From: Marek Vasut Date: Wed, 22 Oct 2014 19:34:51 +0000 (+0200) Subject: ppc: Zap TQM8260 board X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=ccc1950010f9332bfcc2858db02e15efe0f3ca85;p=u-boot.git ppc: Zap TQM8260 board This board is old and is using CONFIG_I2C_X, which is wrong. Signed-off-by: Marek Vasut Cc: Masahiro Yamada Cc: Tom Rini Cc: Wolfgang Denk Cc: Simon Glass Cc: Heiko Schocher --- diff --git a/arch/powerpc/cpu/mpc8260/Kconfig b/arch/powerpc/cpu/mpc8260/Kconfig index 7e28170a4a..e28628fa59 100644 --- a/arch/powerpc/cpu/mpc8260/Kconfig +++ b/arch/powerpc/cpu/mpc8260/Kconfig @@ -55,9 +55,6 @@ config TARGET_VOVPN_GW config TARGET_KM82XX bool "Support km82xx" -config TARGET_TQM8260 - bool "Support TQM8260" - config TARGET_TQM8272 bool "Support TQM8272" @@ -79,7 +76,6 @@ source "board/pm826/Kconfig" source "board/pm828/Kconfig" source "board/ppmc8260/Kconfig" source "board/sacsng/Kconfig" -source "board/tqc/tqm8260/Kconfig" source "board/tqc/tqm8272/Kconfig" endmenu diff --git a/board/tqc/tqm8260/Kconfig b/board/tqc/tqm8260/Kconfig deleted file mode 100644 index 90a96ebebe..0000000000 --- a/board/tqc/tqm8260/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_TQM8260 - -config SYS_BOARD - default "tqm8260" - -config SYS_VENDOR - default "tqc" - -config SYS_CONFIG_NAME - default "TQM8260" - -endif diff --git a/board/tqc/tqm8260/MAINTAINERS b/board/tqc/tqm8260/MAINTAINERS deleted file mode 100644 index 266910fe05..0000000000 --- a/board/tqc/tqm8260/MAINTAINERS +++ /dev/null @@ -1,16 +0,0 @@ -TQM8260 BOARD -M: Wolfgang Denk -S: Maintained -F: board/tqc/tqm8260/ -F: include/configs/TQM8260.h -F: configs/TQM8255_AA_defconfig -F: configs/TQM8260_AA_defconfig -F: configs/TQM8260_AB_defconfig -F: configs/TQM8260_AC_defconfig -F: configs/TQM8260_AD_defconfig -F: configs/TQM8260_AE_defconfig -F: configs/TQM8260_AF_defconfig -F: configs/TQM8260_AG_defconfig -F: configs/TQM8260_AH_defconfig -F: configs/TQM8260_AI_defconfig -F: configs/TQM8265_AA_defconfig diff --git a/board/tqc/tqm8260/Makefile b/board/tqc/tqm8260/Makefile deleted file mode 100644 index 6b8573d9ab..0000000000 --- a/board/tqc/tqm8260/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2001-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = tqm8260.o ../tqm8xx/load_sernum_ethaddr.o diff --git a/board/tqc/tqm8260/README b/board/tqc/tqm8260/README deleted file mode 100644 index 93b55068f5..0000000000 --- a/board/tqc/tqm8260/README +++ /dev/null @@ -1,415 +0,0 @@ - -This file contains basic information on the port of U-Boot to TQM8260. -All the changes fit in the common U-Boot infrastructure, providing a -new TQM8260-specific entry in makefiles. To build U-Boot for TQM8260, -type "make TQM8260_config", edit the "include/config_TQM8260.h" file -if necessary, then type "make". - - -Common file modifications: --------------------------- - -The following common files have been modified by this project: -(starting from the ppcboot-0.9.3/ directory) - -MAKEALL - TQM8260 entry added -Makefile - TQM8260_config entry added -arch/powerpc/cpu/mpc8260/Makefile - soft_i2c.o module added -arch/powerpc/cpu/mpc8260/ether_scc.c - TQM8260-specific definitions added, an obvious - bug fixed (fcr -> scr) -arch/powerpc/cpu/mpc8260/ether_fcc.c - TQM8260-specific definitions added -include/flash.h - added definitions for the AM29LV640D Flash chip - - -New files: ----------- - -The following new files have been added by this project: -(starting from the ppcboot-0.9.3/ directory) - -board/tqm8260/ - board-specific directory -board/tqm8260/Makefile - board-specific makefile -board/tqm8260/config.mk - config file -board/tqm8260/flash.c - flash driver (for AM29LV640D) -board/tqm8260/ppcboot.lds - linker script -board/tqm8260/tqm8260.c - ioport and memory initialization -arch/powerpc/cpu/mpc8260/soft_i2c.c - software i2c EEPROM driver -include/config_TQM8260.h - main configuration file - - -New configuration options: --------------------------- - -CONFIG_TQM8260 - - Main board-specific option (should be defined for TQM8260). - -CONFIG_82xx_CONS_SMC1 - - If defined, SMC1 will be used as the console - -CONFIG_82xx_CONS_SMC2 - - If defined, SMC2 will be used as the console - -CONFIG_SYS_INIT_LOCAL_SDRAM - - If defined, the SDRAM on the local bus will be initialized and - mapped at BR2. - - -Acceptance criteria tests: --------------------------- - -The following tests have been conducted to validate the port of U-Boot -to TQM8260: - -1. Operation on serial console: - -With the CONFIG_82xx_CONS_SMC1 option defined in the main configuration file, -the U-Boot output appeared on the serial terminal connected to COM1 as -follows: - ------------------------------------------------------------------------------- -=> help -go - start application at address 'addr' -run - run commands in an environment variable -bootm - boot application image from memory -bootp - boot image via network using BootP/TFTP protocol -tftpboot- boot image via network using TFTP protocol - and env variables ipaddr and serverip -rarpboot- boot image via network using RARP/TFTP protocol -bootd - boot default, i.e., run 'bootcmd' -loads - load S-Record file over serial line -loadb - load binary file over serial line (kermit mode) -md - memory display -mm - memory modify (auto-incrementing) -nm - memory modify (constant address) -mw - memory write (fill) -cp - memory copy -cmp - memory compare -crc32 - checksum calculation -base - print or set address offset -printenv- print environment variables -setenv - set environment variables -saveenv - save environment variables to persistent storage -protect - enable or disable FLASH write protection -erase - erase FLASH memory -flinfo - print FLASH memory information -bdinfo - print Board Info structure -iminfo - print header information for application image -coninfo - print console devices and informations -eeprom - EEPROM sub-system -loop - infinite loop on address range -mtest - simple RAM test -icache - enable or disable instruction cache -dcache - enable or disable data cache -reset - Perform RESET of the CPU -echo - echo args to console -version - print monitor version -help - print online help -? - alias for 'help' -=> ------------------------------------------------------------------------------- - - -2. Flash driver operation - -The following sequence was performed to test the "flinfo" command: - ------------------------------------------------------------------------------- -=> flinfo - -Bank # 1: AMD 29LV640D (64 M, uniform sector) - Size: 32 MB in 128 Sectors - Sector Start Addresses: - 40000000 40040000 (RO) 40080000 400C0000 40100000 - 40140000 40180000 401C0000 40200000 40240000 - 40280000 402C0000 40300000 40340000 40380000 - 403C0000 40400000 40440000 40480000 404C0000 - 40500000 40540000 40580000 405C0000 40600000 - 40640000 40680000 406C0000 40700000 40740000 - 40780000 407C0000 40800000 40840000 40880000 - 408C0000 40900000 40940000 40980000 409C0000 - 40A00000 40A40000 40A80000 40AC0000 40B00000 - 40B40000 40B80000 40BC0000 40C00000 40C40000 - 40C80000 40CC0000 40D00000 40D40000 40D80000 - 40DC0000 40E00000 40E40000 40E80000 40EC0000 - 40F00000 40F40000 40F80000 40FC0000 41000000 - 41040000 41080000 410C0000 41100000 41140000 - 41180000 411C0000 41200000 41240000 41280000 - 412C0000 41300000 41340000 41380000 413C0000 - 41400000 41440000 41480000 414C0000 41500000 - 41540000 41580000 415C0000 41600000 41640000 - 41680000 416C0000 41700000 41740000 41780000 - 417C0000 41800000 41840000 41880000 418C0000 - 41900000 41940000 41980000 419C0000 41A00000 - 41A40000 41A80000 41AC0000 41B00000 41B40000 - 41B80000 41BC0000 41C00000 41C40000 41C80000 - 41CC0000 41D00000 41D40000 41D80000 41DC0000 - 41E00000 41E40000 41E80000 41EC0000 41F00000 - 41F40000 41F80000 41FC0000 -=> ------------------------------------------------------------------------------- - - -The following sequence was performed to test the erase command: - ------------------------------------------------------------------------------- -=> cp 0 40080000 10 -Copy to Flash... done -=> erase 40080000 400bffff -Erase Flash from 0x40080000 to 0x400bffff -.. done -Erased 1 sectors -=> md 40080000 -40080000: ffffffff ffffffff ffffffff ffffffff ................ -40080010: ffffffff ffffffff ffffffff ffffffff ................ -40080020: ffffffff ffffffff ffffffff ffffffff ................ -40080030: ffffffff ffffffff ffffffff ffffffff ................ -40080040: ffffffff ffffffff ffffffff ffffffff ................ -40080050: ffffffff ffffffff ffffffff ffffffff ................ -40080060: ffffffff ffffffff ffffffff ffffffff ................ -40080070: ffffffff ffffffff ffffffff ffffffff ................ -40080080: ffffffff ffffffff ffffffff ffffffff ................ -40080090: ffffffff ffffffff ffffffff ffffffff ................ -400800a0: ffffffff ffffffff ffffffff ffffffff ................ -400800b0: ffffffff ffffffff ffffffff ffffffff ................ -400800c0: ffffffff ffffffff ffffffff ffffffff ................ -400800d0: ffffffff ffffffff ffffffff ffffffff ................ -400800e0: ffffffff ffffffff ffffffff ffffffff ................ -400800f0: ffffffff ffffffff ffffffff ffffffff ................ -=> cp 0 40080000 10 -Copy to Flash... done -=> erase 1:2 -Erase Flash Sectors 2-2 in Bank # 1 -.. done -=> md 40080000 -40080000: ffffffff ffffffff ffffffff ffffffff ................ -40080010: ffffffff ffffffff ffffffff ffffffff ................ -40080020: ffffffff ffffffff ffffffff ffffffff ................ -40080030: ffffffff ffffffff ffffffff ffffffff ................ -40080040: ffffffff ffffffff ffffffff ffffffff ................ -40080050: ffffffff ffffffff ffffffff ffffffff ................ -40080060: ffffffff ffffffff ffffffff ffffffff ................ -40080070: ffffffff ffffffff ffffffff ffffffff ................ -40080080: ffffffff ffffffff ffffffff ffffffff ................ -40080090: ffffffff ffffffff ffffffff ffffffff ................ -400800a0: ffffffff ffffffff ffffffff ffffffff ................ -400800b0: ffffffff ffffffff ffffffff ffffffff ................ -400800c0: ffffffff ffffffff ffffffff ffffffff ................ -400800d0: ffffffff ffffffff ffffffff ffffffff ................ -400800e0: ffffffff ffffffff ffffffff ffffffff ................ -400800f0: ffffffff ffffffff ffffffff ffffffff ................ -=> cp 0 40080000 10 -Copy to Flash... done -=> cp 0 400c0000 10 -Copy to Flash... done -=> erase 1:2-3 -Erase Flash Sectors 2-3 in Bank # 1 -... done -=> md 40080000 -40080000: ffffffff ffffffff ffffffff ffffffff ................ -40080010: ffffffff ffffffff ffffffff ffffffff ................ -40080020: ffffffff ffffffff ffffffff ffffffff ................ -40080030: ffffffff ffffffff ffffffff ffffffff ................ -40080040: ffffffff ffffffff ffffffff ffffffff ................ -40080050: ffffffff ffffffff ffffffff ffffffff ................ -40080060: ffffffff ffffffff ffffffff ffffffff ................ -40080070: ffffffff ffffffff ffffffff ffffffff ................ -40080080: ffffffff ffffffff ffffffff ffffffff ................ -40080090: ffffffff ffffffff ffffffff ffffffff ................ -400800a0: ffffffff ffffffff ffffffff ffffffff ................ -400800b0: ffffffff ffffffff ffffffff ffffffff ................ -400800c0: ffffffff ffffffff ffffffff ffffffff ................ -400800d0: ffffffff ffffffff ffffffff ffffffff ................ -400800e0: ffffffff ffffffff ffffffff ffffffff ................ -400800f0: ffffffff ffffffff ffffffff ffffffff ................ -=> md 400c0000 -400c0000: ffffffff ffffffff ffffffff ffffffff ................ -400c0010: ffffffff ffffffff ffffffff ffffffff ................ -400c0020: ffffffff ffffffff ffffffff ffffffff ................ -400c0030: ffffffff ffffffff ffffffff ffffffff ................ -400c0040: ffffffff ffffffff ffffffff ffffffff ................ -400c0050: ffffffff ffffffff ffffffff ffffffff ................ -400c0060: ffffffff ffffffff ffffffff ffffffff ................ -400c0070: ffffffff ffffffff ffffffff ffffffff ................ -400c0080: ffffffff ffffffff ffffffff ffffffff ................ -400c0090: ffffffff ffffffff ffffffff ffffffff ................ -400c00a0: ffffffff ffffffff ffffffff ffffffff ................ -400c00b0: ffffffff ffffffff ffffffff ffffffff ................ -400c00c0: ffffffff ffffffff ffffffff ffffffff ................ -400c00d0: ffffffff ffffffff ffffffff ffffffff ................ -400c00e0: ffffffff ffffffff ffffffff ffffffff ................ -400c00f0: ffffffff ffffffff ffffffff ffffffff ................ -=> ------------------------------------------------------------------------------- - - -The following sequence was performed to test the Flash programming commands: - ------------------------------------------------------------------------------- -=> erase 40080000 400bffff -Erase Flash from 0x40080000 to 0x400bffff -.. done -Erased 1 sectors -=> cp 0 40080000 10 -Copy to Flash... done -=> md 0 -00000000: 00000000 00000104 61100200 01000000 ........a....... -00000010: 00000000 00000000 81140000 82000100 ................ -00000020: 01080000 00004000 22800000 00000600 ......@."....... -00000030: 00200800 00000000 10000100 00008000 . .............. -00000040: 00812000 00000200 00020000 80000000 .. ............. -00000050: 00028001 00001000 00040400 00000200 ................ -00000060: 20480000 00000000 20090000 00142000 H...... ..... . -00000070: 00000000 00004000 24210000 10000000 ......@.$!...... -00000080: 02440002 10000000 00200008 00000000 .D....... ...... -00000090: 02440900 00000000 30a40000 00004400 .D......0.....D. -000000a0: 04420800 00000000 00000040 00020000 .B.........@.... -000000b0: 05020000 00100000 00060000 00000000 ................ -000000c0: 00400000 00000000 00080000 00040000 .@.............. -000000d0: 10400000 00800004 00000000 00000200 .@.............. -000000e0: 80890000 00010004 00080000 00000020 ............... -000000f0: 08000000 10000000 00010000 00000000 ................ -=> md 40080000 -40080000: 00000000 00000104 61100200 01000000 ........a....... -40080010: 00000000 00000000 81140000 82000100 ................ -40080020: 01080000 00004000 22800000 00000600 ......@."....... -40080030: 00200800 00000000 10000100 00008000 . .............. -40080040: ffffffff ffffffff ffffffff ffffffff ................ -40080050: ffffffff ffffffff ffffffff ffffffff ................ -40080060: ffffffff ffffffff ffffffff ffffffff ................ -40080070: ffffffff ffffffff ffffffff ffffffff ................ -40080080: ffffffff ffffffff ffffffff ffffffff ................ -40080090: ffffffff ffffffff ffffffff ffffffff ................ -400800a0: ffffffff ffffffff ffffffff ffffffff ................ -400800b0: ffffffff ffffffff ffffffff ffffffff ................ -400800c0: ffffffff ffffffff ffffffff ffffffff ................ -400800d0: ffffffff ffffffff ffffffff ffffffff ................ -400800e0: ffffffff ffffffff ffffffff ffffffff ................ -400800f0: ffffffff ffffffff ffffffff ffffffff ................ -=> ------------------------------------------------------------------------------- - - -The following sequence was performed to test storage of the environment -variables in Flash: - ------------------------------------------------------------------------------- -=> setenv foo bar -=> saveenv -Un-Protected 1 sectors -Erasing Flash... -.. done -Erased 1 sectors -Saving Environment to Flash... -Protected 1 sectors -=> reset -... -=> printenv -bootdelay=CONFIG_BOOTDELAY -baudrate=9600 -ipaddr=192.168.4.7 -serverip=192.168.4.1 -ethaddr=66:55:44:33:22:11 -foo=bar -stdin=serial -stdout=serial -stderr=serial - -Environment size: 170/262140 bytes -=> ------------------------------------------------------------------------------- - - -The following sequence was performed to test image download and run over -Ethernet interface (both interfaces were tested): - ------------------------------------------------------------------------------- -=> tftpboot 40000 hello_world.bin -ARP broadcast 1 -TFTP from server 192.168.2.2; our IP address is 192.168.2.7 -Filename 'hello_world.bin'. -Load address: 0x40000 -Loading: ############# -done -Bytes transferred = 65912 (10178 hex) -=> go 40004 -## Starting application at 0x00040004 ... -Hello World -argc = 1 -argv[0] = "40004" -argv[1] = "" -Hit any key to exit ... - -## Application terminated, rc = 0x0 -=> ------------------------------------------------------------------------------- - - -The following sequence was performed to test eeprom read/write commands: - ------------------------------------------------------------------------------- -=> md 40000 -00040000: 00018148 9421ffe0 7c0802a6 bf61000c ...H.!..|....a.. -00040010: 90010024 48000005 7fc802a6 801effe8 ...$H........... -00040020: 7fc0f214 7c7f1b78 813f004c 7c9c2378 ....|..x.?.L|.#x -00040030: 807e8000 7cbd2b78 80090010 3b600000 .~..|.+x....;`.. -00040040: 7c0803a6 4e800021 813f004c 7f84e378 |...N..!.?.L...x -00040050: 807e8004 80090010 7c0803a6 4e800021 .~......|...N..! -00040060: 7c1be000 4181003c 80bd0000 813f004c |...A..<.....?.L -00040070: 3bbd0004 2c050000 40820008 80be8008 ;...,...@....... -00040080: 80090010 7f64db78 807e800c 3b7b0001 .....d.x.~..;{.. -00040090: 7c0803a6 4e800021 7c1be000 4081ffcc |...N..!|...@... -000400a0: 813f004c 807e8010 80090010 7c0803a6 .?.L.~......|... -000400b0: 4e800021 813f004c 80090004 7c0803a6 N..!.?.L....|... -000400c0: 4e800021 2c030000 4182ffec 813f004c N..!,...A....?.L -000400d0: 80090000 7c0803a6 4e800021 813f004c ....|...N..!.?.L -000400e0: 807e8014 80090010 7c0803a6 4e800021 .~......|...N..! -000400f0: 38600000 80010024 7c0803a6 bb61000c 8`.....$|....a.. -=> eeprom write 40000 0 40 - -EEPROM write: addr 00040000 off 0000 count 64 ... done -=> mw 50000 0 1000 -=> eeprom read 50000 0 40 - -EEPROM read: addr 00050000 off 0000 count 64 ... done -=> md 50000 -00050000: 00018148 9421ffe0 7c0802a6 bf61000c ...H.!..|....a.. -00050010: 90010024 48000005 7fc802a6 801effe8 ...$H........... -00050020: 7fc0f214 7c7f1b78 813f004c 7c9c2378 ....|..x.?.L|.#x -00050030: 807e8000 7cbd2b78 80090010 3b600000 .~..|.+x....;`.. -00050040: 00000000 00000000 00000000 00000000 ................ -00050050: 00000000 00000000 00000000 00000000 ................ -00050060: 00000000 00000000 00000000 00000000 ................ -00050070: 00000000 00000000 00000000 00000000 ................ -00050080: 00000000 00000000 00000000 00000000 ................ -00050090: 00000000 00000000 00000000 00000000 ................ -000500a0: 00000000 00000000 00000000 00000000 ................ -000500b0: 00000000 00000000 00000000 00000000 ................ -000500c0: 00000000 00000000 00000000 00000000 ................ -000500d0: 00000000 00000000 00000000 00000000 ................ -000500e0: 00000000 00000000 00000000 00000000 ................ -000500f0: 00000000 00000000 00000000 00000000 ................ -=> ------------------------------------------------------------------------------- - - -Patch per Mon, 06 Aug 2001 17:57:27: - -- upgraded Flash support (added support for the following chips: - AM29LV800T/B, AM29LV160T/B, AM29DL322T/B, AM29DL323T/B) -- BCR tweakage for the 8260 bus mode -- SIUMCR tweakage enabling the MI interrupt (IRQ7) - -To simplify switching between the bus modes, a new configuration -option (CONFIG_BUSMODE_60x) has been added to the "config_TQM8260.h" -file. If it is defined, BCR will be configured for the 60x mode, -otherwise - for the 8260 mode. - -Concerning the SIUMCR modification: it's hard to predict whether it -will induce any problems on the other (60x mode) board. However, the -problems (if they appear) should be easy to notice - if the board -does not boot, it's most likely caused by the DPPC configuration in -SIUMCR. diff --git a/board/tqc/tqm8260/tqm8260.c b/board/tqc/tqm8260/tqm8260.c deleted file mode 100644 index c361f188f7..0000000000 --- a/board/tqc/tqm8260/tqm8260.c +++ /dev/null @@ -1,352 +0,0 @@ -/* - * (C) Copyright 2001 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include - -/* - * I/O Port configuration table - * - * if conf is 1, then that port pin will be configured at boot time - * according to the five values podr/pdir/ppar/psor/pdat for that entry - */ - -const iop_conf_t iop_conf_tab[4][32] = { - - /* Port A configuration */ - { /* conf ppar psor pdir podr pdat */ - /* PA31 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 *ATMTXEN */ - /* PA30 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTCA */ - /* PA29 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTSOC */ - /* PA28 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 *ATMRXEN */ - /* PA27 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRSOC */ - /* PA26 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRCA */ - /* PA25 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */ - /* PA24 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */ - /* PA23 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */ - /* PA22 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */ - /* PA21 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */ - /* PA20 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */ - /* PA19 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */ - /* PA18 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */ - /* PA17 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[7] */ - /* PA16 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[6] */ - /* PA15 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[5] */ - /* PA14 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[4] */ - /* PA13 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[3] */ - /* PA12 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[2] */ - /* PA11 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[1] */ - /* PA10 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[0] */ - /* PA9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC2 TXD */ - /* PA8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC2 RXD */ - /* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */ - /* PA6 */ { 0, 0, 0, 1, 0, 0 }, /* PA6 */ - /* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */ - /* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */ - /* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */ - /* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */ - /* PA1 */ { 0, 0, 0, 1, 0, 0 }, /* PA1 */ - /* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */ - }, - - /* Port B configuration */ - { /* conf ppar psor pdir podr pdat */ - /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */ - /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */ - /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */ - /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */ - /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */ - /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */ - /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */ - /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */ - /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */ - /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */ - /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */ - /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */ - /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */ - /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */ - /* PB17 */ { 0, 0, 0, 0, 0, 0 }, /* PB17 */ - /* PB16 */ { 0, 0, 0, 0, 0, 0 }, /* PB16 */ - /* PB15 */ { 0, 0, 0, 0, 0, 0 }, /* PB15 */ - /* PB14 */ { 0, 0, 0, 0, 0, 0 }, /* PB14 */ - /* PB13 */ { 0, 0, 0, 0, 0, 0 }, /* PB13 */ - /* PB12 */ { 0, 0, 0, 0, 0, 0 }, /* PB12 */ - /* PB11 */ { 0, 0, 0, 0, 0, 0 }, /* PB11 */ - /* PB10 */ { 0, 0, 0, 0, 0, 0 }, /* PB10 */ - /* PB9 */ { 0, 0, 0, 0, 0, 0 }, /* PB9 */ - /* PB8 */ { 0, 0, 0, 0, 0, 0 }, /* PB8 */ - /* PB7 */ { 0, 0, 0, 0, 0, 0 }, /* PB7 */ - /* PB6 */ { 0, 0, 0, 0, 0, 0 }, /* PB6 */ - /* PB5 */ { 0, 0, 0, 0, 0, 0 }, /* PB5 */ - /* PB4 */ { 0, 0, 0, 0, 0, 0 }, /* PB4 */ - /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - }, - - /* Port C */ - { /* conf ppar psor pdir podr pdat */ - /* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */ - /* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */ - /* PC29 */ { 1, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */ - /* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */ - /* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* PC27 */ - /* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */ - /* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */ - /* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */ - /* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */ - /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */ - /* PC21 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */ - /* PC20 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */ - /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK */ - /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII TX_CLK */ - /* PC17 */ { 0, 0, 0, 1, 0, 0 }, /* PC17 */ - /* PC16 */ { 0, 0, 0, 1, 0, 0 }, /* PC16 */ - /* PC15 */ { 0, 0, 0, 1, 0, 0 }, /* PC15 */ - /* PC14 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */ - /* PC13 */ { 0, 0, 0, 1, 0, 0 }, /* PC13 */ - /* PC12 */ { 0, 0, 0, 1, 0, 0 }, /* PC12 */ - /* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* PC11 */ - /* PC10 */ { 0, 0, 0, 1, 0, 0 }, /* FCC2 MDC */ - /* PC9 */ { 0, 0, 0, 1, 0, 0 }, /* FCC2 MDIO */ - /* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */ - /* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */ - /* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */ - /* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */ - /* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */ - /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */ - /* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */ - /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */ - /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */ - }, - - /* Port D */ - { /* conf ppar psor pdir podr pdat */ - /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */ - /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */ - /* PD29 */ { 1, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */ - /* PD28 */ { 0, 0, 0, 1, 0, 0 }, /* PD28 */ - /* PD27 */ { 0, 0, 0, 1, 0, 0 }, /* PD27 */ - /* PD26 */ { 0, 0, 0, 1, 0, 0 }, /* PD26 */ - /* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */ - /* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */ - /* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */ - /* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */ - /* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */ - /* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */ - /* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */ - /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */ - /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */ - /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */ -#if defined(CONFIG_SYS_I2C_SOFT) - /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SDA */ - /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SCL */ -#else -#if defined(CONFIG_HARD_I2C) - /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */ - /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */ -#else /* normal I/O port pins */ - /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */ - /* PD14 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SCL */ -#endif -#endif - /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */ - /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */ - /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */ - /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */ - /* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TXD */ - /* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RXD */ - /* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */ - /* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */ - /* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */ - /* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */ - /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - } -}; - -/* ------------------------------------------------------------------------- */ - -/* Check Board Identity: - */ -int checkboard (void) -{ - char buf[64]; - int i = getenv_f("serial#", buf, sizeof(buf)); - - puts ("Board: "); - - if (i < 0 || strncmp(buf, "TQM82", 5)) { - puts ("### No HW ID - assuming TQM8260\n"); - return (0); - } - - puts (buf); - putc ('\n'); - - return 0; -} - -/* ------------------------------------------------------------------------- */ - -/* Try SDRAM initialization with P/LSDMR=sdmr and ORx=orx - * - * This routine performs standard 8260 initialization sequence - * and calculates the available memory size. It may be called - * several times to try different SDRAM configurations on both - * 60x and local buses. - */ -static long int try_init (volatile memctl8260_t * memctl, ulong sdmr, - ulong orx, volatile uchar * base) -{ - volatile uchar c = 0xff; - volatile uint *sdmr_ptr; - volatile uint *orx_ptr; - ulong maxsize, size; - int i; - - /* We must be able to test a location outsize the maximum legal size - * to find out THAT we are outside; but this address still has to be - * mapped by the controller. That means, that the initial mapping has - * to be (at least) twice as large as the maximum expected size. - */ - maxsize = (1 + (~orx | 0x7fff)) / 2; - - /* Since CONFIG_SYS_SDRAM_BASE is always 0 (??), we assume that - * we are configuring CS1 if base != 0 - */ - sdmr_ptr = base ? &memctl->memc_lsdmr : &memctl->memc_psdmr; - orx_ptr = base ? &memctl->memc_or2 : &memctl->memc_or1; - - *orx_ptr = orx; - - /* - * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35): - * - * "At system reset, initialization software must set up the - * programmable parameters in the memory controller banks registers - * (ORx, BRx, P/LSDMR). After all memory parameters are configured, - * system software should execute the following initialization sequence - * for each SDRAM device. - * - * 1. Issue a PRECHARGE-ALL-BANKS command - * 2. Issue eight CBR REFRESH commands - * 3. Issue a MODE-SET command to initialize the mode register - * - * The initial commands are executed by setting P/LSDMR[OP] and - * accessing the SDRAM with a single-byte transaction." - * - * The appropriate BRx/ORx registers have already been set when we - * get here. The SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE. - */ - - *sdmr_ptr = sdmr | PSDMR_OP_PREA; - *base = c; - - *sdmr_ptr = sdmr | PSDMR_OP_CBRR; - for (i = 0; i < 8; i++) - *base = c; - - *sdmr_ptr = sdmr | PSDMR_OP_MRW; - *(base + CONFIG_SYS_MRS_OFFS) = c; /* setting MR on address lines */ - - *sdmr_ptr = sdmr | PSDMR_OP_NORM | PSDMR_RFEN; - *base = c; - - size = get_ram_size((long *)base, maxsize); - *orx_ptr = orx | ~(size - 1); - - return (size); -} - -phys_size_t initdram (int board_type) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile memctl8260_t *memctl = &immap->im_memctl; - -#ifndef CONFIG_SYS_RAMBOOT - long size8, size9; -#endif - long psize, lsize; - - psize = 16 * 1024 * 1024; - lsize = 0; - - memctl->memc_psrt = CONFIG_SYS_PSRT; - memctl->memc_mptpr = CONFIG_SYS_MPTPR; - -#if 0 /* Just for debugging */ -#define prt_br_or(brX,orX) do { \ - ulong start = memctl->memc_ ## brX & 0xFFFF8000; \ - ulong sizem = ~memctl->memc_ ## orX | 0x00007FFF; \ - printf ("\n" \ - #brX " 0x%08x " #orX " 0x%08x " \ - "==> 0x%08lx ... 0x%08lx = %ld MB\n", \ - memctl->memc_ ## brX, memctl->memc_ ## orX, \ - start, start+sizem, (sizem+1)>>20); \ - } while (0) - prt_br_or (br0, or0); - prt_br_or (br1, or1); - prt_br_or (br2, or2); - prt_br_or (br3, or3); -#endif - -#ifndef CONFIG_SYS_RAMBOOT - /* 60x SDRAM setup: - */ - size8 = try_init (memctl, CONFIG_SYS_PSDMR_8COL, CONFIG_SYS_OR1_8COL, - (uchar *) CONFIG_SYS_SDRAM_BASE); - size9 = try_init (memctl, CONFIG_SYS_PSDMR_9COL, CONFIG_SYS_OR1_9COL, - (uchar *) CONFIG_SYS_SDRAM_BASE); - - if (size8 < size9) { - psize = size9; - printf ("(60x:9COL - %ld MB, ", psize >> 20); - } else { - psize = try_init (memctl, CONFIG_SYS_PSDMR_8COL, CONFIG_SYS_OR1_8COL, - (uchar *) CONFIG_SYS_SDRAM_BASE); - printf ("(60x:8COL - %ld MB, ", psize >> 20); - } - - /* Local SDRAM setup: - */ -#ifdef CONFIG_SYS_INIT_LOCAL_SDRAM - memctl->memc_lsrt = CONFIG_SYS_LSRT; - size8 = try_init (memctl, CONFIG_SYS_LSDMR_8COL, CONFIG_SYS_OR2_8COL, - (uchar *) SDRAM_BASE2_PRELIM); - size9 = try_init (memctl, CONFIG_SYS_LSDMR_9COL, CONFIG_SYS_OR2_9COL, - (uchar *) SDRAM_BASE2_PRELIM); - - if (size8 < size9) { - lsize = size9; - printf ("Local:9COL - %ld MB) using ", lsize >> 20); - } else { - lsize = try_init (memctl, CONFIG_SYS_LSDMR_8COL, CONFIG_SYS_OR2_8COL, - (uchar *) SDRAM_BASE2_PRELIM); - printf ("Local:8COL - %ld MB) using ", lsize >> 20); - } - -#if 0 - /* Set up BR2 so that the local SDRAM goes - * right after the 60x SDRAM - */ - memctl->memc_br2 = (CONFIG_SYS_BR2_PRELIM & ~BRx_BA_MSK) | - (CONFIG_SYS_SDRAM_BASE + psize); -#endif -#endif /* CONFIG_SYS_INIT_LOCAL_SDRAM */ -#endif /* CONFIG_SYS_RAMBOOT */ - - icache_enable (); - - return (psize); -} - -/* ------------------------------------------------------------------------- */ diff --git a/configs/TQM8255_AA_defconfig b/configs/TQM8255_AA_defconfig deleted file mode 100644 index a9f9f015ff..0000000000 --- a/configs/TQM8255_AA_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="MPC8255,300MHz" -CONFIG_PPC=y -CONFIG_MPC8260=y -CONFIG_TARGET_TQM8260=y diff --git a/configs/TQM8260_AA_defconfig b/configs/TQM8260_AA_defconfig deleted file mode 100644 index b762fe4a0d..0000000000 --- a/configs/TQM8260_AA_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="MPC8260,200MHz" -CONFIG_PPC=y -CONFIG_MPC8260=y -CONFIG_TARGET_TQM8260=y diff --git a/configs/TQM8260_AB_defconfig b/configs/TQM8260_AB_defconfig deleted file mode 100644 index 6ff8d17117..0000000000 --- a/configs/TQM8260_AB_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="MPC8260,200MHz,L2_CACHE,BUSMODE_60x" -CONFIG_PPC=y -CONFIG_MPC8260=y -CONFIG_TARGET_TQM8260=y diff --git a/configs/TQM8260_AC_defconfig b/configs/TQM8260_AC_defconfig deleted file mode 100644 index 6ff8d17117..0000000000 --- a/configs/TQM8260_AC_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="MPC8260,200MHz,L2_CACHE,BUSMODE_60x" -CONFIG_PPC=y -CONFIG_MPC8260=y -CONFIG_TARGET_TQM8260=y diff --git a/configs/TQM8260_AD_defconfig b/configs/TQM8260_AD_defconfig deleted file mode 100644 index 3f406a4f29..0000000000 --- a/configs/TQM8260_AD_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="MPC8260,300MHz,BUSMODE_60x" -CONFIG_PPC=y -CONFIG_MPC8260=y -CONFIG_TARGET_TQM8260=y diff --git a/configs/TQM8260_AE_defconfig b/configs/TQM8260_AE_defconfig deleted file mode 100644 index 1077b19171..0000000000 --- a/configs/TQM8260_AE_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="MPC8260,266MHz" -CONFIG_PPC=y -CONFIG_MPC8260=y -CONFIG_TARGET_TQM8260=y diff --git a/configs/TQM8260_AF_defconfig b/configs/TQM8260_AF_defconfig deleted file mode 100644 index 3f406a4f29..0000000000 --- a/configs/TQM8260_AF_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="MPC8260,300MHz,BUSMODE_60x" -CONFIG_PPC=y -CONFIG_MPC8260=y -CONFIG_TARGET_TQM8260=y diff --git a/configs/TQM8260_AG_defconfig b/configs/TQM8260_AG_defconfig deleted file mode 100644 index b0d67fa326..0000000000 --- a/configs/TQM8260_AG_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="MPC8260,300MHz" -CONFIG_PPC=y -CONFIG_MPC8260=y -CONFIG_TARGET_TQM8260=y diff --git a/configs/TQM8260_AH_defconfig b/configs/TQM8260_AH_defconfig deleted file mode 100644 index 65c73e8309..0000000000 --- a/configs/TQM8260_AH_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="MPC8260,300MHz,L2_CACHE,BUSMODE_60x" -CONFIG_PPC=y -CONFIG_MPC8260=y -CONFIG_TARGET_TQM8260=y diff --git a/configs/TQM8260_AI_defconfig b/configs/TQM8260_AI_defconfig deleted file mode 100644 index 3f406a4f29..0000000000 --- a/configs/TQM8260_AI_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="MPC8260,300MHz,BUSMODE_60x" -CONFIG_PPC=y -CONFIG_MPC8260=y -CONFIG_TARGET_TQM8260=y diff --git a/configs/TQM8265_AA_defconfig b/configs/TQM8265_AA_defconfig deleted file mode 100644 index d8806c4bb4..0000000000 --- a/configs/TQM8265_AA_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="MPC8265,300MHz,BUSMODE_60x" -CONFIG_PPC=y -CONFIG_MPC8260=y -CONFIG_TARGET_TQM8260=y diff --git a/doc/README.scrapyard b/doc/README.scrapyard index f9cceb740c..566162ed16 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order. Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +TQM8260 powerpc mpc8260 - - Wolfgang Denk IDS8247 powerpc mpc8260 - - Heiko Schocher HWW1U1A powerpc mpc85xx - - Kyle Moffett hymod powerpc mpc8260 - - Murray Jensen diff --git a/include/configs/TQM8260.h b/include/configs/TQM8260.h deleted file mode 100644 index 7fd12d3fbc..0000000000 --- a/include/configs/TQM8260.h +++ /dev/null @@ -1,620 +0,0 @@ -/* - * (C) Copyright 2001-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * Imported from global configuration: - * CONFIG_MPC8255 - * CONFIG_MPC8265 - * CONFIG_200MHz - * CONFIG_266MHz - * CONFIG_300MHz - * CONFIG_L2_CACHE - * CONFIG_BUSMODE_60x - */ - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_SYS_TEXT_BASE 0x40000000 - - -#if 0 -#define CONFIG_TQM8260 100 /* ...on a TQM8260 module Rev.100 */ -#else -#define CONFIG_TQM8260 200 /* ...on a TQM8260 module Rev.200 */ -#endif - -#define CONFIG_CPM2 1 /* Has a CPM2 */ - -#define CONFIG_82xx_CONS_SMC1 1 /* console on SMC1 */ - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_BOOTCOUNT_LIMIT - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "rootpath=/opt/eldk/ppc_6xx\0" \ - "bootfile=tqm8260/uImage\0" \ - "kernel_addr=400C0000\0" \ - "ramdisk_addr=40240000\0" \ - "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -/* enable I2C and select the hardware/software driver */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SOFT_SPEED 400000 -#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F - -/* - * Software (bit-bang) I2C driver configuration - */ - -/* TQM8260 Rev.100 has the clock and data pins swapped (!!!) on EEPROM */ -#if (CONFIG_TQM8260 <= 100) - -#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ -#define I2C_ACTIVE (iop->pdir |= 0x00020000) -#define I2C_TRISTATE (iop->pdir &= ~0x00020000) -#define I2C_READ ((iop->pdat & 0x00020000) != 0) -#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00020000; \ - else iop->pdat &= ~0x00020000 -#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00010000; \ - else iop->pdat &= ~0x00010000 -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - -#else - -#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ -#define I2C_ACTIVE (iop->pdir |= 0x00010000) -#define I2C_TRISTATE (iop->pdir &= ~0x00010000) -#define I2C_READ ((iop->pdat & 0x00010000) != 0) -#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ - else iop->pdat &= ~0x00010000 -#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ - else iop->pdat &= ~0x00020000 -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#endif - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ - -#define CONFIG_I2C_X - -/* - * select serial console configuration - * - * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then - * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 - * for SCC). - * - * if CONFIG_CONS_NONE is defined, then the serial console routines must - * defined elsewhere (for example, on the cogent platform, there are serial - * ports on the motherboard which are used for the serial console - see - * cogent/cma101/serial.[ch]). - */ -#define CONFIG_CONS_ON_SMC /* define if console on SMC */ -#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on something else*/ -#ifdef CONFIG_82xx_CONS_SMC1 -#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ -#endif -#ifdef CONFIG_82xx_CONS_SMC2 -#define CONFIG_CONS_INDEX 2 /* which serial channel for console */ -#endif - -#undef CONFIG_CONS_USE_EXTC /* SMC/SCC use ext clock not brg_clk */ -#define CONFIG_CONS_EXTC_RATE 3686400 /* SMC/SCC ext clk rate in Hz */ -#define CONFIG_CONS_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9 */ - -/* - * select ethernet configuration - * - * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then - * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 - * for FCC) - * - * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be - * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. - * - * (On TQM8260 either SCC1 or FCC2 may be chosen: SCC1 is hardwired to the - * X.29 connector, and FCC2 is hardwired to the X.1 connector) - */ -#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ -#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ -#undef CONFIG_ETHER_NONE /* define if ether on something else */ -#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */ - -#if defined(CONFIG_ETHER_ON_SCC) && (CONFIG_ETHER_INDEX == 1) - -/* - * - RX clk is CLK11 - * - TX clk is CLK12 - */ -# define CONFIG_SYS_CMXSCR_VALUE1 (CMXSCR_RS1CS_CLK11 | CMXSCR_TS1CS_CLK12) - -#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) - -/* - * - Rx-CLK is CLK13 - * - Tx-CLK is CLK14 - * - RAM for BD/Buffers is on the 60x Bus (see 28-13) - * - Enable Full Duplex in FSMR - */ -# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK) -# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14) -# define CONFIG_SYS_CPMFCR_RAMTYPE 0 -# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) - -#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */ - - -/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ -#if defined(CONFIG_MPC8255) || defined(CONFIG_MPC8265) -# define CONFIG_8260_CLKIN 66666666 /* in Hz */ -#else /* !CONFIG_MPC8255 && !CONFIG_MPC8265 */ -# ifndef CONFIG_300MHz -# define CONFIG_8260_CLKIN 66666666 /* in Hz */ -# else -# define CONFIG_8260_CLKIN 83333000 /* in Hz */ -# endif -#endif /* CONFIG_MPC8255 */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_TIMESTAMP /* Print image info with timestamp */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_I2C -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_NFS -#define CONFIG_CMD_SNTP - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_RESET_ADDRESS 0xFFFFFFFC /* "bad" address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - - -/* What should the base address of the main FLASH be and how big is - * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/tqm8260/config.mk - * The main FLASH is whichever is connected to *CS0. - */ -#define CONFIG_SYS_FLASH0_BASE 0x40000000 -#define CONFIG_SYS_FLASH1_BASE 0x60000000 -#define CONFIG_SYS_FLASH0_SIZE 32 -#define CONFIG_SYS_FLASH1_SIZE 32 - -/* Flash bank size (for preliminary settings) - */ -#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - -/* use CFI flash driver */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } -#define CONFIG_SYS_FLASH_EMPTY_INFO 1 -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000) -#define CONFIG_ENV_SIZE 0x08000 -#define CONFIG_ENV_SECT_SIZE 0x40000 -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE - -/*----------------------------------------------------------------------- - * Hardware Information Block - */ -#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ -#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */ -#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ - -/*----------------------------------------------------------------------- - * Hard Reset Configuration Words - * - * if you change bits in the HRCW, you must also change the CONFIG_SYS_* - * defines for the various registers affected by the HRCW e.g. changing - * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR. - */ -#define __HRCW__ALL__ (HRCW_CIP | HRCW_ISB111 | HRCW_BMS) - -#if defined(CONFIG_MPC8255) || defined(CONFIG_MPC8265) -# define CONFIG_SYS_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0111) -#else /* ! MPC8255 && !MPC8265 */ -# if defined(CONFIG_266MHz) -# define CONFIG_SYS_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0111) -# elif defined(CONFIG_300MHz) -# define CONFIG_SYS_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0110) -# else -# define CONFIG_SYS_HRCW_MASTER (__HRCW__ALL__) -# endif -#endif /* CONFIG_MPC8255 */ - -/* no slaves so just fill with zeros */ -#define CONFIG_SYS_HRCW_SLAVE1 0 -#define CONFIG_SYS_HRCW_SLAVE2 0 -#define CONFIG_SYS_HRCW_SLAVE3 0 -#define CONFIG_SYS_HRCW_SLAVE4 0 -#define CONFIG_SYS_HRCW_SLAVE5 0 -#define CONFIG_SYS_HRCW_SLAVE6 0 -#define CONFIG_SYS_HRCW_SLAVE7 0 - -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFFF00000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - * - * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE, local SDRAM - * is mapped at SDRAM_BASE2_PRELIM. - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc()*/ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * HIDx - Hardware Implementation-dependent Registers 2-11 - *----------------------------------------------------------------------- - * HID0 also contains cache control - initially enable both caches and - * invalidate contents, then the final state leaves only the instruction - * cache enabled. Note that Power-On and Hard reset invalidate the caches, - * but Soft reset does not. - * - * HID1 has only read-only information - nothing to set. - */ -#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\ - HID0_IFEM|HID0_ABE) -#define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE) -#define CONFIG_SYS_HID2 0 - -/*----------------------------------------------------------------------- - * RMR - Reset Mode Register 5-5 - *----------------------------------------------------------------------- - * turn on Checkstop Reset Enable - */ -#define CONFIG_SYS_RMR RMR_CSRE - -/*----------------------------------------------------------------------- - * BCR - Bus Configuration 4-25 - *----------------------------------------------------------------------- - */ -#ifdef CONFIG_BUSMODE_60x -#define CONFIG_SYS_BCR (BCR_EBM|BCR_L2C|BCR_LETM|\ - BCR_NPQM0|BCR_NPQM1|BCR_NPQM2) /* 60x mode */ -#else -#define BCR_APD01 0x10000000 -#define CONFIG_SYS_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */ -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 4-31 - *----------------------------------------------------------------------- - */ -#if 0 -#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10) -#else -#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10) -#endif - - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 4-35 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ - SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ - SYPCR_SWRI|SYPCR_SWP) -#endif /* CONFIG_WATCHDOG */ - -/*----------------------------------------------------------------------- - * TMCNTSC - Time Counter Status and Control 4-40 - *----------------------------------------------------------------------- - * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, - * and enable Time Counter - */ -#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 4-42 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable - * Periodic timer - */ -#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) - -/*----------------------------------------------------------------------- - * SCCR - System Clock Control 9-8 - *----------------------------------------------------------------------- - * Ensure DFBRG is Divide by 16 - */ -#define CONFIG_SYS_SCCR 0 - -/*----------------------------------------------------------------------- - * RCCR - RISC Controller Configuration 13-7 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RCCR 0 - -/* - * Init Memory Controller: - * - * Bank Bus Machine PortSz Device - * ---- --- ------- ------ ------ - * 0 60x GPCM 64 bit FLASH - * 1 60x SDRAM 64 bit SDRAM - * 2 Local SDRAM 32 bit SDRAM - * - */ - - /* Initialize SDRAM on local bus - */ -#define CONFIG_SYS_INIT_LOCAL_SDRAM - -#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */ - -/* Minimum mask to separate preliminary - * address ranges for CS[0:2] - */ -#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (512<<20) /* less than 512 MB */ -#define CONFIG_SYS_LOCAL_SDRAM_LIMIT (128<<20) /* less than 128 MB */ - -#define CONFIG_SYS_MPTPR 0x4000 - -/*----------------------------------------------------------------------------- - * Address for Mode Register Set (MRS) command - *----------------------------------------------------------------------------- - * In fact, the address is rather configuration data presented to the SDRAM on - * its address lines. Because the address lines may be mux'ed externally either - * for 8 column or 9 column devices, some bits appear twice in the 8260's - * address: - * - * | (RFU) | (RFU) | WBL | TM | CL | BT | Burst Length | - * | BA1 BA0 | A12 : A10 | A9 | A8 A7 | A6 : A4 | A3 | A2 : A0 | - * 8 columns mux'ing: | A9 | A10 A21 | A22 : A24 | A25 | A26 : A28 | - * 9 columns mux'ing: | A8 | A20 A21 | A22 : A24 | A25 | A26 : A28 | - * Settings: | 0 | 0 0 | 0 1 0 | 0 | 0 1 0 | - *----------------------------------------------------------------------------- - */ -#define CONFIG_SYS_MRS_OFFS 0x00000110 - - -/* Bank 0 - FLASH - */ -#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\ - BRx_PS_64 |\ - BRx_MS_GPCM_P |\ - BRx_V) - -#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\ - ORxG_CSNT |\ - ORxG_ACS_DIV1 |\ - ORxG_SCY_3_CLK |\ - ORxG_EHTR |\ - ORxG_TRLX) - - /* SDRAM on TQM8260 can have either 8 or 9 columns. - * The number affects configuration values. - */ - -/* Bank 1 - 60x bus SDRAM - */ -#define CONFIG_SYS_PSRT 0x20 -#define CONFIG_SYS_LSRT 0x20 -#ifndef CONFIG_SYS_RAMBOOT -#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\ - BRx_PS_64 |\ - BRx_MS_SDRAM_P |\ - BRx_V) - -#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1_8COL - - - /* SDRAM initialization values for 8-column chips - */ -#define CONFIG_SYS_OR1_8COL ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ - ORxS_BPD_4 |\ - ORxS_ROWST_PBI1_A7 |\ - ORxS_NUMR_12) - -#define CONFIG_SYS_PSDMR_8COL (PSDMR_PBI |\ - PSDMR_SDAM_A15_IS_A5 |\ - PSDMR_BSMA_A12_A14 |\ - PSDMR_SDA10_PBI1_A8 |\ - PSDMR_RFRC_7_CLK |\ - PSDMR_PRETOACT_2W |\ - PSDMR_ACTTORW_2W |\ - PSDMR_LDOTOPRE_1C |\ - PSDMR_WRC_2C |\ - PSDMR_EAMUX |\ - PSDMR_CL_2) - - /* SDRAM initialization values for 9-column chips - */ -#define CONFIG_SYS_OR1_9COL ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ - ORxS_BPD_4 |\ - ORxS_ROWST_PBI1_A5 |\ - ORxS_NUMR_13) - -#define CONFIG_SYS_PSDMR_9COL (PSDMR_PBI |\ - PSDMR_SDAM_A16_IS_A5 |\ - PSDMR_BSMA_A12_A14 |\ - PSDMR_SDA10_PBI1_A7 |\ - PSDMR_RFRC_7_CLK |\ - PSDMR_PRETOACT_2W |\ - PSDMR_ACTTORW_2W |\ - PSDMR_LDOTOPRE_1C |\ - PSDMR_WRC_2C |\ - PSDMR_EAMUX |\ - PSDMR_CL_2) - -/* Bank 2 - Local bus SDRAM - */ -#ifdef CONFIG_SYS_INIT_LOCAL_SDRAM -#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BRx_BA_MSK) |\ - BRx_PS_32 |\ - BRx_MS_SDRAM_L |\ - BRx_V) - -#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_OR2_8COL - -#define SDRAM_BASE2_PRELIM 0x80000000 - - /* SDRAM initialization values for 8-column chips - */ -#define CONFIG_SYS_OR2_8COL ((~(CONFIG_SYS_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ - ORxS_BPD_4 |\ - ORxS_ROWST_PBI1_A8 |\ - ORxS_NUMR_12) - -#define CONFIG_SYS_LSDMR_8COL (PSDMR_PBI |\ - PSDMR_SDAM_A15_IS_A5 |\ - PSDMR_BSMA_A13_A15 |\ - PSDMR_SDA10_PBI1_A9 |\ - PSDMR_RFRC_7_CLK |\ - PSDMR_PRETOACT_2W |\ - PSDMR_ACTTORW_2W |\ - PSDMR_BL |\ - PSDMR_LDOTOPRE_1C |\ - PSDMR_WRC_2C |\ - PSDMR_CL_2) - - /* SDRAM initialization values for 9-column chips - */ -#define CONFIG_SYS_OR2_9COL ((~(CONFIG_SYS_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ - ORxS_BPD_4 |\ - ORxS_ROWST_PBI1_A6 |\ - ORxS_NUMR_13) - -#define CONFIG_SYS_LSDMR_9COL (PSDMR_PBI |\ - PSDMR_SDAM_A16_IS_A5 |\ - PSDMR_BSMA_A13_A15 |\ - PSDMR_SDA10_PBI1_A8 |\ - PSDMR_RFRC_7_CLK |\ - PSDMR_PRETOACT_2W |\ - PSDMR_ACTTORW_2W |\ - PSDMR_BL |\ - PSDMR_LDOTOPRE_1C |\ - PSDMR_WRC_2C |\ - PSDMR_CL_2) - -#endif /* CONFIG_SYS_INIT_LOCAL_SDRAM */ - -#endif /* CONFIG_SYS_RAMBOOT */ - -#endif /* __CONFIG_H */