); -} - -/* - * Write a byte register, verify and retry - */ -static void enc_w8_retry(enc_dev_t *enc, const u16 reg, const u8 data, const int c) -{ - u8 dout[2]; - u8 readback; - int i; - - enc_set_bank(enc, reg); - for (i = 0; i < c; i++) { - dout[0] = CMD_WCR(reg); - dout[1] = data; - spi_xfer(enc->slave, 2 * 8, dout, NULL, - SPI_XFER_BEGIN | SPI_XFER_END); - readback = enc_r8(enc, reg); - if (readback == data) - break; - /* wait 1ms */ - udelay(1000); - } - if (i == c) { - printf("%s: write reg 0x%03x failed\n", enc->dev->name, reg); - } -} - -/* - * Read ENC RAM into buffer - */ -static void enc_rbuf(enc_dev_t *enc, const u16 length, u8 *buf) -{ - u8 dout[1]; - - dout[0] = CMD_RBM; - spi_xfer(enc->slave, 8, dout, NULL, SPI_XFER_BEGIN); - spi_xfer(enc->slave, length * 8, NULL, buf, SPI_XFER_END); -#ifdef DEBUG - puts("Rx:\n"); - print_buffer(0, buf, 1, length, 0); -#endif -} - -/* - * Write buffer into ENC RAM - */ -static void enc_wbuf(enc_dev_t *enc, const u16 length, const u8 *buf, const u8 control) -{ - u8 dout[2]; - dout[0] = CMD_WBM; - dout[1] = control; - spi_xfer(enc->slave, 2 * 8, dout, NULL, SPI_XFER_BEGIN); - spi_xfer(enc->slave, length * 8, buf, NULL, SPI_XFER_END); -#ifdef DEBUG - puts("Tx:\n"); - print_buffer(0, buf, 1, length, 0); -#endif -} - -/* - * Try to claim the SPI bus. - * Print error message on failure. - */ -static int enc_claim_bus(enc_dev_t *enc) -{ - int rc = spi_claim_bus(enc->slave); - if (rc) - printf("%s: failed to claim SPI bus\n", enc->dev->name); - return rc; -} - -/* - * Release previously claimed SPI bus. - * This function is mainly for symmetry to enc_claim_bus(). - * Let the toolchain decide to inline it... - */ -static void enc_release_bus(enc_dev_t *enc) -{ - spi_release_bus(enc->slave); -} - -/* - * Read PHY register - */ -static u16 enc_phy_read(enc_dev_t *enc, const u8 addr) -{ - uint64_t etime; - u8 status; - - enc_w8(enc, CTL_REG_MIREGADR, addr); - enc_w8(enc, CTL_REG_MICMD, ENC_MICMD_MIIRD); - /* 1 second timeout - only happens on hardware problem */ - etime = get_ticks() + get_tbclk(); - /* poll MISTAT.BUSY bit until operation is complete */ - do - { - status = enc_r8(enc, CTL_REG_MISTAT); - } while (get_ticks() <= etime && (status & ENC_MISTAT_BUSY)); - if (status & ENC_MISTAT_BUSY) { - printf("%s: timeout reading phy\n", enc->dev->name); - return 0; - } - enc_w8(enc, CTL_REG_MICMD, 0); - return enc_r16(enc, CTL_REG_MIRDL); -} - -/* - * Write PHY register - */ -static void enc_phy_write(enc_dev_t *enc, const u8 addr, const u16 data) -{ - uint64_t etime; - u8 status; - - enc_w8(enc, CTL_REG_MIREGADR, addr); - enc_w16(enc, CTL_REG_MIWRL, data); - /* 1 second timeout - only happens on hardware problem */ - etime = get_ticks() + get_tbclk(); - /* poll MISTAT.BUSY bit until operation is complete */ - do - { - status = enc_r8(enc, CTL_REG_MISTAT); - } while (get_ticks() <= etime && (status & ENC_MISTAT_BUSY)); - if (status & ENC_MISTAT_BUSY) { - printf("%s: timeout writing phy\n", enc->dev->name); - return; - } -} - -/* - * Verify link status, wait if necessary - * - * Note: with a 10 MBit/s only PHY there is no autonegotiation possible, - * half/full duplex is a pure setup matter. For the time being, this driver - * will setup in half duplex mode only. - */ -static int enc_phy_link_wait(enc_dev_t *enc) -{ - u16 status; - int duplex; - uint64_t etime; - -#ifdef CONFIG_ENC_SILENTLINK - /* check if we have a link, then just return */ - status = enc_phy_read(enc, PHY_REG_PHSTAT1); - if (status & ENC_PHSTAT1_LLSTAT) - return 0; -#endif - - /* wait for link with 1 second timeout */ - etime = get_ticks() + get_tbclk(); - while (get_ticks() <= etime) { - status = enc_phy_read(enc, PHY_REG_PHSTAT1); - if (status & ENC_PHSTAT1_LLSTAT) { - /* now we have a link */ - status = enc_phy_read(enc, PHY_REG_PHSTAT2); - duplex = (status & ENC_PHSTAT2_DPXSTAT) ? 1 : 0; - printf("%s: link up, 10Mbps %s-duplex\n", - enc->dev->name, duplex ? "full" : "half"); - return 0; - } - udelay(1000); - } - - /* timeout occurred */ - printf("%s: link down\n", enc->dev->name); - return 1; -} - -/* - * This function resets the receiver only. - */ -static void enc_reset_rx(enc_dev_t *enc) -{ - u8 econ1; - - econ1 = enc_r8(enc, CTL_REG_ECON1); - if ((econ1 & ENC_ECON1_RXRST) == 0) { - enc_bset(enc, CTL_REG_ECON1, ENC_ECON1_RXRST); - enc->rx_reset_counter = RX_RESET_COUNTER; - } -} - -/* - * Reset receiver and reenable it. - */ -static void enc_reset_rx_call(enc_dev_t *enc) -{ - enc_bclr(enc, CTL_REG_ECON1, ENC_ECON1_RXRST); - enc_bset(enc, CTL_REG_ECON1, ENC_ECON1_RXEN); -} - -/* - * Copy a packet from the receive ring and forward it to - * the protocol stack. - */ -static void enc_receive(enc_dev_t *enc) -{ - u8 *packet = (u8 *)net_rx_packets[0]; - u16 pkt_len; - u16 copy_len; - u16 status; - u8 pkt_cnt = 0; - u16 rxbuf_rdpt; - u8 hbuf[6]; - - enc_w16(enc, CTL_REG_ERDPTL, enc->next_pointer); - do { - enc_rbuf(enc, 6, hbuf); - enc->next_pointer = hbuf[0] | (hbuf[1] << 8); - pkt_len = hbuf[2] | (hbuf[3] << 8); - status = hbuf[4] | (hbuf[5] << 8); - debug("next_pointer=$%04x pkt_len=%u status=$%04x\n", - enc->next_pointer, pkt_len, status); - if (pkt_len <= ENC_MAX_FRM_LEN) - copy_len = pkt_len; - else - copy_len = 0; - if ((status & (1L << 7)) == 0) /* check Received Ok bit */ - copy_len = 0; - /* check if next pointer is resonable */ - if (enc->next_pointer >= ENC_TX_BUF_START) - copy_len = 0; - if (copy_len > 0) { - enc_rbuf(enc, copy_len, packet); - } - /* advance read pointer to next pointer */ - enc_w16(enc, CTL_REG_ERDPTL, enc->next_pointer); - /* decrease packet counter */ - enc_bset(enc, CTL_REG_ECON2, ENC_ECON2_PKTDEC); - /* - * Only odd values should be written to ERXRDPTL, - * see errata B4 pt.13 - */ - rxbuf_rdpt = enc->next_pointer - 1; - if ((rxbuf_rdpt < enc_r16(enc, CTL_REG_ERXSTL)) || - (rxbuf_rdpt > enc_r16(enc, CTL_REG_ERXNDL))) { - enc_w16(enc, CTL_REG_ERXRDPTL, - enc_r16(enc, CTL_REG_ERXNDL)); - } else { - enc_w16(enc, CTL_REG_ERXRDPTL, rxbuf_rdpt); - } - /* read pktcnt */ - pkt_cnt = enc_r8(enc, CTL_REG_EPKTCNT); - if (copy_len == 0) { - (void)enc_r8(enc, CTL_REG_EIR); - enc_reset_rx(enc); - printf("%s: receive copy_len=0\n", enc->dev->name); - continue; - } - /* - * Because net_process_received_packet() might call enc_send(), - * we need to release the SPI bus, call - * net_process_received_packet(), reclaim the bus. - */ - enc_release_bus(enc); - net_process_received_packet(packet, pkt_len); - if (enc_claim_bus(enc)) - return; - (void)enc_r8(enc, CTL_REG_EIR); - } while (pkt_cnt); - /* Use EPKTCNT not EIR.PKTIF flag, see errata pt. 6 */ -} - -/* - * Poll for completely received packets. - */ -static void enc_poll(enc_dev_t *enc) -{ - u8 eir_reg; - u8 pkt_cnt; - - (void)enc_r8(enc, CTL_REG_ESTAT); - eir_reg = enc_r8(enc, CTL_REG_EIR); - if (eir_reg & ENC_EIR_TXIF) { - /* clear TXIF bit in EIR */ - enc_bclr(enc, CTL_REG_EIR, ENC_EIR_TXIF); - } - /* We have to use pktcnt and not pktif bit, see errata pt. 6 */ - pkt_cnt = enc_r8(enc, CTL_REG_EPKTCNT); - if (pkt_cnt > 0) { - if ((eir_reg & ENC_EIR_PKTIF) == 0) { - debug("enc_poll: pkt cnt > 0, but pktif not set\n"); - } - enc_receive(enc); - /* - * clear PKTIF bit in EIR, this should not need to be done - * but it seems like we get problems if we do not - */ - enc_bclr(enc, CTL_REG_EIR, ENC_EIR_PKTIF); - } - if (eir_reg & ENC_EIR_RXERIF) { - printf("%s: rx error\n", enc->dev->name); - enc_bclr(enc, CTL_REG_EIR, ENC_EIR_RXERIF); - } - if (eir_reg & ENC_EIR_TXERIF) { - printf("%s: tx error\n", enc->dev->name); - enc_bclr(enc, CTL_REG_EIR, ENC_EIR_TXERIF); - } -} - -/* - * Completely Reset the ENC - */ -static void enc_reset(enc_dev_t *enc) -{ - u8 dout[1]; - - dout[0] = CMD_SRC; - spi_xfer(enc->slave, 8, dout, NULL, - SPI_XFER_BEGIN | SPI_XFER_END); - /* sleep 1 ms. See errata pt. 2 */ - udelay(1000); -} - -/* - * Initialisation data for most of the ENC registers - */ -static const u16 enc_initdata[] = { - /* - * Setup the buffer space. The reset values are valid for the - * other pointers. - * - * We shall not write to ERXST, see errata pt. 5. Instead we - * have to make sure that ENC_RX_BUS_START is 0. - */ - CTL_REG_ERXSTL, ENC_RX_BUF_START, - CTL_REG_ERXSTH, ENC_RX_BUF_START >> 8, - CTL_REG_ERXNDL, ENC_RX_BUF_END, - CTL_REG_ERXNDH, ENC_RX_BUF_END >> 8, - CTL_REG_ERDPTL, ENC_RX_BUF_START, - CTL_REG_ERDPTH, ENC_RX_BUF_START >> 8, - /* - * Set the filter to receive only good-CRC, unicast and broadcast - * frames. - * Note: some DHCP servers return their answers as broadcasts! - * So its unwise to remove broadcast from this. This driver - * might incur receiver overruns with packet loss on a broadcast - * flooded network. - */ - CTL_REG_ERXFCON, ENC_RFR_BCEN | ENC_RFR_UCEN | ENC_RFR_CRCEN, - - /* enable MAC to receive frames */ - CTL_REG_MACON1, - ENC_MACON1_MARXEN | ENC_MACON1_TXPAUS | ENC_MACON1_RXPAUS, - - /* configure pad, tx-crc and duplex */ - CTL_REG_MACON3, - ENC_MACON3_PADCFG0 | ENC_MACON3_TXCRCEN | - ENC_MACON3_FRMLNEN, - - /* Allow infinite deferals if the medium is continously busy */ - CTL_REG_MACON4, ENC_MACON4_DEFER, - - /* Late collisions occur beyond 63 bytes */ - CTL_REG_MACLCON2, 63, - - /* - * Set (low byte) Non-Back-to_Back Inter-Packet Gap. - * Recommended 0x12 - */ - CTL_REG_MAIPGL, 0x12, - - /* - * Set (high byte) Non-Back-to_Back Inter-Packet Gap. - * Recommended 0x0c for half-duplex. Nothing for full-duplex - */ - CTL_REG_MAIPGH, 0x0C, - - /* set maximum frame length */ - CTL_REG_MAMXFLL, ENC_MAX_FRM_LEN, - CTL_REG_MAMXFLH, ENC_MAX_FRM_LEN >> 8, - - /* - * Set MAC back-to-back inter-packet gap. - * Recommended 0x12 for half duplex - * and 0x15 for full duplex. - */ - CTL_REG_MABBIPG, 0x12, - - /* end of table */ - 0xffff -}; - -/* - * Wait for the XTAL oscillator to become ready - */ -static int enc_clock_wait(enc_dev_t *enc) -{ - uint64_t etime; - - /* one second timeout */ - etime = get_ticks() + get_tbclk(); - - /* - * Wait for CLKRDY to become set (i.e., check that we can - * communicate with the ENC) - */ - do - { - if (enc_r8(enc, CTL_REG_ESTAT) & ENC_ESTAT_CLKRDY) - return 0; - } while (get_ticks() <= etime); - - printf("%s: timeout waiting for CLKRDY\n", enc->dev->name); - return -1; -} - -/* - * Write the MAC address into the ENC - */ -static int enc_write_macaddr(enc_dev_t *enc) -{ - unsigned char *p = enc->dev->enetaddr; - - enc_w8_retry(enc, CTL_REG_MAADR5, *p++, 5); - enc_w8_retry(enc, CTL_REG_MAADR4, *p++, 5); - enc_w8_retry(enc, CTL_REG_MAADR3, *p++, 5); - enc_w8_retry(enc, CTL_REG_MAADR2, *p++, 5); - enc_w8_retry(enc, CTL_REG_MAADR1, *p++, 5); - enc_w8_retry(enc, CTL_REG_MAADR0, *p, 5); - return 0; -} - -/* - * Setup most of the ENC registers - */ -static int enc_setup(enc_dev_t *enc) -{ - u16 phid1 = 0; - u16 phid2 = 0; - const u16 *tp; - - /* reset enc struct values */ - enc->next_pointer = ENC_RX_BUF_START; - enc->rx_reset_counter = RX_RESET_COUNTER; - enc->bank = 0xff; /* invalidate current bank in enc28j60 */ - - /* verify PHY identification */ - phid1 = enc_phy_read(enc, PHY_REG_PHID1); - phid2 = enc_phy_read(enc, PHY_REG_PHID2) & ENC_PHID2_MASK; - if (phid1 != ENC_PHID1_VALUE || phid2 != ENC_PHID2_VALUE) { - printf("%s: failed to identify PHY. Found %04x:%04x\n", - enc->dev->name, phid1, phid2); - return -1; - } - - /* now program registers */ - for (tp = enc_initdata; *tp != 0xffff; tp += 2) - enc_w8_retry(enc, tp[0], tp[1], 10); - - /* - * Prevent automatic loopback of data beeing transmitted by setting - * ENC_PHCON2_HDLDIS - */ - enc_phy_write(enc, PHY_REG_PHCON2, (1<<8)); - - /* - * LEDs configuration - * LEDA: LACFG = 0100 -> display link status - * LEDB: LBCFG = 0111 -> display TX & RX activity - * STRCH = 1 -> LED pulses - */ - enc_phy_write(enc, PHY_REG_PHLCON, 0x0472); - - /* Reset PDPXMD-bit => half duplex */ - enc_phy_write(enc, PHY_REG_PHCON1, 0); - - return 0; -} - -/* - * Check if ENC has been initialized. - * If not, try to initialize it. - * Remember initialized state in struct. - */ -static int enc_initcheck(enc_dev_t *enc, const enum enc_initstate requiredstate) -{ - if (enc->initstate >= requiredstate) - return 0; - - if (enc->initstate < setupdone) { - /* Initialize the ENC only */ - enc_reset(enc); - /* if any of functions fails, skip the rest and return an error */ - if (enc_clock_wait(enc) || enc_setup(enc) || enc_write_macaddr(enc)) { - return -1; - } - enc->initstate = setupdone; - } - /* if that's all we need, return here */ - if (enc->initstate >= requiredstate) - return 0; - - /* now wait for link ready condition */ - if (enc_phy_link_wait(enc)) { - return -1; - } - enc->initstate = linkready; - return 0; -} - -#if defined(CONFIG_CMD_MII) -/* - * Read a PHY register. - * - * This function is registered with miiphy_register(). - */ -int enc_miiphy_read(struct mii_dev *bus, int phy_adr, int devad, int reg) -{ - u16 value = 0; - struct eth_device *dev = eth_get_dev_by_name(bus->name); - enc_dev_t *enc; - - if (!dev || phy_adr != 0) - return -1; - - enc = dev->priv; - if (enc_claim_bus(enc)) - return -1; - if (enc_initcheck(enc, setupdone)) { - enc_release_bus(enc); - return -1; - } - value = enc_phy_read(enc, reg); - enc_release_bus(enc); - return value; -} - -/* - * Write a PHY register. - * - * This function is registered with miiphy_register(). - */ -int enc_miiphy_write(struct mii_dev *bus, int phy_adr, int devad, int reg, - u16 value) -{ - struct eth_device *dev = eth_get_dev_by_name(bus->name); - enc_dev_t *enc; - - if (!dev || phy_adr != 0) - return -1; - - enc = dev->priv; - if (enc_claim_bus(enc)) - return -1; - if (enc_initcheck(enc, setupdone)) { - enc_release_bus(enc); - return -1; - } - enc_phy_write(enc, reg, value); - enc_release_bus(enc); - return 0; -} -#endif - -/* - * Write hardware (MAC) address. - * - * This function entered into eth_device structure. - */ -static int enc_write_hwaddr(struct eth_device *dev) -{ - enc_dev_t *enc = dev->priv; - - if (enc_claim_bus(enc)) - return -1; - if (enc_initcheck(enc, setupdone)) { - enc_release_bus(enc); - return -1; - } - enc_release_bus(enc); - return 0; -} - -/* - * Initialize ENC28J60 for use. - * - * This function entered into eth_device structure. - */ -static int enc_init(struct eth_device *dev, bd_t *bis) -{ - enc_dev_t *enc = dev->priv; - - if (enc_claim_bus(enc)) - return -1; - if (enc_initcheck(enc, linkready)) { - enc_release_bus(enc); - return -1; - } - /* enable receive */ - enc_bset(enc, CTL_REG_ECON1, ENC_ECON1_RXEN); - enc_release_bus(enc); - return 0; -} - -/* - * Check for received packets. - * - * This function entered into eth_device structure. - */ -static int enc_recv(struct eth_device *dev) -{ - enc_dev_t *enc = dev->priv; - - if (enc_claim_bus(enc)) - return -1; - if (enc_initcheck(enc, linkready)) { - enc_release_bus(enc); - return -1; - } - /* Check for dead receiver */ - if (enc->rx_reset_counter > 0) - enc->rx_reset_counter--; - else - enc_reset_rx_call(enc); - enc_poll(enc); - enc_release_bus(enc); - return 0; -} - -/* - * Send a packet. - * - * This function entered into eth_device structure. - * - * Should we wait here until we have a Link? Or shall we leave that to - * protocol retries? - */ -static int enc_send( - struct eth_device *dev, - void *packet, - int length) -{ - enc_dev_t *enc = dev->priv; - - if (enc_claim_bus(enc)) - return -1; - if (enc_initcheck(enc, linkready)) { - enc_release_bus(enc); - return -1; - } - /* setup transmit pointers */ - enc_w16(enc, CTL_REG_EWRPTL, ENC_TX_BUF_START); - enc_w16(enc, CTL_REG_ETXNDL, length + ENC_TX_BUF_START); - enc_w16(enc, CTL_REG_ETXSTL, ENC_TX_BUF_START); - /* write packet to ENC */ - enc_wbuf(enc, length, (u8 *) packet, 0x00); - /* - * Check that the internal transmit logic has not been altered - * by excessive collisions. Reset transmitter if so. - * See Errata B4 12 and 14. - */ - if (enc_r8(enc, CTL_REG_EIR) & ENC_EIR_TXERIF) { - enc_bset(enc, CTL_REG_ECON1, ENC_ECON1_TXRST); - enc_bclr(enc, CTL_REG_ECON1, ENC_ECON1_TXRST); - } - enc_bclr(enc, CTL_REG_EIR, (ENC_EIR_TXERIF | ENC_EIR_TXIF)); - /* start transmitting */ - enc_bset(enc, CTL_REG_ECON1, ENC_ECON1_TXRTS); - enc_release_bus(enc); - return 0; -} - -/* - * Finish use of ENC. - * - * This function entered into eth_device structure. - */ -static void enc_halt(struct eth_device *dev) -{ - enc_dev_t *enc = dev->priv; - - if (enc_claim_bus(enc)) - return; - /* Just disable receiver */ - enc_bclr(enc, CTL_REG_ECON1, ENC_ECON1_RXEN); - enc_release_bus(enc); -} - -/* - * This is the only exported function. - * - * It may be called several times with different bus:cs combinations. - */ -int enc28j60_initialize(unsigned int bus, unsigned int cs, - unsigned int max_hz, unsigned int mode) -{ - struct eth_device *dev; - enc_dev_t *enc; - - /* try to allocate, check and clear eth_device object */ - dev = malloc(sizeof(*dev)); - if (!dev) { - return -1; - } - memset(dev, 0, sizeof(*dev)); - - /* try to allocate, check and clear enc_dev_t object */ - enc = malloc(sizeof(*enc)); - if (!enc) { - free(dev); - return -1; - } - memset(enc, 0, sizeof(*enc)); - - /* try to setup the SPI slave */ - enc->slave = spi_setup_slave(bus, cs, max_hz, mode); - if (!enc->slave) { - printf("enc28j60: invalid SPI device %i:%i\n", bus, cs); - free(enc); - free(dev); - return -1; - } - - enc->dev = dev; - /* now fill the eth_device object */ - dev->priv = enc; - dev->init = enc_init; - dev->halt = enc_halt; - dev->send = enc_send; - dev->recv = enc_recv; - dev->write_hwaddr = enc_write_hwaddr; - sprintf(dev->name, "enc%i.%i", bus, cs); - eth_register(dev); -#if defined(CONFIG_CMD_MII) - int retval; - struct mii_dev *mdiodev = mdio_alloc(); - if (!mdiodev) - return -ENOMEM; - strncpy(mdiodev->name, dev->name, MDIO_NAME_LEN); - mdiodev->read = enc_miiphy_read; - mdiodev->write = enc_miiphy_write; - - retval = mdio_register(mdiodev); - if (retval < 0) - return retval; -#endif - return 0; -} diff --git a/drivers/net/enc28j60.h b/drivers/net/enc28j60.h deleted file mode 100644 index 289e41288e..0000000000 --- a/drivers/net/enc28j60.h +++ /dev/null @@ -1,238 +0,0 @@ -/* - * (X) extracted from enc28j60.c - * Reinhard Meyer, EMK Elektronik, reinhard.meyer@emk-elektronik.de - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _enc28j60_h -#define _enc28j60_h - -/* - * SPI Commands - * - * Bits 7-5: Command - * Bits 4-0: Register - */ -#define CMD_RCR(x) (0x00+((x)&0x1f)) /* Read Control Register */ -#define CMD_RBM 0x3a /* Read Buffer Memory */ -#define CMD_WCR(x) (0x40+((x)&0x1f)) /* Write Control Register */ -#define CMD_WBM 0x7a /* Write Buffer Memory */ -#define CMD_BFS(x) (0x80+((x)&0x1f)) /* Bit Field Set */ -#define CMD_BFC(x) (0xa0+((x)&0x1f)) /* Bit Field Clear */ -#define CMD_SRC 0xff /* System Reset Command */ - -/* NEW: encode (bank number+1) in upper byte */ - -/* Common Control Registers accessible in all Banks */ -#define CTL_REG_EIE 0x01B -#define CTL_REG_EIR 0x01C -#define CTL_REG_ESTAT 0x01D -#define CTL_REG_ECON2 0x01E -#define CTL_REG_ECON1 0x01F - -/* Control Registers accessible in Bank 0 */ -#define CTL_REG_ERDPTL 0x100 -#define CTL_REG_ERDPTH 0x101 -#define CTL_REG_EWRPTL 0x102 -#define CTL_REG_EWRPTH 0x103 -#define CTL_REG_ETXSTL 0x104 -#define CTL_REG_ETXSTH 0x105 -#define CTL_REG_ETXNDL 0x106 -#define CTL_REG_ETXNDH 0x107 -#define CTL_REG_ERXSTL 0x108 -#define CTL_REG_ERXSTH 0x109 -#define CTL_REG_ERXNDL 0x10A -#define CTL_REG_ERXNDH 0x10B -#define CTL_REG_ERXRDPTL 0x10C -#define CTL_REG_ERXRDPTH 0x10D -#define CTL_REG_ERXWRPTL 0x10E -#define CTL_REG_ERXWRPTH 0x10F -#define CTL_REG_EDMASTL 0x110 -#define CTL_REG_EDMASTH 0x111 -#define CTL_REG_EDMANDL 0x112 -#define CTL_REG_EDMANDH 0x113 -#define CTL_REG_EDMADSTL 0x114 -#define CTL_REG_EDMADSTH 0x115 -#define CTL_REG_EDMACSL 0x116 -#define CTL_REG_EDMACSH 0x117 - -/* Control Registers accessible in Bank 1 */ -#define CTL_REG_EHT0 0x200 -#define CTL_REG_EHT1 0x201 -#define CTL_REG_EHT2 0x202 -#define CTL_REG_EHT3 0x203 -#define CTL_REG_EHT4 0x204 -#define CTL_REG_EHT5 0x205 -#define CTL_REG_EHT6 0x206 -#define CTL_REG_EHT7 0x207 -#define CTL_REG_EPMM0 0x208 -#define CTL_REG_EPMM1 0x209 -#define CTL_REG_EPMM2 0x20A -#define CTL_REG_EPMM3 0x20B -#define CTL_REG_EPMM4 0x20C -#define CTL_REG_EPMM5 0x20D -#define CTL_REG_EPMM6 0x20E -#define CTL_REG_EPMM7 0x20F -#define CTL_REG_EPMCSL 0x210 -#define CTL_REG_EPMCSH 0x211 -#define CTL_REG_EPMOL 0x214 -#define CTL_REG_EPMOH 0x215 -#define CTL_REG_EWOLIE 0x216 -#define CTL_REG_EWOLIR 0x217 -#define CTL_REG_ERXFCON 0x218 -#define CTL_REG_EPKTCNT 0x219 - -/* Control Registers accessible in Bank 2 */ -#define CTL_REG_MACON1 0x300 -#define CTL_REG_MACON2 0x301 -#define CTL_REG_MACON3 0x302 -#define CTL_REG_MACON4 0x303 -#define CTL_REG_MABBIPG 0x304 -#define CTL_REG_MAIPGL 0x306 -#define CTL_REG_MAIPGH 0x307 -#define CTL_REG_MACLCON1 0x308 -#define CTL_REG_MACLCON2 0x309 -#define CTL_REG_MAMXFLL 0x30A -#define CTL_REG_MAMXFLH 0x30B -#define CTL_REG_MAPHSUP 0x30D -#define CTL_REG_MICON 0x311 -#define CTL_REG_MICMD 0x312 -#define CTL_REG_MIREGADR 0x314 -#define CTL_REG_MIWRL 0x316 -#define CTL_REG_MIWRH 0x317 -#define CTL_REG_MIRDL 0x318 -#define CTL_REG_MIRDH 0x319 - -/* Control Registers accessible in Bank 3 */ -#define CTL_REG_MAADR1 0x400 -#define CTL_REG_MAADR0 0x401 -#define CTL_REG_MAADR3 0x402 -#define CTL_REG_MAADR2 0x403 -#define CTL_REG_MAADR5 0x404 -#define CTL_REG_MAADR4 0x405 -#define CTL_REG_EBSTSD 0x406 -#define CTL_REG_EBSTCON 0x407 -#define CTL_REG_EBSTCSL 0x408 -#define CTL_REG_EBSTCSH 0x409 -#define CTL_REG_MISTAT 0x40A -#define CTL_REG_EREVID 0x412 -#define CTL_REG_ECOCON 0x415 -#define CTL_REG_EFLOCON 0x417 -#define CTL_REG_EPAUSL 0x418 -#define CTL_REG_EPAUSH 0x419 - -/* PHY Register */ -#define PHY_REG_PHCON1 0x00 -#define PHY_REG_PHSTAT1 0x01 -#define PHY_REG_PHID1 0x02 -#define PHY_REG_PHID2 0x03 -#define PHY_REG_PHCON2 0x10 -#define PHY_REG_PHSTAT2 0x11 -#define PHY_REG_PHLCON 0x14 - -/* Receive Filter Register (ERXFCON) bits */ -#define ENC_RFR_UCEN 0x80 -#define ENC_RFR_ANDOR 0x40 -#define ENC_RFR_CRCEN 0x20 -#define ENC_RFR_PMEN 0x10 -#define ENC_RFR_MPEN 0x08 -#define ENC_RFR_HTEN 0x04 -#define ENC_RFR_MCEN 0x02 -#define ENC_RFR_BCEN 0x01 - -/* ECON1 Register Bits */ -#define ENC_ECON1_TXRST 0x80 -#define ENC_ECON1_RXRST 0x40 -#define ENC_ECON1_DMAST 0x20 -#define ENC_ECON1_CSUMEN 0x10 -#define ENC_ECON1_TXRTS 0x08 -#define ENC_ECON1_RXEN 0x04 -#define ENC_ECON1_BSEL1 0x02 -#define ENC_ECON1_BSEL0 0x01 - -/* ECON2 Register Bits */ -#define ENC_ECON2_AUTOINC 0x80 -#define ENC_ECON2_PKTDEC 0x40 -#define ENC_ECON2_PWRSV 0x20 -#define ENC_ECON2_VRPS 0x08 - -/* EIR Register Bits */ -#define ENC_EIR_PKTIF 0x40 -#define ENC_EIR_DMAIF 0x20 -#define ENC_EIR_LINKIF 0x10 -#define ENC_EIR_TXIF 0x08 -#define ENC_EIR_WOLIF 0x04 -#define ENC_EIR_TXERIF 0x02 -#define ENC_EIR_RXERIF 0x01 - -/* ESTAT Register Bits */ -#define ENC_ESTAT_INT 0x80 -#define ENC_ESTAT_LATECOL 0x10 -#define ENC_ESTAT_RXBUSY 0x04 -#define ENC_ESTAT_TXABRT 0x02 -#define ENC_ESTAT_CLKRDY 0x01 - -/* EIE Register Bits */ -#define ENC_EIE_INTIE 0x80 -#define ENC_EIE_PKTIE 0x40 -#define ENC_EIE_DMAIE 0x20 -#define ENC_EIE_LINKIE 0x10 -#define ENC_EIE_TXIE 0x08 -#define ENC_EIE_WOLIE 0x04 -#define ENC_EIE_TXERIE 0x02 -#define ENC_EIE_RXERIE 0x01 - -/* MACON1 Register Bits */ -#define ENC_MACON1_LOOPBK 0x10 -#define ENC_MACON1_TXPAUS 0x08 -#define ENC_MACON1_RXPAUS 0x04 -#define ENC_MACON1_PASSALL 0x02 -#define ENC_MACON1_MARXEN 0x01 - -/* MACON2 Register Bits */ -#define ENC_MACON2_MARST 0x80 -#define ENC_MACON2_RNDRST 0x40 -#define ENC_MACON2_MARXRST 0x08 -#define ENC_MACON2_RFUNRST 0x04 -#define ENC_MACON2_MATXRST 0x02 -#define ENC_MACON2_TFUNRST 0x01 - -/* MACON3 Register Bits */ -#define ENC_MACON3_PADCFG2 0x80 -#define ENC_MACON3_PADCFG1 0x40 -#define ENC_MACON3_PADCFG0 0x20 -#define ENC_MACON3_TXCRCEN 0x10 -#define ENC_MACON3_PHDRLEN 0x08 -#define ENC_MACON3_HFRMEN 0x04 -#define ENC_MACON3_FRMLNEN 0x02 -#define ENC_MACON3_FULDPX 0x01 - -/* MACON4 Register Bits */ -#define ENC_MACON4_DEFER 0x40 - -/* MICMD Register Bits */ -#define ENC_MICMD_MIISCAN 0x02 -#define ENC_MICMD_MIIRD 0x01 - -/* MISTAT Register Bits */ -#define ENC_MISTAT_NVALID 0x04 -#define ENC_MISTAT_SCAN 0x02 -#define ENC_MISTAT_BUSY 0x01 - -/* PHID1 and PHID2 values */ -#define ENC_PHID1_VALUE 0x0083 -#define ENC_PHID2_VALUE 0x1400 -#define ENC_PHID2_MASK 0xFC00 - -/* PHCON1 values */ -#define ENC_PHCON1_PDPXMD 0x0100 - -/* PHSTAT1 values */ -#define ENC_PHSTAT1_LLSTAT 0x0004 - -/* PHSTAT2 values */ -#define ENC_PHSTAT2_LSTAT 0x0400 -#define ENC_PHSTAT2_DPXSTAT 0x0200 - -#endif diff --git a/include/netdev.h b/include/netdev.h index 3958a4cd32..86d28ade14 100644 --- a/include/netdev.h +++ b/include/netdev.h @@ -39,8 +39,6 @@ int dm9000_initialize(bd_t *bis); int dnet_eth_initialize(int id, void *regs, unsigned int phy_addr); int e1000_initialize(bd_t *bis); int eepro100_initialize(bd_t *bis); -int enc28j60_initialize(unsigned int bus, unsigned int cs, - unsigned int max_hz, unsigned int mode); int ep93xx_eth_initialize(u8 dev_num, int base_addr); int eth_3com_initialize (bd_t * bis); int ethoc_initialize(u8 dev_num, int base_addr);